- 根目录:
- drivers
- staging
- rtl8192u
- r819xU_phy.c
#include "r8192U.h"
#include "r8192U_hw.h"
#include "r819xU_phy.h"
#include "r819xU_phyreg.h"
#include "r8190_rtl8256.h"
#include "r8192U_dm.h"
#include "r819xU_firmware_img.h"
#include "dot11d.h"
#include <linux/bitops.h>
static u32 RF_CHANNEL_TABLE_ZEBRA[] = {
0,
0x085c, /* 2412 1 */
0x08dc, /* 2417 2 */
0x095c, /* 2422 3 */
0x09dc, /* 2427 4 */
0x0a5c, /* 2432 5 */
0x0adc, /* 2437 6 */
0x0b5c, /* 2442 7 */
0x0bdc, /* 2447 8 */
0x0c5c, /* 2452 9 */
0x0cdc, /* 2457 10 */
0x0d5c, /* 2462 11 */
0x0ddc, /* 2467 12 */
0x0e5c, /* 2472 13 */
0x0f72, /* 2484 */
};
#define rtl819XPHY_REG_1T2RArray Rtl8192UsbPHY_REG_1T2RArray
#define rtl819XMACPHY_Array_PG Rtl8192UsbMACPHY_Array_PG
#define rtl819XMACPHY_Array Rtl8192UsbMACPHY_Array
#define rtl819XRadioA_Array Rtl8192UsbRadioA_Array
#define rtl819XRadioB_Array Rtl8192UsbRadioB_Array
#define rtl819XRadioC_Array Rtl8192UsbRadioC_Array
#define rtl819XRadioD_Array Rtl8192UsbRadioD_Array
#define rtl819XAGCTAB_Array Rtl8192UsbAGCTAB_Array
/******************************************************************************
* function: This function reads BB parameters from header file we generate,
* and does register read/write
* input: u32 bitmask //taget bit pos in the addr to be modified
* output: none
* return: u32 return the shift bit position of the mask
******************************************************************************/
static u32 rtl8192_CalculateBitShift(u32 bitmask)
{
u32 i;
i = ffs(bitmask) - 1;
return i;
}
/******************************************************************************
* function: This function checks different RF type to execute legal judgement.
* If RF Path is illegal, we will return false.
* input: net_device *dev
* u32 eRFPath
* output: none
* return: 0(illegal, false), 1(legal, true)
*****************************************************************************/
u8 rtl8192_phy_CheckIsLegalRFPath(struct net_device *dev, u32 eRFPath)
{
u8 ret = 1;
struct r8192_priv *priv = ieee80211_priv(dev);
if (priv->rf_type == RF_2T4R) {
ret = 0;
} else if (priv->rf_type == RF_1T2R) {
if (eRFPath == RF90_PATH_A || eRFPath == RF90_PATH_B)
ret = 1;
else if (eRFPath == RF90_PATH_C || eRFPath == RF90_PATH_D)
ret = 0;
}
return ret;
}
/******************************************************************************
* function: This function sets specific bits to BB register
* input: net_device *dev
* u32 reg_addr //target addr to be modified
* u32 bitmask //taget bit pos to be modified
* u32 data //value to be write
* output: none
* return: none
* notice:
******************************************************************************/
void rtl8192_setBBreg(struct net_device *dev, u32 reg_addr, u32 bitmask,
u32 data)
{
u32 reg, bitshift;
if (bitmask != bMaskDWord) {
read_nic_dword(dev, reg_addr, ®);
bitshift = rtl8192_CalculateBitShift(bitmask);
reg &= ~bitmask;
reg |= data << bitshift;
write_nic_dword(dev, reg_addr, reg);
} else {
write_nic_dword(dev, reg_addr, data);
}
}
/******************************************************************************
* function: This function reads specific bits from BB register
* input: net_device *dev
* u32 reg_addr //target addr to be readback
* u32 bitmask //taget bit pos to be readback
* output: none
* return: u32 data //the readback register value
* notice:
******************************************************************************/
u32 rtl8192_QueryBBReg(struct net_device *dev, u32 reg_addr, u32 bitmask)
{
u32 reg, bitshift;
read_nic_dword(dev, reg_addr, ®);
bitshift = rtl8192_CalculateBitShift(bitmask);
return (reg & bitmask) >> bitshift;
}
static u32 phy_FwRFSerialRead(struct net_device *dev, RF90_RADIO_PATH_E eRFPath,
u32 offset);
static void phy_FwRFSerialWrite(struct net_device *dev,
RF90_RADIO_PATH_E eRFPath, u32 offset,
u32 data);
/******************************************************************************
* function: This function reads register from RF chip
* input: net_device *dev
* RF90_RADIO_PATH_E eRFPath //radio path of A/B/C/D
* u32 offset //target address to be read
* output: none
* return: u32 readback value
* notice: There are three types of serial operations:
* (1) Software serial write.
* (2)Hardware LSSI-Low Speed Serial Interface.
* (3)Hardware HSSI-High speed serial write.
* Driver here need to implement (1) and (2)
* ---need more spec for this information.
******************************************************************************/
static u32 rtl8192_phy_RFSerialRead(struct net_device *dev,
RF90_RADIO_PATH_E eRFPath, u32 offset)
{
struct r8192_priv *priv = ieee80211_priv(dev);
u32 ret = 0;
u32 new_offset = 0;
BB_REGISTER_DEFINITION_T *pPhyReg = &priv->PHYRegDef[eRFPath];
rtl8192_setBBreg(dev, pPhyReg->rfLSSIReadBack, bLSSIReadBackData, 0);
/* Make sure RF register offset is correct */
offset &= 0x3f;
/* Switch page for 8256 RF IC */
if (priv->rf_chip == RF_8256) {
if (offset >= 31) {
priv->RfReg0Value[eRFPath] |= 0x140;
/* Switch to Reg_Mode2 for Reg 31-45 */
rtl8192_setBBreg(dev, pPhyReg->rf3wireOffset,
bMaskDWord,
priv->RfReg0Value[eRFPath]<<16);
/* Modify offset */
new_offset = offset - 30;
} else if (offset >= 16) {
priv->RfReg0Value[eRFPath] |= 0x100;
priv->RfReg0Value[eRFPath] &= (~0x40);
/* Switch to Reg_Mode1 for Reg16-30 */
rtl8192_setBBreg(dev, pPhyReg->rf3wireOffset,
bMaskDWord,
priv->RfReg0Value[eRFPath]<<16);
new_offset = offset - 15;
} else {
new_offset = offset;
}
} else {
RT_TRACE((COMP_PHY|COMP_ERR),
"check RF type here, need to be 8256\n");
new_offset = offset;
}
/* Put desired read addr to LSSI control Register */
rtl8192_setBBreg(dev, pPhyReg->rfHSSIPara2, bLSSIReadAddress,
new_offset);
/* Issue a posedge trigger */
rtl8192_setBBreg(dev, pPhyReg->rfHSSIPara2, bLSSIReadEdge, 0x0);
rtl8192_setBBreg(dev, pPhyReg->rfHSSIPara2, bLSSIReadEdge, 0x1);
/* TODO: we should not delay such a long time. Ask for help from SD3 */
usleep_range(1000, 1000);
ret = rtl8192_QueryBBReg(dev, pPhyReg->rfLSSIReadBack,
bLSSIReadBackData);
/* Switch back to Reg_Mode0 */
if (priv->rf_chip == RF_8256) {
priv->RfReg0Value[eRFPath] &= 0xebf;
rtl8192_setBBreg(dev, pPhyReg->rf3wireOffset, bMaskDWord,
priv->RfReg0Value[eRFPath] << 16);
}
return ret;
}
/******************************************************************************
* function: This function writes data to RF register
* input: net_device *dev
* RF90_RADIO_PATH_E eRFPath //radio path of A/B/C/D
* u32 offset //target address to be written
* u32 data //the new register data to be written
* output: none
* return: none
* notice: For RF8256 only.
* ===========================================================================
* Reg Mode RegCTL[1] RegCTL[0] Note
* (Reg00[12]) (Reg00[10])
* ===========================================================================
* Reg_Mode0 0 x Reg 0 ~ 15(0x0 ~ 0xf)
* ---------------------------------------------------------------------------
* Reg_Mode1 1 0 Reg 16 ~ 30(0x1 ~ 0xf)
* ---------------------------------------------------------------------------
* Reg_Mode2 1 1 Reg 31 ~ 45(0x1 ~ 0xf)
* ---------------------------------------------------------------------------
*****************************************************************************/
static void rtl8192_phy_RFSerialWrite(struct net_device *dev,
RF90_RADIO_PATH_E eRFPath, u32 offset,
u32 data)
{
struct r8192_priv *priv = ieee80211_priv(dev);
u32 DataAndAddr = 0, new_offset = 0;
BB_REGISTER_DEFINITION_T *pPhyReg = &priv->PHYRegDef[eRFPath];
offset &= 0x3f;
if (priv->rf_chip == RF_8256) {
if (offset >= 31) {
priv->RfReg0Value[eRFPath] |= 0x140;
rtl8192_setBBreg(dev, pPhyReg->rf3wireOffset,
bMaskDWord,
priv->RfReg0Value[eRFPath] << 16);
new_offset = offset - 30;
} else if (offset >= 16) {
priv->RfReg0Value[eRFPath] |= 0x100;
priv->RfReg0Value[eRFPath] &= (~0x40);
rtl8192_setBBreg(dev, pPhyReg->rf3wireOffset,
bMaskDWord,
priv->RfReg0Value[eRFPath]<<16);
new_offset = offset - 15;
} else {
new_offset = offset;
}
} else {
RT_TRACE((COMP_PHY|COMP_ERR),
"check RF type here, need to be 8256\n");
new_offset = offset;
}
/* Put write addr in [5:0] and write data in [31:16] */
DataAndAddr = (data<<16) | (new_offset&0x3f);
/* Write operation */
rtl8192_setBBreg(dev, pPhyReg->rf3wireOffset, bMaskDWord, DataAndAddr);
if (offset == 0x0)
priv->RfReg0Value[eRFPath] = data;
/* Switch back to Reg_Mode0 */
if (priv->rf_chip == RF_8256) {
if (offset != 0) {
priv->RfReg0Value[eRFPath] &= 0xebf;
rtl8192_setBBreg(dev, pPhyReg->rf3wireOffset,
bMaskDWord,
priv->RfReg0Value[eRFPath] << 16);
}
}
}
/******************************************************************************
* function: This function set specific bits to RF register
* input: net_device dev
* RF90_RADIO_PATH_E eRFPath //radio path of A/B/C/D
* u32 reg_addr //target addr to be modified
* u32 bitmask //taget bit pos to be modified
* u32 data //value to be written
* output: none
* return: none
* notice:
*****************************************************************************/
void rtl8192_phy_SetRFReg(struct net_device *dev, RF90_RADIO_PATH_E eRFPath,
u32 reg_addr, u32 bitmask, u32 data)
{
struct r8192_priv *priv = ieee80211_priv(dev);
u32 reg, bitshift;
if (!rtl8192_phy_CheckIsLegalRFPath(dev, eRFPath))
return;
if (priv->Rf_Mode == RF_OP_By_FW) {
if (bitmask != bMask12Bits) {
/* RF data is 12 bits only */
reg = phy_FwRFSerialRead(dev, eRFPath, reg_addr);
bitshift = rtl8192_CalculateBitShift(bitmask);
reg &= ~bitmask;
reg |= data << bitshift;
phy_FwRFSerialWrite(dev, eRFPath, reg_addr, reg);
} else {
phy_FwRFSerialWrite(dev, eRFPath, reg_addr, data);
}
udelay(200);
} else {
if (bitmask != bMask12Bits) {
/* RF data is 12 bits only */
reg = rtl8192_phy_RFSerialRead(dev, eRFPath, reg_addr);
bitshift = rtl8192_CalculateBitShift(bitmask);
reg &= ~bitmask;
reg |= data << bitshift;
rtl8192_phy_RFSerialWrite(dev, eRFPath, reg_addr, reg);
} else {
rtl8192_phy_RFSerialWrite(dev, eRFPath, reg_addr, data);
}
}
}
/******************************************************************************
* function: This function reads specific bits from RF register
* input: net_device *dev
* u32 reg_addr //target addr to be readback
* u32 bitmask //taget bit pos to be readback
* output: none
* return: u32 data //the readback register value
* notice:
*****************************************************************************/
u32 rtl8192_phy_QueryRFReg(struct net_device *dev, RF90_RADIO_PATH_E eRFPath,
u32 reg_addr, u32 bitmask)
{
u32 reg, bitshift;
struct r8192_priv *priv = ieee80211_priv(dev);
if (!rtl8192_phy_CheckIsLegalRFPath(dev, eRFPath))
return 0;
if (priv->Rf_Mode == RF_OP_By_FW) {
reg = phy_FwRFSerialRead(dev, eRFPath, reg_addr);
udelay(200);
} else {
reg = rtl8192_phy_RFSerialRead(dev, eRFPath, reg_addr);
}
bitshift = rtl8192_CalculateBitShift(bitmask);
reg = (reg & bitmask) >> bitshift;
return reg;
}
/******************************************************************************
* function: We support firmware to execute RF-R/W.
* input: net_device *dev
* RF90_RADIO_PATH_E eRFPath
* u32 offset
* output: none
* return: u32
* notice:
****************************************************************************/
static u32 phy_FwRFSerialRead(struct net_device *dev, RF90_RADIO_PATH_E eRFPath,
u32 offset)
{
u32 reg = 0;
u32 data = 0;
u8 time = 0;
u32 tmp;
/* Firmware RF Write control.
* We can not execute the scheme in the initial step.
* Otherwise, RF-R/W will waste much time.
* This is only for site survey. */
/* 1. Read operation need not insert data. bit 0-11 */
/* 2. Write RF register address. bit 12-19 */
data |= ((offset&0xFF)<<12);
/* 3. Write RF path. bit 20-21 */
data |= ((eRFPath&0x3)<<20);
/* 4. Set RF read indicator. bit 22=0 */
/* 5. Trigger Fw to operate the command. bit 31 */
data |= 0x80000000;
/* 6. We can not execute read operation if bit 31 is 1. */
read_nic_dword(dev, QPNR, &tmp);
while (tmp & 0x80000000) {
/* If FW can not finish RF-R/W for more than ?? times.
We must reset FW. */
if (time++ < 100) {
udelay(10);
read_nic_dword(dev, QPNR, &tmp);
} else {
break;
}
}
/* 7. Execute read operation. */
write_nic_dword(dev, QPNR, data);
/* 8. Check if firmware send back RF content. */
read_nic_dword(dev, QPNR, &tmp);
while (tmp & 0x80000000) {
/* If FW can not finish RF-R/W for more than ?? times.
We must reset FW. */
if (time++ < 100) {
udelay(10);
read_nic_dword(dev, QPNR, &tmp);
} else {
return 0;
}
}
read_nic_dword(dev, RF_DATA, ®);
return reg;
}
/******************************************************************************
* function: We support firmware to execute RF-R/W.
* input: net_device *dev
* RF90_RADIO_PATH_E eRFPath
* u32 offset
* u32 data
* output: none
* return: none
* notice:
****************************************************************************/
static void phy_FwRFSerialWrite(struct net_device *dev,
RF90_RADIO_PATH_E eRFPath, u32 offset, u32 data)
{
u8 time = 0;
u32 tmp;
/* Firmware RF Write control.
* We can not execute the scheme in the initial step.
* Otherwise, RF-R/W will waste much time.
* This is only for site survey. */
/* 1. Set driver write bit and 12 bit data. bit 0-11 */
/* 2. Write RF register address. bit 12-19 */
data |= ((offset&0xFF)<<12);
/* 3. Write RF path. bit 20-21 */
data |= ((eRFPath&0x3)<<20);
/* 4. Set RF write indicator. bit 22=1 */
data |= 0x400000;
/* 5. Trigger Fw to operate the command. bit 31=1 */
data |= 0x80000000;
/* 6. Write operation. We can not write if bit 31 is 1. */
read_nic_dword(dev, QPNR, &tmp);
while (tmp & 0x80000000) {
/* If FW can not finish RF-R/W for more than ?? times.
We must reset FW. */
if (time++ < 100) {
udelay(10);
read_nic_dword(dev, QPNR, &tmp);
} else {
break;
}
}
/* 7. No matter check bit. We always force the write.
Because FW will not accept the command. */
write_nic_dword(dev, QPNR, data);
/* According to test, we must delay 20us to wait firmware
to finish RF write operation. */
/* We support delay in firmware side now. */
}
/******************************************************************************
* function: This function reads BB parameters from header file we generate,
* and do register read/write
* input: net_device *dev
* output: none
* return: none
* notice: BB parameters may change all the time, so please make
* sure it has been synced with the newest.
*****************************************************************************/
void rtl8192_phy_configmac(struct net_device *dev)
{
u32 dwArrayLen = 0, i;
u32 *pdwArray = NULL;
struct r8192_priv *priv = ieee80211_priv(dev);
if (priv->btxpowerdata_readfromEEPORM) {
RT_TRACE(COMP_PHY, "Rtl819XMACPHY_Array_PG\n");
dwArrayLen = MACPHY_Array_PGLength;
pdwArray = rtl819XMACPHY_Array_PG;
} else {
RT_TRACE(COMP_PHY, "Rtl819XMACPHY_Array\n");
dwArrayLen = MACPHY_ArrayLength;
pdwArray = rtl819XMACPHY_Array;
}
for (i = 0; i < dwArrayLen; i = i+3) {
if (pdwArray[i] == 0x318)
pdwArray[i+2] = 0x00000800;
RT_TRACE(COMP_DBG,
"Rtl8190MACPHY_Array[0]=%x Rtl8190MACPHY_Array[1]=%x Rtl8190MACPHY_Array[2]=%x\n",
pdwArray[i], pdwArray[i+1], pdwArray[i+2]);
rtl8192_setBBreg(dev, pdwArray[i], pdwArray[i+1],
pdwArray[i+2]);
}
}
/******************************************************************************
* function: This function does dirty work
* input: net_device *dev
* u8 ConfigType
* output: none
* return: none
* notice: BB parameters may change all the time, so please make
* sure it has been synced with the newest.
*****************************************************************************/
void rtl8192_phyConfigBB(struct net_device *dev, u8 ConfigType)
{
u32 i;
#ifdef TO_DO_LIST
u32 *rtl8192PhyRegArrayTable = NULL, *rtl8192AgcTabArrayTable = NULL;
if (Adapter->bInHctTest) {
PHY_REGArrayLen = PHY_REGArrayLengthDTM;
AGCTAB_ArrayLen = AGCTAB_ArrayLengthDTM;
Rtl8190PHY_REGArray_Table = Rtl819XPHY_REGArrayDTM;
Rtl8190AGCTAB_Array_Table = Rtl819XAGCTAB_ArrayDTM;
}
#endif
if (ConfigType == BaseBand_Config_PHY_REG) {
for (i = 0; i < PHY_REG_1T2RArrayLength; i += 2) {
rtl8192_setBBreg(dev, rtl819XPHY_REG_1T2RArray[i],
bMaskDWord,
rtl819XPHY_REG_1T2RArray[i+1]);
RT_TRACE(COMP_DBG,
"i: %x, Rtl819xUsbPHY_REGArray[0]=%x Rtl819xUsbPHY_REGArray[1]=%x\n",
i, rtl819XPHY_REG_1T2RArray[i],
rtl819XPHY_REG_1T2RArray[i+1]);
}
} else if (ConfigType == BaseBand_Config_AGC_TAB) {
for (i = 0; i < AGCTAB_ArrayLength; i += 2) {
rtl8192_setBBreg(dev, rtl819XAGCTAB_Array[i],
bMaskDWord, rtl819XAGCTAB_Array[i+1]);
RT_TRACE(COMP_DBG,
"i: %x, rtl819XAGCTAB_Array[0]=%x rtl819XAGCTAB_Array[1]=%x\n",
i, rtl819XAGCTAB_Array[i],
rtl819XAGCTAB_Array[i+1]);
}
}
}
/******************************************************************************
* function: This function initializes Register definition offset for
* Radio Path A/B/C/D
* input: net_device *dev
* output: none
* return: none
* notice: Initialization value here is constant and it should never
* be changed
*****************************************************************************/
static void rtl8192_InitBBRFRegDef(struct net_device *dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
/* RF Interface Software Control */
/* 16 LSBs if read 32-bit from 0x870 */
priv->PHYRegDef[RF90_PATH_A].rfintfs = rFPGA0_XAB_RFInterfaceSW;
/* 16 MSBs if read 32-bit from 0x870 (16-bit for 0x872) */
priv->PHYRegDef[RF90_PATH_B].rfintfs = rFPGA0_XAB_RFInterfaceSW;
/* 16 LSBs if read 32-bit from 0x874 */
priv->PHYRegDef[RF90_PATH_C].rfintfs = rFPGA0_XCD_RFInterfaceSW;
/* 16 MSBs if read 32-bit from 0x874 (16-bit for 0x876) */
priv->PHYRegDef[RF90_PATH_D].rfintfs = rFPGA0_XCD_RFInterfaceSW;
/* RF Interface Readback Value */
/* 16 LSBs if read 32-bit from 0x8E0 */
priv->PHYRegDef[RF90_PATH_A].rfintfi = rFPGA0_XAB_RFInterfaceRB;
/* 16 MSBs if read 32-bit from 0x8E0 (16-bit for 0x8E2) */
priv->PHYRegDef[RF90_PATH_B].rfintfi = rFPGA0_XAB_RFInterfaceRB;
/* 16 LSBs if read 32-bit from 0x8E4 */
priv->PHYRegDef[RF90_PATH_C].rfintfi = rFPGA0_XCD_RFInterfaceRB;
/* 16 MSBs if read 32-bit from 0x8E4 (16-bit for 0x8E6) */
priv->PHYRegDef[RF90_PATH_D].rfintfi = rFPGA0_XCD_RFInterfaceRB;
/* RF Interface Output (and Enable) */
/* 16 LSBs if read 32-bit from 0x860 */
priv->PHYRegDef[RF90_PATH_A].rfintfo = rFPGA0_XA_RFInterfaceOE;
/* 16 LSBs if read 32-bit from 0x864 */
priv->PHYRegDef[RF90_PATH_B].rfintfo = rFPGA0_XB_RFInterfaceOE;
/* 16 LSBs if read 32-bit from 0x868 */
priv->PHYRegDef[RF90_PATH_C].rfintfo = rFPGA0_XC_RFInterfaceOE;
/* 16 LSBs if read 32-bit from 0x86C */
priv->PHYRegDef[RF90_PATH_D].rfintfo = rFPGA0_XD_RFInterfaceOE;
/* RF Interface (Output and) Enable */
/* 16 MSBs if read 32-bit from 0x860 (16-bit for 0x862) */
priv->PHYRegDef[RF90_PATH_A].rfintfe = rFPGA0_XA_RFInterfaceOE;
/* 16 MSBs if read 32-bit from 0x864 (16-bit for 0x866) */
priv->PHYRegDef[RF90_PATH_B].rfintfe = rFPGA0_XB_RFInterfaceOE;
/* 16 MSBs if read 32-bit from 0x86A (16-bit for 0x86A) */
priv->PHYRegDef[RF90_PATH_C].rfintfe = rFPGA0_XC_RFInterfaceOE;
/* 16 MSBs if read 32-bit from 0x86C (16-bit for 0x86E) */
priv->PHYRegDef[RF90_PATH_D].rfintfe = rFPGA0_XD_RFInterfaceOE;
/* Addr of LSSI. Write RF register by driver */
priv->PHYRegDef[RF90_PATH_A].rf3wireOffset = rFPGA0_XA_LSSIParameter;
priv->PHYRegDef[RF90_PATH_B].rf3wireOffset = rFPGA0_XB_LSSIParameter;
priv->PHYRegDef[RF90_PATH_C].rf3wireOffset = rFPGA0_XC_LSSIParameter;
priv->PHYRegDef[RF90_PATH_D].rf3wireOffset = rFPGA0_XD_LSSIParameter;
/* RF parameter */
/* BB Band Select */
priv->PHYRegDef[RF90_PATH_A].rfLSSI_Select = rFPGA0_XAB_RFParameter;
priv->PHYRegDef[RF90_PATH_B].rfLSSI_Select = rFPGA0_XAB_RFParameter;
priv->PHYRegDef[RF90_PATH_C].rfLSSI_Select = rFPGA0_XCD_RFParameter;
priv->PHYRegDef[RF90_PATH_D].rfLSSI_Select = rFPGA0_XCD_RFParameter;
/* Tx AGC Gain Stage (same for all path. Should we remove this?) */
priv->PHYRegDef[RF90_PATH_A].rfTxGainStage = rFPGA0_TxGainStage;
priv->PHYRegDef[RF90_PATH_B].rfTxGainStage = rFPGA0_TxGainStage;
priv->PHYRegDef[RF90_PATH_C].rfTxGainStage = rFPGA0_TxGainStage;
priv->PHYRegDef[RF90_PATH_D].rfTxGainStage = rFPGA0_TxGainStage;
/* Tranceiver A~D HSSI Parameter-1 */
/* wire control parameter1 */
priv->PHYRegDef[RF90_PATH_A].rfHSSIPara1 = rFPGA0_XA_HSSIParameter1;
priv->PHYRegDef[RF90_PATH_B].rfHSSIPara1 = rFPGA0_XB_HSSIParameter1;
priv->PHYRegDef[RF90_PATH_C].rfHSSIPara1 = rFPGA0_XC_HSSIParameter1;
priv->PHYRegDef[RF90_PATH_D].rfHSSIPara1 = rFPGA0_XD_HSSIParameter1;
/* Tranceiver A~D HSSI Parameter-2 */
/* wire control parameter2 */
priv->PHYRegDef[RF90_PATH_A].rfHSSIPara2 = rFPGA0_XA_HSSIParameter2;
priv->PHYRegDef[RF90_PATH_B].rfHSSIPara2 = rFPGA0_XB_HSSIParameter2;
priv->PHYRegDef[RF90_PATH_C].rfHSSIPara2 = rFPGA0_XC_HSSIParameter2;
priv->PHYRegDef[RF90_PATH_D].rfHSSIPara2 = rFPGA0_XD_HSSIParameter2;
/* RF Switch Control */
/* TR/Ant switch control */
priv->PHYRegDef[RF90_PATH_A].rfSwitchControl = rFPGA0_XAB_SwitchControl;
priv->PHYRegDef[RF90_PATH_B].rfSwitchControl = rFPGA0_XAB_SwitchControl;
priv->PHYRegDef[RF90_PATH_C].rfSwitchControl = rFPGA0_XCD_SwitchControl;
priv->PHYRegDef[RF90_PATH_D].rfSwitchControl = rFPGA0_XCD_SwitchControl;
/* AGC control 1 */
priv->PHYRegDef[RF90_PATH_A].rfAGCControl1 = rOFDM0_XAAGCCore1;
priv->PHYRegDef[RF90_PATH_B].rfAGCControl1 = rOFDM0_XBAGCCore1;
priv->PHYRegDef[RF90_PATH_C].rfAGCControl1 = rOFDM0_XCAGCCore1;
priv->PHYRegDef[RF90_PATH_D].rfAGCControl1 = rOFDM0_XDAGCCore1;
/* AGC control 2 */
priv->PHYRegDef[RF90_PATH_A].rfAGCControl2 = rOFDM0_XAAGCCore2;
priv->PHYRegDef[RF90_PATH_B].rfAGCControl2 = rOFDM0_XBAGCCore2;
priv->PHYRegDef[RF90_PATH_C].rfAGCControl2 = rOFDM0_XCAGCCore2;
priv->PHYRegDef[RF90_PATH_D].rfAGCControl2 = rOFDM0_XDAGCCore2;
/* RX AFE control 1 */
priv->PHYRegDef[RF90_PATH_A].rfRxIQImbalance = rOFDM0_XARxIQImbalance;
priv->PHYRegDef[RF90_PATH_B].rfRxIQImbalance = rOFDM0_XBRxIQImbalance;
priv->PHYRegDef[RF90_PATH_C].rfRxIQImbalance = rOFDM0_XCRxIQImbalance;
priv->PHYRegDef[RF90_PATH_D].rfRxIQImbalance = rOFDM0_XDRxIQImbalance;
/* RX AFE control 1 */
priv->PHYRegDef[RF90_PATH_A].rfRxAFE = rOFDM0_XARxAFE;
priv->PHYRegDef[RF90_PATH_B].rfRxAFE = rOFDM0_XBRxAFE;
priv->PHYRegDef[RF90_PATH_C].rfRxAFE = rOFDM0_XCRxAFE;
priv->PHYRegDef[RF90_PATH_D].rfRxAFE = rOFDM0_XDRxAFE;
/* Tx AFE control 1 */
priv->PHYRegDef[RF90_PATH_A].rfTxIQImbalance = rOFDM0_XATxIQImbalance;
priv->PHYRegDef[RF90_PATH_B].rfTxIQImbalance = rOFDM0_XBTxIQImbalance;
priv->PHYRegDef[RF90_PATH_C].rfTxIQImbalance = rOFDM0_XCTxIQImbalance;
priv->PHYRegDef[RF90_PATH_D].rfTxIQImbalance = rOFDM0_XDTxIQImbalance;
/* Tx AFE control 2 */
priv->PHYRegDef[RF90_PATH_A].rfTxAFE = rOFDM0_XATxAFE;
priv->PHYRegDef[RF90_PATH_B].rfTxAFE = rOFDM0_XBTxAFE;
priv->PHYRegDef[RF90_PATH_C].rfTxAFE = rOFDM0_XCTxAFE;
priv->PHYRegDef[RF90_PATH_D].rfTxAFE = rOFDM0_XDTxAFE;
/* Tranceiver LSSI Readback */
priv->PHYRegDef[RF90_PATH_A].rfLSSIReadBack = rFPGA0_XA_LSSIReadBack;
priv->PHYRegDef[RF90_PATH_B].rfLSSIReadBack = rFPGA0_XB_LSSIReadBack;
priv->PHYRegDef[RF90_PATH_C].rfLSSIReadBack = rFPGA0_XC_LSSIReadBack;
priv->PHYRegDef[RF90_PATH_D].rfLSSIReadBack = rFPGA0_XD_LSSIReadBack;
}
/******************************************************************************
* function: This function is to write register and then readback to make
* sure whether BB and RF is OK
* input: net_device *dev
* HW90_BLOCK_E CheckBlock
* RF90_RADIO_PATH_E eRFPath //only used when checkblock is
* //HW90_BLOCK_RF
* output: none
* return: return whether BB and RF is ok (0:OK, 1:Fail)
* notice: This function may be removed in the ASIC
******************************************************************************/
u8 rtl8192_phy_checkBBAndRF(struct net_device *dev, HW90_BLOCK_E CheckBlock,
RF90_RADIO_PATH_E eRFPath)
{
u8 ret = 0;
u32 i, CheckTimes = 4, reg = 0;
u32 WriteAddr[4];
u32 WriteData[] = {0xfffff027, 0xaa55a02f, 0x00000027, 0x55aa502f};
/* Initialize register address offset to be checked */
WriteAddr[HW90_BLOCK_MAC] = 0x100;
WriteAddr[HW90_BLOCK_PHY0] = 0x900;
WriteAddr[HW90_BLOCK_PHY1] = 0x800;
WriteAddr[HW90_BLOCK_RF] = 0x3;
RT_TRACE(COMP_PHY, "%s(), CheckBlock: %d\n", __func__, CheckBlock);
for (i = 0; i < CheckTimes; i++) {
/* Write data to register and readback */
switch (CheckBlock) {
case HW90_BLOCK_MAC:
RT_TRACE(COMP_ERR,
"PHY_CheckBBRFOK(): Never Write 0x100 here!\n");
break;
case HW90_BLOCK_PHY0:
case HW90_BLOCK_PHY1:
write_nic_dword(dev, WriteAddr[CheckBlock],
WriteData[i]);
read_nic_dword(dev, WriteAddr[CheckBlock], ®);
break;
case HW90_BLOCK_RF:
WriteData[i] &= 0xfff;
rtl8192_phy_SetRFReg(dev, eRFPath,
WriteAddr[HW90_BLOCK_RF],
bMask12Bits, WriteData[i]);
/* TODO: we should not delay for such a long time.
Ask SD3 */
usleep_range(1000, 1000);
reg = rtl8192_phy_QueryRFReg(dev, eRFPath,
WriteAddr[HW90_BLOCK_RF],
bMask12Bits);
usleep_range(1000, 1000);
break;
default:
ret = 1;
break;
}
/* Check whether readback data is correct */
if (reg != WriteData[i]) {
RT_TRACE((COMP_PHY|COMP_ERR),
"error reg: %x, WriteData: %x\n",
reg, WriteData[i]);
ret = 1;
break;
}
}
return ret;
}
/******************************************************************************
* function: This function initializes BB&RF
* input: net_device *dev
* output: none
* return: none
* notice: Initialization value may change all the time, so please make
* sure it has been synced with the newest.
******************************************************************************/
static void rtl8192_BB_Config_ParaFile(struct net_device *dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
u8 reg_u8 = 0, eCheckItem = 0, status = 0;
u32 reg_u32 = 0;
/**************************************
* <1> Initialize BaseBand
*************************************/
/* --set BB Global Reset-- */
read_nic_byte(dev, BB_GLOBAL_RESET, ®_u8);
write_nic_byte(dev, BB_GLOBAL_RESET, (reg_u8|BB_GLOBAL_RESET_BIT));
mdelay(50);
/* ---set BB reset Active--- */
read_nic_dword(dev, CPU_GEN, ®_u32);
write_nic_dword(dev, CPU_GEN, (reg_u32&(~CPU_GEN_BB_RST)));
/* ----Ckeck FPGAPHY0 and PHY1 board is OK---- */
/* TODO: this function should be removed on ASIC */
for (eCheckItem = (HW90_BLOCK_E)HW90_BLOCK_PHY0;
eCheckItem <= HW90_BLOCK_PHY1; eCheckItem++) {
/* don't care RF path */
status = rtl8192_phy_checkBBAndRF(dev, (HW90_BLOCK_E)eCheckItem,
(RF90_RADIO_PATH_E)0);
if (status != 0) {
RT_TRACE((COMP_ERR | COMP_PHY),
"PHY_RF8256_Config(): Check PHY%d Fail!!\n",
eCheckItem-1);
return;
}
}
/* ---- Set CCK and OFDM Block "OFF"---- */
rtl8192_setBBreg(dev, rFPGA0_RFMOD, bCCKEn|bOFDMEn, 0x0);
/* ----BB Register Initilazation---- */
/* ==m==>Set PHY REG From Header<==m== */
rtl8192_phyConfigBB(dev, BaseBand_Config_PHY_REG);
/* ----Set BB reset de-Active---- */
read_nic_dword(dev, CPU_GEN, ®_u32);
write_nic_dword(dev, CPU_GEN, (reg_u32|CPU_GEN_BB_RST));
/* ----BB AGC table Initialization---- */
/* ==m==>Set PHY REG From Header<==m== */
rtl8192_phyConfigBB(dev, BaseBand_Config_AGC_TAB);
/* ----Enable XSTAL ---- */
write_nic_byte_E(dev, 0x5e, 0x00);
if (priv->card_8192_version == (u8)VERSION_819xU_A) {
/* Antenna gain offset from B/C/D to A */
reg_u32 = priv->AntennaTxPwDiff[1]<<4 |
priv->AntennaTxPwDiff[0];
rtl8192_setBBreg(dev, rFPGA0_TxGainStage, (bXBTxAGC|bXCTxAGC),
reg_u32);
/* XSTALLCap */
reg_u32 = priv->CrystalCap & 0xf;
rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1, bXtalCap,
reg_u32);
}
/* Check if the CCK HighPower is turned ON.
This is used to calculate PWDB. */
priv->bCckHighPower = (u8)rtl8192_QueryBBReg(dev,
rFPGA0_XA_HSSIParameter2,
0x200);
}
/******************************************************************************
* function: This function initializes BB&RF
* input: net_device *dev
* output: none
* return: none
* notice: Initialization value may change all the time, so please make
* sure it has been synced with the newest.
*****************************************************************************/
void rtl8192_BBConfig(struct net_device *dev)
{
rtl8192_InitBBRFRegDef(dev);
/* config BB&RF. As hardCode based initialization has not been well
* implemented, so use file first.
* FIXME: should implement it for hardcode? */
rtl8192_BB_Config_ParaFile(dev);
}
/******************************************************************************
* function: This function obtains the initialization value of Tx power Level
* offset
* input: net_device *dev
* output: none
* return: none
*****************************************************************************/
void rtl8192_phy_getTxPower(struct net_device *dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
u8 tmp;
read_nic_dword(dev, rTxAGC_Rate18_06,
&priv->MCSTxPowerLevelOriginalOffset[0]);
read_nic_dword(dev, rTxAGC_Rate54_24,
&priv->MCSTxPowerLevelOriginalOffset[1]);
read_nic_dword(dev, rTxAGC_Mcs03_Mcs00,
&priv->MCSTxPowerLevelOriginalOffset[2]);
read_nic_dword(dev, rTxAGC_Mcs07_Mcs04,
&priv->MCSTxPowerLevelOriginalOffset[3]);
read_nic_dword(dev, rTxAGC_Mcs11_Mcs08,
&priv->MCSTxPowerLevelOriginalOffset[4]);
read_nic_dword(dev, rTxAGC_Mcs15_Mcs12,
&priv->MCSTxPowerLevelOriginalOffset[5]);
/* Read rx initial gain */
read_nic_byte(dev, rOFDM0_XAAGCCore1, &priv->DefaultInitialGain[0]);
read_nic_byte(dev, rOFDM0_XBAGCCore1, &priv->DefaultInitialGain[1]);
read_nic_byte(dev, rOFDM0_XCAGCCore1, &priv->DefaultInitialGain[2]);
read_nic_byte(dev, rOFDM0_XDAGCCore1, &priv->DefaultInitialGain[3]);
RT_TRACE(COMP_INIT,
"Default initial gain (c50=0x%x, c58=0x%x, c60=0x%x, c68=0x%x)\n",
priv->DefaultInitialGain[0], priv->DefaultInitialGain[1],
priv->DefaultInitialGain[2], priv->DefaultInitialGain[3]);
/* Read framesync */
read_nic_byte(dev, rOFDM0_RxDetector3, &priv->framesync);
read_nic_byte(dev, rOFDM0_RxDetector2, &tmp);
priv->framesyncC34 = tmp;
RT_TRACE(COMP_INIT, "Default framesync (0x%x) = 0x%x\n",
rOFDM0_RxDetector3, priv->framesync);
/* Read SIFS (save the value read fome MACPHY_REG.txt) */
read_nic_word(dev, SIFS, &priv->SifsTime);
}
/******************************************************************************
* function: This function sets the initialization value of Tx power Level
* offset
* input: net_device *dev
* u8 channel
* output: none
* return: none
******************************************************************************/
void rtl8192_phy_setTxPower(struct net_device *dev, u8 channel)
{
struct r8192_priv *priv = ieee80211_priv(dev);
u8 powerlevel = priv->TxPowerLevelCCK[channel-1];
u8 powerlevelOFDM24G = priv->TxPowerLevelOFDM24G[channel-1];
switch (priv->rf_chip) {
case RF_8256:
/* need further implement */
PHY_SetRF8256CCKTxPower(dev, powerlevel);
PHY_SetRF8256OFDMTxPower(dev, powerlevelOFDM24G);
break;
default:
RT_TRACE((COMP_PHY|COMP_ERR),
"error RF chipID(8225 or 8258) in function %s()\n",
__func__);
break;
}
}
/******************************************************************************
* function: This function checks Rf chip to do RF config
* input: net_device *dev
* output: none
* return: only 8256 is supported
******************************************************************************/
void rtl8192_phy_RFConfig(struct net_device *dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
switch (priv->rf_chip) {
case RF_8256:
PHY_RF8256_Config(dev);
break;
default:
RT_TRACE(COMP_ERR, "error chip id\n");
break;
}
}
/******************************************************************************
* function: This function updates Initial gain
* input: net_device *dev
* output: none
* return: As Windows has not implemented this, wait for complement
******************************************************************************/
void rtl8192_phy_updateInitGain(struct net_device *dev)
{
}
/******************************************************************************
* function: This function read RF parameters from general head file,
* and do RF 3-wire
* input: net_device *dev
* RF90_RADIO_PATH_E eRFPath
* output: none
* return: return code show if RF configuration is successful(0:pass, 1:fail)
* notice: Delay may be required for RF configuration
*****************************************************************************/
u8 rtl8192_phy_ConfigRFWithHeaderFile(struct net_device *dev,
RF90_RADIO_PATH_E eRFPath)
{
int i;
switch (eRFPath) {
case RF90_PATH_A:
for (i = 0; i < RadioA_ArrayLength; i = i+2) {
if (rtl819XRadioA_Array[i] == 0xfe) {
mdelay(100);
continue;
}
rtl8192_phy_SetRFReg(dev, eRFPath,
rtl819XRadioA_Array[i],
bMask12Bits,
rtl819XRadioA_Array[i+1]);
mdelay(1);
}
break;
case RF90_PATH_B:
for (i = 0; i < RadioB_ArrayLength; i = i+2) {
if (rtl819XRadioB_Array[i] == 0xfe) {
mdelay(100);
continue;
}
rtl8192_phy_SetRFReg(dev, eRFPath,
rtl819XRadioB_Array[i],
bMask12Bits,
rtl819XRadioB_Array[i+1]);
mdelay(1);
}
break;
case RF90_PATH_C:
for (i = 0; i < RadioC_ArrayLength; i = i+2) {
if (rtl819XRadioC_Array[i] == 0xfe) {
mdelay(100);
continue;
}
rtl8192_phy_SetRFReg(dev, eRFPath,
rtl819XRadioC_Array[i],
bMask12Bits,
rtl819XRadioC_Array[i+1]);
mdelay(1);
}
break;
case RF90_PATH_D:
for (i = 0; i < RadioD_ArrayLength; i = i+2) {
if (rtl819XRadioD_Array[i] == 0xfe) {
mdelay(100);
continue;
}
rtl8192_phy_SetRFReg(dev, eRFPath,
rtl819XRadioD_Array[i],
bMask12Bits,
rtl819XRadioD_Array[i+1]);
mdelay(1);
}
break;
default:
break;
}
return 0;
}
/******************************************************************************
* function: This function sets Tx Power of the channel
* input: net_device *dev
* u8 channel
* output: none
* return: none
* notice:
******************************************************************************/
static void rtl8192_SetTxPowerLevel(struct net_device *dev, u8 channel)
{
struct r8192_priv *priv = ieee80211_priv(dev);
u8 powerlevel = priv->TxPowerLevelCCK[channel-1];
u8 powerlevelOFDM24G = priv->TxPowerLevelOFDM24G[channel-1];
switch (priv->rf_chip) {
case RF_8225:
#ifdef TO_DO_LIST
PHY_SetRF8225CckTxPower(Adapter, powerlevel);
PHY_SetRF8225OfdmTxPower(Adapter, powerlevelOFDM24G);
#endif
break;
case RF_8256:
PHY_SetRF8256CCKTxPower(dev, powerlevel);
PHY_SetRF8256OFDMTxPower(dev, powerlevelOFDM24G);
break;
case RF_8258:
break;
default:
RT_TRACE(COMP_ERR, "unknown rf chip ID in %s()\n", __func__);
break;
}
}
/******************************************************************************
* function: This function sets RF state on or off
* input: net_device *dev
* RT_RF_POWER_STATE eRFPowerState //Power State to set
* output: none
* return: none
* notice:
*****************************************************************************/
bool rtl8192_SetRFPowerState(struct net_device *dev,
RT_RF_POWER_STATE eRFPowerState)
{
bool bResult = true;
struct r8192_priv *priv = ieee80211_priv(dev);
if (eRFPowerState == priv->ieee80211->eRFPowerState)
return false;
if (priv->SetRFPowerStateInProgress)
return false;
priv->SetRFPowerStateInProgress = true;
switch (priv->rf_chip) {
case RF_8256:
switch (eRFPowerState) {
case eRfOn:
/* RF-A, RF-B */
/* enable RF-Chip A/B - 0x860[4] */
rtl8192_setBBreg(dev, rFPGA0_XA_RFInterfaceOE, BIT(4),
0x1);
/* analog to digital on - 0x88c[9:8] */
rtl8192_setBBreg(dev, rFPGA0_AnalogParameter4, 0x300,
0x3);
/* digital to analog on - 0x880[4:3] */
rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1, 0x18,
0x3);
/* rx antenna on - 0xc04[1:0] */
rtl8192_setBBreg(dev, rOFDM0_TRxPathEnable, 0x3, 0x3);
/* rx antenna on - 0xd04[1:0] */
rtl8192_setBBreg(dev, rOFDM1_TRxPathEnable, 0x3, 0x3);
/* analog to digital part2 on - 0x880[6:5] */
rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1, 0x60,
0x3);
break;
case eRfSleep:
break;
case eRfOff:
/* RF-A, RF-B */
/* disable RF-Chip A/B - 0x860[4] */
rtl8192_setBBreg(dev, rFPGA0_XA_RFInterfaceOE, BIT(4),
0x0);
/* analog to digital off, for power save */
rtl8192_setBBreg(dev, rFPGA0_AnalogParameter4, 0xf00,
0x0); /* 0x88c[11:8] */
/* digital to analog off, for power save - 0x880[4:3] */
rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1, 0x18,
0x0);
/* rx antenna off - 0xc04[3:0] */
rtl8192_setBBreg(dev, rOFDM0_TRxPathEnable, 0xf, 0x0);
/* rx antenna off - 0xd04[3:0] */
rtl8192_setBBreg(dev, rOFDM1_TRxPathEnable, 0xf, 0x0);
/* analog to digital part2 off, for power save */
rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1, 0x60,
0x0); /* 0x880[6:5] */
break;
default:
bResult = false;
RT_TRACE(COMP_ERR, "%s(): unknown state to set: 0x%X\n",
__func__, eRFPowerState);
break;
}
break;
default:
RT_TRACE(COMP_ERR, "Not support rf_chip(%x)\n", priv->rf_chip);
break;
}
#ifdef TO_DO_LIST
if (bResult) {
/* Update current RF state variable. */
pHalData->eRFPowerState = eRFPowerState;
switch (pHalData->RFChipID) {
case RF_8256:
switch (pHalData->eRFPowerState) {
case eRfOff:
/* If Rf off reason is from IPS,
LED should blink with no link */
if (pMgntInfo->RfOffReason == RF_CHANGE_BY_IPS)
Adapter->HalFunc.LedControlHandler(Adapter, LED_CTL_NO_LINK);
else
/* Turn off LED if RF is not ON. */
Adapter->HalFunc.LedControlHandler(Adapter, LED_CTL_POWER_OFF);
break;
case eRfOn:
/* Turn on RF we are still linked, which might
happen when we quickly turn off and on HW RF.
*/
if (pMgntInfo->bMediaConnect)
Adapter->HalFunc.LedControlHandler(Adapter, LED_CTL_LINK);
else
/* Turn off LED if RF is not ON. */
Adapter->HalFunc.LedControlHandler(Adapter, LED_CTL_NO_LINK);
break;
default:
break;
}
break;
default:
RT_TRACE(COMP_RF, DBG_LOUD, "%s(): Unknown RF type\n",
__func__);
break;
}
}
#endif
priv->SetRFPowerStateInProgress = false;
return bResult;
}
/******************************************************************************
* function: This function sets command table variable (struct SwChnlCmd).
* input: SwChnlCmd *CmdTable //table to be set
* u32 CmdTableIdx //variable index in table to be set
* u32 CmdTableSz //table size
* SwChnlCmdID CmdID //command ID to set
* u32 Para1
* u32 Para2
* u32 msDelay
* output:
* return: true if finished, false otherwise
* notice:
******************************************************************************/
static u8 rtl8192_phy_SetSwChnlCmdArray(SwChnlCmd *CmdTable, u32 CmdTableIdx,
u32 CmdTableSz, SwChnlCmdID CmdID,
u32 Para1, u32 Para2, u32 msDelay)
{
SwChnlCmd *pCmd;
if (CmdTable == NULL) {
RT_TRACE(COMP_ERR, "%s(): CmdTable cannot be NULL\n", __func__);
return false;
}
if (CmdTableIdx >= CmdTableSz) {
RT_TRACE(COMP_ERR, "%s(): Access invalid index, please check size of the table, CmdTableIdx:%d, CmdTableSz:%d\n",
__func__, CmdTableIdx, CmdTableSz);
return false;
}
pCmd = CmdTable + CmdTableIdx;
pCmd->CmdID = CmdID;
pCmd->Para1 = Para1;
pCmd->Para2 = Para2;
pCmd->msDelay = msDelay;
return true;
}
/******************************************************************************
* function: This function sets channel step by step
* input: net_device *dev
* u8 channel
* u8 *stage //3 stages
* u8 *step
* u32 *delay //whether need to delay
* output: store new stage, step and delay for next step
* (combine with function above)
* return: true if finished, false otherwise
* notice: Wait for simpler function to replace it
*****************************************************************************/
static u8 rtl8192_phy_SwChnlStepByStep(struct net_device *dev, u8 channel,
u8 *stage, u8 *step, u32 *delay)
{
struct r8192_priv *priv = ieee80211_priv(dev);
SwChnlCmd PreCommonCmd[MAX_PRECMD_CNT];
u32 PreCommonCmdCnt;
SwChnlCmd PostCommonCmd[MAX_POSTCMD_CNT];
u32 PostCommonCmdCnt;
SwChnlCmd RfDependCmd[MAX_RFDEPENDCMD_CNT];
u32 RfDependCmdCnt;
SwChnlCmd *CurrentCmd = NULL;
u8 eRFPath;
RT_TRACE(COMP_CH, "%s() stage: %d, step: %d, channel: %d\n",
__func__, *stage, *step, channel);
if (!IsLegalChannel(priv->ieee80211, channel)) {
RT_TRACE(COMP_ERR, "set to illegal channel: %d\n", channel);
/* return true to tell upper caller function this channel
setting is finished! Or it will in while loop. */
return true;
}
/* FIXME: need to check whether channel is legal or not here */
/* <1> Fill up pre common command. */
PreCommonCmdCnt = 0;
rtl8192_phy_SetSwChnlCmdArray(PreCommonCmd, PreCommonCmdCnt++,
MAX_PRECMD_CNT, CmdID_SetTxPowerLevel,
0, 0, 0);
rtl8192_phy_SetSwChnlCmdArray(PreCommonCmd, PreCommonCmdCnt++,
MAX_PRECMD_CNT, CmdID_End, 0, 0, 0);
/* <2> Fill up post common command. */
PostCommonCmdCnt = 0;
rtl8192_phy_SetSwChnlCmdArray(PostCommonCmd, PostCommonCmdCnt++,
MAX_POSTCMD_CNT, CmdID_End, 0, 0, 0);
/* <3> Fill up RF dependent command. */
RfDependCmdCnt = 0;
switch (priv->rf_chip) {
case RF_8225:
if (!(channel >= 1 && channel <= 14)) {
RT_TRACE(COMP_ERR,
"illegal channel for Zebra 8225: %d\n",
channel);
return true;
}
rtl8192_phy_SetSwChnlCmdArray(RfDependCmd, RfDependCmdCnt++,
MAX_RFDEPENDCMD_CNT,
CmdID_RF_WriteReg,
rZebra1_Channel,
RF_CHANNEL_TABLE_ZEBRA[channel],
10);
rtl8192_phy_SetSwChnlCmdArray(RfDependCmd, RfDependCmdCnt++,
MAX_RFDEPENDCMD_CNT,
CmdID_End, 0, 0, 0);
break;
case RF_8256:
/* TEST!! This is not the table for 8256!! */
if (!(channel >= 1 && channel <= 14)) {
RT_TRACE(COMP_ERR,
"illegal channel for Zebra 8256: %d\n",
channel);
return true;
}
rtl8192_phy_SetSwChnlCmdArray(RfDependCmd, RfDependCmdCnt++,
MAX_RFDEPENDCMD_CNT,
CmdID_RF_WriteReg,
rZebra1_Channel, channel, 10);
rtl8192_phy_SetSwChnlCmdArray(RfDependCmd, RfDependCmdCnt++,
MAX_RFDEPENDCMD_CNT,
CmdID_End, 0, 0, 0);
break;
case RF_8258:
break;
default:
RT_TRACE(COMP_ERR, "Unknown RFChipID: %d\n", priv->rf_chip);
return true;
}
do {
switch (*stage) {
case 0:
CurrentCmd = &PreCommonCmd[*step];
break;
case 1:
CurrentCmd = &RfDependCmd[*step];
break;
case 2:
CurrentCmd = &PostCommonCmd[*step];
break;
}
if (CurrentCmd->CmdID == CmdID_End) {
if ((*stage) == 2) {
(*delay) = CurrentCmd->msDelay;
return true;
}
(*stage)++;
(*step) = 0;
continue;
}
switch (CurrentCmd->CmdID) {
case CmdID_SetTxPowerLevel:
if (priv->card_8192_version == (u8)VERSION_819xU_A)
/* consider it later! */
rtl8192_SetTxPowerLevel(dev, channel);
break;
case CmdID_WritePortUlong:
write_nic_dword(dev, CurrentCmd->Para1,
CurrentCmd->Para2);
break;
case CmdID_WritePortUshort:
write_nic_word(dev, CurrentCmd->Para1,
(u16)CurrentCmd->Para2);
break;
case CmdID_WritePortUchar:
write_nic_byte(dev, CurrentCmd->Para1,
(u8)CurrentCmd->Para2);
break;
case CmdID_RF_WriteReg:
for (eRFPath = 0; eRFPath < RF90_PATH_MAX; eRFPath++) {
rtl8192_phy_SetRFReg(dev,
(RF90_RADIO_PATH_E)eRFPath,
CurrentCmd->Para1,
bZebra1_ChannelNum,
CurrentCmd->Para2);
}
break;
default:
break;
}
break;
} while (true);
(*delay) = CurrentCmd->msDelay;
(*step)++;
return false;
}
/******************************************************************************
* function: This function does actually set channel work
* input: net_device *dev
* u8 channel
* output: none
* return: none
* notice: We should not call this function directly
*****************************************************************************/
static void rtl8192_phy_FinishSwChnlNow(struct net_device *dev, u8 channel)
{
struct r8192_priv *priv = ieee80211_priv(dev);
u32 delay = 0;
while (!rtl8192_phy_SwChnlStepByStep(dev, channel, &priv->SwChnlStage,
&priv->SwChnlStep, &delay)) {
if (!priv->up)
break;
}
}
/******************************************************************************
* function: Callback routine of the work item for switch channel.
* input: net_device *dev
*
* output: none
* return: none
*****************************************************************************/
void rtl8192_SwChnl_WorkItem(struct net_device *dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
RT_TRACE(COMP_CH, "==> SwChnlCallback819xUsbWorkItem(), chan:%d\n",
priv->chan);
rtl8192_phy_FinishSwChnlNow(dev, priv->chan);
RT_TRACE(COMP_CH, "<== SwChnlCallback819xUsbWorkItem()\n");
}
/******************************************************************************
* function: This function scheduled actual work item to set channel
* input: net_device *dev
* u8 channel //channel to set
* output: none
* return: return code show if workitem is scheduled (1:pass, 0:fail)
* notice: Delay may be required for RF configuration
******************************************************************************/
u8 rtl8192_phy_SwChnl(struct net_device *dev, u8 channel)
{
struct r8192_priv *priv = ieee80211_priv(dev);
RT_TRACE(COMP_CH, "%s(), SwChnlInProgress: %d\n", __func__,
priv->SwChnlInProgress);
if (!priv->up)
return false;
if (priv->SwChnlInProgress)
return false;
/* -------------------------------------------- */
switch (priv->ieee80211->mode) {
case WIRELESS_MODE_A:
case WIRELESS_MODE_N_5G:
if (channel <= 14) {
RT_TRACE(COMP_ERR, "WIRELESS_MODE_A but channel<=14\n");
return false;
}
break;
case WIRELESS_MODE_B:
if (channel > 14) {
RT_TRACE(COMP_ERR, "WIRELESS_MODE_B but channel>14\n");
return false;
}
break;
case WIRELESS_MODE_G:
case WIRELESS_MODE_N_24G:
if (channel > 14) {
RT_TRACE(COMP_ERR, "WIRELESS_MODE_G but channel>14\n");
return false;
}
break;
}
/* -------------------------------------------- */
priv->SwChnlInProgress = true;
if (channel == 0)
channel = 1;
priv->chan = channel;
priv->SwChnlStage = 0;
priv->SwChnlStep = 0;
if (priv->up)
rtl8192_SwChnl_WorkItem(dev);
priv->SwChnlInProgress = false;
return true;
}
/******************************************************************************
* function: Callback routine of the work item for set bandwidth mode.
* input: net_device *dev
* output: none
* return: none
* notice: I doubt whether SetBWModeInProgress flag is necessary as we can
* test whether current work in the queue or not.//do I?
*****************************************************************************/
void rtl8192_SetBWModeWorkItem(struct net_device *dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
u8 regBwOpMode;
RT_TRACE(COMP_SWBW, "%s() Switch to %s bandwidth\n", __func__,
priv->CurrentChannelBW == HT_CHANNEL_WIDTH_20?"20MHz":"40MHz");
if (priv->rf_chip == RF_PSEUDO_11N) {
priv->SetBWModeInProgress = false;
return;
}
/* <1> Set MAC register */
read_nic_byte(dev, BW_OPMODE, ®BwOpMode);
switch (priv->CurrentChannelBW) {
case HT_CHANNEL_WIDTH_20:
regBwOpMode |= BW_OPMODE_20MHZ;
/* We have not verify whether this register works */
write_nic_byte(dev, BW_OPMODE, regBwOpMode);
break;
case HT_CHANNEL_WIDTH_20_40:
regBwOpMode &= ~BW_OPMODE_20MHZ;
/* We have not verify whether this register works */
write_nic_byte(dev, BW_OPMODE, regBwOpMode);
break;
default:
RT_TRACE(COMP_ERR,
"SetChannelBandwidth819xUsb(): unknown Bandwidth: %#X\n",
priv->CurrentChannelBW);
break;
}
/* <2> Set PHY related register */
switch (priv->CurrentChannelBW) {
case HT_CHANNEL_WIDTH_20:
rtl8192_setBBreg(dev, rFPGA0_RFMOD, bRFMOD, 0x0);
rtl8192_setBBreg(dev, rFPGA1_RFMOD, bRFMOD, 0x0);
rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1,
0x00100000, 1);
/* Correct the tx power for CCK rate in 20M. */
priv->cck_present_attentuation =
priv->cck_present_attentuation_20Mdefault +
priv->cck_present_attentuation_difference;
if (priv->cck_present_attentuation > 22)
priv->cck_present_attentuation = 22;
if (priv->cck_present_attentuation < 0)
priv->cck_present_attentuation = 0;
RT_TRACE(COMP_INIT,
"20M, pHalData->CCKPresentAttentuation = %d\n",
priv->cck_present_attentuation);
if (priv->chan == 14 && !priv->bcck_in_ch14) {
priv->bcck_in_ch14 = true;
dm_cck_txpower_adjust(dev, priv->bcck_in_ch14);
} else if (priv->chan != 14 && priv->bcck_in_ch14) {
priv->bcck_in_ch14 = false;
dm_cck_txpower_adjust(dev, priv->bcck_in_ch14);
} else {
dm_cck_txpower_adjust(dev, priv->bcck_in_ch14);
}
break;
case HT_CHANNEL_WIDTH_20_40:
rtl8192_setBBreg(dev, rFPGA0_RFMOD, bRFMOD, 0x1);
rtl8192_setBBreg(dev, rFPGA1_RFMOD, bRFMOD, 0x1);
rtl8192_setBBreg(dev, rCCK0_System, bCCKSideBand,
priv->nCur40MhzPrimeSC>>1);
rtl8192_setBBreg(dev, rFPGA0_AnalogParameter1, 0x00100000, 0);
rtl8192_setBBreg(dev, rOFDM1_LSTF, 0xC00,
priv->nCur40MhzPrimeSC);
priv->cck_present_attentuation =
priv->cck_present_attentuation_40Mdefault +
priv->cck_present_attentuation_difference;
if (priv->cck_present_attentuation > 22)
priv->cck_present_attentuation = 22;
if (priv->cck_present_attentuation < 0)
priv->cck_present_attentuation = 0;
RT_TRACE(COMP_INIT,
"40M, pHalData->CCKPresentAttentuation = %d\n",
priv->cck_present_attentuation);
if (priv->chan == 14 && !priv->bcck_in_ch14) {
priv->bcck_in_ch14 = true;
dm_cck_txpower_adjust(dev, priv->bcck_in_ch14);
} else if (priv->chan != 14 && priv->bcck_in_ch14) {
priv->bcck_in_ch14 = false;
dm_cck_txpower_adjust(dev, priv->bcck_in_ch14);
} else {
dm_cck_txpower_adjust(dev, priv->bcck_in_ch14);
}
break;
default:
RT_TRACE(COMP_ERR,
"SetChannelBandwidth819xUsb(): unknown Bandwidth: %#X\n",
priv->CurrentChannelBW);
break;
}
/* Skip over setting of J-mode in BB register here.
Default value is "None J mode". */
/* <3> Set RF related register */
switch (priv->rf_chip) {
case RF_8225:
#ifdef TO_DO_LIST
PHY_SetRF8225Bandwidth(Adapter, pHalData->CurrentChannelBW);
#endif
break;
case RF_8256:
PHY_SetRF8256Bandwidth(dev, priv->CurrentChannelBW);
break;
case RF_8258:
break;
case RF_PSEUDO_11N:
break;
default:
RT_TRACE(COMP_ERR, "Unknown RFChipID: %d\n", priv->rf_chip);
break;
}
priv->SetBWModeInProgress = false;
RT_TRACE(COMP_SWBW, "<==SetBWMode819xUsb(), %d\n",
atomic_read(&priv->ieee80211->atm_swbw));
}
/******************************************************************************
* function: This function schedules bandwidth switch work.
* input: struct net_deviceq *dev
* HT_CHANNEL_WIDTH bandwidth //20M or 40M
* HT_EXTCHNL_OFFSET offset //Upper, Lower, or Don't care
* output: none
* return: none
* notice: I doubt whether SetBWModeInProgress flag is necessary as we can
* test whether current work in the queue or not.//do I?
*****************************************************************************/
void rtl8192_SetBWMode(struct net_device *dev, HT_CHANNEL_WIDTH bandwidth,
HT_EXTCHNL_OFFSET offset)
{
struct r8192_priv *priv = ieee80211_priv(dev);
if (priv->SetBWModeInProgress)
return;
priv->SetBWModeInProgress = true;
priv->CurrentChannelBW = bandwidth;
if (offset == HT_EXTCHNL_OFFSET_LOWER)
priv->nCur40MhzPrimeSC = HAL_PRIME_CHNL_OFFSET_UPPER;
else if (offset == HT_EXTCHNL_OFFSET_UPPER)
priv->nCur40MhzPrimeSC = HAL_PRIME_CHNL_OFFSET_LOWER;
else
priv->nCur40MhzPrimeSC = HAL_PRIME_CHNL_OFFSET_DONT_CARE;
rtl8192_SetBWModeWorkItem(dev);
}
void InitialGain819xUsb(struct net_device *dev, u8 Operation)
{
struct r8192_priv *priv = ieee80211_priv(dev);
priv->InitialGainOperateType = Operation;
if (priv->up)
queue_delayed_work(priv->priv_wq, &priv->initialgain_operate_wq, 0);
}
void InitialGainOperateWorkItemCallBack(struct work_struct *work)
{
struct delayed_work *dwork = container_of(work, struct delayed_work,
work);
struct r8192_priv *priv = container_of(dwork, struct r8192_priv,
initialgain_operate_wq);
struct net_device *dev = priv->ieee80211->dev;
#define SCAN_RX_INITIAL_GAIN 0x17
#define POWER_DETECTION_TH 0x08
u32 bitmask;
u8 initial_gain;
u8 Operation;
Operation = priv->InitialGainOperateType;
switch (Operation) {
case IG_Backup:
RT_TRACE(COMP_SCAN, "IG_Backup, backup the initial gain.\n");
initial_gain = SCAN_RX_INITIAL_GAIN;
bitmask = bMaskByte0;
if (dm_digtable.dig_algorithm == DIG_ALGO_BY_FALSE_ALARM)
/* FW DIG OFF */
rtl8192_setBBreg(dev, UFWP, bMaskByte1, 0x8);
priv->initgain_backup.xaagccore1 =
(u8)rtl8192_QueryBBReg(dev, rOFDM0_XAAGCCore1, bitmask);
priv->initgain_backup.xbagccore1 =
(u8)rtl8192_QueryBBReg(dev, rOFDM0_XBAGCCore1, bitmask);
priv->initgain_backup.xcagccore1 =
(u8)rtl8192_QueryBBReg(dev, rOFDM0_XCAGCCore1, bitmask);
priv->initgain_backup.xdagccore1 =
(u8)rtl8192_QueryBBReg(dev, rOFDM0_XDAGCCore1, bitmask);
bitmask = bMaskByte2;
priv->initgain_backup.cca =
(u8)rtl8192_QueryBBReg(dev, rCCK0_CCA, bitmask);
RT_TRACE(COMP_SCAN, "Scan InitialGainBackup 0xc50 is %x\n",
priv->initgain_backup.xaagccore1);
RT_TRACE(COMP_SCAN, "Scan InitialGainBackup 0xc58 is %x\n",
priv->initgain_backup.xbagccore1);
RT_TRACE(COMP_SCAN, "Scan InitialGainBackup 0xc60 is %x\n",
priv->initgain_backup.xcagccore1);
RT_TRACE(COMP_SCAN, "Scan InitialGainBackup 0xc68 is %x\n",
priv->initgain_backup.xdagccore1);
RT_TRACE(COMP_SCAN, "Scan InitialGainBackup 0xa0a is %x\n",
priv->initgain_backup.cca);
RT_TRACE(COMP_SCAN, "Write scan initial gain = 0x%x\n",
initial_gain);
write_nic_byte(dev, rOFDM0_XAAGCCore1, initial_gain);
write_nic_byte(dev, rOFDM0_XBAGCCore1, initial_gain);
write_nic_byte(dev, rOFDM0_XCAGCCore1, initial_gain);
write_nic_byte(dev, rOFDM0_XDAGCCore1, initial_gain);
RT_TRACE(COMP_SCAN, "Write scan 0xa0a = 0x%x\n",
POWER_DETECTION_TH);
write_nic_byte(dev, 0xa0a, POWER_DETECTION_TH);
break;
case IG_Restore:
RT_TRACE(COMP_SCAN, "IG_Restore, restore the initial gain.\n");
bitmask = 0x7f; /* Bit0 ~ Bit6 */
if (dm_digtable.dig_algorithm == DIG_ALGO_BY_FALSE_ALARM)
/* FW DIG OFF */
rtl8192_setBBreg(dev, UFWP, bMaskByte1, 0x8);
rtl8192_setBBreg(dev, rOFDM0_XAAGCCore1, bitmask,
(u32)priv->initgain_backup.xaagccore1);
rtl8192_setBBreg(dev, rOFDM0_XBAGCCore1, bitmask,
(u32)priv->initgain_backup.xbagccore1);
rtl8192_setBBreg(dev, rOFDM0_XCAGCCore1, bitmask,
(u32)priv->initgain_backup.xcagccore1);
rtl8192_setBBreg(dev, rOFDM0_XDAGCCore1, bitmask,
(u32)priv->initgain_backup.xdagccore1);
bitmask = bMaskByte2;
rtl8192_setBBreg(dev, rCCK0_CCA, bitmask,
(u32)priv->initgain_backup.cca);
RT_TRACE(COMP_SCAN, "Scan BBInitialGainRestore 0xc50 is %x\n",
priv->initgain_backup.xaagccore1);
RT_TRACE(COMP_SCAN, "Scan BBInitialGainRestore 0xc58 is %x\n",
priv->initgain_backup.xbagccore1);
RT_TRACE(COMP_SCAN, "Scan BBInitialGainRestore 0xc60 is %x\n",
priv->initgain_backup.xcagccore1);
RT_TRACE(COMP_SCAN, "Scan BBInitialGainRestore 0xc68 is %x\n",
priv->initgain_backup.xdagccore1);
RT_TRACE(COMP_SCAN, "Scan BBInitialGainRestore 0xa0a is %x\n",
priv->initgain_backup.cca);
rtl8192_phy_setTxPower(dev, priv->ieee80211->current_network.channel);
if (dm_digtable.dig_algorithm == DIG_ALGO_BY_FALSE_ALARM)
/* FW DIG ON */
rtl8192_setBBreg(dev, UFWP, bMaskByte1, 0x1);
break;
default:
RT_TRACE(COMP_SCAN, "Unknown IG Operation.\n");
break;
}
}