- 根目录:
- drivers
- net
- dsa
- bcm_sf2_regs.h
/*
* Broadcom Starfighter 2 switch register defines
*
* Copyright (C) 2014, Broadcom Corporation
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
#ifndef __BCM_SF2_REGS_H
#define __BCM_SF2_REGS_H
/* Register set relative to 'REG' */
#define REG_SWITCH_CNTRL 0x00
#define MDIO_MASTER_SEL (1 << 0)
#define REG_SWITCH_STATUS 0x04
#define REG_DIR_DATA_WRITE 0x08
#define REG_DIR_DATA_READ 0x0C
#define REG_SWITCH_REVISION 0x18
#define SF2_REV_MASK 0xffff
#define SWITCH_TOP_REV_SHIFT 16
#define SWITCH_TOP_REV_MASK 0xffff
#define REG_PHY_REVISION 0x1C
#define PHY_REVISION_MASK 0xffff
#define REG_SPHY_CNTRL 0x2C
#define IDDQ_BIAS (1 << 0)
#define EXT_PWR_DOWN (1 << 1)
#define FORCE_DLL_EN (1 << 2)
#define IDDQ_GLOBAL_PWR (1 << 3)
#define CK25_DIS (1 << 4)
#define PHY_RESET (1 << 5)
#define PHY_PHYAD_SHIFT 8
#define PHY_PHYAD_MASK 0x1F
#define REG_RGMII_0_BASE 0x34
#define REG_RGMII_CNTRL 0x00
#define REG_RGMII_IB_STATUS 0x04
#define REG_RGMII_RX_CLOCK_DELAY_CNTRL 0x08
#define REG_RGMII_CNTRL_SIZE 0x0C
#define REG_RGMII_CNTRL_P(x) (REG_RGMII_0_BASE + \
((x) * REG_RGMII_CNTRL_SIZE))
/* Relative to REG_RGMII_CNTRL */
#define RGMII_MODE_EN (1 << 0)
#define ID_MODE_DIS (1 << 1)
#define PORT_MODE_SHIFT 2
#define INT_EPHY (0 << PORT_MODE_SHIFT)
#define INT_GPHY (1 << PORT_MODE_SHIFT)
#define EXT_EPHY (2 << PORT_MODE_SHIFT)
#define EXT_GPHY (3 << PORT_MODE_SHIFT)
#define EXT_REVMII (4 << PORT_MODE_SHIFT)
#define PORT_MODE_MASK 0x7
#define RVMII_REF_SEL (1 << 5)
#define RX_PAUSE_EN (1 << 6)
#define TX_PAUSE_EN (1 << 7)
#define TX_CLK_STOP_EN (1 << 8)
#define LPI_COUNT_SHIFT 9
#define LPI_COUNT_MASK 0x3F
#define REG_LED_CNTRL_BASE 0x90
#define REG_LED_CNTRL(x) (REG_LED_CNTRL_BASE + (x) * 4)
#define SPDLNK_SRC_SEL (1 << 24)
/* Register set relative to 'INTRL2_0' and 'INTRL2_1' */
#define INTRL2_CPU_STATUS 0x00
#define INTRL2_CPU_SET 0x04
#define INTRL2_CPU_CLEAR 0x08
#define INTRL2_CPU_MASK_STATUS 0x0c
#define INTRL2_CPU_MASK_SET 0x10
#define INTRL2_CPU_MASK_CLEAR 0x14
/* Shared INTRL2_0 and INTRL2_ interrupt sources macros */
#define P_LINK_UP_IRQ(x) (1 << (0 + (x)))
#define P_LINK_DOWN_IRQ(x) (1 << (1 + (x)))
#define P_ENERGY_ON_IRQ(x) (1 << (2 + (x)))
#define P_ENERGY_OFF_IRQ(x) (1 << (3 + (x)))
#define P_GPHY_IRQ(x) (1 << (4 + (x)))
#define P_NUM_IRQ 5
#define P_IRQ_MASK(x) (P_LINK_UP_IRQ((x)) | \
P_LINK_DOWN_IRQ((x)) | \
P_ENERGY_ON_IRQ((x)) | \
P_ENERGY_OFF_IRQ((x)) | \
P_GPHY_IRQ((x)))
/* INTRL2_0 interrupt sources */
#define P0_IRQ_OFF 0
#define MEM_DOUBLE_IRQ (1 << 5)
#define EEE_LPI_IRQ (1 << 6)
#define P5_CPU_WAKE_IRQ (1 << 7)
#define P8_CPU_WAKE_IRQ (1 << 8)
#define P7_CPU_WAKE_IRQ (1 << 9)
#define IEEE1588_IRQ (1 << 10)
#define MDIO_ERR_IRQ (1 << 11)
#define MDIO_DONE_IRQ (1 << 12)
#define GISB_ERR_IRQ (1 << 13)
#define UBUS_ERR_IRQ (1 << 14)
#define FAILOVER_ON_IRQ (1 << 15)
#define FAILOVER_OFF_IRQ (1 << 16)
#define TCAM_SOFT_ERR_IRQ (1 << 17)
/* INTRL2_1 interrupt sources */
#define P7_IRQ_OFF 0
#define P_IRQ_OFF(x) ((6 - (x)) * P_NUM_IRQ)
/* Register set relative to 'CORE' */
#define CORE_G_PCTL_PORT0 0x00000
#define CORE_G_PCTL_PORT(x) (CORE_G_PCTL_PORT0 + (x * 0x4))
#define CORE_IMP_CTL 0x00020
#define RX_DIS (1 << 0)
#define TX_DIS (1 << 1)
#define RX_BCST_EN (1 << 2)
#define RX_MCST_EN (1 << 3)
#define RX_UCST_EN (1 << 4)
#define G_MISTP_STATE_SHIFT 5
#define G_MISTP_NO_STP (0 << G_MISTP_STATE_SHIFT)
#define G_MISTP_DIS_STATE (1 << G_MISTP_STATE_SHIFT)
#define G_MISTP_BLOCK_STATE (2 << G_MISTP_STATE_SHIFT)
#define G_MISTP_LISTEN_STATE (3 << G_MISTP_STATE_SHIFT)
#define G_MISTP_LEARN_STATE (4 << G_MISTP_STATE_SHIFT)
#define G_MISTP_FWD_STATE (5 << G_MISTP_STATE_SHIFT)
#define G_MISTP_STATE_MASK 0x7
#define CORE_SWMODE 0x0002c
#define SW_FWDG_MODE (1 << 0)
#define SW_FWDG_EN (1 << 1)
#define RTRY_LMT_DIS (1 << 2)
#define CORE_STS_OVERRIDE_IMP 0x00038
#define GMII_SPEED_UP_2G (1 << 6)
#define MII_SW_OR (1 << 7)
#define CORE_NEW_CTRL 0x00084
#define IP_MC (1 << 0)
#define OUTRANGEERR_DISCARD (1 << 1)
#define INRANGEERR_DISCARD (1 << 2)
#define CABLE_DIAG_LEN (1 << 3)
#define OVERRIDE_AUTO_PD_WAR (1 << 4)
#define EN_AUTO_PD_WAR (1 << 5)
#define UC_FWD_EN (1 << 6)
#define MC_FWD_EN (1 << 7)
#define CORE_SWITCH_CTRL 0x00088
#define MII_DUMB_FWDG_EN (1 << 6)
#define CORE_SFT_LRN_CTRL 0x000f8
#define SW_LEARN_CNTL(x) (1 << (x))
#define CORE_STS_OVERRIDE_GMIIP_PORT(x) (0x160 + (x) * 4)
#define LINK_STS (1 << 0)
#define DUPLX_MODE (1 << 1)
#define SPEED_SHIFT 2
#define SPEED_MASK 0x3
#define RXFLOW_CNTL (1 << 4)
#define TXFLOW_CNTL (1 << 5)
#define SW_OVERRIDE (1 << 6)
#define CORE_WATCHDOG_CTRL 0x001e4
#define SOFTWARE_RESET (1 << 7)
#define EN_CHIP_RST (1 << 6)
#define EN_SW_RESET (1 << 4)
#define CORE_FAST_AGE_CTRL 0x00220
#define EN_FAST_AGE_STATIC (1 << 0)
#define EN_AGE_DYNAMIC (1 << 1)
#define EN_AGE_PORT (1 << 2)
#define EN_AGE_VLAN (1 << 3)
#define EN_AGE_SPT (1 << 4)
#define EN_AGE_MCAST (1 << 5)
#define FAST_AGE_STR_DONE (1 << 7)
#define CORE_FAST_AGE_PORT 0x00224
#define AGE_PORT_MASK 0xf
#define CORE_FAST_AGE_VID 0x00228
#define AGE_VID_MASK 0x3fff
#define CORE_LNKSTS 0x00400
#define LNK_STS_MASK 0x1ff
#define CORE_SPDSTS 0x00410
#define SPDSTS_10 0
#define SPDSTS_100 1
#define SPDSTS_1000 2
#define SPDSTS_SHIFT 2
#define SPDSTS_MASK 0x3
#define CORE_DUPSTS 0x00420
#define CORE_DUPSTS_MASK 0x1ff
#define CORE_PAUSESTS 0x00428
#define PAUSESTS_TX_PAUSE_SHIFT 9
#define CORE_GMNCFGCFG 0x0800
#define RST_MIB_CNT (1 << 0)
#define RXBPDU_EN (1 << 1)
#define CORE_IMP0_PRT_ID 0x0804
#define CORE_BRCM_HDR_CTRL 0x0080c
#define BRCM_HDR_EN_P8 (1 << 0)
#define BRCM_HDR_EN_P5 (1 << 1)
#define BRCM_HDR_EN_P7 (1 << 2)
#define CORE_BRCM_HDR_CTRL2 0x0828
#define CORE_HL_PRTC_CTRL 0x0940
#define ARP_EN (1 << 0)
#define RARP_EN (1 << 1)
#define DHCP_EN (1 << 2)
#define ICMPV4_EN (1 << 3)
#define ICMPV6_EN (1 << 4)
#define ICMPV6_FWD_MODE (1 << 5)
#define IGMP_DIP_EN (1 << 8)
#define IGMP_RPTLVE_EN (1 << 9)
#define IGMP_RTPLVE_FWD_MODE (1 << 10)
#define IGMP_QRY_EN (1 << 11)
#define IGMP_QRY_FWD_MODE (1 << 12)
#define IGMP_UKN_EN (1 << 13)
#define IGMP_UKN_FWD_MODE (1 << 14)
#define MLD_RPTDONE_EN (1 << 15)
#define MLD_RPTDONE_FWD_MODE (1 << 16)
#define MLD_QRY_EN (1 << 17)
#define MLD_QRY_FWD_MODE (1 << 18)
#define CORE_RST_MIB_CNT_EN 0x0950
#define CORE_BRCM_HDR_RX_DIS 0x0980
#define CORE_BRCM_HDR_TX_DIS 0x0988
#define CORE_ARLA_NUM_ENTRIES 1024
#define CORE_ARLA_RWCTL 0x1400
#define ARL_RW (1 << 0)
#define IVL_SVL_SELECT (1 << 6)
#define ARL_STRTDN (1 << 7)
#define CORE_ARLA_MAC 0x1408
#define CORE_ARLA_VID 0x1420
#define ARLA_VIDTAB_INDX_MASK 0x1fff
#define CORE_ARLA_MACVID0 0x1440
#define MAC_MASK 0xffffffffff
#define VID_SHIFT 48
#define VID_MASK 0xfff
#define CORE_ARLA_FWD_ENTRY0 0x1460
#define PORTID_MASK 0x1ff
#define ARL_CON_SHIFT 9
#define ARL_CON_MASK 0x3
#define ARL_PRI_SHIFT 11
#define ARL_PRI_MASK 0x7
#define ARL_AGE (1 << 14)
#define ARL_STATIC (1 << 15)
#define ARL_VALID (1 << 16)
#define CORE_ARLA_MACVID_ENTRY(x) (CORE_ARLA_MACVID0 + ((x) * 0x40))
#define CORE_ARLA_FWD_ENTRY(x) (CORE_ARLA_FWD_ENTRY0 + ((x) * 0x40))
#define CORE_ARLA_SRCH_CTL 0x1540
#define ARLA_SRCH_VLID (1 << 0)
#define IVL_SVL_SELECT (1 << 6)
#define ARLA_SRCH_STDN (1 << 7)
#define CORE_ARLA_SRCH_ADR 0x1544
#define ARLA_SRCH_ADR_VALID (1 << 15)
#define CORE_ARLA_SRCH_RSLT_0_MACVID 0x1580
#define CORE_ARLA_SRCH_RSLT_0 0x15a0
#define CORE_ARLA_SRCH_RSLT_MACVID(x) (CORE_ARLA_SRCH_RSLT_0_MACVID + ((x) * 0x40))
#define CORE_ARLA_SRCH_RSLT(x) (CORE_ARLA_SRCH_RSLT_0 + ((x) * 0x40))
#define CORE_MEM_PSM_VDD_CTRL 0x2380
#define P_TXQ_PSM_VDD_SHIFT 2
#define P_TXQ_PSM_VDD_MASK 0x3
#define P_TXQ_PSM_VDD(x) (P_TXQ_PSM_VDD_MASK << \
((x) * P_TXQ_PSM_VDD_SHIFT))
#define CORE_P0_MIB_OFFSET 0x8000
#define P_MIB_SIZE 0x400
#define CORE_P_MIB_OFFSET(x) (CORE_P0_MIB_OFFSET + (x) * P_MIB_SIZE)
#define CORE_PORT_VLAN_CTL_PORT(x) (0xc400 + ((x) * 0x8))
#define PORT_VLAN_CTRL_MASK 0x1ff
#define CORE_EEE_EN_CTRL 0x24800
#define CORE_EEE_LPI_INDICATE 0x24810
#endif /* __BCM_SF2_REGS_H */