- 根目录:
- arch
- arm
- mach-bcmring
- csp
- chipc
- chipcHw_init.c
/*****************************************************************************
* Copyright 2003 - 2008 Broadcom Corporation. All rights reserved.
*
* Unless you and Broadcom execute a separate written software license
* agreement governing use of this software, this software is licensed to you
* under the terms of the GNU General Public License version 2, available at
* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
*
* Notwithstanding the above, under no circumstances may you combine this
* software in any way with any other Broadcom software provided under a
* license other than the GPL, without Broadcom's express prior written
* consent.
*****************************************************************************/
/****************************************************************************/
/**
* @file chipcHw_init.c
*
* @brief Low level CHIPC PLL configuration functions
*
* @note
*
* These routines provide basic PLL controlling functionality only.
*/
/****************************************************************************/
/* ---- Include Files ---------------------------------------------------- */
#include <csp/errno.h>
#include <csp/stdint.h>
#include <csp/module.h>
#include <mach/csp/chipcHw_def.h>
#include <mach/csp/chipcHw_inline.h>
#include <csp/reg.h>
#include <csp/delay.h>
/* ---- Private Constants and Types --------------------------------------- */
/*
Calculation for NDIV_i to obtain VCO frequency
-----------------------------------------------
Freq_vco = Freq_ref * (P2 / P1) * (PLL_NDIV_i + PLL_NDIV_f)
for Freq_vco = VCO_FREQ_MHz
Freq_ref = chipcHw_XTAL_FREQ_Hz
PLL_P1 = PLL_P2 = 1
and
PLL_NDIV_f = 0
We get:
PLL_NDIV_i = Freq_vco / Freq_ref = VCO_FREQ_MHz / chipcHw_XTAL_FREQ_Hz
Calculation for PLL MDIV to obtain frequency Freq_x for channel x
-----------------------------------------------------------------
Freq_x = chipcHw_XTAL_FREQ_Hz * PLL_NDIV_i / PLL_MDIV_x = VCO_FREQ_MHz / PLL_MDIV_x
PLL_MDIV_x = VCO_FREQ_MHz / Freq_x
*/
/* ---- Private Variables ------------------------------------------------- */
/****************************************************************************/
/**
* @brief Initializes the PLL2
*
* This function initializes the PLL2
*
*/
/****************************************************************************/
void chipcHw_pll2Enable(uint32_t vcoFreqHz)
{
uint32_t pllPreDivider2 = 0;
{
REG_LOCAL_IRQ_SAVE;
pChipcHw->PLLConfig2 =
chipcHw_REG_PLL_CONFIG_D_RESET |
chipcHw_REG_PLL_CONFIG_A_RESET;
pllPreDivider2 = chipcHw_REG_PLL_PREDIVIDER_POWER_DOWN |
chipcHw_REG_PLL_PREDIVIDER_NDIV_MODE_INTEGER |
(chipcHw_REG_PLL_PREDIVIDER_NDIV_i(vcoFreqHz) <<
chipcHw_REG_PLL_PREDIVIDER_NDIV_SHIFT) |
(chipcHw_REG_PLL_PREDIVIDER_P1 <<
chipcHw_REG_PLL_PREDIVIDER_P1_SHIFT) |
(chipcHw_REG_PLL_PREDIVIDER_P2 <<
chipcHw_REG_PLL_PREDIVIDER_P2_SHIFT);
/* Enable CHIPC registers to control the PLL */
pChipcHw->PLLStatus |= chipcHw_REG_PLL_STATUS_CONTROL_ENABLE;
/* Set pre divider to get desired VCO frequency */
pChipcHw->PLLPreDivider2 = pllPreDivider2;
/* Set NDIV Frac */
pChipcHw->PLLDivider2 = chipcHw_REG_PLL_DIVIDER_NDIV_f;
/* This has to be removed once the default values are fixed for PLL2. */
pChipcHw->PLLControl12 = 0x38000700;
pChipcHw->PLLControl22 = 0x00000015;
/* Reset PLL2 */
if (vcoFreqHz > chipcHw_REG_PLL_CONFIG_VCO_SPLIT_FREQ) {
pChipcHw->PLLConfig2 = chipcHw_REG_PLL_CONFIG_D_RESET |
chipcHw_REG_PLL_CONFIG_A_RESET |
chipcHw_REG_PLL_CONFIG_VCO_1601_3200 |
chipcHw_REG_PLL_CONFIG_POWER_DOWN;
} else {
pChipcHw->PLLConfig2 = chipcHw_REG_PLL_CONFIG_D_RESET |
chipcHw_REG_PLL_CONFIG_A_RESET |
chipcHw_REG_PLL_CONFIG_VCO_800_1600 |
chipcHw_REG_PLL_CONFIG_POWER_DOWN;
}
REG_LOCAL_IRQ_RESTORE;
}
/* Insert certain amount of delay before deasserting ARESET. */
udelay(1);
{
REG_LOCAL_IRQ_SAVE;
/* Remove analog reset and Power on the PLL */
pChipcHw->PLLConfig2 &=
~(chipcHw_REG_PLL_CONFIG_A_RESET |
chipcHw_REG_PLL_CONFIG_POWER_DOWN);
REG_LOCAL_IRQ_RESTORE;
}
/* Wait until PLL is locked */
while (!(pChipcHw->PLLStatus2 & chipcHw_REG_PLL_STATUS_LOCKED))
;
{
REG_LOCAL_IRQ_SAVE;
/* Remove digital reset */
pChipcHw->PLLConfig2 &= ~chipcHw_REG_PLL_CONFIG_D_RESET;
REG_LOCAL_IRQ_RESTORE;
}
}
EXPORT_SYMBOL(chipcHw_pll2Enable);
/****************************************************************************/
/**
* @brief Initializes the PLL1
*
* This function initializes the PLL1
*
*/
/****************************************************************************/
void chipcHw_pll1Enable(uint32_t vcoFreqHz, chipcHw_SPREAD_SPECTRUM_e ssSupport)
{
uint32_t pllPreDivider = 0;
{
REG_LOCAL_IRQ_SAVE;
pChipcHw->PLLConfig =
chipcHw_REG_PLL_CONFIG_D_RESET |
chipcHw_REG_PLL_CONFIG_A_RESET;
/* Setting VCO frequency */
if (ssSupport == chipcHw_SPREAD_SPECTRUM_ALLOW) {
pllPreDivider =
chipcHw_REG_PLL_PREDIVIDER_NDIV_MODE_MASH_1_8 |
((chipcHw_REG_PLL_PREDIVIDER_NDIV_i(vcoFreqHz) -
1) << chipcHw_REG_PLL_PREDIVIDER_NDIV_SHIFT) |
(chipcHw_REG_PLL_PREDIVIDER_P1 <<
chipcHw_REG_PLL_PREDIVIDER_P1_SHIFT) |
(chipcHw_REG_PLL_PREDIVIDER_P2 <<
chipcHw_REG_PLL_PREDIVIDER_P2_SHIFT);
} else {
pllPreDivider = chipcHw_REG_PLL_PREDIVIDER_POWER_DOWN |
chipcHw_REG_PLL_PREDIVIDER_NDIV_MODE_INTEGER |
(chipcHw_REG_PLL_PREDIVIDER_NDIV_i(vcoFreqHz) <<
chipcHw_REG_PLL_PREDIVIDER_NDIV_SHIFT) |
(chipcHw_REG_PLL_PREDIVIDER_P1 <<
chipcHw_REG_PLL_PREDIVIDER_P1_SHIFT) |
(chipcHw_REG_PLL_PREDIVIDER_P2 <<
chipcHw_REG_PLL_PREDIVIDER_P2_SHIFT);
}
/* Enable CHIPC registers to control the PLL */
pChipcHw->PLLStatus |= chipcHw_REG_PLL_STATUS_CONTROL_ENABLE;
/* Set pre divider to get desired VCO frequency */
pChipcHw->PLLPreDivider = pllPreDivider;
/* Set NDIV Frac */
if (ssSupport == chipcHw_SPREAD_SPECTRUM_ALLOW) {
pChipcHw->PLLDivider = chipcHw_REG_PLL_DIVIDER_M1DIV |
chipcHw_REG_PLL_DIVIDER_NDIV_f_SS;
} else {
pChipcHw->PLLDivider = chipcHw_REG_PLL_DIVIDER_M1DIV |
chipcHw_REG_PLL_DIVIDER_NDIV_f;
}
/* Reset PLL1 */
if (vcoFreqHz > chipcHw_REG_PLL_CONFIG_VCO_SPLIT_FREQ) {
pChipcHw->PLLConfig = chipcHw_REG_PLL_CONFIG_D_RESET |
chipcHw_REG_PLL_CONFIG_A_RESET |
chipcHw_REG_PLL_CONFIG_VCO_1601_3200 |
chipcHw_REG_PLL_CONFIG_POWER_DOWN;
} else {
pChipcHw->PLLConfig = chipcHw_REG_PLL_CONFIG_D_RESET |
chipcHw_REG_PLL_CONFIG_A_RESET |
chipcHw_REG_PLL_CONFIG_VCO_800_1600 |
chipcHw_REG_PLL_CONFIG_POWER_DOWN;
}
REG_LOCAL_IRQ_RESTORE;
/* Insert certain amount of delay before deasserting ARESET. */
udelay(1);
{
REG_LOCAL_IRQ_SAVE;
/* Remove analog reset and Power on the PLL */
pChipcHw->PLLConfig &=
~(chipcHw_REG_PLL_CONFIG_A_RESET |
chipcHw_REG_PLL_CONFIG_POWER_DOWN);
REG_LOCAL_IRQ_RESTORE;
}
/* Wait until PLL is locked */
while (!(pChipcHw->PLLStatus & chipcHw_REG_PLL_STATUS_LOCKED)
|| !(pChipcHw->
PLLStatus2 & chipcHw_REG_PLL_STATUS_LOCKED))
;
/* Remove digital reset */
{
REG_LOCAL_IRQ_SAVE;
pChipcHw->PLLConfig &= ~chipcHw_REG_PLL_CONFIG_D_RESET;
REG_LOCAL_IRQ_RESTORE;
}
}
}
EXPORT_SYMBOL(chipcHw_pll1Enable);
/****************************************************************************/
/**
* @brief Initializes the chipc module
*
* This function initializes the PLLs and core system clocks
*
*/
/****************************************************************************/
void chipcHw_Init(chipcHw_INIT_PARAM_t *initParam /* [ IN ] Misc chip initialization parameter */
) {
#if !(defined(__KERNEL__) && !defined(STANDALONE))
delay_init();
#endif
/* Do not program PLL, when warm reset */
if (!(chipcHw_getStickyBits() & chipcHw_REG_STICKY_CHIP_WARM_RESET)) {
chipcHw_pll1Enable(initParam->pllVcoFreqHz,
initParam->ssSupport);
chipcHw_pll2Enable(initParam->pll2VcoFreqHz);
} else {
/* Clear sticky bits */
chipcHw_clearStickyBits(chipcHw_REG_STICKY_CHIP_WARM_RESET);
}
/* Clear sticky bits */
chipcHw_clearStickyBits(chipcHw_REG_STICKY_CHIP_SOFT_RESET);
/* Before configuring the ARM clock, atleast we need to make sure BUS clock maintains the proper ratio with ARM clock */
pChipcHw->ACLKClock =
(pChipcHw->
ACLKClock & ~chipcHw_REG_ACLKClock_CLK_DIV_MASK) | (initParam->
armBusRatio &
chipcHw_REG_ACLKClock_CLK_DIV_MASK);
/* Set various core component frequencies. The order in which this is done is important for some. */
/* The RTBUS (DDR PHY) is derived from the BUS, and the BUS from the ARM, and VPM needs to know BUS */
/* frequency to find its ratio with the BUS. Hence we must set the ARM first, followed by the BUS, */
/* then VPM and RTBUS. */
chipcHw_setClockFrequency(chipcHw_CLOCK_ARM,
initParam->busClockFreqHz *
initParam->armBusRatio);
chipcHw_setClockFrequency(chipcHw_CLOCK_BUS, initParam->busClockFreqHz);
chipcHw_setClockFrequency(chipcHw_CLOCK_VPM,
initParam->busClockFreqHz *
initParam->vpmBusRatio);
chipcHw_setClockFrequency(chipcHw_CLOCK_DDR,
initParam->busClockFreqHz *
initParam->ddrBusRatio);
chipcHw_setClockFrequency(chipcHw_CLOCK_RTBUS,
initParam->busClockFreqHz / 2);
}