- 根目录:
- Documentation
- devicetree
- bindings
- usb
- omap-usb.txt
OMAP GLUE AND OTHER OMAP SPECIFIC COMPONENTS
OMAP MUSB GLUE
- compatible : Should be "ti,omap4-musb" or "ti,omap3-musb"
- ti,hwmods : must be "usb_otg_hs"
- multipoint : Should be "1" indicating the musb controller supports
multipoint. This is a MUSB configuration-specific setting.
- num-eps : Specifies the number of endpoints. This is also a
MUSB configuration-specific setting. Should be set to "16"
- ram-bits : Specifies the ram address size. Should be set to "12"
- interface-type : This is a board specific setting to describe the type of
interface between the controller and the phy. It should be "0" or "1"
specifying ULPI and UTMI respectively.
- mode : Should be "3" to represent OTG. "1" signifies HOST and "2"
represents PERIPHERAL.
- power : Should be "50". This signifies the controller can supply up to
100mA when operating in host mode.
- usb-phy : the phandle for the PHY device
- phys : the phandle for the PHY device (used by generic PHY framework)
- phy-names : the names of the PHY corresponding to the PHYs present in the
*phy* phandle.
Optional properties:
- ctrl-module : phandle of the control module this glue uses to write to
mailbox
SOC specific device node entry
usb_otg_hs: usb_otg_hs@4a0ab000 {
compatible = "ti,omap4-musb";
ti,hwmods = "usb_otg_hs";
multipoint = <1>;
num-eps = <16>;
ram-bits = <12>;
ctrl-module = <&omap_control_usb>;
phys = <&usb2_phy>;
phy-names = "usb2-phy";
};
Board specific device node entry
&usb_otg_hs {
interface-type = <1>;
mode = <3>;
power = <50>;
};
OMAP DWC3 GLUE
- compatible : Should be
* "ti,dwc3" for OMAP5 and DRA7
* "ti,am437x-dwc3" for AM437x
- ti,hwmods : Should be "usb_otg_ss"
- reg : Address and length of the register set for the device.
- interrupts : The irq number of this device that is used to interrupt the
MPU
-
- utmi-mode : controls the source of UTMI/PIPE status for VBUS and OTG ID.
It should be set to "1" for HW mode and "2" for SW mode.
- ranges: the child address space are mapped 1:1 onto the parent address space
Optional Properties:
- extcon : phandle for the extcon device omap dwc3 uses to detect
connect/disconnect events.
- vbus-supply : phandle to the regulator device tree node if needed.
Sub-nodes:
The dwc3 core should be added as subnode to omap dwc3 glue.
- dwc3 :
The binding details of dwc3 can be found in:
Documentation/devicetree/bindings/usb/dwc3.txt
omap_dwc3 {
compatible = "ti,dwc3";
ti,hwmods = "usb_otg_ss";
reg = <0x4a020000 0x1ff>;
interrupts = <0 93 4>;
utmi-mode = <2>;
ranges;
};
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- 24
- 25
- 26
- 27
- 28
- 29
- 30
- 31
- 32
- 33
- 34
- 35
- 36
- 37
- 38
- 39
- 40
- 41
- 42
- 43
- 44
- 45
- 46
- 47
- 48
- 49
- 50
- 51
- 52
- 53
- 54
- 55
- 56
- 57
- 58
- 59
- 60
- 61
- 62
- 63
- 64
- 65
- 66
- 67
- 68
- 69
- 70
- 71
- 72
- 73
- 74
- 75
- 76
- 77
- 78
- 79
- 80