- 根目录:
- Documentation
- devicetree
- bindings
- gpu
- nvidia,tegra20-host1x.txt
NVIDIA Tegra host1x
Required properties:
- compatible: "nvidia,tegra<chip>-host1x"
- reg: Physical base address and length of the controller's registers.
- interrupts: The interrupt outputs from the controller.
- #address-cells: The number of cells used to represent physical base addresses
in the host1x address space. Should be 1.
- #size-cells: The number of cells used to represent the size of an address
range in the host1x address space. Should be 1.
- ranges: The mapping of the host1x address space to the CPU address space.
- clocks: Must contain one entry, for the module clock.
See ../clocks/clock-bindings.txt for details.
- resets: Must contain an entry for each entry in reset-names.
See ../reset/reset.txt for details.
- reset-names: Must include the following entries:
- host1x
The host1x top-level node defines a number of children, each representing one
of the following host1x client modules:
- mpe: video encoder
Required properties:
- compatible: "nvidia,tegra<chip>-mpe"
- reg: Physical base address and length of the controller's registers.
- interrupts: The interrupt outputs from the controller.
- clocks: Must contain one entry, for the module clock.
See ../clocks/clock-bindings.txt for details.
- resets: Must contain an entry for each entry in reset-names.
See ../reset/reset.txt for details.
- reset-names: Must include the following entries:
- mpe
- vi: video input
Required properties:
- compatible: "nvidia,tegra<chip>-vi"
- reg: Physical base address and length of the controller's registers.
- interrupts: The interrupt outputs from the controller.
- clocks: Must contain one entry, for the module clock.
See ../clocks/clock-bindings.txt for details.
- resets: Must contain an entry for each entry in reset-names.
See ../reset/reset.txt for details.
- reset-names: Must include the following entries:
- vi
- epp: encoder pre-processor
Required properties:
- compatible: "nvidia,tegra<chip>-epp"
- reg: Physical base address and length of the controller's registers.
- interrupts: The interrupt outputs from the controller.
- clocks: Must contain one entry, for the module clock.
See ../clocks/clock-bindings.txt for details.
- resets: Must contain an entry for each entry in reset-names.
See ../reset/reset.txt for details.
- reset-names: Must include the following entries:
- epp
- isp: image signal processor
Required properties:
- compatible: "nvidia,tegra<chip>-isp"
- reg: Physical base address and length of the controller's registers.
- interrupts: The interrupt outputs from the controller.
- clocks: Must contain one entry, for the module clock.
See ../clocks/clock-bindings.txt for details.
- resets: Must contain an entry for each entry in reset-names.
See ../reset/reset.txt for details.
- reset-names: Must include the following entries:
- isp
- gr2d: 2D graphics engine
Required properties:
- compatible: "nvidia,tegra<chip>-gr2d"
- reg: Physical base address and length of the controller's registers.
- interrupts: The interrupt outputs from the controller.
- clocks: Must contain one entry, for the module clock.
See ../clocks/clock-bindings.txt for details.
- resets: Must contain an entry for each entry in reset-names.
See ../reset/reset.txt for details.
- reset-names: Must include the following entries:
- 2d
- gr3d: 3D graphics engine
Required properties:
- compatible: "nvidia,tegra<chip>-gr3d"
- reg: Physical base address and length of the controller's registers.
- clocks: Must contain an entry for each entry in clock-names.
See ../clocks/clock-bindings.txt for details.
- clock-names: Must include the following entries:
(This property may be omitted if the only clock in the list is "3d")
- 3d
This MUST be the first entry.
- 3d2 (Only required on SoCs with two 3D clocks)
- resets: Must contain an entry for each entry in reset-names.
See ../reset/reset.txt for details.
- reset-names: Must include the following entries:
- 3d
- 3d2 (Only required on SoCs with two 3D clocks)
- dc: display controller
Required properties:
- compatible: "nvidia,tegra<chip>-dc"
- reg: Physical base address and length of the controller's registers.
- interrupts: The interrupt outputs from the controller.
- clocks: Must contain an entry for each entry in clock-names.
See ../clocks/clock-bindings.txt for details.
- clock-names: Must include the following entries:
- dc
This MUST be the first entry.
- parent
- resets: Must contain an entry for each entry in reset-names.
See ../reset/reset.txt for details.
- reset-names: Must include the following entries:
- dc
- nvidia,head: The number of the display controller head. This is used to
setup the various types of output to receive video data from the given
head.
Each display controller node has a child node, named "rgb", that represents
the RGB output associated with the controller. It can take the following
optional properties:
- nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
- nvidia,hpd-gpio: specifies a GPIO used for hotplug detection
- nvidia,edid: supplies a binary EDID blob
- nvidia,panel: phandle of a display panel
- hdmi: High Definition Multimedia Interface
Required properties:
- compatible: "nvidia,tegra<chip>-hdmi"
- reg: Physical base address and length of the controller's registers.
- interrupts: The interrupt outputs from the controller.
- hdmi-supply: supply for the +5V HDMI connector pin
- vdd-supply: regulator for supply voltage
- pll-supply: regulator for PLL
- clocks: Must contain an entry for each entry in clock-names.
See ../clocks/clock-bindings.txt for details.
- clock-names: Must include the following entries:
- hdmi
This MUST be the first entry.
- parent
- resets: Must contain an entry for each entry in reset-names.
See ../reset/reset.txt for details.
- reset-names: Must include the following entries:
- hdmi
Optional properties:
- nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
- nvidia,hpd-gpio: specifies a GPIO used for hotplug detection
- nvidia,edid: supplies a binary EDID blob
- nvidia,panel: phandle of a display panel
- tvo: TV encoder output
Required properties:
- compatible: "nvidia,tegra<chip>-tvo"
- reg: Physical base address and length of the controller's registers.
- interrupts: The interrupt outputs from the controller.
- clocks: Must contain one entry, for the module clock.
See ../clocks/clock-bindings.txt for details.
- dsi: display serial interface
Required properties:
- compatible: "nvidia,tegra<chip>-dsi"
- reg: Physical base address and length of the controller's registers.
- clocks: Must contain an entry for each entry in clock-names.
See ../clocks/clock-bindings.txt for details.
- clock-names: Must include the following entries:
- dsi
This MUST be the first entry.
- lp
- parent
- resets: Must contain an entry for each entry in reset-names.
See ../reset/reset.txt for details.
- reset-names: Must include the following entries:
- dsi
- avdd-dsi-supply: phandle of a supply that powers the DSI controller
- nvidia,mipi-calibrate: Should contain a phandle and a specifier specifying
which pads are used by this DSI output and need to be calibrated. See also
../mipi/nvidia,tegra114-mipi.txt.
Optional properties:
- nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
- nvidia,hpd-gpio: specifies a GPIO used for hotplug detection
- nvidia,edid: supplies a binary EDID blob
- nvidia,panel: phandle of a display panel
- sor: serial output resource
Required properties:
- compatible: "nvidia,tegra124-sor"
- reg: Physical base address and length of the controller's registers.
- interrupts: The interrupt outputs from the controller.
- clocks: Must contain an entry for each entry in clock-names.
See ../clocks/clock-bindings.txt for details.
- clock-names: Must include the following entries:
- sor: clock input for the SOR hardware
- parent: input for the pixel clock
- dp: reference clock for the SOR clock
- safe: safe reference for the SOR clock during power up
- resets: Must contain an entry for each entry in reset-names.
See ../reset/reset.txt for details.
- reset-names: Must include the following entries:
- sor
Optional properties:
- nvidia,ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
- nvidia,hpd-gpio: specifies a GPIO used for hotplug detection
- nvidia,edid: supplies a binary EDID blob
- nvidia,panel: phandle of a display panel
Optional properties when driving an eDP output:
- nvidia,dpaux: phandle to a DispayPort AUX interface
- dpaux: DisplayPort AUX interface
- compatible: "nvidia,tegra124-dpaux"
- reg: Physical base address and length of the controller's registers.
- interrupts: The interrupt outputs from the controller.
- clocks: Must contain an entry for each entry in clock-names.
See ../clocks/clock-bindings.txt for details.
- clock-names: Must include the following entries:
- dpaux: clock input for the DPAUX hardware
- parent: reference clock
- resets: Must contain an entry for each entry in reset-names.
See ../reset/reset.txt for details.
- reset-names: Must include the following entries:
- dpaux
- vdd-supply: phandle of a supply that powers the DisplayPort link
Example:
/ {
...
host1x {
compatible = "nvidia,tegra20-host1x", "simple-bus";
reg = <0x50000000 0x00024000>;
interrupts = <0 65 0x04 /* mpcore syncpt */
0 67 0x04>; /* mpcore general */
clocks = <&tegra_car TEGRA20_CLK_HOST1X>;
resets = <&tegra_car 28>;
reset-names = "host1x";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x54000000 0x54000000 0x04000000>;
mpe {
compatible = "nvidia,tegra20-mpe";
reg = <0x54040000 0x00040000>;
interrupts = <0 68 0x04>;
clocks = <&tegra_car TEGRA20_CLK_MPE>;
resets = <&tegra_car 60>;
reset-names = "mpe";
};
vi {
compatible = "nvidia,tegra20-vi";
reg = <0x54080000 0x00040000>;
interrupts = <0 69 0x04>;
clocks = <&tegra_car TEGRA20_CLK_VI>;
resets = <&tegra_car 100>;
reset-names = "vi";
};
epp {
compatible = "nvidia,tegra20-epp";
reg = <0x540c0000 0x00040000>;
interrupts = <0 70 0x04>;
clocks = <&tegra_car TEGRA20_CLK_EPP>;
resets = <&tegra_car 19>;
reset-names = "epp";
};
isp {
compatible = "nvidia,tegra20-isp";
reg = <0x54100000 0x00040000>;
interrupts = <0 71 0x04>;
clocks = <&tegra_car TEGRA20_CLK_ISP>;
resets = <&tegra_car 23>;
reset-names = "isp";
};
gr2d {
compatible = "nvidia,tegra20-gr2d";
reg = <0x54140000 0x00040000>;
interrupts = <0 72 0x04>;
clocks = <&tegra_car TEGRA20_CLK_GR2D>;
resets = <&tegra_car 21>;
reset-names = "2d";
};
gr3d {
compatible = "nvidia,tegra20-gr3d";
reg = <0x54180000 0x00040000>;
clocks = <&tegra_car TEGRA20_CLK_GR3D>;
resets = <&tegra_car 24>;
reset-names = "3d";
};
dc@54200000 {
compatible = "nvidia,tegra20-dc";
reg = <0x54200000 0x00040000>;
interrupts = <0 73 0x04>;
clocks = <&tegra_car TEGRA20_CLK_DISP1>,
<&tegra_car TEGRA20_CLK_PLL_P>;
clock-names = "dc", "parent";
resets = <&tegra_car 27>;
reset-names = "dc";
rgb {
status = "disabled";
};
};
dc@54240000 {
compatible = "nvidia,tegra20-dc";
reg = <0x54240000 0x00040000>;
interrupts = <0 74 0x04>;
clocks = <&tegra_car TEGRA20_CLK_DISP2>,
<&tegra_car TEGRA20_CLK_PLL_P>;
clock-names = "dc", "parent";
resets = <&tegra_car 26>;
reset-names = "dc";
rgb {
status = "disabled";
};
};
hdmi {
compatible = "nvidia,tegra20-hdmi";
reg = <0x54280000 0x00040000>;
interrupts = <0 75 0x04>;
clocks = <&tegra_car TEGRA20_CLK_HDMI>,
<&tegra_car TEGRA20_CLK_PLL_D_OUT0>;
clock-names = "hdmi", "parent";
resets = <&tegra_car 51>;
reset-names = "hdmi";
status = "disabled";
};
tvo {
compatible = "nvidia,tegra20-tvo";
reg = <0x542c0000 0x00040000>;
interrupts = <0 76 0x04>;
clocks = <&tegra_car TEGRA20_CLK_TVO>;
status = "disabled";
};
dsi {
compatible = "nvidia,tegra20-dsi";
reg = <0x54300000 0x00040000>;
clocks = <&tegra_car TEGRA20_CLK_DSI>,
<&tegra_car TEGRA20_CLK_PLL_D_OUT0>;
clock-names = "dsi", "parent";
resets = <&tegra_car 48>;
reset-names = "dsi";
status = "disabled";
};
};
...
};