#ifndef SOUND_FIREWIRE_DICE_INTERFACE_H_INCLUDED #define SOUND_FIREWIRE_DICE_INTERFACE_H_INCLUDED /* * DICE device interface definitions */ /* * Generally, all registers can be read like memory, i.e., with quadlet read or * block read transactions with at least quadlet-aligned offset and length. * Writes are not allowed except where noted; quadlet-sized registers must be * written with a quadlet write transaction. * * All values are in big endian. The DICE firmware runs on a little-endian CPU * and just byte-swaps _all_ quadlets on the bus, so values without endianness * (e.g. strings) get scrambled and must be byte-swapped again by the driver. */ /* * Streaming is handled by the "DICE driver" interface. Its registers are * located in this private address space. */ #define DICE_PRIVATE_SPACE 0xffffe0000000uLL /* * The registers are organized in several sections, which are organized * separately to allow them to be extended individually. Whether a register is * supported can be detected by checking its offset against its section's size. * * The section offset values are relative to DICE_PRIVATE_SPACE; the offset/ * size values are measured in quadlets. Read-only. */ #define DICE_GLOBAL_OFFSET 0x00 #define DICE_GLOBAL_SIZE 0x04 #define DICE_TX_OFFSET 0x08 #define DICE_TX_SIZE 0x0c #define DICE_RX_OFFSET 0x10 #define DICE_RX_SIZE 0x14 #define DICE_EXT_SYNC_OFFSET 0x18 #define DICE_EXT_SYNC_SIZE 0x1c #define DICE_UNUSED2_OFFSET 0x20 #define DICE_UNUSED2_SIZE 0x24 /* * Global settings. */ /* * Stores the full 64-bit address (node ID and offset in the node's address * space) where the device will send notifications. Must be changed with * a compare/swap transaction by the owner. This register is automatically * cleared on a bus reset. */ #define GLOBAL_OWNER 0x000 #define OWNER_NO_OWNER 0xffff000000000000uLL #define OWNER_NODE_SHIFT 48 /* * A bitmask with asynchronous events; read-only. When any event(s) happen, * the bits of previous events are cleared, and the value of this register is * also written to the address stored in the owner register. */ #define GLOBAL_NOTIFICATION 0x008 /* Some registers in the Rx/Tx sections may have changed. */ #define NOTIFY_RX_CFG_CHG 0x00000001 #define NOTIFY_TX_CFG_CHG 0x00000002 /* Lock status of the current clock source may have changed. */ #define NOTIFY_LOCK_CHG 0x00000010 /* Write to the clock select register has been finished. */ #define NOTIFY_CLOCK_ACCEPTED 0x00000020 /* Lock status of some clock source has changed. */ #define NOTIFY_EXT_STATUS 0x00000040 /* Other bits may be used for device-specific events. */ /* * A name that can be customized for each device; read/write. Padded with zero * bytes. Quadlets are byte-swapped. The encoding is whatever the host driver * happens to be using. */ #define GLOBAL_NICK_NAME 0x00c #define NICK_NAME_SIZE 64 /* * The current sample rate and clock source; read/write. Whether a clock * source or sample rate is supported is device-specific; the internal clock * source is always available. Low/mid/high = up to 48/96/192 kHz. This * register can be changed even while streams are running. */ #define GLOBAL_CLOCK_SELECT 0x04c #define CLOCK_SOURCE_MASK 0x000000ff #define CLOCK_SOURCE_AES1 0x00000000 #define CLOCK_SOURCE_AES2 0x00000001 #define CLOCK_SOURCE_AES3 0x00000002 #define CLOCK_SOURCE_AES4 0x00000003 #define CLOCK_SOURCE_AES_ANY 0x00000004 #define CLOCK_SOURCE_ADAT 0x00000005 #define CLOCK_SOURCE_TDIF 0x00000006 #define CLOCK_SOURCE_WC 0x00000007 #define CLOCK_SOURCE_ARX1 0x00000008 #define CLOCK_SOURCE_ARX2 0x00000009 #define CLOCK_SOURCE_ARX3 0x0000000a #define CLOCK_SOURCE_ARX4 0x0000000b #define CLOCK_SOURCE_INTERNAL 0x0000000c #define CLOCK_RATE_MASK 0x0000ff00 #define CLOCK_RATE_32000 0x00000000 #define CLOCK_RATE_44100 0x00000100 #define CLOCK_RATE_48000 0x00000200 #define CLOCK_RATE_88200 0x00000300 #define CLOCK_RATE_96000 0x00000400 #define CLOCK_RATE_176400 0x00000500 #define CLOCK_RATE_192000 0x00000600 #define CLOCK_RATE_ANY_LOW 0x00000700 #define CLOCK_RATE_ANY_MID 0x00000800 #define CLOCK_RATE_ANY_HIGH 0x00000900 #define CLOCK_RATE_NONE 0x00000a00 #define CLOCK_RATE_SHIFT 8 /* * Enable streaming; read/write. Writing a non-zero value (re)starts all * streams that have a valid iso channel set; zero stops all streams. The * streams' parameters must be configured before starting. This register is * automatically cleared on a bus reset. */ #define GLOBAL_ENABLE 0x050 /* * Status of the sample clock; read-only. */ #define GLOBAL_STATUS 0x054 /* The current clock source is locked. */ #define STATUS_SOURCE_LOCKED 0x00000001 /* The actual sample rate; CLOCK_RATE_32000-_192000 or _NONE. */ #define STATUS_NOMINAL_RATE_MASK 0x0000ff00 /* * Status of all clock sources; read-only. */ #define GLOBAL_EXTENDED_STATUS 0x058 /* * The _LOCKED bits always show the current status; any change generates * a notification. */ #define EXT_STATUS_AES1_LOCKED 0x00000001 #define EXT_STATUS_AES2_LOCKED 0x00000002 #define EXT_STATUS_AES3_LOCKED 0x00000004 #define EXT_STATUS_AES4_LOCKED 0x00000008 #define EXT_STATUS_ADAT_LOCKED 0x00000010 #define EXT_STATUS_TDIF_LOCKED 0x00000020 #define EXT_STATUS_ARX1_LOCKED 0x00000040 #define EXT_STATUS_ARX2_LOCKED 0x00000080 #define EXT_STATUS_ARX3_LOCKED 0x00000100 #define EXT_STATUS_ARX4_LOCKED 0x00000200 #define EXT_STATUS_WC_LOCKED 0x00000400 /* * The _SLIP bits do not generate notifications; a set bit indicates that an * error occurred since the last time when this register was read with * a quadlet read transaction. */ #define EXT_STATUS_AES1_SLIP 0x00010000 #define EXT_STATUS_AES2_SLIP 0x00020000 #define EXT_STATUS_AES3_SLIP 0x00040000 #define EXT_STATUS_AES4_SLIP 0x00080000 #define EXT_STATUS_ADAT_SLIP 0x00100000 #define EXT_STATUS_TDIF_SLIP 0x00200000 #define EXT_STATUS_ARX1_SLIP 0x00400000 #define EXT_STATUS_ARX2_SLIP 0x00800000 #define EXT_STATUS_ARX3_SLIP 0x01000000 #define EXT_STATUS_ARX4_SLIP 0x02000000 #define EXT_STATUS_WC_SLIP 0x04000000 /* * The measured rate of the current clock source, in Hz; read-only. */ #define GLOBAL_SAMPLE_RATE 0x05c /* * The version of the DICE driver specification that this device conforms to; * read-only. */ #define GLOBAL_VERSION 0x060 /* Some old firmware versions do not have the following global registers: */ /* * Supported sample rates and clock sources; read-only. */ #define GLOBAL_CLOCK_CAPABILITIES 0x064 #define CLOCK_CAP_RATE_32000 0x00000001 #define CLOCK_CAP_RATE_44100 0x00000002 #define CLOCK_CAP_RATE_48000 0x00000004 #define CLOCK_CAP_RATE_88200 0x00000008 #define CLOCK_CAP_RATE_96000 0x00000010 #define CLOCK_CAP_RATE_176400 0x00000020 #define CLOCK_CAP_RATE_192000 0x00000040 #define CLOCK_CAP_SOURCE_AES1 0x00010000 #define CLOCK_CAP_SOURCE_AES2 0x00020000 #define CLOCK_CAP_SOURCE_AES3 0x00040000 #define CLOCK_CAP_SOURCE_AES4 0x00080000 #define CLOCK_CAP_SOURCE_AES_ANY 0x00100000 #define CLOCK_CAP_SOURCE_ADAT 0x00200000 #define CLOCK_CAP_SOURCE_TDIF 0x00400000 #define CLOCK_CAP_SOURCE_WC 0x00800000 #define CLOCK_CAP_SOURCE_ARX1 0x01000000 #define CLOCK_CAP_SOURCE_ARX2 0x02000000 #define CLOCK_CAP_SOURCE_ARX3 0x04000000 #define CLOCK_CAP_SOURCE_ARX4 0x08000000 #define CLOCK_CAP_SOURCE_INTERNAL 0x10000000 /* * Names of all clock sources; read-only. Quadlets are byte-swapped. Names * are separated with one backslash, the list is terminated with two * backslashes. Unused clock sources are included. */ #define GLOBAL_CLOCK_SOURCE_NAMES 0x068 #define CLOCK_SOURCE_NAMES_SIZE 256 /* * Capture stream settings. This section includes the number/size registers * and the registers of all streams. */ /* * The number of supported capture streams; read-only. */ #define TX_NUMBER 0x000 /* * The size of one stream's register block, in quadlets; read-only. The * registers of the first stream follow immediately afterwards; the registers * of the following streams are offset by this register's value. */ #define TX_SIZE 0x004 /* * The isochronous channel number on which packets are sent, or -1 if the * stream is not to be used; read/write. */ #define TX_ISOCHRONOUS 0x008 /* * The number of audio channels; read-only. There will be one quadlet per * channel; the first channel is the first quadlet in a data block. */ #define TX_NUMBER_AUDIO 0x00c /* * The number of MIDI ports, 0-8; read-only. If > 0, there will be one * additional quadlet in each data block, following the audio quadlets. */ #define TX_NUMBER_MIDI 0x010 /* * The speed at which the packets are sent, SCODE_100-_400; read/write. */ #define TX_SPEED 0x014 /* * Names of all audio channels; read-only. Quadlets are byte-swapped. Names * are separated with one backslash, the list is terminated with two * backslashes. */ #define TX_NAMES 0x018 #define TX_NAMES_SIZE 256 /* * Audio IEC60958 capabilities; read-only. Bitmask with one bit per audio * channel. */ #define TX_AC3_CAPABILITIES 0x118 /* * Send audio data with IEC60958 label; read/write. Bitmask with one bit per * audio channel. This register can be changed even while the stream is * running. */ #define TX_AC3_ENABLE 0x11c /* * Playback stream settings. This section includes the number/size registers * and the registers of all streams. */ /* * The number of supported playback streams; read-only. */ #define RX_NUMBER 0x000 /* * The size of one stream's register block, in quadlets; read-only. The * registers of the first stream follow immediately afterwards; the registers * of the following streams are offset by this register's value. */ #define RX_SIZE 0x004 /* * The isochronous channel number on which packets are received, or -1 if the * stream is not to be used; read/write. */ #define RX_ISOCHRONOUS 0x008 /* * Index of first quadlet to be interpreted; read/write. If > 0, that many * quadlets at the beginning of each data block will be ignored, and all the * audio and MIDI quadlets will follow. */ #define RX_SEQ_START 0x00c /* * The number of audio channels; read-only. There will be one quadlet per * channel. */ #define RX_NUMBER_AUDIO 0x010 /* * The number of MIDI ports, 0-8; read-only. If > 0, there will be one * additional quadlet in each data block, following the audio quadlets. */ #define RX_NUMBER_MIDI 0x014 /* * Names of all audio channels; read-only. Quadlets are byte-swapped. Names * are separated with one backslash, the list is terminated with two * backslashes. */ #define RX_NAMES 0x018 #define RX_NAMES_SIZE 256 /* * Audio IEC60958 capabilities; read-only. Bitmask with one bit per audio * channel. */ #define RX_AC3_CAPABILITIES 0x118 /* * Receive audio data with IEC60958 label; read/write. Bitmask with one bit * per audio channel. This register can be changed even while the stream is * running. */ #define RX_AC3_ENABLE 0x11c /* * Extended synchronization information. * This section can be read completely with a block read request. */ /* * Current clock source; read-only. */ #define EXT_SYNC_CLOCK_SOURCE 0x000 /* * Clock source is locked (boolean); read-only. */ #define EXT_SYNC_LOCKED 0x004 /* * Current sample rate (CLOCK_RATE_* >> CLOCK_RATE_SHIFT), _32000-_192000 or * _NONE; read-only. */ #define EXT_SYNC_RATE 0x008 /* * ADAT user data bits; read-only. */ #define EXT_SYNC_ADAT_USER_DATA 0x00c /* The data bits, if available. */ #define ADAT_USER_DATA_MASK 0x0f /* The data bits are not available. */ #define ADAT_USER_DATA_NO_DATA 0x10 #endif