/*
* Timer/Counter Unit (TC) registers.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
#ifndef ATMEL_TC_H
#define ATMEL_TC_H
#include <linux/compiler.h>
#include <linux/list.h>
/*
* Many 32-bit Atmel SOCs include one or more TC blocks, each of which holds
* three general-purpose 16-bit timers. These timers share one register bank.
* Depending on the SOC, each timer may have its own clock and IRQ, or those
* may be shared by the whole TC block.
*
* These TC blocks may have up to nine external pins: TCLK0..2 signals for
* clocks or clock gates, and per-timer TIOA and TIOB signals used for PWM
* or triggering. Those pins need to be set up for use with the TC block,
* else they will be used as GPIOs or for a different controller.
*
* Although we expect each TC block to have a platform_device node, those
* nodes are not what drivers bind to. Instead, they ask for a specific
* TC block, by number ... which is a common approach on systems with many
* timers. Then they use clk_get() and platform_get_irq() to get clock and
* IRQ resources.
*/
struct clk;
/**
* struct atmel_tcb_config - SoC data for a Timer/Counter Block
* @counter_width: size in bits of a timer counter register
*/
struct atmel_tcb_config {
size_t counter_width;
};
/**
* struct atmel_tc - information about a Timer/Counter Block
* @pdev: physical device
* @iomem: resource associated with the I/O register
* @regs: mapping through which the I/O registers can be accessed
* @tcb_config: configuration data from SoC
* @irq: irq for each of the three channels
* @clk: internal clock source for each of the three channels
* @node: list node, for tclib internal use
*
* On some platforms, each TC channel has its own clocks and IRQs,
* while on others, all TC channels share the same clock and IRQ.
* Drivers should clk_enable() all the clocks they need even though
* all the entries in @clk may point to the same physical clock.
* Likewise, drivers should request irqs independently for each
* channel, but they must use IRQF_SHARED in case some of the entries
* in @irq are actually the same IRQ.
*/
struct atmel_tc {
struct platform_device *pdev;
struct resource *iomem;
void __iomem *regs;
const struct atmel_tcb_config *tcb_config;
int irq[3];
struct clk *clk[3];
struct list_head node;
};
extern struct atmel_tc *atmel_tc_alloc(unsigned block, const char *name);
extern void atmel_tc_free(struct atmel_tc *tc);
/* platform-specific ATMEL_TC_TIMER_CLOCKx divisors (0 means 32KiHz) */
extern const u8 atmel_tc_divisors[5];
/*
* Two registers have block-wide controls. These are: configuring the three
* "external" clocks (or event sources) used by the timer channels; and
* synchronizing the timers by resetting them all at once.
*
* "External" can mean "external to chip" using the TCLK0, TCLK1, or TCLK2
* signals. Or, it can mean "external to timer", using the TIOA output from
* one of the other two timers that's being run in waveform mode.
*/
#define ATMEL_TC_BCR 0xc0 /* TC Block Control Register */
#define ATMEL_TC_SYNC (1 << 0) /* synchronize timers */
#define ATMEL_TC_BMR 0xc4 /* TC Block Mode Register */
#define ATMEL_TC_TC0XC0S (3 << 0) /* external clock 0 source */
#define ATMEL_TC_TC0XC0S_TCLK0 (0 << 0)
#define ATMEL_TC_TC0XC0S_NONE (1 << 0)
#define ATMEL_TC_TC0XC0S_TIOA1 (2 << 0)
#define ATMEL_TC_TC0XC0S_TIOA2 (3 << 0)
#define ATMEL_TC_TC1XC1S (3 << 2) /* external clock 1 source */
#define ATMEL_TC_TC1XC1S_TCLK1 (0 << 2)
#define ATMEL_TC_TC1XC1S_NONE (1 << 2)
#define ATMEL_TC_TC1XC1S_TIOA0 (2 << 2)
#define ATMEL_TC_TC1XC1S_TIOA2 (3 << 2)
#define ATMEL_TC_TC2XC2S (3 << 4) /* external clock 2 source */
#define ATMEL_TC_TC2XC2S_TCLK2 (0 << 4)
#define ATMEL_TC_TC2XC2S_NONE (1 << 4)
#define ATMEL_TC_TC2XC2S_TIOA0 (2 << 4)
#define ATMEL_TC_TC2XC2S_TIOA1 (3 << 4)
/*
* Each TC block has three "channels", each with one counter and controls.
*
* Note that the semantics of ATMEL_TC_TIMER_CLOCKx (input clock selection
* when it's not "external") is silicon-specific. AT91 platforms use one
* set of definitions; AVR32 platforms use a different set. Don't hard-wire
* such knowledge into your code, use the global "atmel_tc_divisors" ...
* where index N is the divisor for clock N+1, else zero to indicate it uses
* the 32 KiHz clock.
*
* The timers can be chained in various ways, and operated in "waveform"
* generation mode (including PWM) or "capture" mode (to time events). In
* both modes, behavior can be configured in many ways.
*
* Each timer has two I/O pins, TIOA and TIOB. Waveform mode uses TIOA as a
* PWM output, and TIOB as either another PWM or as a trigger. Capture mode
* uses them only as inputs.
*/
#define ATMEL_TC_CHAN(idx) ((idx)*0x40)
#define ATMEL_TC_REG(idx, reg) (ATMEL_TC_CHAN(idx) + ATMEL_TC_ ## reg)
#define ATMEL_TC_CCR 0x00 /* Channel Control Register */
#define ATMEL_TC_CLKEN (1 << 0) /* clock enable */
#define ATMEL_TC_CLKDIS (1 << 1) /* clock disable */
#define ATMEL_TC_SWTRG (1 << 2) /* software trigger */
#define ATMEL_TC_CMR 0x04 /* Channel Mode Register */
/* Both modes share some CMR bits */
#define ATMEL_TC_TCCLKS (7 << 0) /* clock source */
#define ATMEL_TC_TIMER_CLOCK1 (0 << 0)
#define ATMEL_TC_TIMER_CLOCK2 (1 << 0)
#define ATMEL_TC_TIMER_CLOCK3 (2 << 0)
#define ATMEL_TC_TIMER_CLOCK4 (3 << 0)
#define ATMEL_TC_TIMER_CLOCK5 (4 << 0)
#define ATMEL_TC_XC0 (5 << 0)
#define ATMEL_TC_XC1 (6 << 0)
#define ATMEL_TC_XC2 (7 << 0)
#define ATMEL_TC_CLKI (1 << 3) /* clock invert */
#define ATMEL_TC_BURST (3 << 4) /* clock gating */
#define ATMEL_TC_GATE_NONE (0 << 4)
#define ATMEL_TC_GATE_XC0 (1 << 4)
#define ATMEL_TC_GATE_XC1 (2 << 4)
#define ATMEL_TC_GATE_XC2 (3 << 4)
#define ATMEL_TC_WAVE (1 << 15) /* true = Waveform mode */
/* CAPTURE mode CMR bits */
#define ATMEL_TC_LDBSTOP (1 << 6) /* counter stops on RB load */
#define ATMEL_TC_LDBDIS (1 << 7) /* counter disable on RB load */
#define ATMEL_TC_ETRGEDG (3 << 8) /* external trigger edge */
#define ATMEL_TC_ETRGEDG_NONE (0 << 8)
#define ATMEL_TC_ETRGEDG_RISING (1 << 8)
#define ATMEL_TC_ETRGEDG_FALLING (2 << 8)
#define ATMEL_TC_ETRGEDG_BOTH (3 << 8)
#define ATMEL_TC_ABETRG (1 << 10) /* external trigger is TIOA? */
#define ATMEL_TC_CPCTRG (1 << 14) /* RC compare trigger enable */
#define ATMEL_TC_LDRA (3 << 16) /* RA loading edge (of TIOA) */
#define ATMEL_TC_LDRA_NONE (0 << 16)
#define ATMEL_TC_LDRA_RISING (1 << 16)
#define ATMEL_TC_LDRA_FALLING (2 << 16)
#define ATMEL_TC_LDRA_BOTH (3 << 16)
#define ATMEL_TC_LDRB (3 << 18) /* RB loading edge (of TIOA) */
#define ATMEL_TC_LDRB_NONE (0 << 18)
#define ATMEL_TC_LDRB_RISING (1 << 18)
#define ATMEL_TC_LDRB_FALLING (2 << 18)
#define ATMEL_TC_LDRB_BOTH (3 << 18)
/* WAVEFORM mode CMR bits */
#define ATMEL_TC_CPCSTOP (1 << 6) /* RC compare stops counter */
#define ATMEL_TC_CPCDIS (1 << 7) /* RC compare disables counter */
#define ATMEL_TC_EEVTEDG (3 << 8) /* external event edge */
#define ATMEL_TC_EEVTEDG_NONE (0 << 8)
#define ATMEL_TC_EEVTEDG_RISING (1 << 8)
#define ATMEL_TC_EEVTEDG_FALLING (2 << 8)
#define ATMEL_TC_EEVTEDG_BOTH (3 << 8)
#define ATMEL_TC_EEVT (3 << 10) /* external event source */
#define ATMEL_TC_EEVT_TIOB (0 << 10)
#define ATMEL_TC_EEVT_XC0 (1 << 10)
#define ATMEL_TC_EEVT_XC1 (2 << 10)
#define ATMEL_TC_EEVT_XC2 (3 << 10)
#define ATMEL_TC_ENETRG (1 << 12) /* external event is trigger */
#define ATMEL_TC_WAVESEL (3 << 13) /* waveform type */
#define ATMEL_TC_WAVESEL_UP (0 << 13)
#define ATMEL_TC_WAVESEL_UPDOWN (1 << 13)
#define ATMEL_TC_WAVESEL_UP_AUTO (2 << 13)
#define ATMEL_TC_WAVESEL_UPDOWN_AUTO (3 << 13)
#define ATMEL_TC_ACPA (3 << 16) /* RA compare changes TIOA */
#define ATMEL_TC_ACPA_NONE (0 << 16)
#define ATMEL_TC_ACPA_SET (1 << 16)
#define ATMEL_TC_ACPA_CLEAR (2 << 16)
#define ATMEL_TC_ACPA_TOGGLE (3 << 16)
#define ATMEL_TC_ACPC (3 << 18) /* RC compare changes TIOA */
#define ATMEL_TC_ACPC_NONE (0 << 18)
#define ATMEL_TC_ACPC_SET (1 << 18)
#define ATMEL_TC_ACPC_CLEAR (2 << 18)
#define ATMEL_TC_ACPC_TOGGLE (3 << 18)
#define ATMEL_TC_AEEVT (3 << 20) /* external event changes TIOA */
#define ATMEL_TC_AEEVT_NONE (0 << 20)
#define ATMEL_TC_AEEVT_SET (1 << 20)
#define ATMEL_TC_AEEVT_CLEAR (2 << 20)
#define ATMEL_TC_AEEVT_TOGGLE (3 << 20)
#define ATMEL_TC_ASWTRG (3 << 22) /* software trigger changes TIOA */
#define ATMEL_TC_ASWTRG_NONE (0 << 22)
#define ATMEL_TC_ASWTRG_SET (1 << 22)
#define ATMEL_TC_ASWTRG_CLEAR (2 << 22)
#define ATMEL_TC_ASWTRG_TOGGLE (3 << 22)
#define ATMEL_TC_BCPB (3 << 24) /* RB compare changes TIOB */
#define ATMEL_TC_BCPB_NONE (0 << 24)
#define ATMEL_TC_BCPB_SET (1 << 24)
#define ATMEL_TC_BCPB_CLEAR (2 << 24)
#define ATMEL_TC_BCPB_TOGGLE (3 << 24)
#define ATMEL_TC_BCPC (3 << 26) /* RC compare changes TIOB */
#define ATMEL_TC_BCPC_NONE (0 << 26)
#define ATMEL_TC_BCPC_SET (1 << 26)
#define ATMEL_TC_BCPC_CLEAR (2 << 26)
#define ATMEL_TC_BCPC_TOGGLE (3 << 26)
#define ATMEL_TC_BEEVT (3 << 28) /* external event changes TIOB */
#define ATMEL_TC_BEEVT_NONE (0 << 28)
#define ATMEL_TC_BEEVT_SET (1 << 28)
#define ATMEL_TC_BEEVT_CLEAR (2 << 28)
#define ATMEL_TC_BEEVT_TOGGLE (3 << 28)
#define ATMEL_TC_BSWTRG (3 << 30) /* software trigger changes TIOB */
#define ATMEL_TC_BSWTRG_NONE (0 << 30)
#define ATMEL_TC_BSWTRG_SET (1 << 30)
#define ATMEL_TC_BSWTRG_CLEAR (2 << 30)
#define ATMEL_TC_BSWTRG_TOGGLE (3 << 30)
#define ATMEL_TC_CV 0x10 /* counter Value */
#define ATMEL_TC_RA 0x14 /* register A */
#define ATMEL_TC_RB 0x18 /* register B */
#define ATMEL_TC_RC 0x1c /* register C */
#define ATMEL_TC_SR 0x20 /* status (read-only) */
/* Status-only flags */
#define ATMEL_TC_CLKSTA (1 << 16) /* clock enabled */
#define ATMEL_TC_MTIOA (1 << 17) /* TIOA mirror */
#define ATMEL_TC_MTIOB (1 << 18) /* TIOB mirror */
#define ATMEL_TC_IER 0x24 /* interrupt enable (write-only) */
#define ATMEL_TC_IDR 0x28 /* interrupt disable (write-only) */
#define ATMEL_TC_IMR 0x2c /* interrupt mask (read-only) */
/* Status and IRQ flags */
#define ATMEL_TC_COVFS (1 << 0) /* counter overflow */
#define ATMEL_TC_LOVRS (1 << 1) /* load overrun */
#define ATMEL_TC_CPAS (1 << 2) /* RA compare */
#define ATMEL_TC_CPBS (1 << 3) /* RB compare */
#define ATMEL_TC_CPCS (1 << 4) /* RC compare */
#define ATMEL_TC_LDRAS (1 << 5) /* RA loading */
#define ATMEL_TC_LDRBS (1 << 6) /* RB loading */
#define ATMEL_TC_ETRGS (1 << 7) /* external trigger */
#endif