/*********************************************************************
*
* Filename: act200l.c
* Version: 0.8
* Description: Implementation for the ACTiSYS ACT-IR200L dongle
* Status: Experimental.
* Author: SHIMIZU Takuya <tshimizu@ga2.so-net.ne.jp>
* Created at: Fri Aug 3 17:35:42 2001
* Modified at: Fri Aug 17 10:22:40 2001
* Modified by: SHIMIZU Takuya <tshimizu@ga2.so-net.ne.jp>
*
* Copyright (c) 2001 SHIMIZU Takuya, All Rights Reserved.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
********************************************************************/
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/init.h>
#include <net/irda/irda.h>
#include "sir-dev.h"
static int act200l_reset(struct sir_dev *dev);
static int act200l_open(struct sir_dev *dev);
static int act200l_close(struct sir_dev *dev);
static int act200l_change_speed(struct sir_dev *dev, unsigned speed);
/* Regsiter 0: Control register #1 */
#define ACT200L_REG0 0x00
#define ACT200L_TXEN 0x01 /* Enable transmitter */
#define ACT200L_RXEN 0x02 /* Enable receiver */
/* Register 1: Control register #2 */
#define ACT200L_REG1 0x10
#define ACT200L_LODB 0x01 /* Load new baud rate count value */
#define ACT200L_WIDE 0x04 /* Expand the maximum allowable pulse */
/* Register 4: Output Power register */
#define ACT200L_REG4 0x40
#define ACT200L_OP0 0x01 /* Enable LED1C output */
#define ACT200L_OP1 0x02 /* Enable LED2C output */
#define ACT200L_BLKR 0x04
/* Register 5: Receive Mode register */
#define ACT200L_REG5 0x50
#define ACT200L_RWIDL 0x01 /* fixed 1.6us pulse mode */
/* Register 6: Receive Sensitivity register #1 */
#define ACT200L_REG6 0x60
#define ACT200L_RS0 0x01 /* receive threshold bit 0 */
#define ACT200L_RS1 0x02 /* receive threshold bit 1 */
/* Register 7: Receive Sensitivity register #2 */
#define ACT200L_REG7 0x70
#define ACT200L_ENPOS 0x04 /* Ignore the falling edge */
/* Register 8,9: Baud Rate Dvider register #1,#2 */
#define ACT200L_REG8 0x80
#define ACT200L_REG9 0x90
#define ACT200L_2400 0x5f
#define ACT200L_9600 0x17
#define ACT200L_19200 0x0b
#define ACT200L_38400 0x05
#define ACT200L_57600 0x03
#define ACT200L_115200 0x01
/* Register 13: Control register #3 */
#define ACT200L_REG13 0xd0
#define ACT200L_SHDW 0x01 /* Enable access to shadow registers */
/* Register 15: Status register */
#define ACT200L_REG15 0xf0
/* Register 21: Control register #4 */
#define ACT200L_REG21 0x50
#define ACT200L_EXCK 0x02 /* Disable clock output driver */
#define ACT200L_OSCL 0x04 /* oscillator in low power, medium accuracy mode */
static struct dongle_driver act200l = {
.owner = THIS_MODULE,
.driver_name = "ACTiSYS ACT-IR200L",
.type = IRDA_ACT200L_DONGLE,
.open = act200l_open,
.close = act200l_close,
.reset = act200l_reset,
.set_speed = act200l_change_speed,
};
static int __init act200l_sir_init(void)
{
return irda_register_dongle(&act200l);
}
static void __exit act200l_sir_cleanup(void)
{
irda_unregister_dongle(&act200l);
}
static int act200l_open(struct sir_dev *dev)
{
struct qos_info *qos = &dev->qos;
IRDA_DEBUG(2, "%s()\n", __func__ );
/* Power on the dongle */
sirdev_set_dtr_rts(dev, TRUE, TRUE);
/* Set the speeds we can accept */
qos->baud_rate.bits &= IR_9600|IR_19200|IR_38400|IR_57600|IR_115200;
qos->min_turn_time.bits = 0x03;
irda_qos_bits_to_value(qos);
/* irda thread waits 50 msec for power settling */
return 0;
}
static int act200l_close(struct sir_dev *dev)
{
IRDA_DEBUG(2, "%s()\n", __func__ );
/* Power off the dongle */
sirdev_set_dtr_rts(dev, FALSE, FALSE);
return 0;
}
/*
* Function act200l_change_speed (dev, speed)
*
* Set the speed for the ACTiSYS ACT-IR200L type dongle.
*
*/
static int act200l_change_speed(struct sir_dev *dev, unsigned speed)
{
u8 control[3];
int ret = 0;
IRDA_DEBUG(2, "%s()\n", __func__ );
/* Clear DTR and set RTS to enter command mode */
sirdev_set_dtr_rts(dev, FALSE, TRUE);
switch (speed) {
default:
ret = -EINVAL;
/* fall through */
case 9600:
control[0] = ACT200L_REG8 | (ACT200L_9600 & 0x0f);
control[1] = ACT200L_REG9 | ((ACT200L_9600 >> 4) & 0x0f);
break;
case 19200:
control[0] = ACT200L_REG8 | (ACT200L_19200 & 0x0f);
control[1] = ACT200L_REG9 | ((ACT200L_19200 >> 4) & 0x0f);
break;
case 38400:
control[0] = ACT200L_REG8 | (ACT200L_38400 & 0x0f);
control[1] = ACT200L_REG9 | ((ACT200L_38400 >> 4) & 0x0f);
break;
case 57600:
control[0] = ACT200L_REG8 | (ACT200L_57600 & 0x0f);
control[1] = ACT200L_REG9 | ((ACT200L_57600 >> 4) & 0x0f);
break;
case 115200:
control[0] = ACT200L_REG8 | (ACT200L_115200 & 0x0f);
control[1] = ACT200L_REG9 | ((ACT200L_115200 >> 4) & 0x0f);
break;
}
control[2] = ACT200L_REG1 | ACT200L_LODB | ACT200L_WIDE;
/* Write control bytes */
sirdev_raw_write(dev, control, 3);
msleep(5);
/* Go back to normal mode */
sirdev_set_dtr_rts(dev, TRUE, TRUE);
dev->speed = speed;
return ret;
}
/*
* Function act200l_reset (driver)
*
* Reset the ACTiSYS ACT-IR200L type dongle.
*/
#define ACT200L_STATE_WAIT1_RESET (SIRDEV_STATE_DONGLE_RESET+1)
#define ACT200L_STATE_WAIT2_RESET (SIRDEV_STATE_DONGLE_RESET+2)
static int act200l_reset(struct sir_dev *dev)
{
unsigned state = dev->fsm.substate;
unsigned delay = 0;
static const u8 control[9] = {
ACT200L_REG15,
ACT200L_REG13 | ACT200L_SHDW,
ACT200L_REG21 | ACT200L_EXCK | ACT200L_OSCL,
ACT200L_REG13,
ACT200L_REG7 | ACT200L_ENPOS,
ACT200L_REG6 | ACT200L_RS0 | ACT200L_RS1,
ACT200L_REG5 | ACT200L_RWIDL,
ACT200L_REG4 | ACT200L_OP0 | ACT200L_OP1 | ACT200L_BLKR,
ACT200L_REG0 | ACT200L_TXEN | ACT200L_RXEN
};
int ret = 0;
IRDA_DEBUG(2, "%s()\n", __func__ );
switch (state) {
case SIRDEV_STATE_DONGLE_RESET:
/* Reset the dongle : set RTS low for 25 ms */
sirdev_set_dtr_rts(dev, TRUE, FALSE);
state = ACT200L_STATE_WAIT1_RESET;
delay = 50;
break;
case ACT200L_STATE_WAIT1_RESET:
/* Clear DTR and set RTS to enter command mode */
sirdev_set_dtr_rts(dev, FALSE, TRUE);
udelay(25); /* better wait for some short while */
/* Write control bytes */
sirdev_raw_write(dev, control, sizeof(control));
state = ACT200L_STATE_WAIT2_RESET;
delay = 15;
break;
case ACT200L_STATE_WAIT2_RESET:
/* Go back to normal mode */
sirdev_set_dtr_rts(dev, TRUE, TRUE);
dev->speed = 9600;
break;
default:
IRDA_ERROR("%s(), unknown state %d\n", __func__, state);
ret = -1;
break;
}
dev->fsm.substate = state;
return (delay > 0) ? delay : ret;
}
MODULE_AUTHOR("SHIMIZU Takuya <tshimizu@ga2.so-net.ne.jp>");
MODULE_DESCRIPTION("ACTiSYS ACT-IR200L dongle driver");
MODULE_LICENSE("GPL");
MODULE_ALIAS("irda-dongle-10"); /* IRDA_ACT200L_DONGLE */
module_init(act200l_sir_init);
module_exit(act200l_sir_cleanup);