/* Linux header file for the ATP pocket ethernet adapter. */
/* v1.09 8/9/2000 becker@scyld.com. */
#include <linux/if_ether.h>
#include <linux/types.h>
/* The header prepended to received packets. */
struct rx_header {
ushort pad; /* Pad. */
ushort rx_count;
ushort rx_status; /* Unknown bit assignments :-<. */
ushort cur_addr; /* Apparently the current buffer address(?) */
};
#define PAR_DATA 0
#define PAR_STATUS 1
#define PAR_CONTROL 2
#define Ctrl_LNibRead 0x08 /* LP_PSELECP */
#define Ctrl_HNibRead 0
#define Ctrl_LNibWrite 0x08 /* LP_PSELECP */
#define Ctrl_HNibWrite 0
#define Ctrl_SelData 0x04 /* LP_PINITP */
#define Ctrl_IRQEN 0x10 /* LP_PINTEN */
#define EOW 0xE0
#define EOC 0xE0
#define WrAddr 0x40 /* Set address of EPLC read, write register. */
#define RdAddr 0xC0
#define HNib 0x10
enum page0_regs
{
/* The first six registers hold the ethernet physical station address. */
PAR0 = 0, PAR1 = 1, PAR2 = 2, PAR3 = 3, PAR4 = 4, PAR5 = 5,
TxCNT0 = 6, TxCNT1 = 7, /* The transmit byte count. */
TxSTAT = 8, RxSTAT = 9, /* Tx and Rx status. */
ISR = 10, IMR = 11, /* Interrupt status and mask. */
CMR1 = 12, /* Command register 1. */
CMR2 = 13, /* Command register 2. */
MODSEL = 14, /* Mode select register. */
MAR = 14, /* Memory address register (?). */
CMR2_h = 0x1d, };
enum eepage_regs
{ PROM_CMD = 6, PROM_DATA = 7 }; /* Note that PROM_CMD is in the "high" bits. */
#define ISR_TxOK 0x01
#define ISR_RxOK 0x04
#define ISR_TxErr 0x02
#define ISRh_RxErr 0x11 /* ISR, high nibble */
#define CMR1h_MUX 0x08 /* Select printer multiplexor on 8012. */
#define CMR1h_RESET 0x04 /* Reset. */
#define CMR1h_RxENABLE 0x02 /* Rx unit enable. */
#define CMR1h_TxENABLE 0x01 /* Tx unit enable. */
#define CMR1h_TxRxOFF 0x00
#define CMR1_ReXmit 0x08 /* Trigger a retransmit. */
#define CMR1_Xmit 0x04 /* Trigger a transmit. */
#define CMR1_IRQ 0x02 /* Interrupt active. */
#define CMR1_BufEnb 0x01 /* Enable the buffer(?). */
#define CMR1_NextPkt 0x01 /* Enable the buffer(?). */
#define CMR2_NULL 8
#define CMR2_IRQOUT 9
#define CMR2_RAMTEST 10
#define CMR2_EEPROM 12 /* Set to page 1, for reading the EEPROM. */
#define CMR2h_OFF 0 /* No accept mode. */
#define CMR2h_Physical 1 /* Accept a physical address match only. */
#define CMR2h_Normal 2 /* Accept physical and broadcast address. */
#define CMR2h_PROMISC 3 /* Promiscuous mode. */
/* An inline function used below: it differs from inb() by explicitly return an unsigned
char, saving a truncation. */
static inline unsigned char inbyte(unsigned short port)
{
unsigned char _v;
__asm__ __volatile__ ("inb %w1,%b0" :"=a" (_v):"d" (port));
return _v;
}
/* Read register OFFSET.
This command should always be terminated with read_end(). */
static inline unsigned char read_nibble(short port, unsigned char offset)
{
unsigned char retval;
outb(EOC+offset, port + PAR_DATA);
outb(RdAddr+offset, port + PAR_DATA);
inbyte(port + PAR_STATUS); /* Settling time delay */
retval = inbyte(port + PAR_STATUS);
outb(EOC+offset, port + PAR_DATA);
return retval;
}
/* Functions for bulk data read. The interrupt line is always disabled. */
/* Get a byte using read mode 0, reading data from the control lines. */
static inline unsigned char read_byte_mode0(short ioaddr)
{
unsigned char low_nib;
outb(Ctrl_LNibRead, ioaddr + PAR_CONTROL);
inbyte(ioaddr + PAR_STATUS);
low_nib = (inbyte(ioaddr + PAR_STATUS) >> 3) & 0x0f;
outb(Ctrl_HNibRead, ioaddr + PAR_CONTROL);
inbyte(ioaddr + PAR_STATUS); /* Settling time delay -- needed! */
inbyte(ioaddr + PAR_STATUS); /* Settling time delay -- needed! */
return low_nib | ((inbyte(ioaddr + PAR_STATUS) << 1) & 0xf0);
}
/* The same as read_byte_mode0(), but does multiple inb()s for stability. */
static inline unsigned char read_byte_mode2(short ioaddr)
{
unsigned char low_nib;
outb(Ctrl_LNibRead, ioaddr + PAR_CONTROL);
inbyte(ioaddr + PAR_STATUS);
low_nib = (inbyte(ioaddr + PAR_STATUS) >> 3) & 0x0f;
outb(Ctrl_HNibRead, ioaddr + PAR_CONTROL);
inbyte(ioaddr + PAR_STATUS); /* Settling time delay -- needed! */
return low_nib | ((inbyte(ioaddr + PAR_STATUS) << 1) & 0xf0);
}
/* Read a byte through the data register. */
static inline unsigned char read_byte_mode4(short ioaddr)
{
unsigned char low_nib;
outb(RdAddr | MAR, ioaddr + PAR_DATA);
low_nib = (inbyte(ioaddr + PAR_STATUS) >> 3) & 0x0f;
outb(RdAddr | HNib | MAR, ioaddr + PAR_DATA);
return low_nib | ((inbyte(ioaddr + PAR_STATUS) << 1) & 0xf0);
}
/* Read a byte through the data register, double reading to allow settling. */
static inline unsigned char read_byte_mode6(short ioaddr)
{
unsigned char low_nib;
outb(RdAddr | MAR, ioaddr + PAR_DATA);
inbyte(ioaddr + PAR_STATUS);
low_nib = (inbyte(ioaddr + PAR_STATUS) >> 3) & 0x0f;
outb(RdAddr | HNib | MAR, ioaddr + PAR_DATA);
inbyte(ioaddr + PAR_STATUS);
return low_nib | ((inbyte(ioaddr + PAR_STATUS) << 1) & 0xf0);
}
static inline void
write_reg(short port, unsigned char reg, unsigned char value)
{
unsigned char outval;
outb(EOC | reg, port + PAR_DATA);
outval = WrAddr | reg;
outb(outval, port + PAR_DATA);
outb(outval, port + PAR_DATA); /* Double write for PS/2. */
outval &= 0xf0;
outval |= value;
outb(outval, port + PAR_DATA);
outval &= 0x1f;
outb(outval, port + PAR_DATA);
outb(outval, port + PAR_DATA);
outb(EOC | outval, port + PAR_DATA);
}
static inline void
write_reg_high(short port, unsigned char reg, unsigned char value)
{
unsigned char outval = EOC | HNib | reg;
outb(outval, port + PAR_DATA);
outval &= WrAddr | HNib | 0x0f;
outb(outval, port + PAR_DATA);
outb(outval, port + PAR_DATA); /* Double write for PS/2. */
outval = WrAddr | HNib | value;
outb(outval, port + PAR_DATA);
outval &= HNib | 0x0f; /* HNib | value */
outb(outval, port + PAR_DATA);
outb(outval, port + PAR_DATA);
outb(EOC | HNib | outval, port + PAR_DATA);
}
/* Write a byte out using nibble mode. The low nibble is written first. */
static inline void
write_reg_byte(short port, unsigned char reg, unsigned char value)
{
unsigned char outval;
outb(EOC | reg, port + PAR_DATA); /* Reset the address register. */
outval = WrAddr | reg;
outb(outval, port + PAR_DATA);
outb(outval, port + PAR_DATA); /* Double write for PS/2. */
outb((outval & 0xf0) | (value & 0x0f), port + PAR_DATA);
outb(value & 0x0f, port + PAR_DATA);
value >>= 4;
outb(value, port + PAR_DATA);
outb(0x10 | value, port + PAR_DATA);
outb(0x10 | value, port + PAR_DATA);
outb(EOC | value, port + PAR_DATA); /* Reset the address register. */
}
/*
* Bulk data writes to the packet buffer. The interrupt line remains enabled.
* The first, faster method uses only the dataport (data modes 0, 2 & 4).
* The second (backup) method uses data and control regs (modes 1, 3 & 5).
* It should only be needed when there is skew between the individual data
* lines.
*/
static inline void write_byte_mode0(short ioaddr, unsigned char value)
{
outb(value & 0x0f, ioaddr + PAR_DATA);
outb((value>>4) | 0x10, ioaddr + PAR_DATA);
}
static inline void write_byte_mode1(short ioaddr, unsigned char value)
{
outb(value & 0x0f, ioaddr + PAR_DATA);
outb(Ctrl_IRQEN | Ctrl_LNibWrite, ioaddr + PAR_CONTROL);
outb((value>>4) | 0x10, ioaddr + PAR_DATA);
outb(Ctrl_IRQEN | Ctrl_HNibWrite, ioaddr + PAR_CONTROL);
}
/* Write 16bit VALUE to the packet buffer: the same as above just doubled. */
static inline void write_word_mode0(short ioaddr, unsigned short value)
{
outb(value & 0x0f, ioaddr + PAR_DATA);
value >>= 4;
outb((value & 0x0f) | 0x10, ioaddr + PAR_DATA);
value >>= 4;
outb(value & 0x0f, ioaddr + PAR_DATA);
value >>= 4;
outb((value & 0x0f) | 0x10, ioaddr + PAR_DATA);
}
/* EEPROM_Ctrl bits. */
#define EE_SHIFT_CLK 0x04 /* EEPROM shift clock. */
#define EE_CS 0x02 /* EEPROM chip select. */
#define EE_CLK_HIGH 0x12
#define EE_CLK_LOW 0x16
#define EE_DATA_WRITE 0x01 /* EEPROM chip data in. */
#define EE_DATA_READ 0x08 /* EEPROM chip data out. */
/* Delay between EEPROM clock transitions. */
#define eeprom_delay(ticks) \
do { int _i = 40; while (--_i > 0) { __SLOW_DOWN_IO; }} while (0)
/* The EEPROM commands include the alway-set leading bit. */
#define EE_WRITE_CMD(offset) (((5 << 6) + (offset)) << 17)
#define EE_READ(offset) (((6 << 6) + (offset)) << 17)
#define EE_ERASE(offset) (((7 << 6) + (offset)) << 17)
#define EE_CMD_SIZE 27 /* The command+address+data size. */