/*
* P1025 TWR Device Tree Source stub (no addresses or top-level ranges)
*
* Copyright 2013 Freescale Semiconductor Inc.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
* * Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* * Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* * Neither the name of Freescale Semiconductor nor the
* names of its contributors may be used to endorse or promote products
* derived from this software without specific prior written permission.
*
*
* ALTERNATIVELY, this software may be distributed under the terms of the
* GNU General Public License ("GPL") as published by the Free Software
* Foundation, either version 2 of that License or (at your option) any
* later version.
*
* THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
* EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
* DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
/{
aliases {
ethernet3 = &enet3;
ethernet4 = &enet4;
};
};
&lbc {
nor@0,0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "cfi-flash";
reg = <0x0 0x0 0x4000000>;
bank-width = <2>;
device-width = <1>;
partition@0 {
/* This location must not be altered */
/* 256KB for Vitesse 7385 Switch firmware */
reg = <0x0 0x00040000>;
label = "NOR Vitesse-7385 Firmware";
read-only;
};
partition@40000 {
/* 256KB for DTB Image */
reg = <0x00040000 0x00040000>;
label = "NOR DTB Image";
};
partition@80000 {
/* 5.5 MB for Linux Kernel Image */
reg = <0x00080000 0x00580000>;
label = "NOR Linux Kernel Image";
};
partition@400000 {
/* 56.75MB for Root file System */
reg = <0x00600000 0x038c0000>;
label = "NOR Root File System";
};
partition@ec0000 {
/* This location must not be altered */
/* 256KB for QE ucode firmware*/
reg = <0x03ec0000 0x00040000>;
label = "NOR QE microcode firmware";
read-only;
};
partition@f00000 {
/* This location must not be altered */
/* 512KB for u-boot Bootloader Image */
/* 512KB for u-boot Environment Variables */
reg = <0x03f00000 0x00100000>;
label = "NOR U-Boot Image";
read-only;
};
};
/* CS2 for Display */
display@2,0 {
compatible = "solomon,ssd1289fb";
reg = <0x2 0x0000 0x0004>;
};
};
&soc {
usb@22000 {
phy_type = "ulpi";
};
mdio@24000 {
phy0: ethernet-phy@2 {
interrupt-parent = <&mpic>;
interrupts = <1 1 0 0>;
reg = <0x2>;
};
phy1: ethernet-phy@1 {
interrupt-parent = <&mpic>;
interrupts = <2 1 0 0>;
reg = <0x1>;
};
tbi0: tbi-phy@11 {
reg = <0x11>;
device_type = "tbi-phy";
};
};
mdio@25000 {
tbi1: tbi-phy@11 {
reg = <0x11>;
device_type = "tbi-phy";
};
};
mdio@26000 {
tbi2: tbi-phy@11 {
reg = <0x11>;
device_type = "tbi-phy";
};
};
enet0: ethernet@b0000 {
phy-handle = <&phy0>;
phy-connection-type = "rgmii-id";
};
enet1: ethernet@b1000 {
status = "disabled";
};
enet2: ethernet@b2000 {
phy-handle = <&phy1>;
phy-connection-type = "rgmii-id";
};
par_io@e0100 {
#address-cells = <1>;
#size-cells = <1>;
reg = <0xe0100 0x60>;
ranges = <0x0 0xe0100 0x60>;
device_type = "par_io";
num-ports = <3>;
pio1: ucc_pin@01 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
0x1 0x13 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */
0x1 0x14 0x3 0x0 0x1 0x0 /* QE_MUX_MDIO */
0x0 0x17 0x2 0x0 0x2 0x0 /* CLK12 */
0x0 0x18 0x2 0x0 0x1 0x0 /* CLK9 */
0x0 0x7 0x1 0x0 0x2 0x0 /* ENET1_TXD0_SER1_TXD0 */
0x0 0x9 0x1 0x0 0x2 0x0 /* ENET1_TXD1_SER1_TXD1 */
0x0 0xb 0x1 0x0 0x2 0x0 /* ENET1_TXD2_SER1_TXD2 */
0x0 0xc 0x1 0x0 0x2 0x0 /* ENET1_TXD3_SER1_TXD3 */
0x0 0x6 0x2 0x0 0x2 0x0 /* ENET1_RXD0_SER1_RXD0 */
0x0 0xa 0x2 0x0 0x2 0x0 /* ENET1_RXD1_SER1_RXD1 */
0x0 0xe 0x2 0x0 0x2 0x0 /* ENET1_RXD2_SER1_RXD2 */
0x0 0xf 0x2 0x0 0x2 0x0 /* ENET1_RXD3_SER1_RXD3 */
0x0 0x5 0x1 0x0 0x2 0x0 /* ENET1_TX_EN_SER1_RTS_B */
0x0 0xd 0x1 0x0 0x2 0x0 /* ENET1_TX_ER */
0x0 0x4 0x2 0x0 0x2 0x0 /* ENET1_RX_DV_SER1_CTS_B */
0x0 0x8 0x2 0x0 0x2 0x0 /* ENET1_RX_ER_SER1_CD_B */
0x0 0x11 0x2 0x0 0x2 0x0 /* ENET1_CRS */
0x0 0x10 0x2 0x0 0x2 0x0>; /* ENET1_COL */
};
pio2: ucc_pin@02 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
0x1 0x13 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */
0x1 0x14 0x3 0x0 0x1 0x0 /* QE_MUX_MDIO */
0x1 0xb 0x2 0x0 0x1 0x0 /* CLK13 */
0x1 0x7 0x1 0x0 0x2 0x0 /* ENET5_TXD0_SER5_TXD0 */
0x1 0xa 0x1 0x0 0x2 0x0 /* ENET5_TXD1_SER5_TXD1 */
0x1 0x6 0x2 0x0 0x2 0x0 /* ENET5_RXD0_SER5_RXD0 */
0x1 0x9 0x2 0x0 0x2 0x0 /* ENET5_RXD1_SER5_RXD1 */
0x1 0x5 0x1 0x0 0x2 0x0 /* ENET5_TX_EN_SER5_RTS_B */
0x1 0x4 0x2 0x0 0x2 0x0 /* ENET5_RX_DV_SER5_CTS_B */
0x1 0x8 0x2 0x0 0x2 0x0>; /* ENET5_RX_ER_SER5_CD_B */
};
pio3: ucc_pin@03 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
0x0 0x16 0x2 0x0 0x2 0x0 /* SER7_CD_B*/
0x0 0x12 0x2 0x0 0x2 0x0 /* SER7_CTS_B*/
0x0 0x13 0x1 0x0 0x2 0x0 /* SER7_RTS_B*/
0x0 0x14 0x2 0x0 0x2 0x0 /* SER7_RXD0*/
0x0 0x15 0x1 0x0 0x2 0x0>; /* SER7_TXD0*/
};
pio4: ucc_pin@04 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
0x1 0x0 0x2 0x0 0x2 0x0 /* SER3_CD_B*/
0x0 0x1c 0x2 0x0 0x2 0x0 /* SER3_CTS_B*/
0x0 0x1d 0x1 0x0 0x2 0x0 /* SER3_RTS_B*/
0x0 0x1e 0x2 0x0 0x2 0x0 /* SER3_RXD0*/
0x0 0x1f 0x1 0x0 0x2 0x0>; /* SER3_TXD0*/
};
};
};
&qe {
enet3: ucc@2000 {
device_type = "network";
compatible = "ucc_geth";
rx-clock-name = "clk12";
tx-clock-name = "clk9";
pio-handle = <&pio1>;
phy-handle = <&qe_phy0>;
phy-connection-type = "mii";
};
mdio@2120 {
qe_phy0: ethernet-phy@18 {
interrupt-parent = <&mpic>;
interrupts = <4 1 0 0>;
reg = <0x18>;
device_type = "ethernet-phy";
};
qe_phy1: ethernet-phy@19 {
interrupt-parent = <&mpic>;
interrupts = <5 1 0 0>;
reg = <0x19>;
device_type = "ethernet-phy";
};
tbi-phy@11 {
reg = <0x11>;
device_type = "tbi-phy";
};
};
enet4: ucc@2400 {
device_type = "network";
compatible = "ucc_geth";
rx-clock-name = "none";
tx-clock-name = "clk13";
pio-handle = <&pio2>;
phy-handle = <&qe_phy1>;
phy-connection-type = "rmii";
};
serial2: ucc@2600 {
device_type = "serial";
compatible = "ucc_uart";
port-number = <0>;
rx-clock-name = "brg6";
tx-clock-name = "brg6";
pio-handle = <&pio3>;
};
serial3: ucc@2200 {
device_type = "serial";
compatible = "ucc_uart";
port-number = <1>;
rx-clock-name = "brg2";
tx-clock-name = "brg2";
pio-handle = <&pio4>;
};
};