- 根目录:
- arch
- arm
- mach-u300
- include
- mach
- u300-regs.h
/*
*
* arch/arm/mach-u300/include/mach/u300-regs.h
*
*
* Copyright (C) 2006-2009 ST-Ericsson AB
* License terms: GNU General Public License (GPL) version 2
* Basic register address definitions in physical memory and
* some block definitions for core devices like the timer.
* Author: Linus Walleij <linus.walleij@stericsson.com>
*/
#ifndef __MACH_U300_REGS_H
#define __MACH_U300_REGS_H
/*
* These are the large blocks of memory allocated for I/O.
* the defines are used for setting up the I/O memory mapping.
*/
/* NAND Flash CS0 */
#define U300_NAND_CS0_PHYS_BASE 0x80000000
/* NFIF */
#define U300_NAND_IF_PHYS_BASE 0x9f800000
/* ALE, CLE offset for FSMC NAND */
#define PLAT_NAND_CLE (1 << 16)
#define PLAT_NAND_ALE (1 << 17)
/* AHB Peripherals */
#define U300_AHB_PER_PHYS_BASE 0xa0000000
#define U300_AHB_PER_VIRT_BASE 0xff010000
/* FAST Peripherals */
#define U300_FAST_PER_PHYS_BASE 0xc0000000
#define U300_FAST_PER_VIRT_BASE 0xff020000
/* SLOW Peripherals */
#define U300_SLOW_PER_PHYS_BASE 0xc0010000
#define U300_SLOW_PER_VIRT_BASE 0xff000000
/* Boot ROM */
#define U300_BOOTROM_PHYS_BASE 0xffff0000
#define U300_BOOTROM_VIRT_BASE 0xffff0000
/* SEMI config base */
#define U300_SEMI_CONFIG_BASE 0x2FFE0000
/*
* AHB peripherals
*/
/* AHB Peripherals Bridge Controller */
#define U300_AHB_BRIDGE_BASE (U300_AHB_PER_PHYS_BASE+0x0000)
/* Vectored Interrupt Controller 0, servicing 32 interrupts */
#define U300_INTCON0_BASE (U300_AHB_PER_PHYS_BASE+0x1000)
#define U300_INTCON0_VBASE IOMEM(U300_AHB_PER_VIRT_BASE+0x1000)
/* Vectored Interrupt Controller 1, servicing 32 interrupts */
#define U300_INTCON1_BASE (U300_AHB_PER_PHYS_BASE+0x2000)
#define U300_INTCON1_VBASE IOMEM(U300_AHB_PER_VIRT_BASE+0x2000)
/* Memory Stick Pro (MSPRO) controller */
#define U300_MSPRO_BASE (U300_AHB_PER_PHYS_BASE+0x3000)
/* EMIF Configuration Area */
#define U300_EMIF_CFG_BASE (U300_AHB_PER_PHYS_BASE+0x4000)
/*
* FAST peripherals
*/
/* FAST bridge control */
#define U300_FAST_BRIDGE_BASE (U300_FAST_PER_PHYS_BASE+0x0000)
/* MMC/SD controller */
#define U300_MMCSD_BASE (U300_FAST_PER_PHYS_BASE+0x1000)
/* PCM I2S0 controller */
#define U300_PCM_I2S0_BASE (U300_FAST_PER_PHYS_BASE+0x2000)
/* PCM I2S1 controller */
#define U300_PCM_I2S1_BASE (U300_FAST_PER_PHYS_BASE+0x3000)
/* I2C0 controller */
#define U300_I2C0_BASE (U300_FAST_PER_PHYS_BASE+0x4000)
/* I2C1 controller */
#define U300_I2C1_BASE (U300_FAST_PER_PHYS_BASE+0x5000)
/* SPI controller */
#define U300_SPI_BASE (U300_FAST_PER_PHYS_BASE+0x6000)
/* Fast UART1 on U335 only */
#define U300_UART1_BASE (U300_FAST_PER_PHYS_BASE+0x7000)
/*
* SLOW peripherals
*/
/* SLOW bridge control */
#define U300_SLOW_BRIDGE_BASE (U300_SLOW_PER_PHYS_BASE)
/* SYSCON */
#define U300_SYSCON_BASE (U300_SLOW_PER_PHYS_BASE+0x1000)
#define U300_SYSCON_VBASE IOMEM(U300_SLOW_PER_VIRT_BASE+0x1000)
/* Watchdog */
#define U300_WDOG_BASE (U300_SLOW_PER_PHYS_BASE+0x2000)
/* UART0 */
#define U300_UART0_BASE (U300_SLOW_PER_PHYS_BASE+0x3000)
/* APP side special timer */
#define U300_TIMER_APP_BASE (U300_SLOW_PER_PHYS_BASE+0x4000)
#define U300_TIMER_APP_VBASE IOMEM(U300_SLOW_PER_VIRT_BASE+0x4000)
/* Keypad */
#define U300_KEYPAD_BASE (U300_SLOW_PER_PHYS_BASE+0x5000)
/* GPIO */
#define U300_GPIO_BASE (U300_SLOW_PER_PHYS_BASE+0x6000)
/* RTC */
#define U300_RTC_BASE (U300_SLOW_PER_PHYS_BASE+0x7000)
/* Bus tracer */
#define U300_BUSTR_BASE (U300_SLOW_PER_PHYS_BASE+0x8000)
/* Event handler (hardware queue) */
#define U300_EVHIST_BASE (U300_SLOW_PER_PHYS_BASE+0x9000)
/* Genric Timer */
#define U300_TIMER_BASE (U300_SLOW_PER_PHYS_BASE+0xa000)
/* PPM */
#define U300_PPM_BASE (U300_SLOW_PER_PHYS_BASE+0xb000)
/*
* REST peripherals
*/
/* ISP (image signal processor) */
#define U300_ISP_BASE (0xA0008000)
/* DMA Controller base */
#define U300_DMAC_BASE (0xC0020000)
/* MSL Base */
#define U300_MSL_BASE (0xc0022000)
/* APEX Base */
#define U300_APEX_BASE (0xc0030000)
/* Video Encoder Base */
#define U300_VIDEOENC_BASE (0xc0080000)
/* XGAM Base */
#define U300_XGAM_BASE (0xd0000000)
#endif