- 根目录:
- drivers
- staging
- rtl8192u
- r8192U_core.c
C++程序
|
6051行
|
169.55 KB
/******************************************************************************
* Copyright(c) 2008 - 2010 Realtek Corporation. All rights reserved.
* Linux device driver for RTL8192U
*
* Based on the r8187 driver, which is:
* Copyright 2004-2005 Andrea Merello <andreamrl@tiscali.it>, et al.
* This program is free software; you can redistribute it and/or modify it
* under the terms of version 2 of the GNU General Public License as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
* more details.
*
* You should have received a copy of the GNU General Public License along with
* this program; if not, write to the Free Software Foundation, Inc.,
* 51 Franklin Street, Fifth Floor, Boston, MA 02110, USA
*
* The full GNU General Public License is included in this distribution in the
* file called LICENSE.
*
* Contact Information:
* Jerry chuang <wlanfae@realtek.com>
*/
#ifndef CONFIG_FORCE_HARD_FLOAT
double __floatsidf (int i) { return i; }
unsigned int __fixunsdfsi (double d) { return d; }
double __adddf3(double a, double b) { return a+b; }
double __addsf3(float a, float b) { return a+b; }
double __subdf3(double a, double b) { return a-b; }
double __extendsfdf2(float a) {return a;}
#endif
#undef LOOP_TEST
#undef DUMP_RX
#undef DUMP_TX
#undef DEBUG_TX_DESC2
#undef RX_DONT_PASS_UL
#undef DEBUG_EPROM
#undef DEBUG_RX_VERBOSE
#undef DUMMY_RX
#undef DEBUG_ZERO_RX
#undef DEBUG_RX_SKB
#undef DEBUG_TX_FRAG
#undef DEBUG_RX_FRAG
#undef DEBUG_TX_FILLDESC
#undef DEBUG_TX
#undef DEBUG_IRQ
#undef DEBUG_RX
#undef DEBUG_RXALLOC
#undef DEBUG_REGISTERS
#undef DEBUG_RING
#undef DEBUG_IRQ_TASKLET
#undef DEBUG_TX_ALLOC
#undef DEBUG_TX_DESC
#define CONFIG_RTL8192_IO_MAP
#include <asm/uaccess.h>
#include "r8192U_hw.h"
#include "r8192U.h"
#include "r8190_rtl8256.h" /* RTL8225 Radio frontend */
#include "r8180_93cx6.h" /* Card EEPROM */
#include "r8192U_wx.h"
#include "r819xU_phy.h" //added by WB 4.30.2008
#include "r819xU_phyreg.h"
#include "r819xU_cmdpkt.h"
#include "r8192U_dm.h"
//#include "r8192xU_phyreg.h"
#include <linux/usb.h>
#include <linux/slab.h>
// FIXME: check if 2.6.7 is ok
#ifdef CONFIG_RTL8192_PM
#include "r8192_pm.h"
#endif
#include "dot11d.h"
//set here to open your trace code. //WB
u32 rt_global_debug_component = \
// COMP_INIT |
// COMP_DBG |
// COMP_EPROM |
// COMP_PHY |
// COMP_RF |
// COMP_FIRMWARE |
// COMP_CH |
// COMP_POWER_TRACKING |
// COMP_RATE |
// COMP_TXAGC |
// COMP_TRACE |
COMP_DOWN |
// COMP_RECV |
// COMP_SWBW |
COMP_SEC |
// COMP_RESET |
// COMP_SEND |
// COMP_EVENTS |
COMP_ERR ; //always open err flags on
#define TOTAL_CAM_ENTRY 32
#define CAM_CONTENT_COUNT 8
static const struct usb_device_id rtl8192_usb_id_tbl[] = {
/* Realtek */
{USB_DEVICE(0x0bda, 0x8192)},
{USB_DEVICE(0x0bda, 0x8709)},
/* Corega */
{USB_DEVICE(0x07aa, 0x0043)},
/* Belkin */
{USB_DEVICE(0x050d, 0x805E)},
/* Sitecom */
{USB_DEVICE(0x0df6, 0x0031)},
/* EnGenius */
{USB_DEVICE(0x1740, 0x9201)},
/* Dlink */
{USB_DEVICE(0x2001, 0x3301)},
/* Zinwell */
{USB_DEVICE(0x5a57, 0x0290)},
/* LG */
{USB_DEVICE(0x043e, 0x7a01)},
{}
};
MODULE_LICENSE("GPL");
MODULE_VERSION("V 1.1");
MODULE_DEVICE_TABLE(usb, rtl8192_usb_id_tbl);
MODULE_DESCRIPTION("Linux driver for Realtek RTL8192 USB WiFi cards");
static char* ifname = "wlan%d";
static int hwwep = 1; //default use hw. set 0 to use software security
static int channels = 0x3fff;
module_param(ifname, charp, S_IRUGO|S_IWUSR );
//module_param(hwseqnum,int, S_IRUGO|S_IWUSR);
module_param(hwwep,int, S_IRUGO|S_IWUSR);
module_param(channels,int, S_IRUGO|S_IWUSR);
MODULE_PARM_DESC(ifname," Net interface name, wlan%d=default");
//MODULE_PARM_DESC(hwseqnum," Try to use hardware 802.11 header sequence numbers. Zero=default");
MODULE_PARM_DESC(hwwep," Try to use hardware security support. ");
MODULE_PARM_DESC(channels," Channel bitmask for specific locales. NYI");
static int __devinit rtl8192_usb_probe(struct usb_interface *intf,
const struct usb_device_id *id);
static void __devexit rtl8192_usb_disconnect(struct usb_interface *intf);
static struct usb_driver rtl8192_usb_driver = {
.name = RTL819xU_MODULE_NAME, /* Driver name */
.id_table = rtl8192_usb_id_tbl, /* PCI_ID table */
.probe = rtl8192_usb_probe, /* probe fn */
.disconnect = rtl8192_usb_disconnect, /* remove fn */
#ifdef CONFIG_RTL8192_PM
.suspend = rtl8192_suspend, /* PM suspend fn */
.resume = rtl8192_resume, /* PM resume fn */
#else
.suspend = NULL, /* PM suspend fn */
.resume = NULL, /* PM resume fn */
#endif
};
typedef struct _CHANNEL_LIST
{
u8 Channel[32];
u8 Len;
}CHANNEL_LIST, *PCHANNEL_LIST;
static CHANNEL_LIST ChannelPlan[] = {
{{1,2,3,4,5,6,7,8,9,10,11,36,40,44,48,52,56,60,64,149,153,157,161,165},24}, //FCC
{{1,2,3,4,5,6,7,8,9,10,11},11}, //IC
{{1,2,3,4,5,6,7,8,9,10,11,12,13,36,40,44,48,52,56,60,64},21}, //ETSI
{{1,2,3,4,5,6,7,8,9,10,11,12,13},13}, //Spain. Change to ETSI.
{{1,2,3,4,5,6,7,8,9,10,11,12,13},13}, //France. Change to ETSI.
{{1,2,3,4,5,6,7,8,9,10,11,12,13,14,36,40,44,48,52,56,60,64},22}, //MKK //MKK
{{1,2,3,4,5,6,7,8,9,10,11,12,13,14,36,40,44,48,52,56,60,64},22},//MKK1
{{1,2,3,4,5,6,7,8,9,10,11,12,13},13}, //Israel.
{{1,2,3,4,5,6,7,8,9,10,11,12,13,14,36,40,44,48,52,56,60,64},22}, // For 11a , TELEC
{{1,2,3,4,5,6,7,8,9,10,11,12,13,14,36,40,44,48,52,56,60,64}, 22}, //MIC
{{1,2,3,4,5,6,7,8,9,10,11,12,13,14},14} //For Global Domain. 1-11:active scan, 12-14 passive scan. //+YJ, 080626
};
static void rtl819x_set_channel_map(u8 channel_plan, struct r8192_priv* priv)
{
int i, max_chan=-1, min_chan=-1;
struct ieee80211_device* ieee = priv->ieee80211;
switch (channel_plan)
{
case COUNTRY_CODE_FCC:
case COUNTRY_CODE_IC:
case COUNTRY_CODE_ETSI:
case COUNTRY_CODE_SPAIN:
case COUNTRY_CODE_FRANCE:
case COUNTRY_CODE_MKK:
case COUNTRY_CODE_MKK1:
case COUNTRY_CODE_ISRAEL:
case COUNTRY_CODE_TELEC:
case COUNTRY_CODE_MIC:
{
Dot11d_Init(ieee);
ieee->bGlobalDomain = false;
//acturally 8225 & 8256 rf chip only support B,G,24N mode
if ((priv->rf_chip == RF_8225) || (priv->rf_chip == RF_8256))
{
min_chan = 1;
max_chan = 14;
}
else
{
RT_TRACE(COMP_ERR, "unknown rf chip, can't set channel map in function:%s()\n", __FUNCTION__);
}
if (ChannelPlan[channel_plan].Len != 0){
// Clear old channel map
memset(GET_DOT11D_INFO(ieee)->channel_map, 0, sizeof(GET_DOT11D_INFO(ieee)->channel_map));
// Set new channel map
for (i=0;i<ChannelPlan[channel_plan].Len;i++)
{
if (ChannelPlan[channel_plan].Channel[i] < min_chan || ChannelPlan[channel_plan].Channel[i] > max_chan)
break;
GET_DOT11D_INFO(ieee)->channel_map[ChannelPlan[channel_plan].Channel[i]] = 1;
}
}
break;
}
case COUNTRY_CODE_GLOBAL_DOMAIN:
{
GET_DOT11D_INFO(ieee)->bEnabled = 0;//this flag enabled to follow 11d country IE setting, otherwise, it shall follow global domain settings.
Dot11d_Reset(ieee);
ieee->bGlobalDomain = true;
break;
}
default:
break;
}
return;
}
#define rx_hal_is_cck_rate(_pdrvinfo)\
(_pdrvinfo->RxRate == DESC90_RATE1M ||\
_pdrvinfo->RxRate == DESC90_RATE2M ||\
_pdrvinfo->RxRate == DESC90_RATE5_5M ||\
_pdrvinfo->RxRate == DESC90_RATE11M) &&\
!_pdrvinfo->RxHT\
void CamResetAllEntry(struct net_device *dev)
{
u32 ulcommand = 0;
//2004/02/11 In static WEP, OID_ADD_KEY or OID_ADD_WEP are set before STA associate to AP.
// However, ResetKey is called on OID_802_11_INFRASTRUCTURE_MODE and MlmeAssociateRequest
// In this condition, Cam can not be reset because upper layer will not set this static key again.
//if(Adapter->EncAlgorithm == WEP_Encryption)
// return;
//debug
//DbgPrint("========================================\n");
//DbgPrint(" Call ResetAllEntry \n");
//DbgPrint("========================================\n\n");
ulcommand |= BIT31|BIT30;
write_nic_dword(dev, RWCAM, ulcommand);
}
void write_cam(struct net_device *dev, u8 addr, u32 data)
{
write_nic_dword(dev, WCAMI, data);
write_nic_dword(dev, RWCAM, BIT31|BIT16|(addr&0xff) );
}
u32 read_cam(struct net_device *dev, u8 addr)
{
write_nic_dword(dev, RWCAM, 0x80000000|(addr&0xff) );
return read_nic_dword(dev, 0xa8);
}
void write_nic_byte_E(struct net_device *dev, int indx, u8 data)
{
int status;
struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
struct usb_device *udev = priv->udev;
status = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
RTL8187_REQ_SET_REGS, RTL8187_REQT_WRITE,
indx|0xfe00, 0, &data, 1, HZ / 2);
if (status < 0)
{
printk("write_nic_byte_E TimeOut! status:%d\n", status);
}
}
u8 read_nic_byte_E(struct net_device *dev, int indx)
{
int status;
u8 data;
struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
struct usb_device *udev = priv->udev;
status = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
RTL8187_REQ_GET_REGS, RTL8187_REQT_READ,
indx|0xfe00, 0, &data, 1, HZ / 2);
if (status < 0)
{
printk("read_nic_byte_E TimeOut! status:%d\n", status);
}
return data;
}
//as 92U has extend page from 4 to 16, so modify functions below.
void write_nic_byte(struct net_device *dev, int indx, u8 data)
{
int status;
struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
struct usb_device *udev = priv->udev;
status = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
RTL8187_REQ_SET_REGS, RTL8187_REQT_WRITE,
(indx&0xff)|0xff00, (indx>>8)&0x0f, &data, 1, HZ / 2);
if (status < 0)
{
printk("write_nic_byte TimeOut! status:%d\n", status);
}
}
void write_nic_word(struct net_device *dev, int indx, u16 data)
{
int status;
struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
struct usb_device *udev = priv->udev;
status = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
RTL8187_REQ_SET_REGS, RTL8187_REQT_WRITE,
(indx&0xff)|0xff00, (indx>>8)&0x0f, &data, 2, HZ / 2);
if (status < 0)
{
printk("write_nic_word TimeOut! status:%d\n", status);
}
}
void write_nic_dword(struct net_device *dev, int indx, u32 data)
{
int status;
struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
struct usb_device *udev = priv->udev;
status = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
RTL8187_REQ_SET_REGS, RTL8187_REQT_WRITE,
(indx&0xff)|0xff00, (indx>>8)&0x0f, &data, 4, HZ / 2);
if (status < 0)
{
printk("write_nic_dword TimeOut! status:%d\n", status);
}
}
u8 read_nic_byte(struct net_device *dev, int indx)
{
u8 data;
int status;
struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
struct usb_device *udev = priv->udev;
status = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
RTL8187_REQ_GET_REGS, RTL8187_REQT_READ,
(indx&0xff)|0xff00, (indx>>8)&0x0f, &data, 1, HZ / 2);
if (status < 0)
{
printk("read_nic_byte TimeOut! status:%d\n", status);
}
return data;
}
u16 read_nic_word(struct net_device *dev, int indx)
{
u16 data;
int status;
struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
struct usb_device *udev = priv->udev;
status = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
RTL8187_REQ_GET_REGS, RTL8187_REQT_READ,
(indx&0xff)|0xff00, (indx>>8)&0x0f,
&data, 2, HZ / 2);
if (status < 0)
printk("read_nic_word TimeOut! status:%d\n", status);
return data;
}
u16 read_nic_word_E(struct net_device *dev, int indx)
{
u16 data;
int status;
struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
struct usb_device *udev = priv->udev;
status = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
RTL8187_REQ_GET_REGS, RTL8187_REQT_READ,
indx|0xfe00, 0, &data, 2, HZ / 2);
if (status < 0)
printk("read_nic_word TimeOut! status:%d\n", status);
return data;
}
u32 read_nic_dword(struct net_device *dev, int indx)
{
u32 data;
int status;
/* int result; */
struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
struct usb_device *udev = priv->udev;
status = usb_control_msg(udev, usb_rcvctrlpipe(udev, 0),
RTL8187_REQ_GET_REGS, RTL8187_REQT_READ,
(indx&0xff)|0xff00, (indx>>8)&0x0f,
&data, 4, HZ / 2);
/* if(0 != result) {
* printk(KERN_WARNING "read size of data = %d\, date = %d\n",
* result, data);
* }
*/
if (status < 0)
printk("read_nic_dword TimeOut! status:%d\n", status);
return data;
}
/* u8 read_phy_cck(struct net_device *dev, u8 adr); */
/* u8 read_phy_ofdm(struct net_device *dev, u8 adr); */
/* this might still called in what was the PHY rtl8185/rtl8192 common code
* plans are to possibility turn it again in one common code...
*/
inline void force_pci_posting(struct net_device *dev)
{
}
static struct net_device_stats *rtl8192_stats(struct net_device *dev);
void rtl8192_commit(struct net_device *dev);
/* void rtl8192_restart(struct net_device *dev); */
void rtl8192_restart(struct work_struct *work);
/* void rtl8192_rq_tx_ack(struct work_struct *work); */
void watch_dog_timer_callback(unsigned long data);
/****************************************************************************
* -----------------------------PROCFS STUFF-------------------------
*****************************************************************************
*/
static struct proc_dir_entry *rtl8192_proc;
static int proc_get_stats_ap(char *page, char **start, off_t offset, int count,
int *eof, void *data)
{
struct net_device *dev = data;
struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
struct ieee80211_device *ieee = priv->ieee80211;
struct ieee80211_network *target;
int len = 0;
list_for_each_entry(target, &ieee->network_list, list) {
len += snprintf(page + len, count - len, "%s ", target->ssid);
if (target->wpa_ie_len > 0 || target->rsn_ie_len > 0)
len += snprintf(page + len, count - len, "WPA\n");
else
len += snprintf(page + len, count - len, "non_WPA\n");
}
*eof = 1;
return len;
}
static int proc_get_registers(char *page, char **start,
off_t offset, int count,
int *eof, void *data)
{
struct net_device *dev = data;
// struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
int len = 0;
int i,n;
int max=0xff;
/* This dump the current register page */
len += snprintf(page + len, count - len,
"\n####################page 0##################\n ");
for(n=0;n<=max;)
{
//printk( "\nD: %2x> ", n);
len += snprintf(page + len, count - len,
"\nD: %2x > ",n);
for(i=0;i<16 && n<=max;i++,n++)
len += snprintf(page + len, count - len,
"%2x ",read_nic_byte(dev,0x000|n));
// printk("%2x ",read_nic_byte(dev,n));
}
len += snprintf(page + len, count - len,
"\n####################page 1##################\n ");
for(n=0;n<=max;)
{
//printk( "\nD: %2x> ", n);
len += snprintf(page + len, count - len,
"\nD: %2x > ",n);
for(i=0;i<16 && n<=max;i++,n++)
len += snprintf(page + len, count - len,
"%2x ",read_nic_byte(dev,0x100|n));
// printk("%2x ",read_nic_byte(dev,n));
}
len += snprintf(page + len, count - len,
"\n####################page 3##################\n ");
for(n=0;n<=max;)
{
//printk( "\nD: %2x> ", n);
len += snprintf(page + len, count - len,
"\nD: %2x > ",n);
for(i=0;i<16 && n<=max;i++,n++)
len += snprintf(page + len, count - len,
"%2x ",read_nic_byte(dev,0x300|n));
// printk("%2x ",read_nic_byte(dev,n));
}
len += snprintf(page + len, count - len,"\n");
*eof = 1;
return len;
}
static int proc_get_stats_tx(char *page, char **start,
off_t offset, int count,
int *eof, void *data)
{
struct net_device *dev = data;
struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
int len = 0;
len += snprintf(page + len, count - len,
"TX VI priority ok int: %lu\n"
"TX VI priority error int: %lu\n"
"TX VO priority ok int: %lu\n"
"TX VO priority error int: %lu\n"
"TX BE priority ok int: %lu\n"
"TX BE priority error int: %lu\n"
"TX BK priority ok int: %lu\n"
"TX BK priority error int: %lu\n"
"TX MANAGE priority ok int: %lu\n"
"TX MANAGE priority error int: %lu\n"
"TX BEACON priority ok int: %lu\n"
"TX BEACON priority error int: %lu\n"
// "TX high priority ok int: %lu\n"
// "TX high priority failed error int: %lu\n"
"TX queue resume: %lu\n"
"TX queue stopped?: %d\n"
"TX fifo overflow: %lu\n"
// "TX beacon: %lu\n"
"TX VI queue: %d\n"
"TX VO queue: %d\n"
"TX BE queue: %d\n"
"TX BK queue: %d\n"
// "TX HW queue: %d\n"
"TX VI dropped: %lu\n"
"TX VO dropped: %lu\n"
"TX BE dropped: %lu\n"
"TX BK dropped: %lu\n"
"TX total data packets %lu\n",
// "TX beacon aborted: %lu\n",
priv->stats.txviokint,
priv->stats.txvierr,
priv->stats.txvookint,
priv->stats.txvoerr,
priv->stats.txbeokint,
priv->stats.txbeerr,
priv->stats.txbkokint,
priv->stats.txbkerr,
priv->stats.txmanageokint,
priv->stats.txmanageerr,
priv->stats.txbeaconokint,
priv->stats.txbeaconerr,
// priv->stats.txhpokint,
// priv->stats.txhperr,
priv->stats.txresumed,
netif_queue_stopped(dev),
priv->stats.txoverflow,
// priv->stats.txbeacon,
atomic_read(&(priv->tx_pending[VI_PRIORITY])),
atomic_read(&(priv->tx_pending[VO_PRIORITY])),
atomic_read(&(priv->tx_pending[BE_PRIORITY])),
atomic_read(&(priv->tx_pending[BK_PRIORITY])),
// read_nic_byte(dev, TXFIFOCOUNT),
priv->stats.txvidrop,
priv->stats.txvodrop,
priv->stats.txbedrop,
priv->stats.txbkdrop,
priv->stats.txdatapkt
// priv->stats.txbeaconerr
);
*eof = 1;
return len;
}
static int proc_get_stats_rx(char *page, char **start,
off_t offset, int count,
int *eof, void *data)
{
struct net_device *dev = data;
struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
int len = 0;
len += snprintf(page + len, count - len,
"RX packets: %lu\n"
"RX urb status error: %lu\n"
"RX invalid urb error: %lu\n",
priv->stats.rxoktotal,
priv->stats.rxstaterr,
priv->stats.rxurberr);
*eof = 1;
return len;
}
void rtl8192_proc_module_init(void)
{
RT_TRACE(COMP_INIT, "Initializing proc filesystem");
rtl8192_proc=create_proc_entry(RTL819xU_MODULE_NAME, S_IFDIR, init_net.proc_net);
}
void rtl8192_proc_module_remove(void)
{
remove_proc_entry(RTL819xU_MODULE_NAME, init_net.proc_net);
}
void rtl8192_proc_remove_one(struct net_device *dev)
{
struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
if (priv->dir_dev) {
// remove_proc_entry("stats-hw", priv->dir_dev);
remove_proc_entry("stats-tx", priv->dir_dev);
remove_proc_entry("stats-rx", priv->dir_dev);
// remove_proc_entry("stats-ieee", priv->dir_dev);
remove_proc_entry("stats-ap", priv->dir_dev);
remove_proc_entry("registers", priv->dir_dev);
// remove_proc_entry("cck-registers",priv->dir_dev);
// remove_proc_entry("ofdm-registers",priv->dir_dev);
//remove_proc_entry(dev->name, rtl8192_proc);
remove_proc_entry("wlan0", rtl8192_proc);
priv->dir_dev = NULL;
}
}
void rtl8192_proc_init_one(struct net_device *dev)
{
struct proc_dir_entry *e;
struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
priv->dir_dev = create_proc_entry(dev->name,
S_IFDIR | S_IRUGO | S_IXUGO,
rtl8192_proc);
if (!priv->dir_dev) {
RT_TRACE(COMP_ERR, "Unable to initialize /proc/net/rtl8192/%s\n",
dev->name);
return;
}
e = create_proc_read_entry("stats-rx", S_IFREG | S_IRUGO,
priv->dir_dev, proc_get_stats_rx, dev);
if (!e) {
RT_TRACE(COMP_ERR,"Unable to initialize "
"/proc/net/rtl8192/%s/stats-rx\n",
dev->name);
}
e = create_proc_read_entry("stats-tx", S_IFREG | S_IRUGO,
priv->dir_dev, proc_get_stats_tx, dev);
if (!e) {
RT_TRACE(COMP_ERR, "Unable to initialize "
"/proc/net/rtl8192/%s/stats-tx\n",
dev->name);
}
e = create_proc_read_entry("stats-ap", S_IFREG | S_IRUGO,
priv->dir_dev, proc_get_stats_ap, dev);
if (!e) {
RT_TRACE(COMP_ERR, "Unable to initialize "
"/proc/net/rtl8192/%s/stats-ap\n",
dev->name);
}
e = create_proc_read_entry("registers", S_IFREG | S_IRUGO,
priv->dir_dev, proc_get_registers, dev);
if (!e) {
RT_TRACE(COMP_ERR, "Unable to initialize "
"/proc/net/rtl8192/%s/registers\n",
dev->name);
}
}
/****************************************************************************
-----------------------------MISC STUFF-------------------------
*****************************************************************************/
/* this is only for debugging */
void print_buffer(u32 *buffer, int len)
{
int i;
u8 *buf =(u8*)buffer;
printk("ASCII BUFFER DUMP (len: %x):\n",len);
for(i=0;i<len;i++)
printk("%c",buf[i]);
printk("\nBINARY BUFFER DUMP (len: %x):\n",len);
for(i=0;i<len;i++)
printk("%x",buf[i]);
printk("\n");
}
//short check_nic_enough_desc(struct net_device *dev, priority_t priority)
short check_nic_enough_desc(struct net_device *dev,int queue_index)
{
struct r8192_priv *priv = ieee80211_priv(dev);
int used = atomic_read(&priv->tx_pending[queue_index]);
return (used < MAX_TX_URB);
}
void tx_timeout(struct net_device *dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
//rtl8192_commit(dev);
schedule_work(&priv->reset_wq);
//DMESG("TXTIMEOUT");
}
/* this is only for debug */
void dump_eprom(struct net_device *dev)
{
int i;
for(i=0; i<63; i++)
RT_TRACE(COMP_EPROM, "EEPROM addr %x : %x", i, eprom_read(dev,i));
}
/* this is only for debug */
void rtl8192_dump_reg(struct net_device *dev)
{
int i;
int n;
int max=0x1ff;
RT_TRACE(COMP_PHY, "Dumping NIC register map");
for(n=0;n<=max;)
{
printk( "\nD: %2x> ", n);
for(i=0;i<16 && n<=max;i++,n++)
printk("%2x ",read_nic_byte(dev,n));
}
printk("\n");
}
/****************************************************************************
------------------------------HW STUFF---------------------------
*****************************************************************************/
void rtl8192_set_mode(struct net_device *dev,int mode)
{
u8 ecmd;
ecmd=read_nic_byte(dev, EPROM_CMD);
ecmd=ecmd &~ EPROM_CMD_OPERATING_MODE_MASK;
ecmd=ecmd | (mode<<EPROM_CMD_OPERATING_MODE_SHIFT);
ecmd=ecmd &~ (1<<EPROM_CS_SHIFT);
ecmd=ecmd &~ (1<<EPROM_CK_SHIFT);
write_nic_byte(dev, EPROM_CMD, ecmd);
}
void rtl8192_update_msr(struct net_device *dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
u8 msr;
msr = read_nic_byte(dev, MSR);
msr &= ~ MSR_LINK_MASK;
/* do not change in link_state != WLAN_LINK_ASSOCIATED.
* msr must be updated if the state is ASSOCIATING.
* this is intentional and make sense for ad-hoc and
* master (see the create BSS/IBSS func)
*/
if (priv->ieee80211->state == IEEE80211_LINKED){
if (priv->ieee80211->iw_mode == IW_MODE_INFRA)
msr |= (MSR_LINK_MANAGED<<MSR_LINK_SHIFT);
else if (priv->ieee80211->iw_mode == IW_MODE_ADHOC)
msr |= (MSR_LINK_ADHOC<<MSR_LINK_SHIFT);
else if (priv->ieee80211->iw_mode == IW_MODE_MASTER)
msr |= (MSR_LINK_MASTER<<MSR_LINK_SHIFT);
}else
msr |= (MSR_LINK_NONE<<MSR_LINK_SHIFT);
write_nic_byte(dev, MSR, msr);
}
void rtl8192_set_chan(struct net_device *dev,short ch)
{
struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
// u32 tx;
RT_TRACE(COMP_CH, "=====>%s()====ch:%d\n", __FUNCTION__, ch);
priv->chan=ch;
/* this hack should avoid frame TX during channel setting*/
// tx = read_nic_dword(dev,TX_CONF);
// tx &= ~TX_LOOPBACK_MASK;
#ifndef LOOP_TEST
// write_nic_dword(dev,TX_CONF, tx |( TX_LOOPBACK_MAC<<TX_LOOPBACK_SHIFT));
//need to implement rf set channel here WB
if (priv->rf_set_chan)
priv->rf_set_chan(dev,priv->chan);
mdelay(10);
// write_nic_dword(dev,TX_CONF,tx | (TX_LOOPBACK_NONE<<TX_LOOPBACK_SHIFT));
#endif
}
static void rtl8192_rx_isr(struct urb *urb);
//static void rtl8192_rx_isr(struct urb *rx_urb);
u32 get_rxpacket_shiftbytes_819xusb(struct ieee80211_rx_stats *pstats)
{
#ifdef USB_RX_AGGREGATION_SUPPORT
if (pstats->bisrxaggrsubframe)
return (sizeof(rx_desc_819x_usb) + pstats->RxDrvInfoSize
+ pstats->RxBufShift + 8);
else
#endif
return (sizeof(rx_desc_819x_usb) + pstats->RxDrvInfoSize
+ pstats->RxBufShift);
}
static int rtl8192_rx_initiate(struct net_device*dev)
{
struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
struct urb *entry;
struct sk_buff *skb;
struct rtl8192_rx_info *info;
/* nomal packet rx procedure */
while (skb_queue_len(&priv->rx_queue) < MAX_RX_URB) {
skb = __dev_alloc_skb(RX_URB_SIZE, GFP_KERNEL);
if (!skb)
break;
entry = usb_alloc_urb(0, GFP_KERNEL);
if (!entry) {
kfree_skb(skb);
break;
}
// printk("nomal packet IN request!\n");
usb_fill_bulk_urb(entry, priv->udev,
usb_rcvbulkpipe(priv->udev, 3), skb_tail_pointer(skb),
RX_URB_SIZE, rtl8192_rx_isr, skb);
info = (struct rtl8192_rx_info *) skb->cb;
info->urb = entry;
info->dev = dev;
info->out_pipe = 3; //denote rx normal packet queue
skb_queue_tail(&priv->rx_queue, skb);
usb_submit_urb(entry, GFP_KERNEL);
}
/* command packet rx procedure */
while (skb_queue_len(&priv->rx_queue) < MAX_RX_URB + 3) {
// printk("command packet IN request!\n");
skb = __dev_alloc_skb(RX_URB_SIZE ,GFP_KERNEL);
if (!skb)
break;
entry = usb_alloc_urb(0, GFP_KERNEL);
if (!entry) {
kfree_skb(skb);
break;
}
usb_fill_bulk_urb(entry, priv->udev,
usb_rcvbulkpipe(priv->udev, 9), skb_tail_pointer(skb),
RX_URB_SIZE, rtl8192_rx_isr, skb);
info = (struct rtl8192_rx_info *) skb->cb;
info->urb = entry;
info->dev = dev;
info->out_pipe = 9; //denote rx cmd packet queue
skb_queue_tail(&priv->rx_queue, skb);
usb_submit_urb(entry, GFP_KERNEL);
}
return 0;
}
void rtl8192_set_rxconf(struct net_device *dev)
{
struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
u32 rxconf;
rxconf=read_nic_dword(dev,RCR);
rxconf = rxconf &~ MAC_FILTER_MASK;
rxconf = rxconf | RCR_AMF;
rxconf = rxconf | RCR_ADF;
rxconf = rxconf | RCR_AB;
rxconf = rxconf | RCR_AM;
//rxconf = rxconf | RCR_ACF;
if (dev->flags & IFF_PROMISC) {DMESG ("NIC in promisc mode");}
if(priv->ieee80211->iw_mode == IW_MODE_MONITOR || \
dev->flags & IFF_PROMISC){
rxconf = rxconf | RCR_AAP;
} /*else if(priv->ieee80211->iw_mode == IW_MODE_MASTER){
rxconf = rxconf | (1<<ACCEPT_ALLMAC_FRAME_SHIFT);
rxconf = rxconf | (1<<RX_CHECK_BSSID_SHIFT);
}*/else{
rxconf = rxconf | RCR_APM;
rxconf = rxconf | RCR_CBSSID;
}
if(priv->ieee80211->iw_mode == IW_MODE_MONITOR){
rxconf = rxconf | RCR_AICV;
rxconf = rxconf | RCR_APWRMGT;
}
if( priv->crcmon == 1 && priv->ieee80211->iw_mode == IW_MODE_MONITOR)
rxconf = rxconf | RCR_ACRC32;
rxconf = rxconf &~ RX_FIFO_THRESHOLD_MASK;
rxconf = rxconf | (RX_FIFO_THRESHOLD_NONE<<RX_FIFO_THRESHOLD_SHIFT);
rxconf = rxconf &~ MAX_RX_DMA_MASK;
rxconf = rxconf | ((u32)7<<RCR_MXDMA_OFFSET);
// rxconf = rxconf | (1<<RX_AUTORESETPHY_SHIFT);
rxconf = rxconf | RCR_ONLYERLPKT;
// rxconf = rxconf &~ RCR_CS_MASK;
// rxconf = rxconf | (1<<RCR_CS_SHIFT);
write_nic_dword(dev, RCR, rxconf);
#ifdef DEBUG_RX
DMESG("rxconf: %x %x",rxconf ,read_nic_dword(dev,RCR));
#endif
}
//wait to be removed
void rtl8192_rx_enable(struct net_device *dev)
{
//u8 cmd;
//struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
rtl8192_rx_initiate(dev);
// rtl8192_set_rxconf(dev);
}
void rtl8192_tx_enable(struct net_device *dev)
{
}
void rtl8192_rtx_disable(struct net_device *dev)
{
u8 cmd;
struct r8192_priv *priv = ieee80211_priv(dev);
struct sk_buff *skb;
struct rtl8192_rx_info *info;
cmd=read_nic_byte(dev,CMDR);
write_nic_byte(dev, CMDR, cmd &~ \
(CR_TE|CR_RE));
force_pci_posting(dev);
mdelay(10);
while ((skb = __skb_dequeue(&priv->rx_queue))) {
info = (struct rtl8192_rx_info *) skb->cb;
if (!info->urb)
continue;
usb_kill_urb(info->urb);
kfree_skb(skb);
}
if (skb_queue_len(&priv->skb_queue)) {
printk(KERN_WARNING "skb_queue not empty\n");
}
skb_queue_purge(&priv->skb_queue);
return;
}
int alloc_tx_beacon_desc_ring(struct net_device *dev, int count)
{
return 0;
}
inline u16 ieeerate2rtlrate(int rate)
{
switch(rate){
case 10:
return 0;
case 20:
return 1;
case 55:
return 2;
case 110:
return 3;
case 60:
return 4;
case 90:
return 5;
case 120:
return 6;
case 180:
return 7;
case 240:
return 8;
case 360:
return 9;
case 480:
return 10;
case 540:
return 11;
default:
return 3;
}
}
static u16 rtl_rate[] = {10,20,55,110,60,90,120,180,240,360,480,540};
inline u16 rtl8192_rate2rate(short rate)
{
if (rate >11) return 0;
return rtl_rate[rate];
}
/* The protype of rx_isr has changed since one verion of Linux Kernel */
static void rtl8192_rx_isr(struct urb *urb)
{
struct sk_buff *skb = (struct sk_buff *) urb->context;
struct rtl8192_rx_info *info = (struct rtl8192_rx_info *)skb->cb;
struct net_device *dev = info->dev;
struct r8192_priv *priv = ieee80211_priv(dev);
int out_pipe = info->out_pipe;
int err;
if(!priv->up)
return;
if (unlikely(urb->status)) {
info->urb = NULL;
priv->stats.rxstaterr++;
priv->ieee80211->stats.rx_errors++;
usb_free_urb(urb);
// printk("%s():rx status err\n",__FUNCTION__);
return;
}
skb_unlink(skb, &priv->rx_queue);
skb_put(skb, urb->actual_length);
skb_queue_tail(&priv->skb_queue, skb);
tasklet_schedule(&priv->irq_rx_tasklet);
skb = dev_alloc_skb(RX_URB_SIZE);
if (unlikely(!skb)) {
usb_free_urb(urb);
printk("%s():can,t alloc skb\n",__FUNCTION__);
/* TODO check rx queue length and refill *somewhere* */
return;
}
usb_fill_bulk_urb(urb, priv->udev,
usb_rcvbulkpipe(priv->udev, out_pipe), skb_tail_pointer(skb),
RX_URB_SIZE, rtl8192_rx_isr, skb);
info = (struct rtl8192_rx_info *) skb->cb;
info->urb = urb;
info->dev = dev;
info->out_pipe = out_pipe;
urb->transfer_buffer = skb_tail_pointer(skb);
urb->context = skb;
skb_queue_tail(&priv->rx_queue, skb);
err = usb_submit_urb(urb, GFP_ATOMIC);
if(err && err != EPERM)
printk("can not submit rxurb, err is %x,URB status is %x\n",err,urb->status);
}
u32
rtl819xusb_rx_command_packet(
struct net_device *dev,
struct ieee80211_rx_stats *pstats
)
{
u32 status;
//RT_TRACE(COMP_RECV, DBG_TRACE, ("---> RxCommandPacketHandle819xUsb()\n"));
status = cmpk_message_handle_rx(dev, pstats);
if (status)
{
DMESG("rxcommandpackethandle819xusb: It is a command packet\n");
}
else
{
//RT_TRACE(COMP_RECV, DBG_TRACE, ("RxCommandPacketHandle819xUsb: It is not a command packet\n"));
}
//RT_TRACE(COMP_RECV, DBG_TRACE, ("<--- RxCommandPacketHandle819xUsb()\n"));
return status;
}
void rtl8192_data_hard_stop(struct net_device *dev)
{
//FIXME !!
}
void rtl8192_data_hard_resume(struct net_device *dev)
{
// FIXME !!
}
/* this function TX data frames when the ieee80211 stack requires this.
* It checks also if we need to stop the ieee tx queue, eventually do it
*/
void rtl8192_hard_data_xmit(struct sk_buff *skb, struct net_device *dev, int rate)
{
struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
int ret;
unsigned long flags;
cb_desc *tcb_desc = (cb_desc *)(skb->cb + MAX_DEV_ADDR_SIZE);
u8 queue_index = tcb_desc->queue_index;
/* shall not be referred by command packet */
assert(queue_index != TXCMD_QUEUE);
spin_lock_irqsave(&priv->tx_lock,flags);
memcpy((unsigned char *)(skb->cb),&dev,sizeof(dev));
// tcb_desc->RATRIndex = 7;
// tcb_desc->bTxDisableRateFallBack = 1;
// tcb_desc->bTxUseDriverAssingedRate = 1;
tcb_desc->bTxEnableFwCalcDur = 1;
skb_push(skb, priv->ieee80211->tx_headroom);
ret = rtl8192_tx(dev, skb);
//priv->ieee80211->stats.tx_bytes+=(skb->len - priv->ieee80211->tx_headroom);
//priv->ieee80211->stats.tx_packets++;
spin_unlock_irqrestore(&priv->tx_lock,flags);
// return ret;
return;
}
/* This is a rough attempt to TX a frame
* This is called by the ieee 80211 stack to TX management frames.
* If the ring is full packet are dropped (for data frame the queue
* is stopped before this can happen).
*/
int rtl8192_hard_start_xmit(struct sk_buff *skb,struct net_device *dev)
{
struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
int ret;
unsigned long flags;
cb_desc *tcb_desc = (cb_desc *)(skb->cb + MAX_DEV_ADDR_SIZE);
u8 queue_index = tcb_desc->queue_index;
spin_lock_irqsave(&priv->tx_lock,flags);
memcpy((unsigned char *)(skb->cb),&dev,sizeof(dev));
if(queue_index == TXCMD_QUEUE) {
skb_push(skb, USB_HWDESC_HEADER_LEN);
rtl819xU_tx_cmd(dev, skb);
ret = 1;
spin_unlock_irqrestore(&priv->tx_lock,flags);
return ret;
} else {
skb_push(skb, priv->ieee80211->tx_headroom);
ret = rtl8192_tx(dev, skb);
}
spin_unlock_irqrestore(&priv->tx_lock,flags);
return ret;
}
void rtl8192_try_wake_queue(struct net_device *dev, int pri);
#ifdef USB_TX_DRIVER_AGGREGATION_ENABLE
u16 DrvAggr_PaddingAdd(struct net_device *dev, struct sk_buff *skb)
{
u16 PaddingNum = 256 - ((skb->len + TX_PACKET_DRVAGGR_SUBFRAME_SHIFT_BYTES) % 256);
return (PaddingNum&0xff);
}
u8 MRateToHwRate8190Pci(u8 rate);
u8 QueryIsShort(u8 TxHT, u8 TxRate, cb_desc *tcb_desc);
u8 MapHwQueueToFirmwareQueue(u8 QueueID);
struct sk_buff *DrvAggr_Aggregation(struct net_device *dev, struct ieee80211_drv_agg_txb *pSendList)
{
struct ieee80211_device *ieee = netdev_priv(dev);
struct r8192_priv *priv = ieee80211_priv(dev);
cb_desc *tcb_desc = NULL;
u8 i;
u32 TotalLength;
struct sk_buff *skb;
struct sk_buff *agg_skb;
tx_desc_819x_usb_aggr_subframe *tx_agg_desc = NULL;
tx_fwinfo_819x_usb *tx_fwinfo = NULL;
//
// Local variable initialization.
//
/* first skb initialization */
skb = pSendList->tx_agg_frames[0];
TotalLength = skb->len;
/* Get the total aggregation length including the padding space and
* sub frame header.
*/
for(i = 1; i < pSendList->nr_drv_agg_frames; i++) {
TotalLength += DrvAggr_PaddingAdd(dev, skb);
skb = pSendList->tx_agg_frames[i];
TotalLength += (skb->len + TX_PACKET_DRVAGGR_SUBFRAME_SHIFT_BYTES);
}
/* allocate skb to contain the aggregated packets */
agg_skb = dev_alloc_skb(TotalLength + ieee->tx_headroom);
memset(agg_skb->data, 0, agg_skb->len);
skb_reserve(agg_skb, ieee->tx_headroom);
// RT_DEBUG_DATA(COMP_SEND, skb->cb, sizeof(skb->cb));
/* reserve info for first subframe Tx descriptor to be set in the tx function */
skb = pSendList->tx_agg_frames[0];
tcb_desc = (cb_desc *)(skb->cb + MAX_DEV_ADDR_SIZE);
tcb_desc->drv_agg_enable = 1;
tcb_desc->pkt_size = skb->len;
tcb_desc->DrvAggrNum = pSendList->nr_drv_agg_frames;
printk("DrvAggNum = %d\n", tcb_desc->DrvAggrNum);
// RT_DEBUG_DATA(COMP_SEND, skb->cb, sizeof(skb->cb));
// printk("========>skb->data ======> \n");
// RT_DEBUG_DATA(COMP_SEND, skb->data, skb->len);
memcpy(agg_skb->cb, skb->cb, sizeof(skb->cb));
memcpy(skb_put(agg_skb,skb->len),skb->data,skb->len);
for(i = 1; i < pSendList->nr_drv_agg_frames; i++) {
/* push the next sub frame to be 256 byte aline */
skb_put(agg_skb,DrvAggr_PaddingAdd(dev,skb));
/* Subframe drv Tx descriptor and firmware info setting */
skb = pSendList->tx_agg_frames[i];
tcb_desc = (cb_desc *)(skb->cb + MAX_DEV_ADDR_SIZE);
tx_agg_desc = (tx_desc_819x_usb_aggr_subframe *)agg_skb->tail;
tx_fwinfo = (tx_fwinfo_819x_usb *)(agg_skb->tail + sizeof(tx_desc_819x_usb_aggr_subframe));
memset(tx_fwinfo,0,sizeof(tx_fwinfo_819x_usb));
/* DWORD 0 */
tx_fwinfo->TxHT = (tcb_desc->data_rate&0x80)?1:0;
tx_fwinfo->TxRate = MRateToHwRate8190Pci(tcb_desc->data_rate);
tx_fwinfo->EnableCPUDur = tcb_desc->bTxEnableFwCalcDur;
tx_fwinfo->Short = QueryIsShort(tx_fwinfo->TxHT, tx_fwinfo->TxRate, tcb_desc);
if(tcb_desc->bAMPDUEnable) {//AMPDU enabled
tx_fwinfo->AllowAggregation = 1;
/* DWORD 1 */
tx_fwinfo->RxMF = tcb_desc->ampdu_factor;
tx_fwinfo->RxAMD = tcb_desc->ampdu_density&0x07;//ampdudensity
} else {
tx_fwinfo->AllowAggregation = 0;
/* DWORD 1 */
tx_fwinfo->RxMF = 0;
tx_fwinfo->RxAMD = 0;
}
/* Protection mode related */
tx_fwinfo->RtsEnable = (tcb_desc->bRTSEnable)?1:0;
tx_fwinfo->CtsEnable = (tcb_desc->bCTSEnable)?1:0;
tx_fwinfo->RtsSTBC = (tcb_desc->bRTSSTBC)?1:0;
tx_fwinfo->RtsHT = (tcb_desc->rts_rate&0x80)?1:0;
tx_fwinfo->RtsRate = MRateToHwRate8190Pci((u8)tcb_desc->rts_rate);
tx_fwinfo->RtsSubcarrier = (tx_fwinfo->RtsHT==0)?(tcb_desc->RTSSC):0;
tx_fwinfo->RtsBandwidth = (tx_fwinfo->RtsHT==1)?((tcb_desc->bRTSBW)?1:0):0;
tx_fwinfo->RtsShort = (tx_fwinfo->RtsHT==0)?(tcb_desc->bRTSUseShortPreamble?1:0):\
(tcb_desc->bRTSUseShortGI?1:0);
/* Set Bandwidth and sub-channel settings. */
if(priv->CurrentChannelBW == HT_CHANNEL_WIDTH_20_40)
{
if(tcb_desc->bPacketBW) {
tx_fwinfo->TxBandwidth = 1;
tx_fwinfo->TxSubCarrier = 0; //By SD3's Jerry suggestion, use duplicated mode
} else {
tx_fwinfo->TxBandwidth = 0;
tx_fwinfo->TxSubCarrier = priv->nCur40MhzPrimeSC;
}
} else {
tx_fwinfo->TxBandwidth = 0;
tx_fwinfo->TxSubCarrier = 0;
}
/* Fill Tx descriptor */
memset(tx_agg_desc, 0, sizeof(tx_desc_819x_usb_aggr_subframe));
/* DWORD 0 */
//tx_agg_desc->LINIP = 0;
//tx_agg_desc->CmdInit = 1;
tx_agg_desc->Offset = sizeof(tx_fwinfo_819x_usb) + 8;
/* already raw data, need not to subtract header length */
tx_agg_desc->PktSize = skb->len & 0xffff;
/*DWORD 1*/
tx_agg_desc->SecCAMID= 0;
tx_agg_desc->RATid = tcb_desc->RATRIndex;
{
//MPDUOverhead = 0;
tx_agg_desc->NoEnc = 1;
}
tx_agg_desc->SecType = 0x0;
if (tcb_desc->bHwSec) {
switch (priv->ieee80211->pairwise_key_type)
{
case KEY_TYPE_WEP40:
case KEY_TYPE_WEP104:
tx_agg_desc->SecType = 0x1;
tx_agg_desc->NoEnc = 0;
break;
case KEY_TYPE_TKIP:
tx_agg_desc->SecType = 0x2;
tx_agg_desc->NoEnc = 0;
break;
case KEY_TYPE_CCMP:
tx_agg_desc->SecType = 0x3;
tx_agg_desc->NoEnc = 0;
break;
case KEY_TYPE_NA:
tx_agg_desc->SecType = 0x0;
tx_agg_desc->NoEnc = 1;
break;
}
}
tx_agg_desc->QueueSelect = MapHwQueueToFirmwareQueue(tcb_desc->queue_index);
tx_agg_desc->TxFWInfoSize = sizeof(tx_fwinfo_819x_usb);
tx_agg_desc->DISFB = tcb_desc->bTxDisableRateFallBack;
tx_agg_desc->USERATE = tcb_desc->bTxUseDriverAssingedRate;
tx_agg_desc->OWN = 1;
//DWORD 2
/* According windows driver, it seems that there no need to fill this field */
//tx_agg_desc->TxBufferSize= (u32)(skb->len - USB_HWDESC_HEADER_LEN);
/* to fill next packet */
skb_put(agg_skb,TX_PACKET_DRVAGGR_SUBFRAME_SHIFT_BYTES);
memcpy(skb_put(agg_skb,skb->len),skb->data,skb->len);
}
for(i = 0; i < pSendList->nr_drv_agg_frames; i++) {
dev_kfree_skb_any(pSendList->tx_agg_frames[i]);
}
return agg_skb;
}
/* NOTE:
This function return a list of PTCB which is proper to be aggregate with the input TCB.
If no proper TCB is found to do aggregation, SendList will only contain the input TCB.
*/
u8 DrvAggr_GetAggregatibleList(struct net_device *dev, struct sk_buff *skb,
struct ieee80211_drv_agg_txb *pSendList)
{
struct ieee80211_device *ieee = netdev_priv(dev);
PRT_HIGH_THROUGHPUT pHTInfo = ieee->pHTInfo;
u16 nMaxAggrNum = pHTInfo->UsbTxAggrNum;
cb_desc *tcb_desc = (cb_desc *)(skb->cb + MAX_DEV_ADDR_SIZE);
u8 QueueID = tcb_desc->queue_index;
do {
pSendList->tx_agg_frames[pSendList->nr_drv_agg_frames++] = skb;
if(pSendList->nr_drv_agg_frames >= nMaxAggrNum) {
break;
}
} while((skb = skb_dequeue(&ieee->skb_drv_aggQ[QueueID])));
RT_TRACE(COMP_AMSDU, "DrvAggr_GetAggregatibleList, nAggrTcbNum = %d \n", pSendList->nr_drv_agg_frames);
return pSendList->nr_drv_agg_frames;
}
#endif
static void rtl8192_tx_isr(struct urb *tx_urb)
{
struct sk_buff *skb = (struct sk_buff*)tx_urb->context;
struct net_device *dev = NULL;
struct r8192_priv *priv = NULL;
cb_desc *tcb_desc = (cb_desc *)(skb->cb + MAX_DEV_ADDR_SIZE);
u8 queue_index = tcb_desc->queue_index;
// bool bToSend0Byte;
// u16 BufLen = skb->len;
memcpy(&dev,(struct net_device*)(skb->cb),sizeof(struct net_device*));
priv = ieee80211_priv(dev);
if(tcb_desc->queue_index != TXCMD_QUEUE) {
if(tx_urb->status == 0) {
dev->trans_start = jiffies;
// As act as station mode, destion shall be unicast address.
//priv->ieee80211->stats.tx_bytes+=(skb->len - priv->ieee80211->tx_headroom);
//priv->ieee80211->stats.tx_packets++;
priv->stats.txoktotal++;
priv->ieee80211->LinkDetectInfo.NumTxOkInPeriod++;
priv->stats.txbytesunicast += (skb->len - priv->ieee80211->tx_headroom);
} else {
priv->ieee80211->stats.tx_errors++;
//priv->stats.txmanageerr++;
/* TODO */
}
}
/* free skb and tx_urb */
if(skb != NULL) {
dev_kfree_skb_any(skb);
usb_free_urb(tx_urb);
atomic_dec(&priv->tx_pending[queue_index]);
}
{
//
// Handle HW Beacon:
// We had transfer our beacon frame to host controller at this moment.
//
//
// Caution:
// Handling the wait queue of command packets.
// For Tx command packets, we must not do TCB fragment because it is not handled right now.
// We must cut the packets to match the size of TX_CMD_PKT before we send it.
//
/* Handle MPDU in wait queue. */
if(queue_index != BEACON_QUEUE) {
/* Don't send data frame during scanning.*/
if((skb_queue_len(&priv->ieee80211->skb_waitQ[queue_index]) != 0)&&\
(!(priv->ieee80211->queue_stop))) {
if(NULL != (skb = skb_dequeue(&(priv->ieee80211->skb_waitQ[queue_index]))))
priv->ieee80211->softmac_hard_start_xmit(skb, dev);
return; //modified by david to avoid further processing AMSDU
}
#ifdef USB_TX_DRIVER_AGGREGATION_ENABLE
else if ((skb_queue_len(&priv->ieee80211->skb_drv_aggQ[queue_index])!= 0)&&\
(!(priv->ieee80211->queue_stop))) {
// Tx Driver Aggregation process
/* The driver will aggregation the packets according to the following stets
* 1. check whether there's tx irq available, for it's a completion return
* function, it should contain enough tx irq;
* 2. check pakcet type;
* 3. initialize sendlist, check whether the to-be send packet no greater than 1
* 4. aggregation the packets, and fill firmware info and tx desc to it, etc.
* 5. check whehter the packet could be sent, otherwise just insert to wait head
* */
skb = skb_dequeue(&priv->ieee80211->skb_drv_aggQ[queue_index]);
if(!check_nic_enough_desc(dev, queue_index)) {
skb_queue_head(&(priv->ieee80211->skb_drv_aggQ[queue_index]), skb);
return;
}
{
/*TODO*/
/*
u8* pHeader = skb->data;
if(IsMgntQosData(pHeader) ||
IsMgntQData_Ack(pHeader) ||
IsMgntQData_Poll(pHeader) ||
IsMgntQData_Poll_Ack(pHeader)
)
*/
{
struct ieee80211_drv_agg_txb SendList;
memset(&SendList, 0, sizeof(struct ieee80211_drv_agg_txb));
if(DrvAggr_GetAggregatibleList(dev, skb, &SendList) > 1) {
skb = DrvAggr_Aggregation(dev, &SendList);
}
}
priv->ieee80211->softmac_hard_start_xmit(skb, dev);
}
}
#endif
}
}
}
void rtl8192_beacon_stop(struct net_device *dev)
{
u8 msr, msrm, msr2;
struct r8192_priv *priv = ieee80211_priv(dev);
msr = read_nic_byte(dev, MSR);
msrm = msr & MSR_LINK_MASK;
msr2 = msr & ~MSR_LINK_MASK;
if(NIC_8192U == priv->card_8192) {
usb_kill_urb(priv->rx_urb[MAX_RX_URB]);
}
if ((msrm == (MSR_LINK_ADHOC<<MSR_LINK_SHIFT) ||
(msrm == (MSR_LINK_MASTER<<MSR_LINK_SHIFT)))){
write_nic_byte(dev, MSR, msr2 | MSR_LINK_NONE);
write_nic_byte(dev, MSR, msr);
}
}
void rtl8192_config_rate(struct net_device* dev, u16* rate_config)
{
struct r8192_priv *priv = ieee80211_priv(dev);
struct ieee80211_network *net;
u8 i=0, basic_rate = 0;
net = & priv->ieee80211->current_network;
for (i=0; i<net->rates_len; i++)
{
basic_rate = net->rates[i]&0x7f;
switch(basic_rate)
{
case MGN_1M: *rate_config |= RRSR_1M; break;
case MGN_2M: *rate_config |= RRSR_2M; break;
case MGN_5_5M: *rate_config |= RRSR_5_5M; break;
case MGN_11M: *rate_config |= RRSR_11M; break;
case MGN_6M: *rate_config |= RRSR_6M; break;
case MGN_9M: *rate_config |= RRSR_9M; break;
case MGN_12M: *rate_config |= RRSR_12M; break;
case MGN_18M: *rate_config |= RRSR_18M; break;
case MGN_24M: *rate_config |= RRSR_24M; break;
case MGN_36M: *rate_config |= RRSR_36M; break;
case MGN_48M: *rate_config |= RRSR_48M; break;
case MGN_54M: *rate_config |= RRSR_54M; break;
}
}
for (i=0; i<net->rates_ex_len; i++)
{
basic_rate = net->rates_ex[i]&0x7f;
switch(basic_rate)
{
case MGN_1M: *rate_config |= RRSR_1M; break;
case MGN_2M: *rate_config |= RRSR_2M; break;
case MGN_5_5M: *rate_config |= RRSR_5_5M; break;
case MGN_11M: *rate_config |= RRSR_11M; break;
case MGN_6M: *rate_config |= RRSR_6M; break;
case MGN_9M: *rate_config |= RRSR_9M; break;
case MGN_12M: *rate_config |= RRSR_12M; break;
case MGN_18M: *rate_config |= RRSR_18M; break;
case MGN_24M: *rate_config |= RRSR_24M; break;
case MGN_36M: *rate_config |= RRSR_36M; break;
case MGN_48M: *rate_config |= RRSR_48M; break;
case MGN_54M: *rate_config |= RRSR_54M; break;
}
}
}
#define SHORT_SLOT_TIME 9
#define NON_SHORT_SLOT_TIME 20
void rtl8192_update_cap(struct net_device* dev, u16 cap)
{
u32 tmp = 0;
struct r8192_priv *priv = ieee80211_priv(dev);
struct ieee80211_network *net = &priv->ieee80211->current_network;
priv->short_preamble = cap & WLAN_CAPABILITY_SHORT_PREAMBLE;
tmp = priv->basic_rate;
if (priv->short_preamble)
tmp |= BRSR_AckShortPmb;
write_nic_dword(dev, RRSR, tmp);
if (net->mode & (IEEE_G|IEEE_N_24G))
{
u8 slot_time = 0;
if ((cap & WLAN_CAPABILITY_SHORT_SLOT)&&(!priv->ieee80211->pHTInfo->bCurrentRT2RTLongSlotTime))
{//short slot time
slot_time = SHORT_SLOT_TIME;
}
else //long slot time
slot_time = NON_SHORT_SLOT_TIME;
priv->slot_time = slot_time;
write_nic_byte(dev, SLOT_TIME, slot_time);
}
}
void rtl8192_net_update(struct net_device *dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
struct ieee80211_network *net;
u16 BcnTimeCfg = 0, BcnCW = 6, BcnIFS = 0xf;
u16 rate_config = 0;
net = & priv->ieee80211->current_network;
rtl8192_config_rate(dev, &rate_config);
priv->basic_rate = rate_config &= 0x15f;
write_nic_dword(dev,BSSIDR,((u32*)net->bssid)[0]);
write_nic_word(dev,BSSIDR+4,((u16*)net->bssid)[2]);
//for(i=0;i<ETH_ALEN;i++)
// write_nic_byte(dev,BSSID+i,net->bssid[i]);
rtl8192_update_msr(dev);
// rtl8192_update_cap(dev, net->capability);
if (priv->ieee80211->iw_mode == IW_MODE_ADHOC)
{
write_nic_word(dev, ATIMWND, 2);
write_nic_word(dev, BCN_DMATIME, 1023);
write_nic_word(dev, BCN_INTERVAL, net->beacon_interval);
// write_nic_word(dev, BcnIntTime, 100);
write_nic_word(dev, BCN_DRV_EARLY_INT, 1);
write_nic_byte(dev, BCN_ERR_THRESH, 100);
BcnTimeCfg |= (BcnCW<<BCN_TCFG_CW_SHIFT);
// TODO: BcnIFS may required to be changed on ASIC
BcnTimeCfg |= BcnIFS<<BCN_TCFG_IFS;
write_nic_word(dev, BCN_TCFG, BcnTimeCfg);
}
}
//temporary hw beacon is not used any more.
//open it when necessary
void rtl819xusb_beacon_tx(struct net_device *dev,u16 tx_rate)
{
}
inline u8 rtl8192_IsWirelessBMode(u16 rate)
{
if( ((rate <= 110) && (rate != 60) && (rate != 90)) || (rate == 220) )
return 1;
else return 0;
}
u16 N_DBPSOfRate(u16 DataRate);
u16 ComputeTxTime(
u16 FrameLength,
u16 DataRate,
u8 bManagementFrame,
u8 bShortPreamble
)
{
u16 FrameTime;
u16 N_DBPS;
u16 Ceiling;
if( rtl8192_IsWirelessBMode(DataRate) )
{
if( bManagementFrame || !bShortPreamble || DataRate == 10 )
{ // long preamble
FrameTime = (u16)(144+48+(FrameLength*8/(DataRate/10)));
}
else
{ // Short preamble
FrameTime = (u16)(72+24+(FrameLength*8/(DataRate/10)));
}
if( ( FrameLength*8 % (DataRate/10) ) != 0 ) //Get the Ceilling
FrameTime ++;
} else { //802.11g DSSS-OFDM PLCP length field calculation.
N_DBPS = N_DBPSOfRate(DataRate);
Ceiling = (16 + 8*FrameLength + 6) / N_DBPS
+ (((16 + 8*FrameLength + 6) % N_DBPS) ? 1 : 0);
FrameTime = (u16)(16 + 4 + 4*Ceiling + 6);
}
return FrameTime;
}
u16 N_DBPSOfRate(u16 DataRate)
{
u16 N_DBPS = 24;
switch(DataRate)
{
case 60:
N_DBPS = 24;
break;
case 90:
N_DBPS = 36;
break;
case 120:
N_DBPS = 48;
break;
case 180:
N_DBPS = 72;
break;
case 240:
N_DBPS = 96;
break;
case 360:
N_DBPS = 144;
break;
case 480:
N_DBPS = 192;
break;
case 540:
N_DBPS = 216;
break;
default:
break;
}
return N_DBPS;
}
void rtl819xU_cmd_isr(struct urb *tx_cmd_urb, struct pt_regs *regs)
{
usb_free_urb(tx_cmd_urb);
}
unsigned int txqueue2outpipe(struct r8192_priv* priv,unsigned int tx_queue) {
if(tx_queue >= 9)
{
RT_TRACE(COMP_ERR,"%s():Unknown queue ID!!!\n",__FUNCTION__);
return 0x04;
}
return priv->txqueue_to_outpipemap[tx_queue];
}
short rtl819xU_tx_cmd(struct net_device *dev, struct sk_buff *skb)
{
struct r8192_priv *priv = ieee80211_priv(dev);
//u8 *tx;
int status;
struct urb *tx_urb;
//int urb_buf_len;
unsigned int idx_pipe;
tx_desc_cmd_819x_usb *pdesc = (tx_desc_cmd_819x_usb *)skb->data;
cb_desc *tcb_desc = (cb_desc *)(skb->cb + MAX_DEV_ADDR_SIZE);
u8 queue_index = tcb_desc->queue_index;
//printk("\n %s::queue_index = %d\n",__FUNCTION__, queue_index);
atomic_inc(&priv->tx_pending[queue_index]);
tx_urb = usb_alloc_urb(0,GFP_ATOMIC);
if(!tx_urb){
dev_kfree_skb(skb);
return -ENOMEM;
}
memset(pdesc, 0, USB_HWDESC_HEADER_LEN);
/* Tx descriptor ought to be set according to the skb->cb */
pdesc->FirstSeg = 1;//bFirstSeg;
pdesc->LastSeg = 1;//bLastSeg;
pdesc->CmdInit = tcb_desc->bCmdOrInit;
pdesc->TxBufferSize = tcb_desc->txbuf_size;
pdesc->OWN = 1;
pdesc->LINIP = tcb_desc->bLastIniPkt;
//----------------------------------------------------------------------------
// Fill up USB_OUT_CONTEXT.
//----------------------------------------------------------------------------
// Get index to out pipe from specified QueueID.
#ifndef USE_ONE_PIPE
idx_pipe = txqueue2outpipe(priv,queue_index);
#else
idx_pipe = 0x04;
#endif
#ifdef JOHN_DUMP_TXDESC
int i;
printk("<Tx descriptor>--rate %x---",rate);
for (i = 0; i < 8; i++)
printk("%8x ", tx[i]);
printk("\n");
#endif
usb_fill_bulk_urb(tx_urb,priv->udev, usb_sndbulkpipe(priv->udev,idx_pipe), \
skb->data, skb->len, rtl8192_tx_isr, skb);
status = usb_submit_urb(tx_urb, GFP_ATOMIC);
if (!status){
return 0;
}else{
DMESGE("Error TX CMD URB, error %d",
status);
return -1;
}
}
/*
* Mapping Software/Hardware descriptor queue id to "Queue Select Field"
* in TxFwInfo data structure
* 2006.10.30 by Emily
*
* \param QUEUEID Software Queue
*/
u8 MapHwQueueToFirmwareQueue(u8 QueueID)
{
u8 QueueSelect = 0x0; //defualt set to
switch(QueueID) {
case BE_QUEUE:
QueueSelect = QSLT_BE; //or QSelect = pTcb->priority;
break;
case BK_QUEUE:
QueueSelect = QSLT_BK; //or QSelect = pTcb->priority;
break;
case VO_QUEUE:
QueueSelect = QSLT_VO; //or QSelect = pTcb->priority;
break;
case VI_QUEUE:
QueueSelect = QSLT_VI; //or QSelect = pTcb->priority;
break;
case MGNT_QUEUE:
QueueSelect = QSLT_MGNT;
break;
case BEACON_QUEUE:
QueueSelect = QSLT_BEACON;
break;
// TODO: 2006.10.30 mark other queue selection until we verify it is OK
// TODO: Remove Assertions
//#if (RTL819X_FPGA_VER & RTL819X_FPGA_GUANGAN_070502)
case TXCMD_QUEUE:
QueueSelect = QSLT_CMD;
break;
//#endif
case HIGH_QUEUE:
QueueSelect = QSLT_HIGH;
break;
default:
RT_TRACE(COMP_ERR, "TransmitTCB(): Impossible Queue Selection: %d \n", QueueID);
break;
}
return QueueSelect;
}
u8 MRateToHwRate8190Pci(u8 rate)
{
u8 ret = DESC90_RATE1M;
switch(rate) {
case MGN_1M: ret = DESC90_RATE1M; break;
case MGN_2M: ret = DESC90_RATE2M; break;
case MGN_5_5M: ret = DESC90_RATE5_5M; break;
case MGN_11M: ret = DESC90_RATE11M; break;
case MGN_6M: ret = DESC90_RATE6M; break;
case MGN_9M: ret = DESC90_RATE9M; break;
case MGN_12M: ret = DESC90_RATE12M; break;
case MGN_18M: ret = DESC90_RATE18M; break;
case MGN_24M: ret = DESC90_RATE24M; break;
case MGN_36M: ret = DESC90_RATE36M; break;
case MGN_48M: ret = DESC90_RATE48M; break;
case MGN_54M: ret = DESC90_RATE54M; break;
// HT rate since here
case MGN_MCS0: ret = DESC90_RATEMCS0; break;
case MGN_MCS1: ret = DESC90_RATEMCS1; break;
case MGN_MCS2: ret = DESC90_RATEMCS2; break;
case MGN_MCS3: ret = DESC90_RATEMCS3; break;
case MGN_MCS4: ret = DESC90_RATEMCS4; break;
case MGN_MCS5: ret = DESC90_RATEMCS5; break;
case MGN_MCS6: ret = DESC90_RATEMCS6; break;
case MGN_MCS7: ret = DESC90_RATEMCS7; break;
case MGN_MCS8: ret = DESC90_RATEMCS8; break;
case MGN_MCS9: ret = DESC90_RATEMCS9; break;
case MGN_MCS10: ret = DESC90_RATEMCS10; break;
case MGN_MCS11: ret = DESC90_RATEMCS11; break;
case MGN_MCS12: ret = DESC90_RATEMCS12; break;
case MGN_MCS13: ret = DESC90_RATEMCS13; break;
case MGN_MCS14: ret = DESC90_RATEMCS14; break;
case MGN_MCS15: ret = DESC90_RATEMCS15; break;
case (0x80|0x20): ret = DESC90_RATEMCS32; break;
default: break;
}
return ret;
}
u8 QueryIsShort(u8 TxHT, u8 TxRate, cb_desc *tcb_desc)
{
u8 tmp_Short;
tmp_Short = (TxHT==1)?((tcb_desc->bUseShortGI)?1:0):((tcb_desc->bUseShortPreamble)?1:0);
if(TxHT==1 && TxRate != DESC90_RATEMCS15)
tmp_Short = 0;
return tmp_Short;
}
static void tx_zero_isr(struct urb *tx_urb)
{
return;
}
/*
* The tx procedure is just as following,
* skb->cb will contain all the following information,
* priority, morefrag, rate, &dev.
* */
short rtl8192_tx(struct net_device *dev, struct sk_buff* skb)
{
struct r8192_priv *priv = ieee80211_priv(dev);
cb_desc *tcb_desc = (cb_desc *)(skb->cb + MAX_DEV_ADDR_SIZE);
tx_desc_819x_usb *tx_desc = (tx_desc_819x_usb *)skb->data;
tx_fwinfo_819x_usb *tx_fwinfo = (tx_fwinfo_819x_usb *)(skb->data + USB_HWDESC_HEADER_LEN);
struct usb_device *udev = priv->udev;
int pend;
int status;
struct urb *tx_urb = NULL, *tx_urb_zero = NULL;
//int urb_len;
unsigned int idx_pipe;
// RT_DEBUG_DATA(COMP_SEND, tcb_desc, sizeof(cb_desc));
// printk("=============> %s\n", __FUNCTION__);
pend = atomic_read(&priv->tx_pending[tcb_desc->queue_index]);
/* we are locked here so the two atomic_read and inc are executed
* without interleaves
* !!! For debug purpose
*/
if( pend > MAX_TX_URB){
printk("To discard skb packet!\n");
dev_kfree_skb_any(skb);
return -1;
}
tx_urb = usb_alloc_urb(0,GFP_ATOMIC);
if(!tx_urb){
dev_kfree_skb_any(skb);
return -ENOMEM;
}
/* Fill Tx firmware info */
memset(tx_fwinfo,0,sizeof(tx_fwinfo_819x_usb));
/* DWORD 0 */
tx_fwinfo->TxHT = (tcb_desc->data_rate&0x80)?1:0;
tx_fwinfo->TxRate = MRateToHwRate8190Pci(tcb_desc->data_rate);
tx_fwinfo->EnableCPUDur = tcb_desc->bTxEnableFwCalcDur;
tx_fwinfo->Short = QueryIsShort(tx_fwinfo->TxHT, tx_fwinfo->TxRate, tcb_desc);
if(tcb_desc->bAMPDUEnable) {//AMPDU enabled
tx_fwinfo->AllowAggregation = 1;
/* DWORD 1 */
tx_fwinfo->RxMF = tcb_desc->ampdu_factor;
tx_fwinfo->RxAMD = tcb_desc->ampdu_density&0x07;//ampdudensity
} else {
tx_fwinfo->AllowAggregation = 0;
/* DWORD 1 */
tx_fwinfo->RxMF = 0;
tx_fwinfo->RxAMD = 0;
}
/* Protection mode related */
tx_fwinfo->RtsEnable = (tcb_desc->bRTSEnable)?1:0;
tx_fwinfo->CtsEnable = (tcb_desc->bCTSEnable)?1:0;
tx_fwinfo->RtsSTBC = (tcb_desc->bRTSSTBC)?1:0;
tx_fwinfo->RtsHT = (tcb_desc->rts_rate&0x80)?1:0;
tx_fwinfo->RtsRate = MRateToHwRate8190Pci((u8)tcb_desc->rts_rate);
tx_fwinfo->RtsSubcarrier = (tx_fwinfo->RtsHT==0)?(tcb_desc->RTSSC):0;
tx_fwinfo->RtsBandwidth = (tx_fwinfo->RtsHT==1)?((tcb_desc->bRTSBW)?1:0):0;
tx_fwinfo->RtsShort = (tx_fwinfo->RtsHT==0)?(tcb_desc->bRTSUseShortPreamble?1:0):\
(tcb_desc->bRTSUseShortGI?1:0);
/* Set Bandwidth and sub-channel settings. */
if(priv->CurrentChannelBW == HT_CHANNEL_WIDTH_20_40)
{
if(tcb_desc->bPacketBW) {
tx_fwinfo->TxBandwidth = 1;
tx_fwinfo->TxSubCarrier = 0; //By SD3's Jerry suggestion, use duplicated mode
} else {
tx_fwinfo->TxBandwidth = 0;
tx_fwinfo->TxSubCarrier = priv->nCur40MhzPrimeSC;
}
} else {
tx_fwinfo->TxBandwidth = 0;
tx_fwinfo->TxSubCarrier = 0;
}
#ifdef USB_TX_DRIVER_AGGREGATION_ENABLE
if (tcb_desc->drv_agg_enable)
{
tx_fwinfo->Tx_INFO_RSVD = (tcb_desc->DrvAggrNum & 0x1f) << 1;
}
#endif
/* Fill Tx descriptor */
memset(tx_desc, 0, sizeof(tx_desc_819x_usb));
/* DWORD 0 */
tx_desc->LINIP = 0;
tx_desc->CmdInit = 1;
tx_desc->Offset = sizeof(tx_fwinfo_819x_usb) + 8;
#ifdef USB_TX_DRIVER_AGGREGATION_ENABLE
if (tcb_desc->drv_agg_enable) {
tx_desc->PktSize = tcb_desc->pkt_size;
} else
#endif
{
tx_desc->PktSize = (skb->len - TX_PACKET_SHIFT_BYTES) & 0xffff;
}
/*DWORD 1*/
tx_desc->SecCAMID= 0;
tx_desc->RATid = tcb_desc->RATRIndex;
{
//MPDUOverhead = 0;
tx_desc->NoEnc = 1;
}
tx_desc->SecType = 0x0;
if (tcb_desc->bHwSec)
{
switch (priv->ieee80211->pairwise_key_type)
{
case KEY_TYPE_WEP40:
case KEY_TYPE_WEP104:
tx_desc->SecType = 0x1;
tx_desc->NoEnc = 0;
break;
case KEY_TYPE_TKIP:
tx_desc->SecType = 0x2;
tx_desc->NoEnc = 0;
break;
case KEY_TYPE_CCMP:
tx_desc->SecType = 0x3;
tx_desc->NoEnc = 0;
break;
case KEY_TYPE_NA:
tx_desc->SecType = 0x0;
tx_desc->NoEnc = 1;
break;
}
}
tx_desc->QueueSelect = MapHwQueueToFirmwareQueue(tcb_desc->queue_index);
tx_desc->TxFWInfoSize = sizeof(tx_fwinfo_819x_usb);
tx_desc->DISFB = tcb_desc->bTxDisableRateFallBack;
tx_desc->USERATE = tcb_desc->bTxUseDriverAssingedRate;
/* Fill fields that are required to be initialized in all of the descriptors */
//DWORD 0
tx_desc->FirstSeg = 1;
tx_desc->LastSeg = 1;
tx_desc->OWN = 1;
#ifdef USB_TX_DRIVER_AGGREGATION_ENABLE
if (tcb_desc->drv_agg_enable) {
tx_desc->TxBufferSize = tcb_desc->pkt_size + sizeof(tx_fwinfo_819x_usb);
} else
#endif
{
//DWORD 2
tx_desc->TxBufferSize = (u32)(skb->len - USB_HWDESC_HEADER_LEN);
}
/* Get index to out pipe from specified QueueID */
#ifndef USE_ONE_PIPE
idx_pipe = txqueue2outpipe(priv,tcb_desc->queue_index);
#else
idx_pipe = 0x5;
#endif
//RT_DEBUG_DATA(COMP_SEND,tx_fwinfo,sizeof(tx_fwinfo_819x_usb));
//RT_DEBUG_DATA(COMP_SEND,tx_desc,sizeof(tx_desc_819x_usb));
/* To submit bulk urb */
usb_fill_bulk_urb(tx_urb,udev,
usb_sndbulkpipe(udev,idx_pipe), skb->data,
skb->len, rtl8192_tx_isr, skb);
status = usb_submit_urb(tx_urb, GFP_ATOMIC);
if (!status){
//we need to send 0 byte packet whenever 512N bytes/64N(HIGN SPEED/NORMAL SPEED) bytes packet has been transmitted. Otherwise, it will be halt to wait for another packet. WB. 2008.08.27
bool bSend0Byte = false;
u8 zero = 0;
if(udev->speed == USB_SPEED_HIGH)
{
if (skb->len > 0 && skb->len % 512 == 0)
bSend0Byte = true;
}
else
{
if (skb->len > 0 && skb->len % 64 == 0)
bSend0Byte = true;
}
if (bSend0Byte)
{
tx_urb_zero = usb_alloc_urb(0,GFP_ATOMIC);
if(!tx_urb_zero){
RT_TRACE(COMP_ERR, "can't alloc urb for zero byte\n");
return -ENOMEM;
}
usb_fill_bulk_urb(tx_urb_zero,udev,
usb_sndbulkpipe(udev,idx_pipe), &zero,
0, tx_zero_isr, dev);
status = usb_submit_urb(tx_urb_zero, GFP_ATOMIC);
if (status){
RT_TRACE(COMP_ERR, "Error TX URB for zero byte %d, error %d", atomic_read(&priv->tx_pending[tcb_desc->queue_index]), status);
return -1;
}
}
dev->trans_start = jiffies;
atomic_inc(&priv->tx_pending[tcb_desc->queue_index]);
return 0;
}else{
RT_TRACE(COMP_ERR, "Error TX URB %d, error %d", atomic_read(&priv->tx_pending[tcb_desc->queue_index]),
status);
return -1;
}
}
short rtl8192_usb_initendpoints(struct net_device *dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
priv->rx_urb = kmalloc(sizeof(struct urb *) * (MAX_RX_URB+1),
GFP_KERNEL);
if (priv->rx_urb == NULL)
return -ENOMEM;
#ifndef JACKSON_NEW_RX
for(i=0;i<(MAX_RX_URB+1);i++){
priv->rx_urb[i] = usb_alloc_urb(0,GFP_KERNEL);
priv->rx_urb[i]->transfer_buffer = kmalloc(RX_URB_SIZE, GFP_KERNEL);
priv->rx_urb[i]->transfer_buffer_length = RX_URB_SIZE;
}
#endif
#ifdef THOMAS_BEACON
{
long align = 0;
void *oldaddr, *newaddr;
priv->rx_urb[16] = usb_alloc_urb(0, GFP_KERNEL);
priv->oldaddr = kmalloc(16, GFP_KERNEL);
oldaddr = priv->oldaddr;
align = ((long)oldaddr) & 3;
if (align) {
newaddr = oldaddr + 4 - align;
priv->rx_urb[16]->transfer_buffer_length = 16 - 4 + align;
} else {
newaddr = oldaddr;
priv->rx_urb[16]->transfer_buffer_length = 16;
}
priv->rx_urb[16]->transfer_buffer = newaddr;
}
#endif
memset(priv->rx_urb, 0, sizeof(struct urb*) * MAX_RX_URB);
priv->pp_rxskb = kcalloc(MAX_RX_URB, sizeof(struct sk_buff *),
GFP_KERNEL);
if (priv->pp_rxskb == NULL)
goto destroy;
goto _middle;
destroy:
kfree(priv->pp_rxskb);
kfree(priv->rx_urb);
priv->pp_rxskb = NULL;
priv->rx_urb = NULL;
DMESGE("Endpoint Alloc Failure");
return -ENOMEM;
_middle:
printk("End of initendpoints\n");
return 0;
}
#ifdef THOMAS_BEACON
void rtl8192_usb_deleteendpoints(struct net_device *dev)
{
int i;
struct r8192_priv *priv = ieee80211_priv(dev);
if(priv->rx_urb){
for(i=0;i<(MAX_RX_URB+1);i++){
usb_kill_urb(priv->rx_urb[i]);
usb_free_urb(priv->rx_urb[i]);
}
kfree(priv->rx_urb);
priv->rx_urb = NULL;
}
kfree(priv->oldaddr);
priv->oldaddr = NULL;
if (priv->pp_rxskb) {
kfree(priv->pp_rxskb);
priv->pp_rxskb = 0;
}
}
#else
void rtl8192_usb_deleteendpoints(struct net_device *dev)
{
int i;
struct r8192_priv *priv = ieee80211_priv(dev);
#ifndef JACKSON_NEW_RX
if(priv->rx_urb){
for(i=0;i<(MAX_RX_URB+1);i++){
usb_kill_urb(priv->rx_urb[i]);
kfree(priv->rx_urb[i]->transfer_buffer);
usb_free_urb(priv->rx_urb[i]);
}
kfree(priv->rx_urb);
priv->rx_urb = NULL;
}
#else
kfree(priv->rx_urb);
priv->rx_urb = NULL;
kfree(priv->oldaddr);
priv->oldaddr = NULL;
if (priv->pp_rxskb) {
kfree(priv->pp_rxskb);
priv->pp_rxskb = 0;
}
#endif
}
#endif
extern void rtl8192_update_ratr_table(struct net_device* dev);
void rtl8192_link_change(struct net_device *dev)
{
// int i;
struct r8192_priv *priv = ieee80211_priv(dev);
struct ieee80211_device* ieee = priv->ieee80211;
//write_nic_word(dev, BCN_INTR_ITV, net->beacon_interval);
if (ieee->state == IEEE80211_LINKED)
{
rtl8192_net_update(dev);
rtl8192_update_ratr_table(dev);
//add this as in pure N mode, wep encryption will use software way, but there is no chance to set this as wep will not set group key in wext. WB.2008.07.08
if ((KEY_TYPE_WEP40 == ieee->pairwise_key_type) || (KEY_TYPE_WEP104 == ieee->pairwise_key_type))
EnableHWSecurityConfig8192(dev);
}
/*update timing params*/
// RT_TRACE(COMP_CH, "========>%s(), chan:%d\n", __FUNCTION__, priv->chan);
// rtl8192_set_chan(dev, priv->chan);
if (ieee->iw_mode == IW_MODE_INFRA || ieee->iw_mode == IW_MODE_ADHOC)
{
u32 reg = 0;
reg = read_nic_dword(dev, RCR);
if (priv->ieee80211->state == IEEE80211_LINKED)
priv->ReceiveConfig = reg |= RCR_CBSSID;
else
priv->ReceiveConfig = reg &= ~RCR_CBSSID;
write_nic_dword(dev, RCR, reg);
}
// rtl8192_set_rxconf(dev);
}
static struct ieee80211_qos_parameters def_qos_parameters = {
{3,3,3,3},/* cw_min */
{7,7,7,7},/* cw_max */
{2,2,2,2},/* aifs */
{0,0,0,0},/* flags */
{0,0,0,0} /* tx_op_limit */
};
void rtl8192_update_beacon(struct work_struct * work)
{
struct r8192_priv *priv = container_of(work, struct r8192_priv, update_beacon_wq.work);
struct net_device *dev = priv->ieee80211->dev;
struct ieee80211_device* ieee = priv->ieee80211;
struct ieee80211_network* net = &ieee->current_network;
if (ieee->pHTInfo->bCurrentHTSupport)
HTUpdateSelfAndPeerSetting(ieee, net);
ieee->pHTInfo->bCurrentRT2RTLongSlotTime = net->bssht.bdRT2RTLongSlotTime;
rtl8192_update_cap(dev, net->capability);
}
/*
* background support to run QoS activate functionality
*/
int WDCAPARA_ADD[] = {EDCAPARA_BE,EDCAPARA_BK,EDCAPARA_VI,EDCAPARA_VO};
void rtl8192_qos_activate(struct work_struct * work)
{
struct r8192_priv *priv = container_of(work, struct r8192_priv, qos_activate);
struct net_device *dev = priv->ieee80211->dev;
struct ieee80211_qos_parameters *qos_parameters = &priv->ieee80211->current_network.qos_data.parameters;
u8 mode = priv->ieee80211->current_network.mode;
//u32 size = sizeof(struct ieee80211_qos_parameters);
u8 u1bAIFS;
u32 u4bAcParam;
int i;
if (priv == NULL)
return;
mutex_lock(&priv->mutex);
if(priv->ieee80211->state != IEEE80211_LINKED)
goto success;
RT_TRACE(COMP_QOS,"qos active process with associate response received\n");
/* It better set slot time at first */
/* For we just support b/g mode at present, let the slot time at 9/20 selection */
/* update the ac parameter to related registers */
for(i = 0; i < QOS_QUEUE_NUM; i++) {
//Mode G/A: slotTimeTimer = 9; Mode B: 20
u1bAIFS = qos_parameters->aifs[i] * ((mode&(IEEE_G|IEEE_N_24G)) ?9:20) + aSifsTime;
u4bAcParam = ((((u32)(qos_parameters->tx_op_limit[i]))<< AC_PARAM_TXOP_LIMIT_OFFSET)|
(((u32)(qos_parameters->cw_max[i]))<< AC_PARAM_ECW_MAX_OFFSET)|
(((u32)(qos_parameters->cw_min[i]))<< AC_PARAM_ECW_MIN_OFFSET)|
((u32)u1bAIFS << AC_PARAM_AIFS_OFFSET));
write_nic_dword(dev, WDCAPARA_ADD[i], u4bAcParam);
//write_nic_dword(dev, WDCAPARA_ADD[i], 0x005e4332);
}
success:
mutex_unlock(&priv->mutex);
}
static int rtl8192_qos_handle_probe_response(struct r8192_priv *priv,
int active_network,
struct ieee80211_network *network)
{
int ret = 0;
u32 size = sizeof(struct ieee80211_qos_parameters);
if(priv->ieee80211->state !=IEEE80211_LINKED)
return ret;
if ((priv->ieee80211->iw_mode != IW_MODE_INFRA))
return ret;
if (network->flags & NETWORK_HAS_QOS_MASK) {
if (active_network &&
(network->flags & NETWORK_HAS_QOS_PARAMETERS))
network->qos_data.active = network->qos_data.supported;
if ((network->qos_data.active == 1) && (active_network == 1) &&
(network->flags & NETWORK_HAS_QOS_PARAMETERS) &&
(network->qos_data.old_param_count !=
network->qos_data.param_count)) {
network->qos_data.old_param_count =
network->qos_data.param_count;
queue_work(priv->priv_wq, &priv->qos_activate);
RT_TRACE (COMP_QOS, "QoS parameters change call "
"qos_activate\n");
}
} else {
memcpy(&priv->ieee80211->current_network.qos_data.parameters,\
&def_qos_parameters, size);
if ((network->qos_data.active == 1) && (active_network == 1)) {
queue_work(priv->priv_wq, &priv->qos_activate);
RT_TRACE(COMP_QOS, "QoS was disabled call qos_activate \n");
}
network->qos_data.active = 0;
network->qos_data.supported = 0;
}
return 0;
}
/* handle manage frame frame beacon and probe response */
static int rtl8192_handle_beacon(struct net_device * dev,
struct ieee80211_beacon * beacon,
struct ieee80211_network * network)
{
struct r8192_priv *priv = ieee80211_priv(dev);
rtl8192_qos_handle_probe_response(priv,1,network);
queue_delayed_work(priv->priv_wq, &priv->update_beacon_wq, 0);
return 0;
}
/*
* handling the beaconing responses. if we get different QoS setting
* off the network from the associated setting, adjust the QoS
* setting
*/
static int rtl8192_qos_association_resp(struct r8192_priv *priv,
struct ieee80211_network *network)
{
int ret = 0;
unsigned long flags;
u32 size = sizeof(struct ieee80211_qos_parameters);
int set_qos_param = 0;
if ((priv == NULL) || (network == NULL))
return ret;
if(priv->ieee80211->state !=IEEE80211_LINKED)
return ret;
if ((priv->ieee80211->iw_mode != IW_MODE_INFRA))
return ret;
spin_lock_irqsave(&priv->ieee80211->lock, flags);
if(network->flags & NETWORK_HAS_QOS_PARAMETERS) {
memcpy(&priv->ieee80211->current_network.qos_data.parameters,\
&network->qos_data.parameters,\
sizeof(struct ieee80211_qos_parameters));
priv->ieee80211->current_network.qos_data.active = 1;
{
set_qos_param = 1;
/* update qos parameter for current network */
priv->ieee80211->current_network.qos_data.old_param_count = \
priv->ieee80211->current_network.qos_data.param_count;
priv->ieee80211->current_network.qos_data.param_count = \
network->qos_data.param_count;
}
} else {
memcpy(&priv->ieee80211->current_network.qos_data.parameters,\
&def_qos_parameters, size);
priv->ieee80211->current_network.qos_data.active = 0;
priv->ieee80211->current_network.qos_data.supported = 0;
set_qos_param = 1;
}
spin_unlock_irqrestore(&priv->ieee80211->lock, flags);
RT_TRACE(COMP_QOS, "%s: network->flags = %d,%d\n",__FUNCTION__,network->flags ,priv->ieee80211->current_network.qos_data.active);
if (set_qos_param == 1)
queue_work(priv->priv_wq, &priv->qos_activate);
return ret;
}
static int rtl8192_handle_assoc_response(struct net_device *dev,
struct ieee80211_assoc_response_frame *resp,
struct ieee80211_network *network)
{
struct r8192_priv *priv = ieee80211_priv(dev);
rtl8192_qos_association_resp(priv, network);
return 0;
}
void rtl8192_update_ratr_table(struct net_device* dev)
// POCTET_STRING posLegacyRate,
// u8* pMcsRate)
// PRT_WLAN_STA pEntry)
{
struct r8192_priv* priv = ieee80211_priv(dev);
struct ieee80211_device* ieee = priv->ieee80211;
u8* pMcsRate = ieee->dot11HTOperationalRateSet;
//struct ieee80211_network *net = &ieee->current_network;
u32 ratr_value = 0;
u8 rate_index = 0;
rtl8192_config_rate(dev, (u16*)(&ratr_value));
ratr_value |= (*(u16*)(pMcsRate)) << 12;
// switch (net->mode)
switch (ieee->mode)
{
case IEEE_A:
ratr_value &= 0x00000FF0;
break;
case IEEE_B:
ratr_value &= 0x0000000F;
break;
case IEEE_G:
ratr_value &= 0x00000FF7;
break;
case IEEE_N_24G:
case IEEE_N_5G:
if (ieee->pHTInfo->PeerMimoPs == 0) //MIMO_PS_STATIC
ratr_value &= 0x0007F007;
else{
if (priv->rf_type == RF_1T2R)
ratr_value &= 0x000FF007;
else
ratr_value &= 0x0F81F007;
}
break;
default:
break;
}
ratr_value &= 0x0FFFFFFF;
if(ieee->pHTInfo->bCurTxBW40MHz && ieee->pHTInfo->bCurShortGI40MHz){
ratr_value |= 0x80000000;
}else if(!ieee->pHTInfo->bCurTxBW40MHz && ieee->pHTInfo->bCurShortGI20MHz){
ratr_value |= 0x80000000;
}
write_nic_dword(dev, RATR0+rate_index*4, ratr_value);
write_nic_byte(dev, UFWP, 1);
}
static u8 ccmp_ie[4] = {0x00,0x50,0xf2,0x04};
static u8 ccmp_rsn_ie[4] = {0x00, 0x0f, 0xac, 0x04};
bool GetNmodeSupportBySecCfg8192(struct net_device*dev)
{
struct r8192_priv* priv = ieee80211_priv(dev);
struct ieee80211_device* ieee = priv->ieee80211;
struct ieee80211_network * network = &ieee->current_network;
int wpa_ie_len= ieee->wpa_ie_len;
struct ieee80211_crypt_data* crypt;
int encrypt;
crypt = ieee->crypt[ieee->tx_keyidx];
//we use connecting AP's capability instead of only security config on our driver to distinguish whether it should use N mode or G mode
encrypt = (network->capability & WLAN_CAPABILITY_PRIVACY) || (ieee->host_encrypt && crypt && crypt->ops && (0 == strcmp(crypt->ops->name,"WEP")));
/* simply judge */
if(encrypt && (wpa_ie_len == 0)) {
/* wep encryption, no N mode setting */
return false;
// } else if((wpa_ie_len != 0)&&(memcmp(&(ieee->wpa_ie[14]),ccmp_ie,4))) {
} else if((wpa_ie_len != 0)) {
/* parse pairwise key type */
//if((pairwisekey = WEP40)||(pairwisekey = WEP104)||(pairwisekey = TKIP))
if (((ieee->wpa_ie[0] == 0xdd) && (!memcmp(&(ieee->wpa_ie[14]),ccmp_ie,4))) || ((ieee->wpa_ie[0] == 0x30) && (!memcmp(&ieee->wpa_ie[10],ccmp_rsn_ie, 4))))
return true;
else
return false;
} else {
return true;
}
return true;
}
bool GetHalfNmodeSupportByAPs819xUsb(struct net_device* dev)
{
bool Reval;
struct r8192_priv* priv = ieee80211_priv(dev);
struct ieee80211_device* ieee = priv->ieee80211;
if(ieee->bHalfWirelessN24GMode == true)
Reval = true;
else
Reval = false;
return Reval;
}
void rtl8192_refresh_supportrate(struct r8192_priv* priv)
{
struct ieee80211_device* ieee = priv->ieee80211;
//we donot consider set support rate for ABG mode, only HT MCS rate is set here.
if (ieee->mode == WIRELESS_MODE_N_24G || ieee->mode == WIRELESS_MODE_N_5G)
{
memcpy(ieee->Regdot11HTOperationalRateSet, ieee->RegHTSuppRateSet, 16);
//RT_DEBUG_DATA(COMP_INIT, ieee->RegHTSuppRateSet, 16);
//RT_DEBUG_DATA(COMP_INIT, ieee->Regdot11HTOperationalRateSet, 16);
}
else
memset(ieee->Regdot11HTOperationalRateSet, 0, 16);
return;
}
u8 rtl8192_getSupportedWireleeMode(struct net_device*dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
u8 ret = 0;
switch(priv->rf_chip)
{
case RF_8225:
case RF_8256:
case RF_PSEUDO_11N:
ret = (WIRELESS_MODE_N_24G|WIRELESS_MODE_G|WIRELESS_MODE_B);
break;
case RF_8258:
ret = (WIRELESS_MODE_A|WIRELESS_MODE_N_5G);
break;
default:
ret = WIRELESS_MODE_B;
break;
}
return ret;
}
void rtl8192_SetWirelessMode(struct net_device* dev, u8 wireless_mode)
{
struct r8192_priv *priv = ieee80211_priv(dev);
u8 bSupportMode = rtl8192_getSupportedWireleeMode(dev);
if ((wireless_mode == WIRELESS_MODE_AUTO) || ((wireless_mode&bSupportMode)==0))
{
if(bSupportMode & WIRELESS_MODE_N_24G)
{
wireless_mode = WIRELESS_MODE_N_24G;
}
else if(bSupportMode & WIRELESS_MODE_N_5G)
{
wireless_mode = WIRELESS_MODE_N_5G;
}
else if((bSupportMode & WIRELESS_MODE_A))
{
wireless_mode = WIRELESS_MODE_A;
}
else if((bSupportMode & WIRELESS_MODE_G))
{
wireless_mode = WIRELESS_MODE_G;
}
else if((bSupportMode & WIRELESS_MODE_B))
{
wireless_mode = WIRELESS_MODE_B;
}
else{
RT_TRACE(COMP_ERR, "%s(), No valid wireless mode supported, SupportedWirelessMode(%x)!!!\n", __FUNCTION__,bSupportMode);
wireless_mode = WIRELESS_MODE_B;
}
}
#ifdef TO_DO_LIST //// TODO: this function doesn't work well at this time, we should wait for FPGA
ActUpdateChannelAccessSetting( pAdapter, pHalData->CurrentWirelessMode, &pAdapter->MgntInfo.Info8185.ChannelAccessSetting );
#endif
priv->ieee80211->mode = wireless_mode;
if ((wireless_mode == WIRELESS_MODE_N_24G) || (wireless_mode == WIRELESS_MODE_N_5G))
priv->ieee80211->pHTInfo->bEnableHT = 1;
else
priv->ieee80211->pHTInfo->bEnableHT = 0;
RT_TRACE(COMP_INIT, "Current Wireless Mode is %x\n", wireless_mode);
rtl8192_refresh_supportrate(priv);
}
//init priv variables here. only non_zero value should be initialized here.
static void rtl8192_init_priv_variable(struct net_device* dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
u8 i;
priv->card_8192 = NIC_8192U;
priv->chan = 1; //set to channel 1
priv->ieee80211->mode = WIRELESS_MODE_AUTO; //SET AUTO
priv->ieee80211->iw_mode = IW_MODE_INFRA;
priv->ieee80211->ieee_up=0;
priv->retry_rts = DEFAULT_RETRY_RTS;
priv->retry_data = DEFAULT_RETRY_DATA;
priv->ieee80211->rts = DEFAULT_RTS_THRESHOLD;
priv->ieee80211->rate = 110; //11 mbps
priv->ieee80211->short_slot = 1;
priv->promisc = (dev->flags & IFF_PROMISC) ? 1:0;
priv->CckPwEnl = 6;
//for silent reset
priv->IrpPendingCount = 1;
priv->ResetProgress = RESET_TYPE_NORESET;
priv->bForcedSilentReset = 0;
priv->bDisableNormalResetCheck = false;
priv->force_reset = false;
priv->ieee80211->FwRWRF = 0; //we don't use FW read/write RF until stable firmware is available.
priv->ieee80211->current_network.beacon_interval = DEFAULT_BEACONINTERVAL;
priv->ieee80211->iw_mode = IW_MODE_INFRA;
priv->ieee80211->softmac_features = IEEE_SOFTMAC_SCAN |
IEEE_SOFTMAC_ASSOCIATE | IEEE_SOFTMAC_PROBERQ |
IEEE_SOFTMAC_PROBERS | IEEE_SOFTMAC_TX_QUEUE |
IEEE_SOFTMAC_BEACONS;//added by amy 080604 //| //IEEE_SOFTMAC_SINGLE_QUEUE;
priv->ieee80211->active_scan = 1;
priv->ieee80211->modulation = IEEE80211_CCK_MODULATION | IEEE80211_OFDM_MODULATION;
priv->ieee80211->host_encrypt = 1;
priv->ieee80211->host_decrypt = 1;
priv->ieee80211->start_send_beacons = NULL;//rtl819xusb_beacon_tx;//-by amy 080604
priv->ieee80211->stop_send_beacons = NULL;//rtl8192_beacon_stop;//-by amy 080604
priv->ieee80211->softmac_hard_start_xmit = rtl8192_hard_start_xmit;
priv->ieee80211->set_chan = rtl8192_set_chan;
priv->ieee80211->link_change = rtl8192_link_change;
priv->ieee80211->softmac_data_hard_start_xmit = rtl8192_hard_data_xmit;
priv->ieee80211->data_hard_stop = rtl8192_data_hard_stop;
priv->ieee80211->data_hard_resume = rtl8192_data_hard_resume;
priv->ieee80211->init_wmmparam_flag = 0;
priv->ieee80211->fts = DEFAULT_FRAG_THRESHOLD;
priv->ieee80211->check_nic_enough_desc = check_nic_enough_desc;
priv->ieee80211->tx_headroom = TX_PACKET_SHIFT_BYTES;
priv->ieee80211->qos_support = 1;
//added by WB
// priv->ieee80211->SwChnlByTimerHandler = rtl8192_phy_SwChnl;
priv->ieee80211->SetBWModeHandler = rtl8192_SetBWMode;
priv->ieee80211->handle_assoc_response = rtl8192_handle_assoc_response;
priv->ieee80211->handle_beacon = rtl8192_handle_beacon;
//added by david
priv->ieee80211->GetNmodeSupportBySecCfg = GetNmodeSupportBySecCfg8192;
priv->ieee80211->GetHalfNmodeSupportByAPsHandler = GetHalfNmodeSupportByAPs819xUsb;
priv->ieee80211->SetWirelessMode = rtl8192_SetWirelessMode;
//added by amy
priv->ieee80211->InitialGainHandler = InitialGain819xUsb;
priv->card_type = USB;
#ifdef TO_DO_LIST
if(Adapter->bInHctTest)
{
pHalData->ShortRetryLimit = 7;
pHalData->LongRetryLimit = 7;
}
#endif
{
priv->ShortRetryLimit = 0x30;
priv->LongRetryLimit = 0x30;
}
priv->EarlyRxThreshold = 7;
priv->enable_gpio0 = 0;
priv->TransmitConfig =
// TCR_DurProcMode | //for RTL8185B, duration setting by HW
//? TCR_DISReqQsize |
(TCR_MXDMA_2048<<TCR_MXDMA_OFFSET)| // Max DMA Burst Size per Tx DMA Burst, 7: reservied.
(priv->ShortRetryLimit<<TCR_SRL_OFFSET)| // Short retry limit
(priv->LongRetryLimit<<TCR_LRL_OFFSET) | // Long retry limit
(false ? TCR_SAT: 0); // FALSE: HW provies PLCP length and LENGEXT, TURE: SW proiveds them
#ifdef TO_DO_LIST
if(Adapter->bInHctTest)
pHalData->ReceiveConfig = pHalData->CSMethod |
RCR_AMF | RCR_ADF | //RCR_AAP | //accept management/data
//guangan200710
RCR_ACF | //accept control frame for SW AP needs PS-poll, 2005.07.07, by rcnjko.
RCR_AB | RCR_AM | RCR_APM | //accept BC/MC/UC
RCR_AICV | RCR_ACRC32 | //accept ICV/CRC error packet
((u32)7<<RCR_MXDMA_OFFSET) | // Max DMA Burst Size per Rx DMA Burst, 7: unlimited.
(pHalData->EarlyRxThreshold<<RCR_FIFO_OFFSET) | // Rx FIFO Threshold, 7: No Rx threshold.
(pHalData->EarlyRxThreshold == 7 ? RCR_OnlyErlPkt:0);
else
#endif
priv->ReceiveConfig =
RCR_AMF | RCR_ADF | //accept management/data
RCR_ACF | //accept control frame for SW AP needs PS-poll, 2005.07.07, by rcnjko.
RCR_AB | RCR_AM | RCR_APM | //accept BC/MC/UC
//RCR_AICV | RCR_ACRC32 | //accept ICV/CRC error packet
((u32)7<<RCR_MXDMA_OFFSET)| // Max DMA Burst Size per Rx DMA Burst, 7: unlimited.
(priv->EarlyRxThreshold<<RX_FIFO_THRESHOLD_SHIFT) | // Rx FIFO Threshold, 7: No Rx threshold.
(priv->EarlyRxThreshold == 7 ? RCR_ONLYERLPKT:0);
priv->AcmControl = 0;
priv->pFirmware = kmalloc(sizeof(rt_firmware), GFP_KERNEL);
if (priv->pFirmware)
memset(priv->pFirmware, 0, sizeof(rt_firmware));
/* rx related queue */
skb_queue_head_init(&priv->rx_queue);
skb_queue_head_init(&priv->skb_queue);
/* Tx related queue */
for(i = 0; i < MAX_QUEUE_SIZE; i++) {
skb_queue_head_init(&priv->ieee80211->skb_waitQ [i]);
}
for(i = 0; i < MAX_QUEUE_SIZE; i++) {
skb_queue_head_init(&priv->ieee80211->skb_aggQ [i]);
}
for(i = 0; i < MAX_QUEUE_SIZE; i++) {
skb_queue_head_init(&priv->ieee80211->skb_drv_aggQ [i]);
}
priv->rf_set_chan = rtl8192_phy_SwChnl;
}
//init lock here
static void rtl8192_init_priv_lock(struct r8192_priv* priv)
{
spin_lock_init(&priv->tx_lock);
spin_lock_init(&priv->irq_lock);//added by thomas
//spin_lock_init(&priv->rf_lock);
sema_init(&priv->wx_sem,1);
sema_init(&priv->rf_sem,1);
mutex_init(&priv->mutex);
}
extern void rtl819x_watchdog_wqcallback(struct work_struct *work);
void rtl8192_irq_rx_tasklet(struct r8192_priv *priv);
//init tasklet and wait_queue here. only 2.6 above kernel is considered
#define DRV_NAME "wlan0"
static void rtl8192_init_priv_task(struct net_device* dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
#ifdef PF_SYNCTHREAD
priv->priv_wq = create_workqueue(DRV_NAME,0);
#else
priv->priv_wq = create_workqueue(DRV_NAME);
#endif
INIT_WORK(&priv->reset_wq, rtl8192_restart);
//INIT_DELAYED_WORK(&priv->watch_dog_wq, hal_dm_watchdog);
INIT_DELAYED_WORK(&priv->watch_dog_wq, rtl819x_watchdog_wqcallback);
INIT_DELAYED_WORK(&priv->txpower_tracking_wq, dm_txpower_trackingcallback);
// INIT_DELAYED_WORK(&priv->gpio_change_rf_wq, dm_gpio_change_rf_callback);
INIT_DELAYED_WORK(&priv->rfpath_check_wq, dm_rf_pathcheck_workitemcallback);
INIT_DELAYED_WORK(&priv->update_beacon_wq, rtl8192_update_beacon);
INIT_DELAYED_WORK(&priv->initialgain_operate_wq, InitialGainOperateWorkItemCallBack);
//INIT_WORK(&priv->SwChnlWorkItem, rtl8192_SwChnl_WorkItem);
//INIT_WORK(&priv->SetBWModeWorkItem, rtl8192_SetBWModeWorkItem);
INIT_WORK(&priv->qos_activate, rtl8192_qos_activate);
tasklet_init(&priv->irq_rx_tasklet,
(void(*)(unsigned long))rtl8192_irq_rx_tasklet,
(unsigned long)priv);
}
static void rtl8192_get_eeprom_size(struct net_device* dev)
{
u16 curCR = 0;
struct r8192_priv *priv = ieee80211_priv(dev);
RT_TRACE(COMP_EPROM, "===========>%s()\n", __FUNCTION__);
curCR = read_nic_word_E(dev,EPROM_CMD);
RT_TRACE(COMP_EPROM, "read from Reg EPROM_CMD(%x):%x\n", EPROM_CMD, curCR);
//whether need I consider BIT5?
priv->epromtype = (curCR & Cmd9346CR_9356SEL) ? EPROM_93c56 : EPROM_93c46;
RT_TRACE(COMP_EPROM, "<===========%s(), epromtype:%d\n", __FUNCTION__, priv->epromtype);
}
//used to swap endian. as ntohl & htonl are not necessary to swap endian, so use this instead.
static inline u16 endian_swap(u16* data)
{
u16 tmp = *data;
*data = (tmp >> 8) | (tmp << 8);
return *data;
}
static void rtl8192_read_eeprom_info(struct net_device* dev)
{
u16 wEPROM_ID = 0;
u8 bMac_Tmp_Addr[6] = {0x00, 0xe0, 0x4c, 0x00, 0x00, 0x02};
u8 bLoad_From_EEPOM = false;
struct r8192_priv *priv = ieee80211_priv(dev);
u16 tmpValue = 0;
RT_TRACE(COMP_EPROM, "===========>%s()\n", __FUNCTION__);
wEPROM_ID = eprom_read(dev, 0); //first read EEPROM ID out;
RT_TRACE(COMP_EPROM, "EEPROM ID is 0x%x\n", wEPROM_ID);
if (wEPROM_ID != RTL8190_EEPROM_ID)
{
RT_TRACE(COMP_ERR, "EEPROM ID is invalid(is 0x%x(should be 0x%x)\n", wEPROM_ID, RTL8190_EEPROM_ID);
}
else
bLoad_From_EEPOM = true;
if (bLoad_From_EEPOM)
{
tmpValue = eprom_read(dev, (EEPROM_VID>>1));
priv->eeprom_vid = endian_swap(&tmpValue);
priv->eeprom_pid = eprom_read(dev, (EEPROM_PID>>1));
tmpValue = eprom_read(dev, (EEPROM_ChannelPlan>>1));
priv->eeprom_ChannelPlan =((tmpValue&0xff00)>>8);
priv->btxpowerdata_readfromEEPORM = true;
priv->eeprom_CustomerID = eprom_read(dev, (EEPROM_Customer_ID>>1)) >>8;
}
else
{
priv->eeprom_vid = 0;
priv->eeprom_pid = 0;
priv->card_8192_version = VERSION_819xU_B;
priv->eeprom_ChannelPlan = 0;
priv->eeprom_CustomerID = 0;
}
RT_TRACE(COMP_EPROM, "vid:0x%4x, pid:0x%4x, CustomID:0x%2x, ChanPlan:0x%x\n", priv->eeprom_vid, priv->eeprom_pid, priv->eeprom_CustomerID, priv->eeprom_ChannelPlan);
//set channelplan from eeprom
priv->ChannelPlan = priv->eeprom_ChannelPlan;
if (bLoad_From_EEPOM)
{
int i;
for (i=0; i<6; i+=2)
{
u16 tmp = 0;
tmp = eprom_read(dev, (u16)((EEPROM_NODE_ADDRESS_BYTE_0 + i)>>1));
*(u16*)(&dev->dev_addr[i]) = tmp;
}
}
else
{
memcpy(dev->dev_addr, bMac_Tmp_Addr, 6);
//should I set IDR0 here?
}
RT_TRACE(COMP_EPROM, "MAC addr:%pM\n", dev->dev_addr);
priv->rf_type = RTL819X_DEFAULT_RF_TYPE; //default 1T2R
priv->rf_chip = RF_8256;
if (priv->card_8192_version == (u8)VERSION_819xU_A)
{
//read Tx power gain offset of legacy OFDM to HT rate
if (bLoad_From_EEPOM)
priv->EEPROMTxPowerDiff = (eprom_read(dev, (EEPROM_TxPowerDiff>>1))&0xff00) >> 8;
else
priv->EEPROMTxPowerDiff = EEPROM_Default_TxPower;
RT_TRACE(COMP_EPROM, "TxPowerDiff:%d\n", priv->EEPROMTxPowerDiff);
//read ThermalMeter from EEPROM
if (bLoad_From_EEPOM)
priv->EEPROMThermalMeter = (u8)(eprom_read(dev, (EEPROM_ThermalMeter>>1))&0x00ff);
else
priv->EEPROMThermalMeter = EEPROM_Default_ThermalMeter;
RT_TRACE(COMP_EPROM, "ThermalMeter:%d\n", priv->EEPROMThermalMeter);
//vivi, for tx power track
priv->TSSI_13dBm = priv->EEPROMThermalMeter *100;
//read antenna tx power offset of B/C/D to A from EEPROM
if (bLoad_From_EEPOM)
priv->EEPROMPwDiff = (eprom_read(dev, (EEPROM_PwDiff>>1))&0x0f00)>>8;
else
priv->EEPROMPwDiff = EEPROM_Default_PwDiff;
RT_TRACE(COMP_EPROM, "TxPwDiff:%d\n", priv->EEPROMPwDiff);
// Read CrystalCap from EEPROM
if (bLoad_From_EEPOM)
priv->EEPROMCrystalCap = (eprom_read(dev, (EEPROM_CrystalCap>>1))&0x0f);
else
priv->EEPROMCrystalCap = EEPROM_Default_CrystalCap;
RT_TRACE(COMP_EPROM, "CrystalCap = %d\n", priv->EEPROMCrystalCap);
//get per-channel Tx power level
if (bLoad_From_EEPOM)
priv->EEPROM_Def_Ver = (eprom_read(dev, (EEPROM_TxPwIndex_Ver>>1))&0xff00)>>8;
else
priv->EEPROM_Def_Ver = 1;
RT_TRACE(COMP_EPROM, "EEPROM_DEF_VER:%d\n", priv->EEPROM_Def_Ver);
if (priv->EEPROM_Def_Ver == 0) //old eeprom definition
{
int i;
if (bLoad_From_EEPOM)
priv->EEPROMTxPowerLevelCCK = (eprom_read(dev, (EEPROM_TxPwIndex_CCK>>1))&0xff) >> 8;
else
priv->EEPROMTxPowerLevelCCK = 0x10;
RT_TRACE(COMP_EPROM, "CCK Tx Power Levl: 0x%02x\n", priv->EEPROMTxPowerLevelCCK);
for (i=0; i<3; i++)
{
if (bLoad_From_EEPOM)
{
tmpValue = eprom_read(dev, (EEPROM_TxPwIndex_OFDM_24G+i)>>1);
if (((EEPROM_TxPwIndex_OFDM_24G+i) % 2) == 0)
tmpValue = tmpValue & 0x00ff;
else
tmpValue = (tmpValue & 0xff00) >> 8;
}
else
tmpValue = 0x10;
priv->EEPROMTxPowerLevelOFDM24G[i] = (u8) tmpValue;
RT_TRACE(COMP_EPROM, "OFDM 2.4G Tx Power Level, Index %d = 0x%02x\n", i, priv->EEPROMTxPowerLevelCCK);
}
}//end if EEPROM_DEF_VER == 0
else if (priv->EEPROM_Def_Ver == 1)
{
if (bLoad_From_EEPOM)
{
tmpValue = eprom_read(dev, (EEPROM_TxPwIndex_CCK_V1>>1));
tmpValue = (tmpValue & 0xff00) >> 8;
}
else
tmpValue = 0x10;
priv->EEPROMTxPowerLevelCCK_V1[0] = (u8)tmpValue;
if (bLoad_From_EEPOM)
tmpValue = eprom_read(dev, (EEPROM_TxPwIndex_CCK_V1 + 2)>>1);
else
tmpValue = 0x1010;
*((u16*)(&priv->EEPROMTxPowerLevelCCK_V1[1])) = tmpValue;
if (bLoad_From_EEPOM)
tmpValue = eprom_read(dev, (EEPROM_TxPwIndex_OFDM_24G_V1>>1));
else
tmpValue = 0x1010;
*((u16*)(&priv->EEPROMTxPowerLevelOFDM24G[0])) = tmpValue;
if (bLoad_From_EEPOM)
tmpValue = eprom_read(dev, (EEPROM_TxPwIndex_OFDM_24G_V1+2)>>1);
else
tmpValue = 0x10;
priv->EEPROMTxPowerLevelOFDM24G[2] = (u8)tmpValue;
}//endif EEPROM_Def_Ver == 1
//update HAL variables
//
{
int i;
for (i=0; i<14; i++)
{
if (i<=3)
priv->TxPowerLevelOFDM24G[i] = priv->EEPROMTxPowerLevelOFDM24G[0];
else if (i>=4 && i<=9)
priv->TxPowerLevelOFDM24G[i] = priv->EEPROMTxPowerLevelOFDM24G[1];
else
priv->TxPowerLevelOFDM24G[i] = priv->EEPROMTxPowerLevelOFDM24G[2];
}
for (i=0; i<14; i++)
{
if (priv->EEPROM_Def_Ver == 0)
{
if (i<=3)
priv->TxPowerLevelCCK[i] = priv->EEPROMTxPowerLevelOFDM24G[0] + (priv->EEPROMTxPowerLevelCCK - priv->EEPROMTxPowerLevelOFDM24G[1]);
else if (i>=4 && i<=9)
priv->TxPowerLevelCCK[i] = priv->EEPROMTxPowerLevelCCK;
else
priv->TxPowerLevelCCK[i] = priv->EEPROMTxPowerLevelOFDM24G[2] + (priv->EEPROMTxPowerLevelCCK - priv->EEPROMTxPowerLevelOFDM24G[1]);
}
else if (priv->EEPROM_Def_Ver == 1)
{
if (i<=3)
priv->TxPowerLevelCCK[i] = priv->EEPROMTxPowerLevelCCK_V1[0];
else if (i>=4 && i<=9)
priv->TxPowerLevelCCK[i] = priv->EEPROMTxPowerLevelCCK_V1[1];
else
priv->TxPowerLevelCCK[i] = priv->EEPROMTxPowerLevelCCK_V1[2];
}
}
}//end update HAL variables
priv->TxPowerDiff = priv->EEPROMPwDiff;
// Antenna B gain offset to antenna A, bit0~3
priv->AntennaTxPwDiff[0] = (priv->EEPROMTxPowerDiff & 0xf);
// Antenna C gain offset to antenna A, bit4~7
priv->AntennaTxPwDiff[1] = ((priv->EEPROMTxPowerDiff & 0xf0)>>4);
// CrystalCap, bit12~15
priv->CrystalCap = priv->EEPROMCrystalCap;
// ThermalMeter, bit0~3 for RFIC1, bit4~7 for RFIC2
// 92U does not enable TX power tracking.
priv->ThermalMeter[0] = priv->EEPROMThermalMeter;
}//end if VersionID == VERSION_819xU_A
//added by vivi, for dlink led, 20080416
switch(priv->eeprom_CustomerID)
{
case EEPROM_CID_RUNTOP:
priv->CustomerID = RT_CID_819x_RUNTOP;
break;
case EEPROM_CID_DLINK:
priv->CustomerID = RT_CID_DLINK;
break;
default:
priv->CustomerID = RT_CID_DEFAULT;
break;
}
switch(priv->CustomerID)
{
case RT_CID_819x_RUNTOP:
priv->LedStrategy = SW_LED_MODE2;
break;
case RT_CID_DLINK:
priv->LedStrategy = SW_LED_MODE4;
break;
default:
priv->LedStrategy = SW_LED_MODE0;
break;
}
if(priv->rf_type == RF_1T2R)
{
RT_TRACE(COMP_EPROM, "\n1T2R config\n");
}
else
{
RT_TRACE(COMP_EPROM, "\n2T4R config\n");
}
// 2008/01/16 MH We can only know RF type in the function. So we have to init
// DIG RATR table again.
init_rate_adaptive(dev);
//we need init DIG RATR table here again.
RT_TRACE(COMP_EPROM, "<===========%s()\n", __FUNCTION__);
return;
}
short rtl8192_get_channel_map(struct net_device * dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
if(priv->ChannelPlan > COUNTRY_CODE_GLOBAL_DOMAIN){
printk("rtl8180_init:Error channel plan! Set to default.\n");
priv->ChannelPlan= 0;
}
RT_TRACE(COMP_INIT, "Channel plan is %d\n",priv->ChannelPlan);
rtl819x_set_channel_map(priv->ChannelPlan, priv);
return 0;
}
short rtl8192_init(struct net_device *dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
memset(&(priv->stats),0,sizeof(struct Stats));
memset(priv->txqueue_to_outpipemap,0,9);
#ifdef PIPE12
{
int i=0;
u8 queuetopipe[]={3,2,1,0,4,8,7,6,5};
memcpy(priv->txqueue_to_outpipemap,queuetopipe,9);
/* for(i=0;i<9;i++)
printk("%d ",priv->txqueue_to_outpipemap[i]);
printk("\n");*/
}
#else
{
u8 queuetopipe[]={3,2,1,0,4,4,0,4,4};
memcpy(priv->txqueue_to_outpipemap,queuetopipe,9);
/* for(i=0;i<9;i++)
printk("%d ",priv->txqueue_to_outpipemap[i]);
printk("\n");*/
}
#endif
rtl8192_init_priv_variable(dev);
rtl8192_init_priv_lock(priv);
rtl8192_init_priv_task(dev);
rtl8192_get_eeprom_size(dev);
rtl8192_read_eeprom_info(dev);
rtl8192_get_channel_map(dev);
init_hal_dm(dev);
init_timer(&priv->watch_dog_timer);
priv->watch_dog_timer.data = (unsigned long)dev;
priv->watch_dog_timer.function = watch_dog_timer_callback;
if(rtl8192_usb_initendpoints(dev)!=0){
DMESG("Endopoints initialization failed");
return -ENOMEM;
}
//rtl8192_adapter_start(dev);
#ifdef DEBUG_EPROM
dump_eprom(dev);
#endif
return 0;
}
/******************************************************************************
*function: This function actually only set RRSR, RATR and BW_OPMODE registers
* not to do all the hw config as its name says
* input: net_device dev
* output: none
* return: none
* notice: This part need to modified according to the rate set we filtered
* ****************************************************************************/
void rtl8192_hwconfig(struct net_device* dev)
{
u32 regRATR = 0, regRRSR = 0;
u8 regBwOpMode = 0, regTmp = 0;
struct r8192_priv *priv = ieee80211_priv(dev);
// Set RRSR, RATR, and BW_OPMODE registers
//
switch(priv->ieee80211->mode)
{
case WIRELESS_MODE_B:
regBwOpMode = BW_OPMODE_20MHZ;
regRATR = RATE_ALL_CCK;
regRRSR = RATE_ALL_CCK;
break;
case WIRELESS_MODE_A:
regBwOpMode = BW_OPMODE_5G |BW_OPMODE_20MHZ;
regRATR = RATE_ALL_OFDM_AG;
regRRSR = RATE_ALL_OFDM_AG;
break;
case WIRELESS_MODE_G:
regBwOpMode = BW_OPMODE_20MHZ;
regRATR = RATE_ALL_CCK | RATE_ALL_OFDM_AG;
regRRSR = RATE_ALL_CCK | RATE_ALL_OFDM_AG;
break;
case WIRELESS_MODE_AUTO:
#ifdef TO_DO_LIST
if (Adapter->bInHctTest)
{
regBwOpMode = BW_OPMODE_20MHZ;
regRATR = RATE_ALL_CCK | RATE_ALL_OFDM_AG;
regRRSR = RATE_ALL_CCK | RATE_ALL_OFDM_AG;
}
else
#endif
{
regBwOpMode = BW_OPMODE_20MHZ;
regRATR = RATE_ALL_CCK | RATE_ALL_OFDM_AG | RATE_ALL_OFDM_1SS | RATE_ALL_OFDM_2SS;
regRRSR = RATE_ALL_CCK | RATE_ALL_OFDM_AG;
}
break;
case WIRELESS_MODE_N_24G:
// It support CCK rate by default.
// CCK rate will be filtered out only when associated AP does not support it.
regBwOpMode = BW_OPMODE_20MHZ;
regRATR = RATE_ALL_CCK | RATE_ALL_OFDM_AG | RATE_ALL_OFDM_1SS | RATE_ALL_OFDM_2SS;
regRRSR = RATE_ALL_CCK | RATE_ALL_OFDM_AG;
break;
case WIRELESS_MODE_N_5G:
regBwOpMode = BW_OPMODE_5G;
regRATR = RATE_ALL_OFDM_AG | RATE_ALL_OFDM_1SS | RATE_ALL_OFDM_2SS;
regRRSR = RATE_ALL_OFDM_AG;
break;
}
write_nic_byte(dev, BW_OPMODE, regBwOpMode);
{
u32 ratr_value = 0;
ratr_value = regRATR;
if (priv->rf_type == RF_1T2R)
{
ratr_value &= ~(RATE_ALL_OFDM_2SS);
}
write_nic_dword(dev, RATR0, ratr_value);
write_nic_byte(dev, UFWP, 1);
}
regTmp = read_nic_byte(dev, 0x313);
regRRSR = ((regTmp) << 24) | (regRRSR & 0x00ffffff);
write_nic_dword(dev, RRSR, regRRSR);
//
// Set Retry Limit here
//
write_nic_word(dev, RETRY_LIMIT,
priv->ShortRetryLimit << RETRY_LIMIT_SHORT_SHIFT | \
priv->LongRetryLimit << RETRY_LIMIT_LONG_SHIFT);
// Set Contention Window here
// Set Tx AGC
// Set Tx Antenna including Feedback control
// Set Auto Rate fallback control
}
//InitializeAdapter and PhyCfg
bool rtl8192_adapter_start(struct net_device *dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
u32 dwRegRead = 0;
bool init_status = true;
RT_TRACE(COMP_INIT, "====>%s()\n", __FUNCTION__);
priv->Rf_Mode = RF_OP_By_SW_3wire;
//for ASIC power on sequence
write_nic_byte_E(dev, 0x5f, 0x80);
mdelay(50);
write_nic_byte_E(dev, 0x5f, 0xf0);
write_nic_byte_E(dev, 0x5d, 0x00);
write_nic_byte_E(dev, 0x5e, 0x80);
write_nic_byte(dev, 0x17, 0x37);
mdelay(10);
//#ifdef TO_DO_LIST
priv->pFirmware->firmware_status = FW_STATUS_0_INIT;
//config CPUReset Register
//Firmware Reset or not?
dwRegRead = read_nic_dword(dev, CPU_GEN);
if (priv->pFirmware->firmware_status == FW_STATUS_0_INIT)
dwRegRead |= CPU_GEN_SYSTEM_RESET; //do nothing here?
else if (priv->pFirmware->firmware_status == FW_STATUS_5_READY)
dwRegRead |= CPU_GEN_FIRMWARE_RESET;
else
RT_TRACE(COMP_ERR, "ERROR in %s(): undefined firmware state(%d)\n", __FUNCTION__, priv->pFirmware->firmware_status);
write_nic_dword(dev, CPU_GEN, dwRegRead);
//mdelay(30);
//config BB.
rtl8192_BBConfig(dev);
//Loopback mode or not
priv->LoopbackMode = RTL819xU_NO_LOOPBACK;
// priv->LoopbackMode = RTL819xU_MAC_LOOPBACK;
dwRegRead = read_nic_dword(dev, CPU_GEN);
if (priv->LoopbackMode == RTL819xU_NO_LOOPBACK)
dwRegRead = ((dwRegRead & CPU_GEN_NO_LOOPBACK_MSK) | CPU_GEN_NO_LOOPBACK_SET);
else if (priv->LoopbackMode == RTL819xU_MAC_LOOPBACK)
dwRegRead |= CPU_CCK_LOOPBACK;
else
RT_TRACE(COMP_ERR, "Serious error in %s(): wrong loopback mode setting(%d)\n", __FUNCTION__, priv->LoopbackMode);
write_nic_dword(dev, CPU_GEN, dwRegRead);
//after reset cpu, we need wait for a seconds to write in register.
udelay(500);
//xiong add for new bitfile:usb suspend reset pin set to 1. //do we need?
write_nic_byte_E(dev, 0x5f, (read_nic_byte_E(dev, 0x5f)|0x20));
//Set Hardware
rtl8192_hwconfig(dev);
//turn on Tx/Rx
write_nic_byte(dev, CMDR, CR_RE|CR_TE);
//set IDR0 here
write_nic_dword(dev, MAC0, ((u32*)dev->dev_addr)[0]);
write_nic_word(dev, MAC4, ((u16*)(dev->dev_addr + 4))[0]);
//set RCR
write_nic_dword(dev, RCR, priv->ReceiveConfig);
//Initialize Number of Reserved Pages in Firmware Queue
write_nic_dword(dev, RQPN1, NUM_OF_PAGE_IN_FW_QUEUE_BK << RSVD_FW_QUEUE_PAGE_BK_SHIFT |\
NUM_OF_PAGE_IN_FW_QUEUE_BE << RSVD_FW_QUEUE_PAGE_BE_SHIFT | \
NUM_OF_PAGE_IN_FW_QUEUE_VI << RSVD_FW_QUEUE_PAGE_VI_SHIFT | \
NUM_OF_PAGE_IN_FW_QUEUE_VO <<RSVD_FW_QUEUE_PAGE_VO_SHIFT);
write_nic_dword(dev, RQPN2, NUM_OF_PAGE_IN_FW_QUEUE_MGNT << RSVD_FW_QUEUE_PAGE_MGNT_SHIFT |\
NUM_OF_PAGE_IN_FW_QUEUE_CMD << RSVD_FW_QUEUE_PAGE_CMD_SHIFT);
write_nic_dword(dev, RQPN3, APPLIED_RESERVED_QUEUE_IN_FW| \
NUM_OF_PAGE_IN_FW_QUEUE_BCN<<RSVD_FW_QUEUE_PAGE_BCN_SHIFT
// | NUM_OF_PAGE_IN_FW_QUEUE_PUB<<RSVD_FW_QUEUE_PAGE_PUB_SHIFT
);
write_nic_dword(dev, RATR0+4*7, (RATE_ALL_OFDM_AG | RATE_ALL_CCK));
//Set AckTimeout
// TODO: (it value is only for FPGA version). need to be changed!!2006.12.18, by Emily
write_nic_byte(dev, ACK_TIMEOUT, 0x30);
// RT_TRACE(COMP_INIT, "%s():priv->ResetProgress is %d\n", __FUNCTION__,priv->ResetProgress);
if(priv->ResetProgress == RESET_TYPE_NORESET)
rtl8192_SetWirelessMode(dev, priv->ieee80211->mode);
if(priv->ResetProgress == RESET_TYPE_NORESET){
CamResetAllEntry(dev);
{
u8 SECR_value = 0x0;
SECR_value |= SCR_TxEncEnable;
SECR_value |= SCR_RxDecEnable;
SECR_value |= SCR_NoSKMC;
write_nic_byte(dev, SECR, SECR_value);
}
}
//Beacon related
write_nic_word(dev, ATIMWND, 2);
write_nic_word(dev, BCN_INTERVAL, 100);
{
#define DEFAULT_EDCA 0x005e4332
int i;
for (i=0; i<QOS_QUEUE_NUM; i++)
write_nic_dword(dev, WDCAPARA_ADD[i], DEFAULT_EDCA);
}
#ifdef USB_RX_AGGREGATION_SUPPORT
//3 For usb rx firmware aggregation control
if(priv->ResetProgress == RESET_TYPE_NORESET)
{
u32 ulValue;
PRT_HIGH_THROUGHPUT pHTInfo = priv->ieee80211->pHTInfo;
ulValue = (pHTInfo->UsbRxFwAggrEn<<24) | (pHTInfo->UsbRxFwAggrPageNum<<16) |
(pHTInfo->UsbRxFwAggrPacketNum<<8) | (pHTInfo->UsbRxFwAggrTimeout);
/*
* If usb rx firmware aggregation is enabled,
* when anyone of three threshold conditions above is reached,
* firmware will send aggregated packet to driver.
*/
write_nic_dword(dev, 0x1a8, ulValue);
priv->bCurrentRxAggrEnable = true;
}
#endif
rtl8192_phy_configmac(dev);
if (priv->card_8192_version == (u8) VERSION_819xU_A)
{
rtl8192_phy_getTxPower(dev);
rtl8192_phy_setTxPower(dev, priv->chan);
}
//Firmware download
init_status = init_firmware(dev);
if(!init_status)
{
RT_TRACE(COMP_ERR,"ERR!!! %s(): Firmware download is failed\n", __FUNCTION__);
return init_status;
}
RT_TRACE(COMP_INIT, "%s():after firmware download\n", __FUNCTION__);
//
#ifdef TO_DO_LIST
if(Adapter->ResetProgress == RESET_TYPE_NORESET)
{
if(pMgntInfo->RegRfOff == TRUE)
{ // User disable RF via registry.
RT_TRACE((COMP_INIT|COMP_RF), DBG_LOUD, ("InitializeAdapter819xUsb(): Turn off RF for RegRfOff ----------\n"));
MgntActSet_RF_State(Adapter, eRfOff, RF_CHANGE_BY_SW);
// Those action will be discard in MgntActSet_RF_State because off the same state
for(eRFPath = 0; eRFPath <pHalData->NumTotalRFPath; eRFPath++)
PHY_SetRFReg(Adapter, (RF90_RADIO_PATH_E)eRFPath, 0x4, 0xC00, 0x0);
}
else if(pMgntInfo->RfOffReason > RF_CHANGE_BY_PS)
{ // H/W or S/W RF OFF before sleep.
RT_TRACE((COMP_INIT|COMP_RF), DBG_LOUD, ("InitializeAdapter819xUsb(): Turn off RF for RfOffReason(%d) ----------\n", pMgntInfo->RfOffReason));
MgntActSet_RF_State(Adapter, eRfOff, pMgntInfo->RfOffReason);
}
else
{
pHalData->eRFPowerState = eRfOn;
pMgntInfo->RfOffReason = 0;
RT_TRACE((COMP_INIT|COMP_RF), DBG_LOUD, ("InitializeAdapter819xUsb(): RF is on ----------\n"));
}
}
else
{
if(pHalData->eRFPowerState == eRfOff)
{
MgntActSet_RF_State(Adapter, eRfOff, pMgntInfo->RfOffReason);
// Those action will be discard in MgntActSet_RF_State because off the same state
for(eRFPath = 0; eRFPath <pHalData->NumTotalRFPath; eRFPath++)
PHY_SetRFReg(Adapter, (RF90_RADIO_PATH_E)eRFPath, 0x4, 0xC00, 0x0);
}
}
#endif
//config RF.
if(priv->ResetProgress == RESET_TYPE_NORESET){
rtl8192_phy_RFConfig(dev);
RT_TRACE(COMP_INIT, "%s():after phy RF config\n", __FUNCTION__);
}
if(priv->ieee80211->FwRWRF)
// We can force firmware to do RF-R/W
priv->Rf_Mode = RF_OP_By_FW;
else
priv->Rf_Mode = RF_OP_By_SW_3wire;
rtl8192_phy_updateInitGain(dev);
/*--set CCK and OFDM Block "ON"--*/
rtl8192_setBBreg(dev, rFPGA0_RFMOD, bCCKEn, 0x1);
rtl8192_setBBreg(dev, rFPGA0_RFMOD, bOFDMEn, 0x1);
if(priv->ResetProgress == RESET_TYPE_NORESET)
{
//if D or C cut
u8 tmpvalue = read_nic_byte(dev, 0x301);
if(tmpvalue ==0x03)
{
priv->bDcut = TRUE;
RT_TRACE(COMP_POWER_TRACKING, "D-cut\n");
}
else
{
priv->bDcut = FALSE;
RT_TRACE(COMP_POWER_TRACKING, "C-cut\n");
}
dm_initialize_txpower_tracking(dev);
if(priv->bDcut == TRUE)
{
u32 i, TempCCk;
u32 tmpRegA= rtl8192_QueryBBReg(dev,rOFDM0_XATxIQImbalance,bMaskDWord);
// u32 tmpRegC= rtl8192_QueryBBReg(dev,rOFDM0_XCTxIQImbalance,bMaskDWord);
for(i = 0; i<TxBBGainTableLength; i++)
{
if(tmpRegA == priv->txbbgain_table[i].txbbgain_value)
{
priv->rfa_txpowertrackingindex= (u8)i;
priv->rfa_txpowertrackingindex_real= (u8)i;
priv->rfa_txpowertracking_default= priv->rfa_txpowertrackingindex;
break;
}
}
TempCCk = rtl8192_QueryBBReg(dev, rCCK0_TxFilter1, bMaskByte2);
for(i=0 ; i<CCKTxBBGainTableLength ; i++)
{
if(TempCCk == priv->cck_txbbgain_table[i].ccktxbb_valuearray[0])
{
priv->cck_present_attentuation_20Mdefault=(u8) i;
break;
}
}
priv->cck_present_attentuation_40Mdefault= 0;
priv->cck_present_attentuation_difference= 0;
priv->cck_present_attentuation = priv->cck_present_attentuation_20Mdefault;
// pMgntInfo->bTXPowerTracking = FALSE;//TEMPLY DISABLE
}
}
write_nic_byte(dev, 0x87, 0x0);
return init_status;
}
/* this configures registers for beacon tx and enables it via
* rtl8192_beacon_tx_enable(). rtl8192_beacon_tx_disable() might
* be used to stop beacon transmission
*/
/***************************************************************************
-------------------------------NET STUFF---------------------------
***************************************************************************/
static struct net_device_stats *rtl8192_stats(struct net_device *dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
return &priv->ieee80211->stats;
}
bool
HalTxCheckStuck819xUsb(
struct net_device *dev
)
{
struct r8192_priv *priv = ieee80211_priv(dev);
u16 RegTxCounter = read_nic_word(dev, 0x128);
bool bStuck = FALSE;
RT_TRACE(COMP_RESET,"%s():RegTxCounter is %d,TxCounter is %d\n",__FUNCTION__,RegTxCounter,priv->TxCounter);
if(priv->TxCounter==RegTxCounter)
bStuck = TRUE;
priv->TxCounter = RegTxCounter;
return bStuck;
}
/*
* <Assumption: RT_TX_SPINLOCK is acquired.>
* First added: 2006.11.19 by emily
*/
RESET_TYPE
TxCheckStuck(struct net_device *dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
u8 QueueID;
// PRT_TCB pTcb;
// u8 ResetThreshold;
bool bCheckFwTxCnt = false;
//unsigned long flags;
//
// Decide Stuch threshold according to current power save mode
//
// RT_TRACE(COMP_RESET, " ==> TxCheckStuck()\n");
// PlatformAcquireSpinLock(Adapter, RT_TX_SPINLOCK);
// spin_lock_irqsave(&priv->ieee80211->lock,flags);
for (QueueID = 0; QueueID<=BEACON_QUEUE;QueueID ++)
{
if(QueueID == TXCMD_QUEUE)
continue;
#ifdef USB_TX_DRIVER_AGGREGATION_ENABLE
if((skb_queue_len(&priv->ieee80211->skb_waitQ[QueueID]) == 0) && (skb_queue_len(&priv->ieee80211->skb_aggQ[QueueID]) == 0) && (skb_queue_len(&priv->ieee80211->skb_drv_aggQ[QueueID]) == 0))
#else
if((skb_queue_len(&priv->ieee80211->skb_waitQ[QueueID]) == 0) && (skb_queue_len(&priv->ieee80211->skb_aggQ[QueueID]) == 0))
#endif
continue;
bCheckFwTxCnt = true;
}
// PlatformReleaseSpinLock(Adapter, RT_TX_SPINLOCK);
// spin_unlock_irqrestore(&priv->ieee80211->lock,flags);
// RT_TRACE(COMP_RESET,"bCheckFwTxCnt is %d\n",bCheckFwTxCnt);
if(bCheckFwTxCnt)
{
if(HalTxCheckStuck819xUsb(dev))
{
RT_TRACE(COMP_RESET, "TxCheckStuck(): Fw indicates no Tx condition! \n");
return RESET_TYPE_SILENT;
}
}
return RESET_TYPE_NORESET;
}
bool
HalRxCheckStuck819xUsb(struct net_device *dev)
{
u16 RegRxCounter = read_nic_word(dev, 0x130);
struct r8192_priv *priv = ieee80211_priv(dev);
bool bStuck = FALSE;
static u8 rx_chk_cnt = 0;
RT_TRACE(COMP_RESET,"%s(): RegRxCounter is %d,RxCounter is %d\n",__FUNCTION__,RegRxCounter,priv->RxCounter);
// If rssi is small, we should check rx for long time because of bad rx.
// or maybe it will continuous silent reset every 2 seconds.
rx_chk_cnt++;
if(priv->undecorated_smoothed_pwdb >= (RateAdaptiveTH_High+5))
{
rx_chk_cnt = 0; //high rssi, check rx stuck right now.
}
else if(priv->undecorated_smoothed_pwdb < (RateAdaptiveTH_High+5) &&
((priv->CurrentChannelBW!=HT_CHANNEL_WIDTH_20&&priv->undecorated_smoothed_pwdb>=RateAdaptiveTH_Low_40M) ||
(priv->CurrentChannelBW==HT_CHANNEL_WIDTH_20&&priv->undecorated_smoothed_pwdb>=RateAdaptiveTH_Low_20M)) )
{
if(rx_chk_cnt < 2)
{
return bStuck;
}
else
{
rx_chk_cnt = 0;
}
}
else if(((priv->CurrentChannelBW!=HT_CHANNEL_WIDTH_20&&priv->undecorated_smoothed_pwdb<RateAdaptiveTH_Low_40M) ||
(priv->CurrentChannelBW==HT_CHANNEL_WIDTH_20&&priv->undecorated_smoothed_pwdb<RateAdaptiveTH_Low_20M)) &&
priv->undecorated_smoothed_pwdb >= VeryLowRSSI)
{
if(rx_chk_cnt < 4)
{
//DbgPrint("RSSI < %d && RSSI >= %d, no check this time \n", RateAdaptiveTH_Low, VeryLowRSSI);
return bStuck;
}
else
{
rx_chk_cnt = 0;
//DbgPrint("RSSI < %d && RSSI >= %d, check this time \n", RateAdaptiveTH_Low, VeryLowRSSI);
}
}
else
{
if(rx_chk_cnt < 8)
{
//DbgPrint("RSSI <= %d, no check this time \n", VeryLowRSSI);
return bStuck;
}
else
{
rx_chk_cnt = 0;
//DbgPrint("RSSI <= %d, check this time \n", VeryLowRSSI);
}
}
if(priv->RxCounter==RegRxCounter)
bStuck = TRUE;
priv->RxCounter = RegRxCounter;
return bStuck;
}
RESET_TYPE
RxCheckStuck(struct net_device *dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
//int i;
bool bRxCheck = FALSE;
// RT_TRACE(COMP_RESET," ==> RxCheckStuck()\n");
//PlatformAcquireSpinLock(Adapter, RT_RX_SPINLOCK);
if(priv->IrpPendingCount > 1)
bRxCheck = TRUE;
//PlatformReleaseSpinLock(Adapter, RT_RX_SPINLOCK);
// RT_TRACE(COMP_RESET,"bRxCheck is %d \n",bRxCheck);
if(bRxCheck)
{
if(HalRxCheckStuck819xUsb(dev))
{
RT_TRACE(COMP_RESET, "RxStuck Condition\n");
return RESET_TYPE_SILENT;
}
}
return RESET_TYPE_NORESET;
}
/**
* This function is called by Checkforhang to check whether we should ask OS to reset driver
*
* \param pAdapter The adapter context for this miniport
*
* Note:NIC with USB interface sholud not call this function because we cannot scan descriptor
* to judge whether there is tx stuck.
* Note: This function may be required to be rewrite for Vista OS.
* <<<Assumption: Tx spinlock has been acquired >>>
*
* 8185 and 8185b does not implement this function. This is added by Emily at 2006.11.24
*/
RESET_TYPE
rtl819x_ifcheck_resetornot(struct net_device *dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
RESET_TYPE TxResetType = RESET_TYPE_NORESET;
RESET_TYPE RxResetType = RESET_TYPE_NORESET;
RT_RF_POWER_STATE rfState;
rfState = priv->ieee80211->eRFPowerState;
TxResetType = TxCheckStuck(dev);
if( rfState != eRfOff ||
/*ADAPTER_TEST_STATUS_FLAG(Adapter, ADAPTER_STATUS_FW_DOWNLOAD_FAILURE)) &&*/
(priv->ieee80211->iw_mode != IW_MODE_ADHOC))
{
// If driver is in the status of firmware download failure , driver skips RF initialization and RF is
// in turned off state. Driver should check whether Rx stuck and do silent reset. And
// if driver is in firmware download failure status, driver should initialize RF in the following
// silent reset procedure Emily, 2008.01.21
// Driver should not check RX stuck in IBSS mode because it is required to
// set Check BSSID in order to send beacon, however, if check BSSID is
// set, STA cannot hear any packet a all. Emily, 2008.04.12
RxResetType = RxCheckStuck(dev);
}
if(TxResetType==RESET_TYPE_NORMAL || RxResetType==RESET_TYPE_NORMAL)
return RESET_TYPE_NORMAL;
else if(TxResetType==RESET_TYPE_SILENT || RxResetType==RESET_TYPE_SILENT){
RT_TRACE(COMP_RESET,"%s():silent reset\n",__FUNCTION__);
return RESET_TYPE_SILENT;
}
else
return RESET_TYPE_NORESET;
}
void rtl8192_cancel_deferred_work(struct r8192_priv* priv);
int _rtl8192_up(struct net_device *dev);
int rtl8192_close(struct net_device *dev);
void
CamRestoreAllEntry( struct net_device *dev)
{
u8 EntryId = 0;
struct r8192_priv *priv = ieee80211_priv(dev);
u8* MacAddr = priv->ieee80211->current_network.bssid;
static u8 CAM_CONST_ADDR[4][6] = {
{0x00, 0x00, 0x00, 0x00, 0x00, 0x00},
{0x00, 0x00, 0x00, 0x00, 0x00, 0x01},
{0x00, 0x00, 0x00, 0x00, 0x00, 0x02},
{0x00, 0x00, 0x00, 0x00, 0x00, 0x03}};
static u8 CAM_CONST_BROAD[] =
{0xff, 0xff, 0xff, 0xff, 0xff, 0xff};
RT_TRACE(COMP_SEC, "CamRestoreAllEntry: \n");
if ((priv->ieee80211->pairwise_key_type == KEY_TYPE_WEP40)||
(priv->ieee80211->pairwise_key_type == KEY_TYPE_WEP104))
{
for(EntryId=0; EntryId<4; EntryId++)
{
{
MacAddr = CAM_CONST_ADDR[EntryId];
setKey(dev,
EntryId ,
EntryId,
priv->ieee80211->pairwise_key_type,
MacAddr,
0,
NULL);
}
}
}
else if(priv->ieee80211->pairwise_key_type == KEY_TYPE_TKIP)
{
{
if(priv->ieee80211->iw_mode == IW_MODE_ADHOC)
setKey(dev,
4,
0,
priv->ieee80211->pairwise_key_type,
(u8*)dev->dev_addr,
0,
NULL);
else
setKey(dev,
4,
0,
priv->ieee80211->pairwise_key_type,
MacAddr,
0,
NULL);
}
}
else if(priv->ieee80211->pairwise_key_type == KEY_TYPE_CCMP)
{
{
if(priv->ieee80211->iw_mode == IW_MODE_ADHOC)
setKey(dev,
4,
0,
priv->ieee80211->pairwise_key_type,
(u8*)dev->dev_addr,
0,
NULL);
else
setKey(dev,
4,
0,
priv->ieee80211->pairwise_key_type,
MacAddr,
0,
NULL);
}
}
if(priv->ieee80211->group_key_type == KEY_TYPE_TKIP)
{
MacAddr = CAM_CONST_BROAD;
for(EntryId=1 ; EntryId<4 ; EntryId++)
{
{
setKey(dev,
EntryId,
EntryId,
priv->ieee80211->group_key_type,
MacAddr,
0,
NULL);
}
}
if(priv->ieee80211->iw_mode == IW_MODE_ADHOC)
setKey(dev,
0,
0,
priv->ieee80211->group_key_type,
CAM_CONST_ADDR[0],
0,
NULL);
}
else if(priv->ieee80211->group_key_type == KEY_TYPE_CCMP)
{
MacAddr = CAM_CONST_BROAD;
for(EntryId=1; EntryId<4 ; EntryId++)
{
{
setKey(dev,
EntryId ,
EntryId,
priv->ieee80211->group_key_type,
MacAddr,
0,
NULL);
}
}
if(priv->ieee80211->iw_mode == IW_MODE_ADHOC)
setKey(dev,
0 ,
0,
priv->ieee80211->group_key_type,
CAM_CONST_ADDR[0],
0,
NULL);
}
}
//////////////////////////////////////////////////////////////
// This function is used to fix Tx/Rx stop bug temporarily.
// This function will do "system reset" to NIC when Tx or Rx is stuck.
// The method checking Tx/Rx stuck of this function is supported by FW,
// which reports Tx and Rx counter to register 0x128 and 0x130.
//////////////////////////////////////////////////////////////
void
rtl819x_ifsilentreset(struct net_device *dev)
{
//OCTET_STRING asocpdu;
struct r8192_priv *priv = ieee80211_priv(dev);
u8 reset_times = 0;
int reset_status = 0;
struct ieee80211_device *ieee = priv->ieee80211;
// 2007.07.20. If we need to check CCK stop, please uncomment this line.
//bStuck = Adapter->HalFunc.CheckHWStopHandler(Adapter);
if(priv->ResetProgress==RESET_TYPE_NORESET)
{
RESET_START:
RT_TRACE(COMP_RESET,"=========>Reset progress!! \n");
// Set the variable for reset.
priv->ResetProgress = RESET_TYPE_SILENT;
// rtl8192_close(dev);
down(&priv->wx_sem);
if(priv->up == 0)
{
RT_TRACE(COMP_ERR,"%s():the driver is not up! return\n",__FUNCTION__);
up(&priv->wx_sem);
return ;
}
priv->up = 0;
RT_TRACE(COMP_RESET,"%s():======>start to down the driver\n",__FUNCTION__);
// if(!netif_queue_stopped(dev))
// netif_stop_queue(dev);
rtl8192_rtx_disable(dev);
rtl8192_cancel_deferred_work(priv);
deinit_hal_dm(dev);
del_timer_sync(&priv->watch_dog_timer);
ieee->sync_scan_hurryup = 1;
if(ieee->state == IEEE80211_LINKED)
{
down(&ieee->wx_sem);
printk("ieee->state is IEEE80211_LINKED\n");
ieee80211_stop_send_beacons(priv->ieee80211);
del_timer_sync(&ieee->associate_timer);
cancel_delayed_work(&ieee->associate_retry_wq);
ieee80211_stop_scan(ieee);
netif_carrier_off(dev);
up(&ieee->wx_sem);
}
else{
printk("ieee->state is NOT LINKED\n");
ieee80211_softmac_stop_protocol(priv->ieee80211); }
up(&priv->wx_sem);
RT_TRACE(COMP_RESET,"%s():<==========down process is finished\n",__FUNCTION__);
//rtl8192_irq_disable(dev);
RT_TRACE(COMP_RESET,"%s():===========>start to up the driver\n",__FUNCTION__);
reset_status = _rtl8192_up(dev);
RT_TRACE(COMP_RESET,"%s():<===========up process is finished\n",__FUNCTION__);
if(reset_status == -EAGAIN)
{
if(reset_times < 3)
{
reset_times++;
goto RESET_START;
}
else
{
RT_TRACE(COMP_ERR," ERR!!! %s(): Reset Failed!!\n", __FUNCTION__);
}
}
ieee->is_silent_reset = 1;
EnableHWSecurityConfig8192(dev);
if(ieee->state == IEEE80211_LINKED && ieee->iw_mode == IW_MODE_INFRA)
{
ieee->set_chan(ieee->dev, ieee->current_network.channel);
queue_work(ieee->wq, &ieee->associate_complete_wq);
}
else if(ieee->state == IEEE80211_LINKED && ieee->iw_mode == IW_MODE_ADHOC)
{
ieee->set_chan(ieee->dev, ieee->current_network.channel);
ieee->link_change(ieee->dev);
// notify_wx_assoc_event(ieee);
ieee80211_start_send_beacons(ieee);
if (ieee->data_hard_resume)
ieee->data_hard_resume(ieee->dev);
netif_carrier_on(ieee->dev);
}
CamRestoreAllEntry(dev);
priv->ResetProgress = RESET_TYPE_NORESET;
priv->reset_count++;
priv->bForcedSilentReset =false;
priv->bResetInProgress = false;
// For test --> force write UFWP.
write_nic_byte(dev, UFWP, 1);
RT_TRACE(COMP_RESET, "Reset finished!! ====>[%d]\n", priv->reset_count);
}
}
void CAM_read_entry(
struct net_device *dev,
u32 iIndex
)
{
u32 target_command=0;
u32 target_content=0;
u8 entry_i=0;
u32 ulStatus;
s32 i=100;
// printk("=======>start read CAM\n");
for(entry_i=0;entry_i<CAM_CONTENT_COUNT;entry_i++)
{
// polling bit, and No Write enable, and address
target_command= entry_i+CAM_CONTENT_COUNT*iIndex;
target_command= target_command | BIT31;
//Check polling bit is clear
// mdelay(1);
while((i--)>=0)
{
ulStatus = read_nic_dword(dev, RWCAM);
if(ulStatus & BIT31){
continue;
}
else{
break;
}
}
write_nic_dword(dev, RWCAM, target_command);
RT_TRACE(COMP_SEC,"CAM_read_entry(): WRITE A0: %x \n",target_command);
// printk("CAM_read_entry(): WRITE A0: %lx \n",target_command);
target_content = read_nic_dword(dev, RCAMO);
RT_TRACE(COMP_SEC, "CAM_read_entry(): WRITE A8: %x \n",target_content);
// printk("CAM_read_entry(): WRITE A8: %lx \n",target_content);
}
printk("\n");
}
void rtl819x_update_rxcounts(
struct r8192_priv *priv,
u32* TotalRxBcnNum,
u32* TotalRxDataNum
)
{
u16 SlotIndex;
u8 i;
*TotalRxBcnNum = 0;
*TotalRxDataNum = 0;
SlotIndex = (priv->ieee80211->LinkDetectInfo.SlotIndex++)%(priv->ieee80211->LinkDetectInfo.SlotNum);
priv->ieee80211->LinkDetectInfo.RxBcnNum[SlotIndex] = priv->ieee80211->LinkDetectInfo.NumRecvBcnInPeriod;
priv->ieee80211->LinkDetectInfo.RxDataNum[SlotIndex] = priv->ieee80211->LinkDetectInfo.NumRecvDataInPeriod;
for( i=0; i<priv->ieee80211->LinkDetectInfo.SlotNum; i++ ){
*TotalRxBcnNum += priv->ieee80211->LinkDetectInfo.RxBcnNum[i];
*TotalRxDataNum += priv->ieee80211->LinkDetectInfo.RxDataNum[i];
}
}
extern void rtl819x_watchdog_wqcallback(struct work_struct *work)
{
struct delayed_work *dwork = container_of(work,struct delayed_work,work);
struct r8192_priv *priv = container_of(dwork,struct r8192_priv,watch_dog_wq);
struct net_device *dev = priv->ieee80211->dev;
struct ieee80211_device* ieee = priv->ieee80211;
RESET_TYPE ResetType = RESET_TYPE_NORESET;
static u8 check_reset_cnt=0;
bool bBusyTraffic = false;
if(!priv->up)
return;
hal_dm_watchdog(dev);
{//to get busy traffic condition
if(ieee->state == IEEE80211_LINKED)
{
if( ieee->LinkDetectInfo.NumRxOkInPeriod> 666 ||
ieee->LinkDetectInfo.NumTxOkInPeriod> 666 ) {
bBusyTraffic = true;
}
ieee->LinkDetectInfo.NumRxOkInPeriod = 0;
ieee->LinkDetectInfo.NumTxOkInPeriod = 0;
ieee->LinkDetectInfo.bBusyTraffic = bBusyTraffic;
}
}
//added by amy for AP roaming
{
if(priv->ieee80211->state == IEEE80211_LINKED && priv->ieee80211->iw_mode == IW_MODE_INFRA)
{
u32 TotalRxBcnNum = 0;
u32 TotalRxDataNum = 0;
rtl819x_update_rxcounts(priv, &TotalRxBcnNum, &TotalRxDataNum);
if((TotalRxBcnNum+TotalRxDataNum) == 0)
{
#ifdef TODO
if(rfState == eRfOff)
RT_TRACE(COMP_ERR,"========>%s()\n",__FUNCTION__);
#endif
printk("===>%s(): AP is power off,connect another one\n",__FUNCTION__);
// Dot11d_Reset(dev);
priv->ieee80211->state = IEEE80211_ASSOCIATING;
notify_wx_assoc_event(priv->ieee80211);
RemovePeerTS(priv->ieee80211,priv->ieee80211->current_network.bssid);
priv->ieee80211->link_change(dev);
queue_work(priv->ieee80211->wq, &priv->ieee80211->associate_procedure_wq);
}
}
priv->ieee80211->LinkDetectInfo.NumRecvBcnInPeriod=0;
priv->ieee80211->LinkDetectInfo.NumRecvDataInPeriod=0;
}
// CAM_read_entry(dev,4);
//check if reset the driver
if(check_reset_cnt++ >= 3)
{
ResetType = rtl819x_ifcheck_resetornot(dev);
check_reset_cnt = 3;
//DbgPrint("Start to check silent reset\n");
}
// RT_TRACE(COMP_RESET,"%s():priv->force_reset is %d,priv->ResetProgress is %d, priv->bForcedSilentReset is %d,priv->bDisableNormalResetCheck is %d,ResetType is %d\n",__FUNCTION__,priv->force_reset,priv->ResetProgress,priv->bForcedSilentReset,priv->bDisableNormalResetCheck,ResetType);
if( (priv->force_reset) || (priv->ResetProgress==RESET_TYPE_NORESET &&
(priv->bForcedSilentReset ||
(!priv->bDisableNormalResetCheck && ResetType==RESET_TYPE_SILENT)))) // This is control by OID set in Pomelo
{
RT_TRACE(COMP_RESET,"%s():priv->force_reset is %d,priv->ResetProgress is %d, priv->bForcedSilentReset is %d,priv->bDisableNormalResetCheck is %d,ResetType is %d\n",__FUNCTION__,priv->force_reset,priv->ResetProgress,priv->bForcedSilentReset,priv->bDisableNormalResetCheck,ResetType);
rtl819x_ifsilentreset(dev);
}
priv->force_reset = false;
priv->bForcedSilentReset = false;
priv->bResetInProgress = false;
RT_TRACE(COMP_TRACE, " <==RtUsbCheckForHangWorkItemCallback()\n");
}
void watch_dog_timer_callback(unsigned long data)
{
struct r8192_priv *priv = ieee80211_priv((struct net_device *) data);
//printk("===============>watch_dog timer\n");
queue_delayed_work(priv->priv_wq,&priv->watch_dog_wq, 0);
mod_timer(&priv->watch_dog_timer, jiffies + MSECS(IEEE80211_WATCH_DOG_TIME));
}
int _rtl8192_up(struct net_device *dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
//int i;
int init_status = 0;
priv->up=1;
priv->ieee80211->ieee_up=1;
RT_TRACE(COMP_INIT, "Bringing up iface");
init_status = rtl8192_adapter_start(dev);
if(!init_status)
{
RT_TRACE(COMP_ERR,"ERR!!! %s(): initialization is failed!\n", __FUNCTION__);
priv->up=priv->ieee80211->ieee_up = 0;
return -EAGAIN;
}
RT_TRACE(COMP_INIT, "start adapter finished\n");
rtl8192_rx_enable(dev);
// rtl8192_tx_enable(dev);
if(priv->ieee80211->state != IEEE80211_LINKED)
ieee80211_softmac_start_protocol(priv->ieee80211);
ieee80211_reset_queue(priv->ieee80211);
watch_dog_timer_callback((unsigned long) dev);
if(!netif_queue_stopped(dev))
netif_start_queue(dev);
else
netif_wake_queue(dev);
return 0;
}
int rtl8192_open(struct net_device *dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
int ret;
down(&priv->wx_sem);
ret = rtl8192_up(dev);
up(&priv->wx_sem);
return ret;
}
int rtl8192_up(struct net_device *dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
if (priv->up == 1) return -1;
return _rtl8192_up(dev);
}
int rtl8192_close(struct net_device *dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
int ret;
down(&priv->wx_sem);
ret = rtl8192_down(dev);
up(&priv->wx_sem);
return ret;
}
int rtl8192_down(struct net_device *dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
int i;
if (priv->up == 0) return -1;
priv->up=0;
priv->ieee80211->ieee_up = 0;
RT_TRACE(COMP_DOWN, "==========>%s()\n", __FUNCTION__);
/* FIXME */
if (!netif_queue_stopped(dev))
netif_stop_queue(dev);
rtl8192_rtx_disable(dev);
//rtl8192_irq_disable(dev);
/* Tx related queue release */
for(i = 0; i < MAX_QUEUE_SIZE; i++) {
skb_queue_purge(&priv->ieee80211->skb_waitQ [i]);
}
for(i = 0; i < MAX_QUEUE_SIZE; i++) {
skb_queue_purge(&priv->ieee80211->skb_aggQ [i]);
}
for(i = 0; i < MAX_QUEUE_SIZE; i++) {
skb_queue_purge(&priv->ieee80211->skb_drv_aggQ [i]);
}
//as cancel_delayed_work will del work->timer, so if work is not definedas struct delayed_work, it will corrupt
// flush_scheduled_work();
rtl8192_cancel_deferred_work(priv);
deinit_hal_dm(dev);
del_timer_sync(&priv->watch_dog_timer);
ieee80211_softmac_stop_protocol(priv->ieee80211);
memset(&priv->ieee80211->current_network, 0 , offsetof(struct ieee80211_network, list));
RT_TRACE(COMP_DOWN, "<==========%s()\n", __FUNCTION__);
return 0;
}
void rtl8192_commit(struct net_device *dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
int reset_status = 0;
//u8 reset_times = 0;
if (priv->up == 0) return ;
priv->up = 0;
rtl8192_cancel_deferred_work(priv);
del_timer_sync(&priv->watch_dog_timer);
//cancel_delayed_work(&priv->SwChnlWorkItem);
ieee80211_softmac_stop_protocol(priv->ieee80211);
//rtl8192_irq_disable(dev);
rtl8192_rtx_disable(dev);
reset_status = _rtl8192_up(dev);
}
/*
void rtl8192_restart(struct net_device *dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
*/
void rtl8192_restart(struct work_struct *work)
{
struct r8192_priv *priv = container_of(work, struct r8192_priv, reset_wq);
struct net_device *dev = priv->ieee80211->dev;
down(&priv->wx_sem);
rtl8192_commit(dev);
up(&priv->wx_sem);
}
static void r8192_set_multicast(struct net_device *dev)
{
struct r8192_priv *priv = ieee80211_priv(dev);
short promisc;
//down(&priv->wx_sem);
/* FIXME FIXME */
promisc = (dev->flags & IFF_PROMISC) ? 1:0;
if (promisc != priv->promisc)
// rtl8192_commit(dev);
priv->promisc = promisc;
//schedule_work(&priv->reset_wq);
//up(&priv->wx_sem);
}
int r8192_set_mac_adr(struct net_device *dev, void *mac)
{
struct r8192_priv *priv = ieee80211_priv(dev);
struct sockaddr *addr = mac;
down(&priv->wx_sem);
memcpy(dev->dev_addr, addr->sa_data, ETH_ALEN);
schedule_work(&priv->reset_wq);
up(&priv->wx_sem);
return 0;
}
/* based on ipw2200 driver */
int rtl8192_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
{
struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
struct iwreq *wrq = (struct iwreq *)rq;
int ret=-1;
struct ieee80211_device *ieee = priv->ieee80211;
u32 key[4];
u8 broadcast_addr[6] = {0xff,0xff,0xff,0xff,0xff,0xff};
struct iw_point *p = &wrq->u.data;
struct ieee_param *ipw = NULL;//(struct ieee_param *)wrq->u.data.pointer;
down(&priv->wx_sem);
if (p->length < sizeof(struct ieee_param) || !p->pointer){
ret = -EINVAL;
goto out;
}
ipw = kmalloc(p->length, GFP_KERNEL);
if (ipw == NULL){
ret = -ENOMEM;
goto out;
}
if (copy_from_user(ipw, p->pointer, p->length)) {
kfree(ipw);
ret = -EFAULT;
goto out;
}
switch (cmd) {
case RTL_IOCTL_WPA_SUPPLICANT:
//parse here for HW security
if (ipw->cmd == IEEE_CMD_SET_ENCRYPTION)
{
if (ipw->u.crypt.set_tx)
{
if (strcmp(ipw->u.crypt.alg, "CCMP") == 0)
ieee->pairwise_key_type = KEY_TYPE_CCMP;
else if (strcmp(ipw->u.crypt.alg, "TKIP") == 0)
ieee->pairwise_key_type = KEY_TYPE_TKIP;
else if (strcmp(ipw->u.crypt.alg, "WEP") == 0)
{
if (ipw->u.crypt.key_len == 13)
ieee->pairwise_key_type = KEY_TYPE_WEP104;
else if (ipw->u.crypt.key_len == 5)
ieee->pairwise_key_type = KEY_TYPE_WEP40;
}
else
ieee->pairwise_key_type = KEY_TYPE_NA;
if (ieee->pairwise_key_type)
{
memcpy((u8*)key, ipw->u.crypt.key, 16);
EnableHWSecurityConfig8192(dev);
//we fill both index entry and 4th entry for pairwise key as in IPW interface, adhoc will only get here, so we need index entry for its default key serching!
//added by WB.
setKey(dev, 4, ipw->u.crypt.idx, ieee->pairwise_key_type, (u8*)ieee->ap_mac_addr, 0, key);
if (ieee->auth_mode != 2)
setKey(dev, ipw->u.crypt.idx, ipw->u.crypt.idx, ieee->pairwise_key_type, (u8*)ieee->ap_mac_addr, 0, key);
}
}
else //if (ipw->u.crypt.idx) //group key use idx > 0
{
memcpy((u8*)key, ipw->u.crypt.key, 16);
if (strcmp(ipw->u.crypt.alg, "CCMP") == 0)
ieee->group_key_type= KEY_TYPE_CCMP;
else if (strcmp(ipw->u.crypt.alg, "TKIP") == 0)
ieee->group_key_type = KEY_TYPE_TKIP;
else if (strcmp(ipw->u.crypt.alg, "WEP") == 0)
{
if (ipw->u.crypt.key_len == 13)
ieee->group_key_type = KEY_TYPE_WEP104;
else if (ipw->u.crypt.key_len == 5)
ieee->group_key_type = KEY_TYPE_WEP40;
}
else
ieee->group_key_type = KEY_TYPE_NA;
if (ieee->group_key_type)
{
setKey( dev,
ipw->u.crypt.idx,
ipw->u.crypt.idx, //KeyIndex
ieee->group_key_type, //KeyType
broadcast_addr, //MacAddr
0, //DefaultKey
key); //KeyContent
}
}
}
#ifdef JOHN_HWSEC_DEBUG
//john's test 0711
printk("@@ wrq->u pointer = ");
for(i=0;i<wrq->u.data.length;i++){
if(i%10==0) printk("\n");
printk( "%8x|", ((u32*)wrq->u.data.pointer)[i] );
}
printk("\n");
#endif /*JOHN_HWSEC_DEBUG*/
ret = ieee80211_wpa_supplicant_ioctl(priv->ieee80211, &wrq->u.data);
break;
default:
ret = -EOPNOTSUPP;
break;
}
kfree(ipw);
ipw = NULL;
out:
up(&priv->wx_sem);
return ret;
}
u8 HwRateToMRate90(bool bIsHT, u8 rate)
{
u8 ret_rate = 0xff;
if(!bIsHT) {
switch(rate) {
case DESC90_RATE1M: ret_rate = MGN_1M; break;
case DESC90_RATE2M: ret_rate = MGN_2M; break;
case DESC90_RATE5_5M: ret_rate = MGN_5_5M; break;
case DESC90_RATE11M: ret_rate = MGN_11M; break;
case DESC90_RATE6M: ret_rate = MGN_6M; break;
case DESC90_RATE9M: ret_rate = MGN_9M; break;
case DESC90_RATE12M: ret_rate = MGN_12M; break;
case DESC90_RATE18M: ret_rate = MGN_18M; break;
case DESC90_RATE24M: ret_rate = MGN_24M; break;
case DESC90_RATE36M: ret_rate = MGN_36M; break;
case DESC90_RATE48M: ret_rate = MGN_48M; break;
case DESC90_RATE54M: ret_rate = MGN_54M; break;
default:
ret_rate = 0xff;
RT_TRACE(COMP_RECV, "HwRateToMRate90(): Non supported Rate [%x], bIsHT = %d!!!\n", rate, bIsHT);
break;
}
} else {
switch(rate) {
case DESC90_RATEMCS0: ret_rate = MGN_MCS0; break;
case DESC90_RATEMCS1: ret_rate = MGN_MCS1; break;
case DESC90_RATEMCS2: ret_rate = MGN_MCS2; break;
case DESC90_RATEMCS3: ret_rate = MGN_MCS3; break;
case DESC90_RATEMCS4: ret_rate = MGN_MCS4; break;
case DESC90_RATEMCS5: ret_rate = MGN_MCS5; break;
case DESC90_RATEMCS6: ret_rate = MGN_MCS6; break;
case DESC90_RATEMCS7: ret_rate = MGN_MCS7; break;
case DESC90_RATEMCS8: ret_rate = MGN_MCS8; break;
case DESC90_RATEMCS9: ret_rate = MGN_MCS9; break;
case DESC90_RATEMCS10: ret_rate = MGN_MCS10; break;
case DESC90_RATEMCS11: ret_rate = MGN_MCS11; break;
case DESC90_RATEMCS12: ret_rate = MGN_MCS12; break;
case DESC90_RATEMCS13: ret_rate = MGN_MCS13; break;
case DESC90_RATEMCS14: ret_rate = MGN_MCS14; break;
case DESC90_RATEMCS15: ret_rate = MGN_MCS15; break;
case DESC90_RATEMCS32: ret_rate = (0x80|0x20); break;
default:
ret_rate = 0xff;
RT_TRACE(COMP_RECV, "HwRateToMRate90(): Non supported Rate [%x], bIsHT = %d!!!\n",rate, bIsHT);
break;
}
}
return ret_rate;
}
/**
* Function: UpdateRxPktTimeStamp
* Overview: Recored down the TSF time stamp when receiving a packet
*
* Input:
* PADAPTER Adapter
* PRT_RFD pRfd,
*
* Output:
* PRT_RFD pRfd
* (pRfd->Status.TimeStampHigh is updated)
* (pRfd->Status.TimeStampLow is updated)
* Return:
* None
*/
void UpdateRxPktTimeStamp8190 (struct net_device *dev, struct ieee80211_rx_stats *stats)
{
struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
if(stats->bIsAMPDU && !stats->bFirstMPDU) {
stats->mac_time[0] = priv->LastRxDescTSFLow;
stats->mac_time[1] = priv->LastRxDescTSFHigh;
} else {
priv->LastRxDescTSFLow = stats->mac_time[0];
priv->LastRxDescTSFHigh = stats->mac_time[1];
}
}
//by amy 080606
long rtl819x_translate_todbm(u8 signal_strength_index )// 0-100 index.
{
long signal_power; // in dBm.
// Translate to dBm (x=0.5y-95).
signal_power = (long)((signal_strength_index + 1) >> 1);
signal_power -= 95;
return signal_power;
}
/* 2008/01/22 MH We can not delcare RSSI/EVM total value of sliding window to
be a local static. Otherwise, it may increase when we return from S3/S4. The
value will be kept in memory or disk. We must delcare the value in adapter
and it will be reinitialized when return from S3/S4. */
void rtl8192_process_phyinfo(struct r8192_priv * priv,u8* buffer, struct ieee80211_rx_stats * pprevious_stats, struct ieee80211_rx_stats * pcurrent_stats)
{
bool bcheck = false;
u8 rfpath;
u32 nspatial_stream, tmp_val;
//u8 i;
static u32 slide_rssi_index=0, slide_rssi_statistics=0;
static u32 slide_evm_index=0, slide_evm_statistics=0;
static u32 last_rssi=0, last_evm=0;
static u32 slide_beacon_adc_pwdb_index=0, slide_beacon_adc_pwdb_statistics=0;
static u32 last_beacon_adc_pwdb=0;
struct ieee80211_hdr_3addr *hdr;
u16 sc ;
unsigned int frag,seq;
hdr = (struct ieee80211_hdr_3addr *)buffer;
sc = le16_to_cpu(hdr->seq_ctl);
frag = WLAN_GET_SEQ_FRAG(sc);
seq = WLAN_GET_SEQ_SEQ(sc);
//cosa add 04292008 to record the sequence number
pcurrent_stats->Seq_Num = seq;
//
// Check whether we should take the previous packet into accounting
//
if(!pprevious_stats->bIsAMPDU)
{
// if previous packet is not aggregated packet
bcheck = true;
}else
{
}
if(slide_rssi_statistics++ >= PHY_RSSI_SLID_WIN_MAX)
{
slide_rssi_statistics = PHY_RSSI_SLID_WIN_MAX;
last_rssi = priv->stats.slide_signal_strength[slide_rssi_index];
priv->stats.slide_rssi_total -= last_rssi;
}
priv->stats.slide_rssi_total += pprevious_stats->SignalStrength;
priv->stats.slide_signal_strength[slide_rssi_index++] = pprevious_stats->SignalStrength;
if(slide_rssi_index >= PHY_RSSI_SLID_WIN_MAX)
slide_rssi_index = 0;
// <1> Showed on UI for user, in dbm
tmp_val = priv->stats.slide_rssi_total/slide_rssi_statistics;
priv->stats.signal_strength = rtl819x_translate_todbm((u8)tmp_val);
pcurrent_stats->rssi = priv->stats.signal_strength;
//
// If the previous packet does not match the criteria, neglect it
//
if(!pprevious_stats->bPacketMatchBSSID)
{
if(!pprevious_stats->bToSelfBA)
return;
}
if(!bcheck)
return;
//rtl8190_process_cck_rxpathsel(priv,pprevious_stats);//only rtl8190 supported
//
// Check RSSI
//
priv->stats.num_process_phyinfo++;
/* record the general signal strength to the sliding window. */
// <2> Showed on UI for engineering
// hardware does not provide rssi information for each rf path in CCK
if(!pprevious_stats->bIsCCK && (pprevious_stats->bPacketToSelf || pprevious_stats->bToSelfBA))
{
for (rfpath = RF90_PATH_A; rfpath < priv->NumTotalRFPath; rfpath++)
{
if (!rtl8192_phy_CheckIsLegalRFPath(priv->ieee80211->dev, rfpath))
continue;
//Fixed by Jacken 2008-03-20
if(priv->stats.rx_rssi_percentage[rfpath] == 0)
{
priv->stats.rx_rssi_percentage[rfpath] = pprevious_stats->RxMIMOSignalStrength[rfpath];
//DbgPrint("MIMO RSSI initialize \n");
}
if(pprevious_stats->RxMIMOSignalStrength[rfpath] > priv->stats.rx_rssi_percentage[rfpath])
{
priv->stats.rx_rssi_percentage[rfpath] =
( (priv->stats.rx_rssi_percentage[rfpath]*(Rx_Smooth_Factor-1)) +
(pprevious_stats->RxMIMOSignalStrength[rfpath])) /(Rx_Smooth_Factor);
priv->stats.rx_rssi_percentage[rfpath] = priv->stats.rx_rssi_percentage[rfpath] + 1;
}
else
{
priv->stats.rx_rssi_percentage[rfpath] =
( (priv->stats.rx_rssi_percentage[rfpath]*(Rx_Smooth_Factor-1)) +
(pprevious_stats->RxMIMOSignalStrength[rfpath])) /(Rx_Smooth_Factor);
}
RT_TRACE(COMP_DBG,"priv->stats.rx_rssi_percentage[rfPath] = %d \n" ,priv->stats.rx_rssi_percentage[rfpath] );
}
}
//
// Check PWDB.
//
RT_TRACE(COMP_RXDESC, "Smooth %s PWDB = %d\n",
pprevious_stats->bIsCCK? "CCK": "OFDM",
pprevious_stats->RxPWDBAll);
if(pprevious_stats->bPacketBeacon)
{
/* record the beacon pwdb to the sliding window. */
if(slide_beacon_adc_pwdb_statistics++ >= PHY_Beacon_RSSI_SLID_WIN_MAX)
{
slide_beacon_adc_pwdb_statistics = PHY_Beacon_RSSI_SLID_WIN_MAX;
last_beacon_adc_pwdb = priv->stats.Slide_Beacon_pwdb[slide_beacon_adc_pwdb_index];
priv->stats.Slide_Beacon_Total -= last_beacon_adc_pwdb;
//DbgPrint("slide_beacon_adc_pwdb_index = %d, last_beacon_adc_pwdb = %d, Adapter->RxStats.Slide_Beacon_Total = %d\n",
// slide_beacon_adc_pwdb_index, last_beacon_adc_pwdb, Adapter->RxStats.Slide_Beacon_Total);
}
priv->stats.Slide_Beacon_Total += pprevious_stats->RxPWDBAll;
priv->stats.Slide_Beacon_pwdb[slide_beacon_adc_pwdb_index] = pprevious_stats->RxPWDBAll;
//DbgPrint("slide_beacon_adc_pwdb_index = %d, pPreviousRfd->Status.RxPWDBAll = %d\n", slide_beacon_adc_pwdb_index, pPreviousRfd->Status.RxPWDBAll);
slide_beacon_adc_pwdb_index++;
if(slide_beacon_adc_pwdb_index >= PHY_Beacon_RSSI_SLID_WIN_MAX)
slide_beacon_adc_pwdb_index = 0;
pprevious_stats->RxPWDBAll = priv->stats.Slide_Beacon_Total/slide_beacon_adc_pwdb_statistics;
if(pprevious_stats->RxPWDBAll >= 3)
pprevious_stats->RxPWDBAll -= 3;
}
RT_TRACE(COMP_RXDESC, "Smooth %s PWDB = %d\n",
pprevious_stats->bIsCCK? "CCK": "OFDM",
pprevious_stats->RxPWDBAll);
if(pprevious_stats->bPacketToSelf || pprevious_stats->bPacketBeacon || pprevious_stats->bToSelfBA)
{
if(priv->undecorated_smoothed_pwdb < 0) // initialize
{
priv->undecorated_smoothed_pwdb = pprevious_stats->RxPWDBAll;
//DbgPrint("First pwdb initialize \n");
}
if(pprevious_stats->RxPWDBAll > (u32)priv->undecorated_smoothed_pwdb)
{
priv->undecorated_smoothed_pwdb =
( ((priv->undecorated_smoothed_pwdb)*(Rx_Smooth_Factor-1)) +
(pprevious_stats->RxPWDBAll)) /(Rx_Smooth_Factor);
priv->undecorated_smoothed_pwdb = priv->undecorated_smoothed_pwdb + 1;
}
else
{
priv->undecorated_smoothed_pwdb =
( ((priv->undecorated_smoothed_pwdb)*(Rx_Smooth_Factor-1)) +
(pprevious_stats->RxPWDBAll)) /(Rx_Smooth_Factor);
}
}
//
// Check EVM
//
/* record the general EVM to the sliding window. */
if(pprevious_stats->SignalQuality == 0)
{
}
else
{
if(pprevious_stats->bPacketToSelf || pprevious_stats->bPacketBeacon || pprevious_stats->bToSelfBA){
if(slide_evm_statistics++ >= PHY_RSSI_SLID_WIN_MAX){
slide_evm_statistics = PHY_RSSI_SLID_WIN_MAX;
last_evm = priv->stats.slide_evm[slide_evm_index];
priv->stats.slide_evm_total -= last_evm;
}
priv->stats.slide_evm_total += pprevious_stats->SignalQuality;
priv->stats.slide_evm[slide_evm_index++] = pprevious_stats->SignalQuality;
if(slide_evm_index >= PHY_RSSI_SLID_WIN_MAX)
slide_evm_index = 0;
// <1> Showed on UI for user, in percentage.
tmp_val = priv->stats.slide_evm_total/slide_evm_statistics;
priv->stats.signal_quality = tmp_val;
//cosa add 10/11/2007, Showed on UI for user in Windows Vista, for Link quality.
priv->stats.last_signal_strength_inpercent = tmp_val;
}
// <2> Showed on UI for engineering
if(pprevious_stats->bPacketToSelf || pprevious_stats->bPacketBeacon || pprevious_stats->bToSelfBA)
{
for(nspatial_stream = 0; nspatial_stream<2 ; nspatial_stream++) // 2 spatial stream
{
if(pprevious_stats->RxMIMOSignalQuality[nspatial_stream] != -1)
{
if(priv->stats.rx_evm_percentage[nspatial_stream] == 0) // initialize
{
priv->stats.rx_evm_percentage[nspatial_stream] = pprevious_stats->RxMIMOSignalQuality[nspatial_stream];
}
priv->stats.rx_evm_percentage[nspatial_stream] =
( (priv->stats.rx_evm_percentage[nspatial_stream]* (Rx_Smooth_Factor-1)) +
(pprevious_stats->RxMIMOSignalQuality[nspatial_stream]* 1)) / (Rx_Smooth_Factor);
}
}
}
}
}
/*-----------------------------------------------------------------------------
* Function: rtl819x_query_rxpwrpercentage()
*
* Overview:
*
* Input: char antpower
*
* Output: NONE
*
* Return: 0-100 percentage
*
* Revised History:
* When Who Remark
* 05/26/2008 amy Create Version 0 porting from windows code.
*
*---------------------------------------------------------------------------*/
static u8 rtl819x_query_rxpwrpercentage(
char antpower
)
{
if ((antpower <= -100) || (antpower >= 20))
{
return 0;
}
else if (antpower >= 0)
{
return 100;
}
else
{
return (100+antpower);
}
} /* QueryRxPwrPercentage */
static u8
rtl819x_evm_dbtopercentage(
char value
)
{
char ret_val;
ret_val = value;
if(ret_val >= 0)
ret_val = 0;
if(ret_val <= -33)
ret_val = -33;
ret_val = 0 - ret_val;
ret_val*=3;
if(ret_val == 99)
ret_val = 100;
return(ret_val);
}
//
// Description:
// We want good-looking for signal strength/quality
// 2007/7/19 01:09, by cosa.
//
long
rtl819x_signal_scale_mapping(
long currsig
)
{
long retsig;
// Step 1. Scale mapping.
if(currsig >= 61 && currsig <= 100)
{
retsig = 90 + ((currsig - 60) / 4);
}
else if(currsig >= 41 && currsig <= 60)
{
retsig = 78 + ((currsig - 40) / 2);
}
else if(currsig >= 31 && currsig <= 40)
{
retsig = 66 + (currsig - 30);
}
else if(currsig >= 21 && currsig <= 30)
{
retsig = 54 + (currsig - 20);
}
else if(currsig >= 5 && currsig <= 20)
{
retsig = 42 + (((currsig - 5) * 2) / 3);
}
else if(currsig == 4)
{
retsig = 36;
}
else if(currsig == 3)
{
retsig = 27;
}
else if(currsig == 2)
{
retsig = 18;
}
else if(currsig == 1)
{
retsig = 9;
}
else
{
retsig = currsig;
}
return retsig;
}
static void rtl8192_query_rxphystatus(
struct r8192_priv * priv,
struct ieee80211_rx_stats * pstats,
rx_drvinfo_819x_usb * pdrvinfo,
struct ieee80211_rx_stats * precord_stats,
bool bpacket_match_bssid,
bool bpacket_toself,
bool bPacketBeacon,
bool bToSelfBA
)
{
//PRT_RFD_STATUS pRtRfdStatus = &(pRfd->Status);
phy_sts_ofdm_819xusb_t* pofdm_buf;
phy_sts_cck_819xusb_t * pcck_buf;
phy_ofdm_rx_status_rxsc_sgien_exintfflag* prxsc;
u8 *prxpkt;
u8 i, max_spatial_stream, tmp_rxsnr, tmp_rxevm, rxsc_sgien_exflg;
char rx_pwr[4], rx_pwr_all=0;
//long rx_avg_pwr = 0;
char rx_snrX, rx_evmX;
u8 evm, pwdb_all;
u32 RSSI, total_rssi=0;//, total_evm=0;
// long signal_strength_index = 0;
u8 is_cck_rate=0;
u8 rf_rx_num = 0;
priv->stats.numqry_phystatus++;
is_cck_rate = rx_hal_is_cck_rate(pdrvinfo);
// Record it for next packet processing
memset(precord_stats, 0, sizeof(struct ieee80211_rx_stats));
pstats->bPacketMatchBSSID = precord_stats->bPacketMatchBSSID = bpacket_match_bssid;
pstats->bPacketToSelf = precord_stats->bPacketToSelf = bpacket_toself;
pstats->bIsCCK = precord_stats->bIsCCK = is_cck_rate;//RX_HAL_IS_CCK_RATE(pDrvInfo);
pstats->bPacketBeacon = precord_stats->bPacketBeacon = bPacketBeacon;
pstats->bToSelfBA = precord_stats->bToSelfBA = bToSelfBA;
prxpkt = (u8*)pdrvinfo;
/* Move pointer to the 16th bytes. Phy status start address. */
prxpkt += sizeof(rx_drvinfo_819x_usb);
/* Initial the cck and ofdm buffer pointer */
pcck_buf = (phy_sts_cck_819xusb_t *)prxpkt;
pofdm_buf = (phy_sts_ofdm_819xusb_t *)prxpkt;
pstats->RxMIMOSignalQuality[0] = -1;
pstats->RxMIMOSignalQuality[1] = -1;
precord_stats->RxMIMOSignalQuality[0] = -1;
precord_stats->RxMIMOSignalQuality[1] = -1;
if(is_cck_rate)
{
//
// (1)Hardware does not provide RSSI for CCK
//
//
// (2)PWDB, Average PWDB cacluated by hardware (for rate adaptive)
//
u8 report;//, cck_agc_rpt;
priv->stats.numqry_phystatusCCK++;
if(!priv->bCckHighPower)
{
report = pcck_buf->cck_agc_rpt & 0xc0;
report = report>>6;
switch(report)
{
//Fixed by Jacken from Bryant 2008-03-20
//Original value is -38 , -26 , -14 , -2
//Fixed value is -35 , -23 , -11 , 6
case 0x3:
rx_pwr_all = -35 - (pcck_buf->cck_agc_rpt & 0x3e);
break;
case 0x2:
rx_pwr_all = -23 - (pcck_buf->cck_agc_rpt & 0x3e);
break;
case 0x1:
rx_pwr_all = -11 - (pcck_buf->cck_agc_rpt & 0x3e);
break;
case 0x0:
rx_pwr_all = 6 - (pcck_buf->cck_agc_rpt & 0x3e);
break;
}
}
else
{
report = pcck_buf->cck_agc_rpt & 0x60;
report = report>>5;
switch(report)
{
case 0x3:
rx_pwr_all = -35 - ((pcck_buf->cck_agc_rpt & 0x1f)<<1) ;
break;
case 0x2:
rx_pwr_all = -23 - ((pcck_buf->cck_agc_rpt & 0x1f)<<1);
break;
case 0x1:
rx_pwr_all = -11 - ((pcck_buf->cck_agc_rpt & 0x1f)<<1) ;
break;
case 0x0:
rx_pwr_all = 6 - ((pcck_buf->cck_agc_rpt & 0x1f)<<1) ;
break;
}
}
pwdb_all = rtl819x_query_rxpwrpercentage(rx_pwr_all);
pstats->RxPWDBAll = precord_stats->RxPWDBAll = pwdb_all;
pstats->RecvSignalPower = pwdb_all;
//
// (3) Get Signal Quality (EVM)
//
//if(bpacket_match_bssid)
{
u8 sq;
if(pstats->RxPWDBAll > 40)
{
sq = 100;
}else
{
sq = pcck_buf->sq_rpt;
if(pcck_buf->sq_rpt > 64)
sq = 0;
else if (pcck_buf->sq_rpt < 20)
sq = 100;
else
sq = ((64-sq) * 100) / 44;
}
pstats->SignalQuality = precord_stats->SignalQuality = sq;
pstats->RxMIMOSignalQuality[0] = precord_stats->RxMIMOSignalQuality[0] = sq;
pstats->RxMIMOSignalQuality[1] = precord_stats->RxMIMOSignalQuality[1] = -1;
}
}
else
{
priv->stats.numqry_phystatusHT++;
//
// (1)Get RSSI for HT rate
//
for(i=RF90_PATH_A; i<priv->NumTotalRFPath; i++)
{
// 2008/01/30 MH we will judge RF RX path now.
if (priv->brfpath_rxenable[i])
rf_rx_num++;
else
continue;
if (!rtl8192_phy_CheckIsLegalRFPath(priv->ieee80211->dev, i))
continue;
//Fixed by Jacken from Bryant 2008-03-20
//Original value is 106
rx_pwr[i] = ((pofdm_buf->trsw_gain_X[i]&0x3F)*2) - 106;
//Get Rx snr value in DB
tmp_rxsnr = pofdm_buf->rxsnr_X[i];
rx_snrX = (char)(tmp_rxsnr);
//rx_snrX >>= 1;
rx_snrX /= 2;
priv->stats.rxSNRdB[i] = (long)rx_snrX;
/* Translate DBM to percentage. */
RSSI = rtl819x_query_rxpwrpercentage(rx_pwr[i]);
total_rssi += RSSI;
/* Record Signal Strength for next packet */
//if(bpacket_match_bssid)
{
pstats->RxMIMOSignalStrength[i] =(u8) RSSI;
precord_stats->RxMIMOSignalStrength[i] =(u8) RSSI;
}
}
//
// (2)PWDB, Average PWDB cacluated by hardware (for rate adaptive)
//
//Fixed by Jacken from Bryant 2008-03-20
//Original value is 106
rx_pwr_all = (((pofdm_buf->pwdb_all ) >> 1 )& 0x7f) -106;
pwdb_all = rtl819x_query_rxpwrpercentage(rx_pwr_all);
pstats->RxPWDBAll = precord_stats->RxPWDBAll = pwdb_all;
pstats->RxPower = precord_stats->RxPower = rx_pwr_all;
//
// (3)EVM of HT rate
//
if(pdrvinfo->RxHT && pdrvinfo->RxRate>=DESC90_RATEMCS8 &&
pdrvinfo->RxRate<=DESC90_RATEMCS15)
max_spatial_stream = 2; //both spatial stream make sense
else
max_spatial_stream = 1; //only spatial stream 1 makes sense
for(i=0; i<max_spatial_stream; i++)
{
tmp_rxevm = pofdm_buf->rxevm_X[i];
rx_evmX = (char)(tmp_rxevm);
// Do not use shift operation like "rx_evmX >>= 1" because the compilor of free build environment
// fill most significant bit to "zero" when doing shifting operation which may change a negative
// value to positive one, then the dbm value (which is supposed to be negative) is not correct anymore.
rx_evmX /= 2; //dbm
evm = rtl819x_evm_dbtopercentage(rx_evmX);
//if(bpacket_match_bssid)
{
if(i==0) // Fill value in RFD, Get the first spatial stream only
pstats->SignalQuality = precord_stats->SignalQuality = (u8)(evm & 0xff);
pstats->RxMIMOSignalQuality[i] = precord_stats->RxMIMOSignalQuality[i] = (u8)(evm & 0xff);
}
}
/* record rx statistics for debug */
rxsc_sgien_exflg = pofdm_buf->rxsc_sgien_exflg;
prxsc = (phy_ofdm_rx_status_rxsc_sgien_exintfflag *)&rxsc_sgien_exflg;
if(pdrvinfo->BW) //40M channel
priv->stats.received_bwtype[1+prxsc->rxsc]++;
else //20M channel
priv->stats.received_bwtype[0]++;
}
//UI BSS List signal strength(in percentage), make it good looking, from 0~100.
//It is assigned to the BSS List in GetValueFromBeaconOrProbeRsp().
if(is_cck_rate)
{
pstats->SignalStrength = precord_stats->SignalStrength = (u8)(rtl819x_signal_scale_mapping((long)pwdb_all));//PWDB_ALL;
}
else
{
//pRfd->Status.SignalStrength = pRecordRfd->Status.SignalStrength = (u8)(SignalScaleMapping(total_rssi/=RF90_PATH_MAX));//(u8)(total_rssi/=RF90_PATH_MAX);
// We can judge RX path number now.
if (rf_rx_num != 0)
pstats->SignalStrength = precord_stats->SignalStrength = (u8)(rtl819x_signal_scale_mapping((long)(total_rssi/=rf_rx_num)));
}
} /* QueryRxPhyStatus8190Pci */
void
rtl8192_record_rxdesc_forlateruse(
struct ieee80211_rx_stats * psrc_stats,
struct ieee80211_rx_stats * ptarget_stats
)
{
ptarget_stats->bIsAMPDU = psrc_stats->bIsAMPDU;
ptarget_stats->bFirstMPDU = psrc_stats->bFirstMPDU;
ptarget_stats->Seq_Num = psrc_stats->Seq_Num;
}
void TranslateRxSignalStuff819xUsb(struct sk_buff *skb,
struct ieee80211_rx_stats * pstats,
rx_drvinfo_819x_usb *pdrvinfo)
{
// TODO: We must only check packet for current MAC address. Not finish
rtl8192_rx_info *info = (struct rtl8192_rx_info *)skb->cb;
struct net_device *dev=info->dev;
struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
bool bpacket_match_bssid, bpacket_toself;
bool bPacketBeacon=FALSE, bToSelfBA=FALSE;
static struct ieee80211_rx_stats previous_stats;
struct ieee80211_hdr_3addr *hdr;//by amy
u16 fc,type;
// Get Signal Quality for only RX data queue (but not command queue)
u8* tmp_buf;
//u16 tmp_buf_len = 0;
u8 *praddr;
/* Get MAC frame start address. */
tmp_buf = (u8*)skb->data;// + get_rxpacket_shiftbytes_819xusb(pstats);
hdr = (struct ieee80211_hdr_3addr *)tmp_buf;
fc = le16_to_cpu(hdr->frame_ctl);
type = WLAN_FC_GET_TYPE(fc);
praddr = hdr->addr1;
/* Check if the received packet is acceptabe. */
bpacket_match_bssid = ((IEEE80211_FTYPE_CTL != type) &&
(eqMacAddr(priv->ieee80211->current_network.bssid, (fc & IEEE80211_FCTL_TODS)? hdr->addr1 : (fc & IEEE80211_FCTL_FROMDS )? hdr->addr2 : hdr->addr3))
&& (!pstats->bHwError) && (!pstats->bCRC)&& (!pstats->bICV));
bpacket_toself = bpacket_match_bssid & (eqMacAddr(praddr, priv->ieee80211->dev->dev_addr));
if(WLAN_FC_GET_FRAMETYPE(fc)== IEEE80211_STYPE_BEACON)
{
bPacketBeacon = true;
//DbgPrint("Beacon 2, MatchBSSID = %d, ToSelf = %d \n", bPacketMatchBSSID, bPacketToSelf);
}
if(WLAN_FC_GET_FRAMETYPE(fc) == IEEE80211_STYPE_BLOCKACK)
{
if((eqMacAddr(praddr,dev->dev_addr)))
bToSelfBA = true;
//DbgPrint("BlockAck, MatchBSSID = %d, ToSelf = %d \n", bPacketMatchBSSID, bPacketToSelf);
}
if(bpacket_match_bssid)
{
priv->stats.numpacket_matchbssid++;
}
if(bpacket_toself){
priv->stats.numpacket_toself++;
}
//
// Process PHY information for previous packet (RSSI/PWDB/EVM)
//
// Because phy information is contained in the last packet of AMPDU only, so driver
// should process phy information of previous packet
rtl8192_process_phyinfo(priv, tmp_buf, &previous_stats, pstats);
rtl8192_query_rxphystatus(priv, pstats, pdrvinfo, &previous_stats, bpacket_match_bssid,bpacket_toself,bPacketBeacon,bToSelfBA);
rtl8192_record_rxdesc_forlateruse(pstats, &previous_stats);
}
/**
* Function: UpdateReceivedRateHistogramStatistics
* Overview: Recored down the received data rate
*
* Input:
* struct net_device *dev
* struct ieee80211_rx_stats *stats
*
* Output:
*
* (priv->stats.ReceivedRateHistogram[] is updated)
* Return:
* None
*/
void
UpdateReceivedRateHistogramStatistics8190(
struct net_device *dev,
struct ieee80211_rx_stats *stats
)
{
struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
u32 rcvType=1; //0: Total, 1:OK, 2:CRC, 3:ICV
u32 rateIndex;
u32 preamble_guardinterval; //1: short preamble/GI, 0: long preamble/GI
if(stats->bCRC)
rcvType = 2;
else if(stats->bICV)
rcvType = 3;
if(stats->bShortPreamble)
preamble_guardinterval = 1;// short
else
preamble_guardinterval = 0;// long
switch(stats->rate)
{
//
// CCK rate
//
case MGN_1M: rateIndex = 0; break;
case MGN_2M: rateIndex = 1; break;
case MGN_5_5M: rateIndex = 2; break;
case MGN_11M: rateIndex = 3; break;
//
// Legacy OFDM rate
//
case MGN_6M: rateIndex = 4; break;
case MGN_9M: rateIndex = 5; break;
case MGN_12M: rateIndex = 6; break;
case MGN_18M: rateIndex = 7; break;
case MGN_24M: rateIndex = 8; break;
case MGN_36M: rateIndex = 9; break;
case MGN_48M: rateIndex = 10; break;
case MGN_54M: rateIndex = 11; break;
//
// 11n High throughput rate
//
case MGN_MCS0: rateIndex = 12; break;
case MGN_MCS1: rateIndex = 13; break;
case MGN_MCS2: rateIndex = 14; break;
case MGN_MCS3: rateIndex = 15; break;
case MGN_MCS4: rateIndex = 16; break;
case MGN_MCS5: rateIndex = 17; break;
case MGN_MCS6: rateIndex = 18; break;
case MGN_MCS7: rateIndex = 19; break;
case MGN_MCS8: rateIndex = 20; break;
case MGN_MCS9: rateIndex = 21; break;
case MGN_MCS10: rateIndex = 22; break;
case MGN_MCS11: rateIndex = 23; break;
case MGN_MCS12: rateIndex = 24; break;
case MGN_MCS13: rateIndex = 25; break;
case MGN_MCS14: rateIndex = 26; break;
case MGN_MCS15: rateIndex = 27; break;
default: rateIndex = 28; break;
}
priv->stats.received_preamble_GI[preamble_guardinterval][rateIndex]++;
priv->stats.received_rate_histogram[0][rateIndex]++; //total
priv->stats.received_rate_histogram[rcvType][rateIndex]++;
}
void query_rxdesc_status(struct sk_buff *skb, struct ieee80211_rx_stats *stats, bool bIsRxAggrSubframe)
{
rtl8192_rx_info *info = (struct rtl8192_rx_info *)skb->cb;
struct net_device *dev=info->dev;
struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
//rx_desc_819x_usb *desc = (rx_desc_819x_usb *)skb->data;
rx_drvinfo_819x_usb *driver_info = NULL;
//
//Get Rx Descriptor Information
//
#ifdef USB_RX_AGGREGATION_SUPPORT
if (bIsRxAggrSubframe)
{
rx_desc_819x_usb_aggr_subframe *desc = (rx_desc_819x_usb_aggr_subframe *)skb->data;
stats->Length = desc->Length ;
stats->RxDrvInfoSize = desc->RxDrvInfoSize;
stats->RxBufShift = 0; //RxBufShift = 2 in RxDesc, but usb didn't shift bytes in fact.
stats->bICV = desc->ICV;
stats->bCRC = desc->CRC32;
stats->bHwError = stats->bCRC|stats->bICV;
stats->Decrypted = !desc->SWDec;//RTL8190 set this bit to indicate that Hw does not decrypt packet
} else
#endif
{
rx_desc_819x_usb *desc = (rx_desc_819x_usb *)skb->data;
stats->Length = desc->Length;
stats->RxDrvInfoSize = desc->RxDrvInfoSize;
stats->RxBufShift = 0;//desc->Shift&0x03;
stats->bICV = desc->ICV;
stats->bCRC = desc->CRC32;
stats->bHwError = stats->bCRC|stats->bICV;
//RTL8190 set this bit to indicate that Hw does not decrypt packet
stats->Decrypted = !desc->SWDec;
}
if((priv->ieee80211->pHTInfo->bCurrentHTSupport == true) && (priv->ieee80211->pairwise_key_type == KEY_TYPE_CCMP))
{
stats->bHwError = false;
}
else
{
stats->bHwError = stats->bCRC|stats->bICV;
}
if(stats->Length < 24 || stats->Length > MAX_8192U_RX_SIZE)
stats->bHwError |= 1;
//
//Get Driver Info
//
// TODO: Need to verify it on FGPA platform
//Driver info are written to the RxBuffer following rx desc
if (stats->RxDrvInfoSize != 0) {
driver_info = (rx_drvinfo_819x_usb *)(skb->data + sizeof(rx_desc_819x_usb) + \
stats->RxBufShift);
/* unit: 0.5M */
/* TODO */
if(!stats->bHwError){
u8 ret_rate;
ret_rate = HwRateToMRate90(driver_info->RxHT, driver_info->RxRate);
if(ret_rate == 0xff)
{
// Abnormal Case: Receive CRC OK packet with Rx descriptor indicating non supported rate.
// Special Error Handling here, 2008.05.16, by Emily
stats->bHwError = 1;
stats->rate = MGN_1M; //Set 1M rate by default
}else
{
stats->rate = ret_rate;
}
}
else
stats->rate = 0x02;
stats->bShortPreamble = driver_info->SPLCP;
UpdateReceivedRateHistogramStatistics8190(dev, stats);
stats->bIsAMPDU = (driver_info->PartAggr==1);
stats->bFirstMPDU = (driver_info->PartAggr==1) && (driver_info->FirstAGGR==1);
stats->TimeStampLow = driver_info->TSFL;
// xiong mask it, 070514
//pRfd->Status.TimeStampHigh = PlatformEFIORead4Byte(Adapter, TSFR+4);
// stats->TimeStampHigh = read_nic_dword(dev, TSFR+4);
UpdateRxPktTimeStamp8190(dev, stats);
//
// Rx A-MPDU
//
if(driver_info->FirstAGGR==1 || driver_info->PartAggr == 1)
RT_TRACE(COMP_RXDESC, "driver_info->FirstAGGR = %d, driver_info->PartAggr = %d\n",
driver_info->FirstAGGR, driver_info->PartAggr);
}
skb_pull(skb,sizeof(rx_desc_819x_usb));
//
// Get Total offset of MPDU Frame Body
//
if((stats->RxBufShift + stats->RxDrvInfoSize) > 0) {
stats->bShift = 1;
skb_pull(skb,stats->RxBufShift + stats->RxDrvInfoSize);
}
#ifdef USB_RX_AGGREGATION_SUPPORT
/* for the rx aggregated sub frame, the redundant space truelly contained in the packet */
if(bIsRxAggrSubframe) {
skb_pull(skb, 8);
}
#endif
/* for debug 2008.5.29 */
//added by vivi, for MP, 20080108
stats->RxIs40MHzPacket = driver_info->BW;
if(stats->RxDrvInfoSize != 0)
TranslateRxSignalStuff819xUsb(skb, stats, driver_info);
}
u32 GetRxPacketShiftBytes819xUsb(struct ieee80211_rx_stats *Status, bool bIsRxAggrSubframe)
{
#ifdef USB_RX_AGGREGATION_SUPPORT
if (bIsRxAggrSubframe)
return (sizeof(rx_desc_819x_usb) + Status->RxDrvInfoSize
+ Status->RxBufShift + 8);
else
#endif
return (sizeof(rx_desc_819x_usb) + Status->RxDrvInfoSize
+ Status->RxBufShift);
}
void rtl8192_rx_nomal(struct sk_buff* skb)
{
rtl8192_rx_info *info = (struct rtl8192_rx_info *)skb->cb;
struct net_device *dev=info->dev;
struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
struct ieee80211_rx_stats stats = {
.signal = 0,
.noise = -98,
.rate = 0,
// .mac_time = jiffies,
.freq = IEEE80211_24GHZ_BAND,
};
u32 rx_pkt_len = 0;
struct ieee80211_hdr_1addr *ieee80211_hdr = NULL;
bool unicast_packet = false;
#ifdef USB_RX_AGGREGATION_SUPPORT
struct sk_buff *agg_skb = NULL;
u32 TotalLength = 0;
u32 TempDWord = 0;
u32 PacketLength = 0;
u32 PacketOccupiedLendth = 0;
u8 TempByte = 0;
u32 PacketShiftBytes = 0;
rx_desc_819x_usb_aggr_subframe *RxDescr = NULL;
u8 PaddingBytes = 0;
//add just for testing
u8 testing;
#endif
/* 20 is for ps-poll */
if((skb->len >=(20 + sizeof(rx_desc_819x_usb))) && (skb->len < RX_URB_SIZE)) {
#ifdef USB_RX_AGGREGATION_SUPPORT
TempByte = *(skb->data + sizeof(rx_desc_819x_usb));
#endif
/* first packet should not contain Rx aggregation header */
query_rxdesc_status(skb, &stats, false);
/* TODO */
/* hardware related info */
#ifdef USB_RX_AGGREGATION_SUPPORT
if (TempByte & BIT0) {
agg_skb = skb;
//TotalLength = agg_skb->len - 4; /*sCrcLng*/
TotalLength = stats.Length - 4; /*sCrcLng*/
//RT_TRACE(COMP_RECV, "%s:first aggregated packet!Length=%d\n",__FUNCTION__,TotalLength);
/* though the head pointer has passed this position */
TempDWord = *(u32 *)(agg_skb->data - 4);
PacketLength = (u16)(TempDWord & 0x3FFF); /*sCrcLng*/
skb = dev_alloc_skb(PacketLength);
memcpy(skb_put(skb,PacketLength),agg_skb->data,PacketLength);
PacketShiftBytes = GetRxPacketShiftBytes819xUsb(&stats, false);
}
#endif
/* Process the MPDU recevied */
skb_trim(skb, skb->len - 4/*sCrcLng*/);
rx_pkt_len = skb->len;
ieee80211_hdr = (struct ieee80211_hdr_1addr *)skb->data;
unicast_packet = false;
if(is_broadcast_ether_addr(ieee80211_hdr->addr1)) {
//TODO
}else if(is_multicast_ether_addr(ieee80211_hdr->addr1)){
//TODO
}else {
/* unicast packet */
unicast_packet = true;
}
if(!ieee80211_rx(priv->ieee80211,skb, &stats)) {
dev_kfree_skb_any(skb);
} else {
priv->stats.rxoktotal++;
if(unicast_packet) {
priv->stats.rxbytesunicast += rx_pkt_len;
}
}
#ifdef USB_RX_AGGREGATION_SUPPORT
testing = 1;
// (PipeIndex == 0) && (TempByte & BIT0) => TotalLength > 0.
if (TotalLength > 0) {
PacketOccupiedLendth = PacketLength + (PacketShiftBytes + 8);
if ((PacketOccupiedLendth & 0xFF) != 0)
PacketOccupiedLendth = (PacketOccupiedLendth & 0xFFFFFF00) + 256;
PacketOccupiedLendth -= 8;
TempDWord = PacketOccupiedLendth - PacketShiftBytes; /*- PacketLength */
if (agg_skb->len > TempDWord)
skb_pull(agg_skb, TempDWord);
else
agg_skb->len = 0;
while (agg_skb->len>=GetRxPacketShiftBytes819xUsb(&stats, true)) {
u8 tmpCRC = 0, tmpICV = 0;
//RT_TRACE(COMP_RECV,"%s:aggred pkt,total_len = %d\n",__FUNCTION__,agg_skb->len);
RxDescr = (rx_desc_819x_usb_aggr_subframe *)(agg_skb->data);
tmpCRC = RxDescr->CRC32;
tmpICV = RxDescr->ICV;
memcpy(agg_skb->data, &agg_skb->data[44], 2);
RxDescr->CRC32 = tmpCRC;
RxDescr->ICV = tmpICV;
memset(&stats, 0, sizeof(struct ieee80211_rx_stats));
stats.signal = 0;
stats.noise = -98;
stats.rate = 0;
stats.freq = IEEE80211_24GHZ_BAND;
query_rxdesc_status(agg_skb, &stats, true);
PacketLength = stats.Length;
if(PacketLength > agg_skb->len) {
break;
}
/* Process the MPDU recevied */
skb = dev_alloc_skb(PacketLength);
memcpy(skb_put(skb,PacketLength),agg_skb->data, PacketLength);
skb_trim(skb, skb->len - 4/*sCrcLng*/);
rx_pkt_len = skb->len;
ieee80211_hdr = (struct ieee80211_hdr_1addr *)skb->data;
unicast_packet = false;
if(is_broadcast_ether_addr(ieee80211_hdr->addr1)) {
//TODO
}else if(is_multicast_ether_addr(ieee80211_hdr->addr1)){
//TODO
}else {
/* unicast packet */
unicast_packet = true;
}
if(!ieee80211_rx(priv->ieee80211,skb, &stats)) {
dev_kfree_skb_any(skb);
} else {
priv->stats.rxoktotal++;
if(unicast_packet) {
priv->stats.rxbytesunicast += rx_pkt_len;
}
}
/* should trim the packet which has been copied to target skb */
skb_pull(agg_skb, PacketLength);
PacketShiftBytes = GetRxPacketShiftBytes819xUsb(&stats, true);
PacketOccupiedLendth = PacketLength + PacketShiftBytes;
if ((PacketOccupiedLendth & 0xFF) != 0) {
PaddingBytes = 256 - (PacketOccupiedLendth & 0xFF);
if (agg_skb->len > PaddingBytes)
skb_pull(agg_skb, PaddingBytes);
else
agg_skb->len = 0;
}
}
dev_kfree_skb(agg_skb);
}
#endif
} else {
priv->stats.rxurberr++;
printk("actual_length:%d\n", skb->len);
dev_kfree_skb_any(skb);
}
}
void
rtl819xusb_process_received_packet(
struct net_device *dev,
struct ieee80211_rx_stats *pstats
)
{
// bool bfreerfd=false, bqueued=false;
u8* frame;
u16 frame_len=0;
struct r8192_priv *priv = ieee80211_priv(dev);
// u8 index = 0;
// u8 TID = 0;
//u16 seqnum = 0;
//PRX_TS_RECORD pts = NULL;
// Get shifted bytes of Starting address of 802.11 header. 2006.09.28, by Emily
//porting by amy 080508
pstats->virtual_address += get_rxpacket_shiftbytes_819xusb(pstats);
frame = pstats->virtual_address;
frame_len = pstats->packetlength;
#ifdef TODO // by amy about HCT
if(!Adapter->bInHctTest)
CountRxErrStatistics(Adapter, pRfd);
#endif
{
#ifdef ENABLE_PS //by amy for adding ps function in future
RT_RF_POWER_STATE rtState;
// When RF is off, we should not count the packet for hw/sw synchronize
// reason, ie. there may be a duration while sw switch is changed and hw
// switch is being changed. 2006.12.04, by shien chang.
Adapter->HalFunc.GetHwRegHandler(Adapter, HW_VAR_RF_STATE, (u8* )(&rtState));
if (rtState == eRfOff)
{
return;
}
#endif
priv->stats.rxframgment++;
}
#ifdef TODO
RmMonitorSignalStrength(Adapter, pRfd);
#endif
/* 2007/01/16 MH Add RX command packet handle here. */
/* 2007/03/01 MH We have to release RFD and return if rx pkt is cmd pkt. */
if (rtl819xusb_rx_command_packet(dev, pstats))
{
return;
}
#ifdef SW_CRC_CHECK
SwCrcCheck();
#endif
}
void query_rx_cmdpkt_desc_status(struct sk_buff *skb, struct ieee80211_rx_stats *stats)
{
// rtl8192_rx_info *info = (struct rtl8192_rx_info *)skb->cb;
// struct net_device *dev=info->dev;
// struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
rx_desc_819x_usb *desc = (rx_desc_819x_usb *)skb->data;
// rx_drvinfo_819x_usb *driver_info;
//
//Get Rx Descriptor Information
//
stats->virtual_address = (u8*)skb->data;
stats->Length = desc->Length;
stats->RxDrvInfoSize = 0;
stats->RxBufShift = 0;
stats->packetlength = stats->Length-scrclng;
stats->fraglength = stats->packetlength;
stats->fragoffset = 0;
stats->ntotalfrag = 1;
}
void rtl8192_rx_cmd(struct sk_buff *skb)
{
struct rtl8192_rx_info *info = (struct rtl8192_rx_info *)skb->cb;
struct net_device *dev = info->dev;
//int ret;
// struct urb *rx_urb = info->urb;
/* TODO */
struct ieee80211_rx_stats stats = {
.signal = 0,
.noise = -98,
.rate = 0,
// .mac_time = jiffies,
.freq = IEEE80211_24GHZ_BAND,
};
if((skb->len >=(20 + sizeof(rx_desc_819x_usb))) && (skb->len < RX_URB_SIZE))
{
query_rx_cmdpkt_desc_status(skb,&stats);
// this is to be done by amy 080508 prfd->queue_id = 1;
//
// Process the command packet received.
//
rtl819xusb_process_received_packet(dev,&stats);
dev_kfree_skb_any(skb);
}
else
;
}
void rtl8192_irq_rx_tasklet(struct r8192_priv *priv)
{
struct sk_buff *skb;
struct rtl8192_rx_info *info;
while (NULL != (skb = skb_dequeue(&priv->skb_queue))) {
info = (struct rtl8192_rx_info *)skb->cb;
switch (info->out_pipe) {
/* Nomal packet pipe */
case 3:
//RT_TRACE(COMP_RECV, "normal in-pipe index(%d)\n",info->out_pipe);
priv->IrpPendingCount--;
rtl8192_rx_nomal(skb);
break;
/* Command packet pipe */
case 9:
RT_TRACE(COMP_RECV, "command in-pipe index(%d)\n",\
info->out_pipe);
rtl8192_rx_cmd(skb);
break;
default: /* should never get here! */
RT_TRACE(COMP_ERR, "Unknown in-pipe index(%d)\n",\
info->out_pipe);
dev_kfree_skb(skb);
break;
}
}
}
static const struct net_device_ops rtl8192_netdev_ops = {
.ndo_open = rtl8192_open,
.ndo_stop = rtl8192_close,
.ndo_get_stats = rtl8192_stats,
.ndo_tx_timeout = tx_timeout,
.ndo_do_ioctl = rtl8192_ioctl,
.ndo_set_multicast_list = r8192_set_multicast,
.ndo_set_mac_address = r8192_set_mac_adr,
.ndo_validate_addr = eth_validate_addr,
.ndo_change_mtu = eth_change_mtu,
.ndo_start_xmit = ieee80211_xmit,
};
/****************************************************************************
---------------------------- USB_STUFF---------------------------
*****************************************************************************/
static int __devinit rtl8192_usb_probe(struct usb_interface *intf,
const struct usb_device_id *id)
{
// unsigned long ioaddr = 0;
struct net_device *dev = NULL;
struct r8192_priv *priv= NULL;
struct usb_device *udev = interface_to_usbdev(intf);
int ret;
RT_TRACE(COMP_INIT, "Oops: i'm coming\n");
dev = alloc_ieee80211(sizeof(struct r8192_priv));
if (dev == NULL)
return -ENOMEM;
usb_set_intfdata(intf, dev);
SET_NETDEV_DEV(dev, &intf->dev);
priv = ieee80211_priv(dev);
priv->ieee80211 = netdev_priv(dev);
priv->udev=udev;
dev->netdev_ops = &rtl8192_netdev_ops;
//DMESG("Oops: i'm coming\n");
#if WIRELESS_EXT >= 12
#if WIRELESS_EXT < 17
dev->get_wireless_stats = r8192_get_wireless_stats;
#endif
dev->wireless_handlers = (struct iw_handler_def *) &r8192_wx_handlers_def;
#endif
dev->type=ARPHRD_ETHER;
dev->watchdog_timeo = HZ*3; //modified by john, 0805
if (dev_alloc_name(dev, ifname) < 0){
RT_TRACE(COMP_INIT, "Oops: devname already taken! Trying wlan%%d...\n");
ifname = "wlan%d";
dev_alloc_name(dev, ifname);
}
RT_TRACE(COMP_INIT, "Driver probe completed1\n");
if(rtl8192_init(dev)!=0){
RT_TRACE(COMP_ERR, "Initialization failed");
ret = -ENODEV;
goto fail;
}
netif_carrier_off(dev);
netif_stop_queue(dev);
ret = register_netdev(dev);
if (ret)
goto fail2;
RT_TRACE(COMP_INIT, "dev name=======> %s\n",dev->name);
rtl8192_proc_init_one(dev);
RT_TRACE(COMP_INIT, "Driver probe completed\n");
return 0;
fail2:
rtl8192_down(dev);
kfree(priv->pFirmware);
priv->pFirmware = NULL;
rtl8192_usb_deleteendpoints(dev);
destroy_workqueue(priv->priv_wq);
mdelay(10);
fail:
free_ieee80211(dev);
RT_TRACE(COMP_ERR, "wlan driver load failed\n");
return ret;
}
//detach all the work and timer structure declared or inititialize in r8192U_init function.
void rtl8192_cancel_deferred_work(struct r8192_priv* priv)
{
cancel_work_sync(&priv->reset_wq);
cancel_delayed_work(&priv->watch_dog_wq);
cancel_delayed_work(&priv->update_beacon_wq);
cancel_work_sync(&priv->qos_activate);
//cancel_work_sync(&priv->SetBWModeWorkItem);
//cancel_work_sync(&priv->SwChnlWorkItem);
}
static void __devexit rtl8192_usb_disconnect(struct usb_interface *intf)
{
struct net_device *dev = usb_get_intfdata(intf);
struct r8192_priv *priv = ieee80211_priv(dev);
if(dev){
unregister_netdev(dev);
RT_TRACE(COMP_DOWN, "=============>wlan driver to be removed\n");
rtl8192_proc_remove_one(dev);
rtl8192_down(dev);
kfree(priv->pFirmware);
priv->pFirmware = NULL;
// priv->rf_close(dev);
// rtl8192_SetRFPowerState(dev, eRfOff);
rtl8192_usb_deleteendpoints(dev);
destroy_workqueue(priv->priv_wq);
//rtl8192_irq_disable(dev);
//rtl8192_reset(dev);
mdelay(10);
}
free_ieee80211(dev);
RT_TRACE(COMP_DOWN, "wlan driver removed\n");
}
/* fun with the built-in ieee80211 stack... */
extern int ieee80211_debug_init(void);
extern void ieee80211_debug_exit(void);
extern int ieee80211_crypto_init(void);
extern void ieee80211_crypto_deinit(void);
extern int ieee80211_crypto_tkip_init(void);
extern void ieee80211_crypto_tkip_exit(void);
extern int ieee80211_crypto_ccmp_init(void);
extern void ieee80211_crypto_ccmp_exit(void);
extern int ieee80211_crypto_wep_init(void);
extern void ieee80211_crypto_wep_exit(void);
static int __init rtl8192_usb_module_init(void)
{
int ret;
#ifdef CONFIG_IEEE80211_DEBUG
ret = ieee80211_debug_init();
if (ret) {
printk(KERN_ERR "ieee80211_debug_init() failed %d\n", ret);
return ret;
}
#endif
ret = ieee80211_crypto_init();
if (ret) {
printk(KERN_ERR "ieee80211_crypto_init() failed %d\n", ret);
return ret;
}
ret = ieee80211_crypto_tkip_init();
if (ret) {
printk(KERN_ERR "ieee80211_crypto_tkip_init() failed %d\n",
ret);
return ret;
}
ret = ieee80211_crypto_ccmp_init();
if (ret) {
printk(KERN_ERR "ieee80211_crypto_ccmp_init() failed %d\n",
ret);
return ret;
}
ret = ieee80211_crypto_wep_init();
if (ret) {
printk(KERN_ERR "ieee80211_crypto_wep_init() failed %d\n", ret);
return ret;
}
printk(KERN_INFO "\nLinux kernel driver for RTL8192 based WLAN cards\n");
printk(KERN_INFO "Copyright (c) 2007-2008, Realsil Wlan\n");
RT_TRACE(COMP_INIT, "Initializing module");
RT_TRACE(COMP_INIT, "Wireless extensions version %d", WIRELESS_EXT);
rtl8192_proc_module_init();
return usb_register(&rtl8192_usb_driver);
}
static void __exit rtl8192_usb_module_exit(void)
{
usb_deregister(&rtl8192_usb_driver);
RT_TRACE(COMP_DOWN, "Exiting");
// rtl8192_proc_module_remove();
}
void rtl8192_try_wake_queue(struct net_device *dev, int pri)
{
unsigned long flags;
short enough_desc;
struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
spin_lock_irqsave(&priv->tx_lock,flags);
enough_desc = check_nic_enough_desc(dev,pri);
spin_unlock_irqrestore(&priv->tx_lock,flags);
if(enough_desc)
ieee80211_wake_queue(priv->ieee80211);
}
void EnableHWSecurityConfig8192(struct net_device *dev)
{
u8 SECR_value = 0x0;
struct r8192_priv *priv = (struct r8192_priv *)ieee80211_priv(dev);
struct ieee80211_device* ieee = priv->ieee80211;
SECR_value = SCR_TxEncEnable | SCR_RxDecEnable;
if (((KEY_TYPE_WEP40 == ieee->pairwise_key_type) || (KEY_TYPE_WEP104 == ieee->pairwise_key_type)) && (priv->ieee80211->auth_mode != 2))
{
SECR_value |= SCR_RxUseDK;
SECR_value |= SCR_TxUseDK;
}
else if ((ieee->iw_mode == IW_MODE_ADHOC) && (ieee->pairwise_key_type & (KEY_TYPE_CCMP | KEY_TYPE_TKIP)))
{
SECR_value |= SCR_RxUseDK;
SECR_value |= SCR_TxUseDK;
}
//add HWSec active enable here.
//default using hwsec. when peer AP is in N mode only and pairwise_key_type is none_aes(which HT_IOT_ACT_PURE_N_MODE indicates it), use software security. when peer AP is in b,g,n mode mixed and pairwise_key_type is none_aes, use g mode hw security. WB on 2008.7.4
ieee->hwsec_active = 1;
if ((ieee->pHTInfo->IOTAction&HT_IOT_ACT_PURE_N_MODE) || !hwwep)//!ieee->hwsec_support) //add hwsec_support flag to totol control hw_sec on/off
{
ieee->hwsec_active = 0;
SECR_value &= ~SCR_RxDecEnable;
}
RT_TRACE(COMP_SEC,"%s:, hwsec:%d, pairwise_key:%d, SECR_value:%x\n", __FUNCTION__, \
ieee->hwsec_active, ieee->pairwise_key_type, SECR_value);
{
write_nic_byte(dev, SECR, SECR_value);//SECR_value | SCR_UseDK );
}
}
void setKey( struct net_device *dev,
u8 EntryNo,
u8 KeyIndex,
u16 KeyType,
u8 *MacAddr,
u8 DefaultKey,
u32 *KeyContent )
{
u32 TargetCommand = 0;
u32 TargetContent = 0;
u16 usConfig = 0;
u8 i;
if (EntryNo >= TOTAL_CAM_ENTRY)
RT_TRACE(COMP_ERR, "cam entry exceeds in setKey()\n");
RT_TRACE(COMP_SEC, "====>to setKey(), dev:%p, EntryNo:%d, KeyIndex:%d, KeyType:%d, MacAddr%pM\n", dev,EntryNo, KeyIndex, KeyType, MacAddr);
if (DefaultKey)
usConfig |= BIT15 | (KeyType<<2);
else
usConfig |= BIT15 | (KeyType<<2) | KeyIndex;
// usConfig |= BIT15 | (KeyType<<2) | (DefaultKey<<5) | KeyIndex;
for(i=0 ; i<CAM_CONTENT_COUNT; i++){
TargetCommand = i+CAM_CONTENT_COUNT*EntryNo;
TargetCommand |= BIT31|BIT16;
if(i==0){//MAC|Config
TargetContent = (u32)(*(MacAddr+0)) << 16|
(u32)(*(MacAddr+1)) << 24|
(u32)usConfig;
write_nic_dword(dev, WCAMI, TargetContent);
write_nic_dword(dev, RWCAM, TargetCommand);
// printk("setkey cam =%8x\n", read_cam(dev, i+6*EntryNo));
}
else if(i==1){//MAC
TargetContent = (u32)(*(MacAddr+2)) |
(u32)(*(MacAddr+3)) << 8|
(u32)(*(MacAddr+4)) << 16|
(u32)(*(MacAddr+5)) << 24;
write_nic_dword(dev, WCAMI, TargetContent);
write_nic_dword(dev, RWCAM, TargetCommand);
}
else {
//Key Material
if(KeyContent !=NULL){
write_nic_dword(dev, WCAMI, (u32)(*(KeyContent+i-2)) );
write_nic_dword(dev, RWCAM, TargetCommand);
}
}
}
}
/***************************************************************************
------------------- module init / exit stubs ----------------
****************************************************************************/
module_init(rtl8192_usb_module_init);
module_exit(rtl8192_usb_module_exit);