/*
* Copyright (c) 2001 "Crazy" James Simmons jsimmons@transvirtual.com
*
* Sponsored by Transvirtual Technology.
*
* Derived from the code in h3600_ts.[ch] by Charles Flynn
*/
/*
* Driver for the h3600 Touch Screen and other Atmel controlled devices.
*/
/*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
* Should you need to contact me, the author, you can do so by
* e-mail - mail your message to <jsimmons@transvirtual.com>.
*/
#include <linux/errno.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/slab.h>
#include <linux/input.h>
#include <linux/serio.h>
#include <linux/init.h>
#include <linux/delay.h>
/* SA1100 serial defines */
#include <mach/hardware.h>
#include <mach/irqs.h>
#define DRIVER_DESC "H3600 touchscreen driver"
MODULE_AUTHOR("James Simmons <jsimmons@transvirtual.com>");
MODULE_DESCRIPTION(DRIVER_DESC);
MODULE_LICENSE("GPL");
/*
* Definitions & global arrays.
*/
/* The start and end of frame characters SOF and EOF */
#define CHAR_SOF 0x02
#define CHAR_EOF 0x03
#define FRAME_OVERHEAD 3 /* CHAR_SOF,CHAR_EOF,LENGTH = 3 */
/*
Atmel events and response IDs contained in frame.
Programmer has no control over these numbers.
TODO there are holes - specifically 1,7,0x0a
*/
#define VERSION_ID 0 /* Get Version (request/response) */
#define KEYBD_ID 2 /* Keyboard (event) */
#define TOUCHS_ID 3 /* Touch Screen (event)*/
#define EEPROM_READ_ID 4 /* (request/response) */
#define EEPROM_WRITE_ID 5 /* (request/response) */
#define THERMAL_ID 6 /* (request/response) */
#define NOTIFY_LED_ID 8 /* (request/response) */
#define BATTERY_ID 9 /* (request/response) */
#define SPI_READ_ID 0x0b /* ( request/response) */
#define SPI_WRITE_ID 0x0c /* ( request/response) */
#define FLITE_ID 0x0d /* backlight ( request/response) */
#define STX_ID 0xa1 /* extension pack status (req/resp) */
#define MAX_ID 14
#define H3600_MAX_LENGTH 16
#define H3600_KEY 0xf
#define H3600_SCANCODE_RECORD 1 /* 1 -> record button */
#define H3600_SCANCODE_CALENDAR 2 /* 2 -> calendar */
#define H3600_SCANCODE_CONTACTS 3 /* 3 -> contact */
#define H3600_SCANCODE_Q 4 /* 4 -> Q button */
#define H3600_SCANCODE_START 5 /* 5 -> start menu */
#define H3600_SCANCODE_UP 6 /* 6 -> up */
#define H3600_SCANCODE_RIGHT 7 /* 7 -> right */
#define H3600_SCANCODE_LEFT 8 /* 8 -> left */
#define H3600_SCANCODE_DOWN 9 /* 9 -> down */
/*
* Per-touchscreen data.
*/
struct h3600_dev {
struct input_dev *dev;
struct serio *serio;
unsigned char event; /* event ID from packet */
unsigned char chksum;
unsigned char len;
unsigned char idx;
unsigned char buf[H3600_MAX_LENGTH];
char phys[32];
};
static irqreturn_t action_button_handler(int irq, void *dev_id)
{
int down = (GPLR & GPIO_BITSY_ACTION_BUTTON) ? 0 : 1;
struct input_dev *dev = dev_id;
input_report_key(dev, KEY_ENTER, down);
input_sync(dev);
return IRQ_HANDLED;
}
static irqreturn_t npower_button_handler(int irq, void *dev_id)
{
int down = (GPLR & GPIO_BITSY_NPOWER_BUTTON) ? 0 : 1;
struct input_dev *dev = dev_id;
/*
* This interrupt is only called when we release the key. So we have
* to fake a key press.
*/
input_report_key(dev, KEY_SUSPEND, 1);
input_report_key(dev, KEY_SUSPEND, down);
input_sync(dev);
return IRQ_HANDLED;
}
#ifdef CONFIG_PM
static int flite_brightness = 25;
enum flite_pwr {
FLITE_PWR_OFF = 0,
FLITE_PWR_ON = 1
};
/*
* h3600_flite_power: enables or disables power to frontlight, using last bright */
unsigned int h3600_flite_power(struct input_dev *dev, enum flite_pwr pwr)
{
unsigned char brightness = (pwr == FLITE_PWR_OFF) ? 0 : flite_brightness;
struct h3600_dev *ts = input_get_drvdata(dev);
/* Must be in this order */
serio_write(ts->serio, 1);
serio_write(ts->serio, pwr);
serio_write(ts->serio, brightness);
return 0;
}
#endif
/*
* This function translates the native event packets to linux input event
* packets. Some packets coming from serial are not touchscreen related. In
* this case we send them off to be processed elsewhere.
*/
static void h3600ts_process_packet(struct h3600_dev *ts)
{
struct input_dev *dev = ts->dev;
static int touched = 0;
int key, down = 0;
switch (ts->event) {
/*
Buttons - returned as a single byte
7 6 5 4 3 2 1 0
S x x x N N N N
S switch state ( 0=pressed 1=released)
x Unused.
NNNN switch number 0-15
Note: This is true for non interrupt generated key events.
*/
case KEYBD_ID:
down = (ts->buf[0] & 0x80) ? 0 : 1;
switch (ts->buf[0] & 0x7f) {
case H3600_SCANCODE_RECORD:
key = KEY_RECORD;
break;
case H3600_SCANCODE_CALENDAR:
key = KEY_PROG1;
break;
case H3600_SCANCODE_CONTACTS:
key = KEY_PROG2;
break;
case H3600_SCANCODE_Q:
key = KEY_Q;
break;
case H3600_SCANCODE_START:
key = KEY_PROG3;
break;
case H3600_SCANCODE_UP:
key = KEY_UP;
break;
case H3600_SCANCODE_RIGHT:
key = KEY_RIGHT;
break;
case H3600_SCANCODE_LEFT:
key = KEY_LEFT;
break;
case H3600_SCANCODE_DOWN:
key = KEY_DOWN;
break;
default:
key = 0;
}
if (key)
input_report_key(dev, key, down);
break;
/*
* Native touchscreen event data is formatted as shown below:-
*
* +-------+-------+-------+-------+
* | Xmsb | Xlsb | Ymsb | Ylsb |
* +-------+-------+-------+-------+
* byte 0 1 2 3
*/
case TOUCHS_ID:
if (!touched) {
input_report_key(dev, BTN_TOUCH, 1);
touched = 1;
}
if (ts->len) {
unsigned short x, y;
x = ts->buf[0]; x <<= 8; x += ts->buf[1];
y = ts->buf[2]; y <<= 8; y += ts->buf[3];
input_report_abs(dev, ABS_X, x);
input_report_abs(dev, ABS_Y, y);
} else {
input_report_key(dev, BTN_TOUCH, 0);
touched = 0;
}
break;
default:
/* Send a non input event elsewhere */
break;
}
input_sync(dev);
}
/*
* h3600ts_event() handles events from the input module.
*/
static int h3600ts_event(struct input_dev *dev, unsigned int type,
unsigned int code, int value)
{
#if 0
struct h3600_dev *ts = input_get_drvdata(dev);
switch (type) {
case EV_LED: {
// serio_write(ts->serio, SOME_CMD);
return 0;
}
}
return -1;
#endif
return 0;
}
/*
Frame format
byte 1 2 3 len + 4
+-------+---------------+---------------+--=------------+
|SOF |id |len | len bytes | Chksum |
+-------+---------------+---------------+--=------------+
bit 0 7 8 11 12 15 16
+-------+---------------+-------+
|SOF |id |0 |Chksum | - Note Chksum does not include SOF
+-------+---------------+-------+
bit 0 7 8 11 12 15 16
*/
static int state;
/* decode States */
#define STATE_SOF 0 /* start of FRAME */
#define STATE_ID 1 /* state where we decode the ID & len */
#define STATE_DATA 2 /* state where we decode data */
#define STATE_EOF 3 /* state where we decode checksum or EOF */
static irqreturn_t h3600ts_interrupt(struct serio *serio, unsigned char data,
unsigned int flags)
{
struct h3600_dev *ts = serio_get_drvdata(serio);
/*
* We have a new frame coming in.
*/
switch (state) {
case STATE_SOF:
if (data == CHAR_SOF)
state = STATE_ID;
break;
case STATE_ID:
ts->event = (data & 0xf0) >> 4;
ts->len = (data & 0xf);
ts->idx = 0;
if (ts->event >= MAX_ID) {
state = STATE_SOF;
break;
}
ts->chksum = data;
state = (ts->len > 0) ? STATE_DATA : STATE_EOF;
break;
case STATE_DATA:
ts->chksum += data;
ts->buf[ts->idx]= data;
if (++ts->idx == ts->len)
state = STATE_EOF;
break;
case STATE_EOF:
state = STATE_SOF;
if (data == CHAR_EOF || data == ts->chksum)
h3600ts_process_packet(ts);
break;
default:
printk("Error3\n");
break;
}
return IRQ_HANDLED;
}
/*
* h3600ts_connect() is the routine that is called when someone adds a
* new serio device that supports H3600 protocol and registers it as
* an input device.
*/
static int h3600ts_connect(struct serio *serio, struct serio_driver *drv)
{
struct h3600_dev *ts;
struct input_dev *input_dev;
int err;
ts = kzalloc(sizeof(struct h3600_dev), GFP_KERNEL);
input_dev = input_allocate_device();
if (!ts || !input_dev) {
err = -ENOMEM;
goto fail1;
}
ts->serio = serio;
ts->dev = input_dev;
snprintf(ts->phys, sizeof(ts->phys), "%s/input0", serio->phys);
input_dev->name = "H3600 TouchScreen";
input_dev->phys = ts->phys;
input_dev->id.bustype = BUS_RS232;
input_dev->id.vendor = SERIO_H3600;
input_dev->id.product = 0x0666; /* FIXME !!! We can ask the hardware */
input_dev->id.version = 0x0100;
input_dev->dev.parent = &serio->dev;
input_set_drvdata(input_dev, ts);
input_dev->event = h3600ts_event;
input_dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS) |
BIT_MASK(EV_LED) | BIT_MASK(EV_PWR);
input_dev->ledbit[0] = BIT_MASK(LED_SLEEP);
input_set_abs_params(input_dev, ABS_X, 60, 985, 0, 0);
input_set_abs_params(input_dev, ABS_Y, 35, 1024, 0, 0);
set_bit(KEY_RECORD, input_dev->keybit);
set_bit(KEY_Q, input_dev->keybit);
set_bit(KEY_PROG1, input_dev->keybit);
set_bit(KEY_PROG2, input_dev->keybit);
set_bit(KEY_PROG3, input_dev->keybit);
set_bit(KEY_UP, input_dev->keybit);
set_bit(KEY_RIGHT, input_dev->keybit);
set_bit(KEY_LEFT, input_dev->keybit);
set_bit(KEY_DOWN, input_dev->keybit);
set_bit(KEY_ENTER, input_dev->keybit);
set_bit(KEY_SUSPEND, input_dev->keybit);
set_bit(BTN_TOUCH, input_dev->keybit);
/* Device specific stuff */
set_GPIO_IRQ_edge(GPIO_BITSY_ACTION_BUTTON, GPIO_BOTH_EDGES);
set_GPIO_IRQ_edge(GPIO_BITSY_NPOWER_BUTTON, GPIO_RISING_EDGE);
if (request_irq(IRQ_GPIO_BITSY_ACTION_BUTTON, action_button_handler,
IRQF_SHARED | IRQF_DISABLED, "h3600_action", ts->dev)) {
printk(KERN_ERR "h3600ts.c: Could not allocate Action Button IRQ!\n");
err = -EBUSY;
goto fail1;
}
if (request_irq(IRQ_GPIO_BITSY_NPOWER_BUTTON, npower_button_handler,
IRQF_SHARED | IRQF_DISABLED, "h3600_suspend", ts->dev)) {
printk(KERN_ERR "h3600ts.c: Could not allocate Power Button IRQ!\n");
err = -EBUSY;
goto fail2;
}
serio_set_drvdata(serio, ts);
err = serio_open(serio, drv);
if (err)
goto fail3;
//h3600_flite_control(1, 25); /* default brightness */
err = input_register_device(ts->dev);
if (err)
goto fail4;
return 0;
fail4: serio_close(serio);
fail3: serio_set_drvdata(serio, NULL);
free_irq(IRQ_GPIO_BITSY_NPOWER_BUTTON, ts->dev);
fail2: free_irq(IRQ_GPIO_BITSY_ACTION_BUTTON, ts->dev);
fail1: input_free_device(input_dev);
kfree(ts);
return err;
}
/*
* h3600ts_disconnect() is the opposite of h3600ts_connect()
*/
static void h3600ts_disconnect(struct serio *serio)
{
struct h3600_dev *ts = serio_get_drvdata(serio);
free_irq(IRQ_GPIO_BITSY_ACTION_BUTTON, ts->dev);
free_irq(IRQ_GPIO_BITSY_NPOWER_BUTTON, ts->dev);
input_get_device(ts->dev);
input_unregister_device(ts->dev);
serio_close(serio);
serio_set_drvdata(serio, NULL);
input_put_device(ts->dev);
kfree(ts);
}
/*
* The serio driver structure.
*/
static struct serio_device_id h3600ts_serio_ids[] = {
{
.type = SERIO_RS232,
.proto = SERIO_H3600,
.id = SERIO_ANY,
.extra = SERIO_ANY,
},
{ 0 }
};
MODULE_DEVICE_TABLE(serio, h3600ts_serio_ids);
static struct serio_driver h3600ts_drv = {
.driver = {
.name = "h3600ts",
},
.description = DRIVER_DESC,
.id_table = h3600ts_serio_ids,
.interrupt = h3600ts_interrupt,
.connect = h3600ts_connect,
.disconnect = h3600ts_disconnect,
};
/*
* The functions for inserting/removing us as a module.
*/
static int __init h3600ts_init(void)
{
return serio_register_driver(&h3600ts_drv);
}
static void __exit h3600ts_exit(void)
{
serio_unregister_driver(&h3600ts_drv);
}
module_init(h3600ts_init);
module_exit(h3600ts_exit);