- 根目录:
- drivers
- usb
- host
- ohci-at91.c
/*
* OHCI HCD (Host Controller Driver) for USB.
*
* Copyright (C) 2004 SAN People (Pty) Ltd.
* Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org>
*
* AT91 Bus Glue
*
* Based on fragments of 2.4 driver by Rick Bronson.
* Based on ohci-omap.c
*
* This file is licenced under the GPL.
*/
#include <linux/clk.h>
#include <linux/platform_device.h>
#include <mach/hardware.h>
#include <asm/gpio.h>
#include <mach/board.h>
#include <mach/cpu.h>
#ifndef CONFIG_ARCH_AT91
#error "CONFIG_ARCH_AT91 must be defined."
#endif
/* interface and function clocks; sometimes also an AHB clock */
static struct clk *iclk, *fclk, *hclk;
static int clocked;
extern int usb_disabled(void);
/*-------------------------------------------------------------------------*/
static void at91_start_clock(void)
{
if (cpu_is_at91sam9261() || cpu_is_at91sam9g10())
clk_enable(hclk);
clk_enable(iclk);
clk_enable(fclk);
clocked = 1;
}
static void at91_stop_clock(void)
{
clk_disable(fclk);
clk_disable(iclk);
if (cpu_is_at91sam9261() || cpu_is_at91sam9g10())
clk_disable(hclk);
clocked = 0;
}
static void at91_start_hc(struct platform_device *pdev)
{
struct usb_hcd *hcd = platform_get_drvdata(pdev);
struct ohci_regs __iomem *regs = hcd->regs;
dev_dbg(&pdev->dev, "start\n");
/*
* Start the USB clocks.
*/
at91_start_clock();
/*
* The USB host controller must remain in reset.
*/
writel(0, ®s->control);
}
static void at91_stop_hc(struct platform_device *pdev)
{
struct usb_hcd *hcd = platform_get_drvdata(pdev);
struct ohci_regs __iomem *regs = hcd->regs;
dev_dbg(&pdev->dev, "stop\n");
/*
* Put the USB host controller into reset.
*/
writel(0, ®s->control);
/*
* Stop the USB clocks.
*/
at91_stop_clock();
}
/*-------------------------------------------------------------------------*/
static void usb_hcd_at91_remove (struct usb_hcd *, struct platform_device *);
/* configure so an HC device and id are always provided */
/* always called with process context; sleeping is OK */
/**
* usb_hcd_at91_probe - initialize AT91-based HCDs
* Context: !in_interrupt()
*
* Allocates basic resources for this USB host controller, and
* then invokes the start() method for the HCD associated with it
* through the hotplug entry's driver_data.
*/
static int usb_hcd_at91_probe(const struct hc_driver *driver,
struct platform_device *pdev)
{
int retval;
struct usb_hcd *hcd = NULL;
if (pdev->num_resources != 2) {
pr_debug("hcd probe: invalid num_resources");
return -ENODEV;
}
if ((pdev->resource[0].flags != IORESOURCE_MEM)
|| (pdev->resource[1].flags != IORESOURCE_IRQ)) {
pr_debug("hcd probe: invalid resource type\n");
return -ENODEV;
}
hcd = usb_create_hcd(driver, &pdev->dev, "at91");
if (!hcd)
return -ENOMEM;
hcd->rsrc_start = pdev->resource[0].start;
hcd->rsrc_len = pdev->resource[0].end - pdev->resource[0].start + 1;
if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
pr_debug("request_mem_region failed\n");
retval = -EBUSY;
goto err1;
}
hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
if (!hcd->regs) {
pr_debug("ioremap failed\n");
retval = -EIO;
goto err2;
}
iclk = clk_get(&pdev->dev, "ohci_clk");
fclk = clk_get(&pdev->dev, "uhpck");
if (cpu_is_at91sam9261() || cpu_is_at91sam9g10())
hclk = clk_get(&pdev->dev, "hck0");
at91_start_hc(pdev);
ohci_hcd_init(hcd_to_ohci(hcd));
retval = usb_add_hcd(hcd, pdev->resource[1].start, IRQF_SHARED);
if (retval == 0)
return retval;
/* Error handling */
at91_stop_hc(pdev);
if (cpu_is_at91sam9261() || cpu_is_at91sam9g10())
clk_put(hclk);
clk_put(fclk);
clk_put(iclk);
iounmap(hcd->regs);
err2:
release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
err1:
usb_put_hcd(hcd);
return retval;
}
/* may be called with controller, bus, and devices active */
/**
* usb_hcd_at91_remove - shutdown processing for AT91-based HCDs
* @dev: USB Host Controller being removed
* Context: !in_interrupt()
*
* Reverses the effect of usb_hcd_at91_probe(), first invoking
* the HCD's stop() method. It is always called from a thread
* context, "rmmod" or something similar.
*
*/
static void usb_hcd_at91_remove(struct usb_hcd *hcd,
struct platform_device *pdev)
{
usb_remove_hcd(hcd);
at91_stop_hc(pdev);
iounmap(hcd->regs);
release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
usb_put_hcd(hcd);
if (cpu_is_at91sam9261() || cpu_is_at91sam9g10())
clk_put(hclk);
clk_put(fclk);
clk_put(iclk);
fclk = iclk = hclk = NULL;
dev_set_drvdata(&pdev->dev, NULL);
}
/*-------------------------------------------------------------------------*/
static int __devinit
ohci_at91_start (struct usb_hcd *hcd)
{
struct at91_usbh_data *board = hcd->self.controller->platform_data;
struct ohci_hcd *ohci = hcd_to_ohci (hcd);
int ret;
if ((ret = ohci_init(ohci)) < 0)
return ret;
ohci->num_ports = board->ports;
if ((ret = ohci_run(ohci)) < 0) {
err("can't start %s", hcd->self.bus_name);
ohci_stop(hcd);
return ret;
}
return 0;
}
/*-------------------------------------------------------------------------*/
static const struct hc_driver ohci_at91_hc_driver = {
.description = hcd_name,
.product_desc = "AT91 OHCI",
.hcd_priv_size = sizeof(struct ohci_hcd),
/*
* generic hardware linkage
*/
.irq = ohci_irq,
.flags = HCD_USB11 | HCD_MEMORY,
/*
* basic lifecycle operations
*/
.start = ohci_at91_start,
.stop = ohci_stop,
.shutdown = ohci_shutdown,
/*
* managing i/o requests and associated device resources
*/
.urb_enqueue = ohci_urb_enqueue,
.urb_dequeue = ohci_urb_dequeue,
.endpoint_disable = ohci_endpoint_disable,
/*
* scheduling support
*/
.get_frame_number = ohci_get_frame,
/*
* root hub support
*/
.hub_status_data = ohci_hub_status_data,
.hub_control = ohci_hub_control,
#ifdef CONFIG_PM
.bus_suspend = ohci_bus_suspend,
.bus_resume = ohci_bus_resume,
#endif
.start_port_reset = ohci_start_port_reset,
};
/*-------------------------------------------------------------------------*/
static int ohci_hcd_at91_drv_probe(struct platform_device *pdev)
{
struct at91_usbh_data *pdata = pdev->dev.platform_data;
int i;
if (pdata) {
/* REVISIT make the driver support per-port power switching,
* and also overcurrent detection. Here we assume the ports
* are always powered while this driver is active, and use
* active-low power switches.
*/
for (i = 0; i < ARRAY_SIZE(pdata->vbus_pin); i++) {
if (pdata->vbus_pin[i] <= 0)
continue;
gpio_request(pdata->vbus_pin[i], "ohci_vbus");
gpio_direction_output(pdata->vbus_pin[i], 0);
}
}
device_init_wakeup(&pdev->dev, 1);
return usb_hcd_at91_probe(&ohci_at91_hc_driver, pdev);
}
static int ohci_hcd_at91_drv_remove(struct platform_device *pdev)
{
struct at91_usbh_data *pdata = pdev->dev.platform_data;
int i;
if (pdata) {
for (i = 0; i < ARRAY_SIZE(pdata->vbus_pin); i++) {
if (pdata->vbus_pin[i] <= 0)
continue;
gpio_direction_output(pdata->vbus_pin[i], 1);
gpio_free(pdata->vbus_pin[i]);
}
}
device_init_wakeup(&pdev->dev, 0);
usb_hcd_at91_remove(platform_get_drvdata(pdev), pdev);
return 0;
}
#ifdef CONFIG_PM
static int
ohci_hcd_at91_drv_suspend(struct platform_device *pdev, pm_message_t mesg)
{
struct usb_hcd *hcd = platform_get_drvdata(pdev);
struct ohci_hcd *ohci = hcd_to_ohci(hcd);
if (device_may_wakeup(&pdev->dev))
enable_irq_wake(hcd->irq);
/*
* The integrated transceivers seem unable to notice disconnect,
* reconnect, or wakeup without the 48 MHz clock active. so for
* correctness, always discard connection state (using reset).
*
* REVISIT: some boards will be able to turn VBUS off...
*/
if (at91_suspend_entering_slow_clock()) {
ohci_usb_reset (ohci);
/* flush the writes */
(void) ohci_readl (ohci, &ohci->regs->control);
at91_stop_clock();
}
return 0;
}
static int ohci_hcd_at91_drv_resume(struct platform_device *pdev)
{
struct usb_hcd *hcd = platform_get_drvdata(pdev);
if (device_may_wakeup(&pdev->dev))
disable_irq_wake(hcd->irq);
if (!clocked)
at91_start_clock();
ohci_finish_controller_resume(hcd);
return 0;
}
#else
#define ohci_hcd_at91_drv_suspend NULL
#define ohci_hcd_at91_drv_resume NULL
#endif
MODULE_ALIAS("platform:at91_ohci");
static struct platform_driver ohci_hcd_at91_driver = {
.probe = ohci_hcd_at91_drv_probe,
.remove = ohci_hcd_at91_drv_remove,
.shutdown = usb_hcd_platform_shutdown,
.suspend = ohci_hcd_at91_drv_suspend,
.resume = ohci_hcd_at91_drv_resume,
.driver = {
.name = "at91_ohci",
.owner = THIS_MODULE,
},
};