- 根目录:
- drivers
- staging
- et131x
- et1310_eeprom.c
/*
* Agere Systems Inc.
* 10/100/1000 Base-T Ethernet Driver for the ET1301 and ET131x series MACs
*
* Copyright © 2005 Agere Systems Inc.
* All rights reserved.
* http://www.agere.com
*
*------------------------------------------------------------------------------
*
* et1310_eeprom.c - Code used to access the device's EEPROM
*
*------------------------------------------------------------------------------
*
* SOFTWARE LICENSE
*
* This software is provided subject to the following terms and conditions,
* which you should read carefully before using the software. Using this
* software indicates your acceptance of these terms and conditions. If you do
* not agree with these terms and conditions, do not use the software.
*
* Copyright © 2005 Agere Systems Inc.
* All rights reserved.
*
* Redistribution and use in source or binary forms, with or without
* modifications, are permitted provided that the following conditions are met:
*
* . Redistributions of source code must retain the above copyright notice, this
* list of conditions and the following Disclaimer as comments in the code as
* well as in the documentation and/or other materials provided with the
* distribution.
*
* . Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following Disclaimer in the documentation
* and/or other materials provided with the distribution.
*
* . Neither the name of Agere Systems Inc. nor the names of the contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* Disclaimer
*
* THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES,
* INCLUDING, BUT NOT LIMITED TO, INFRINGEMENT AND THE IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. ANY
* USE, MODIFICATION OR DISTRIBUTION OF THIS SOFTWARE IS SOLELY AT THE USERS OWN
* RISK. IN NO EVENT SHALL AGERE SYSTEMS INC. OR CONTRIBUTORS BE LIABLE FOR ANY
* DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
* ON ANY THEORY OF LIABILITY, INCLUDING, BUT NOT LIMITED TO, CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
* OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
* DAMAGE.
*
*/
#include "et131x_version.h"
#include "et131x_defs.h"
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/module.h>
#include <linux/types.h>
#include <linux/kernel.h>
#include <linux/sched.h>
#include <linux/ptrace.h>
#include <linux/ctype.h>
#include <linux/string.h>
#include <linux/timer.h>
#include <linux/interrupt.h>
#include <linux/in.h>
#include <linux/delay.h>
#include <linux/bitops.h>
#include <linux/io.h>
#include <asm/system.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/skbuff.h>
#include <linux/if_arp.h>
#include <linux/ioport.h>
#include "et1310_phy.h"
#include "et131x_adapter.h"
#include "et131x.h"
/*
* EEPROM Defines
*/
/* LBCIF Register Groups (addressed via 32-bit offsets) */
#define LBCIF_DWORD0_GROUP 0xAC
#define LBCIF_DWORD1_GROUP 0xB0
/* LBCIF Registers (addressed via 8-bit offsets) */
#define LBCIF_ADDRESS_REGISTER 0xAC
#define LBCIF_DATA_REGISTER 0xB0
#define LBCIF_CONTROL_REGISTER 0xB1
#define LBCIF_STATUS_REGISTER 0xB2
/* LBCIF Control Register Bits */
#define LBCIF_CONTROL_SEQUENTIAL_READ 0x01
#define LBCIF_CONTROL_PAGE_WRITE 0x02
#define LBCIF_CONTROL_EEPROM_RELOAD 0x08
#define LBCIF_CONTROL_TWO_BYTE_ADDR 0x20
#define LBCIF_CONTROL_I2C_WRITE 0x40
#define LBCIF_CONTROL_LBCIF_ENABLE 0x80
/* LBCIF Status Register Bits */
#define LBCIF_STATUS_PHY_QUEUE_AVAIL 0x01
#define LBCIF_STATUS_I2C_IDLE 0x02
#define LBCIF_STATUS_ACK_ERROR 0x04
#define LBCIF_STATUS_GENERAL_ERROR 0x08
#define LBCIF_STATUS_CHECKSUM_ERROR 0x40
#define LBCIF_STATUS_EEPROM_PRESENT 0x80
/* Miscellaneous Constraints */
#define MAX_NUM_REGISTER_POLLS 1000
#define MAX_NUM_WRITE_RETRIES 2
static int eeprom_wait_ready(struct pci_dev *pdev, u32 *status)
{
u32 reg;
int i;
/*
* 1. Check LBCIF Status Register for bits 6 & 3:2 all equal to 0 and
* bits 7,1:0 both equal to 1, at least once after reset.
* Subsequent operations need only to check that bits 1:0 are equal
* to 1 prior to starting a single byte read/write
*/
for (i = 0; i < MAX_NUM_REGISTER_POLLS; i++) {
/* Read registers grouped in DWORD1 */
if (pci_read_config_dword(pdev, LBCIF_DWORD1_GROUP, ®))
return -EIO;
/* I2C idle and Phy Queue Avail both true */
if ((reg & 0x3000) == 0x3000) {
if (status)
*status = reg;
return reg & 0xFF;
}
}
return -ETIMEDOUT;
}
/**
* eeprom_write - Write a byte to the ET1310's EEPROM
* @etdev: pointer to our private adapter structure
* @addr: the address to write
* @data: the value to write
*
* Returns 1 for a successful write.
*/
static int eeprom_write(struct et131x_adapter *etdev, u32 addr, u8 data)
{
struct pci_dev *pdev = etdev->pdev;
int index = 0;
int retries;
int err = 0;
int i2c_wack = 0;
int writeok = 0;
u32 status;
u32 val = 0;
/*
* For an EEPROM, an I2C single byte write is defined as a START
* condition followed by the device address, EEPROM address, one byte
* of data and a STOP condition. The STOP condition will trigger the
* EEPROM's internally timed write cycle to the nonvolatile memory.
* All inputs are disabled during this write cycle and the EEPROM will
* not respond to any access until the internal write is complete.
*/
err = eeprom_wait_ready(pdev, NULL);
if (err)
return err;
/*
* 2. Write to the LBCIF Control Register: bit 7=1, bit 6=1, bit 3=0,
* and bits 1:0 both =0. Bit 5 should be set according to the
* type of EEPROM being accessed (1=two byte addressing, 0=one
* byte addressing).
*/
if (pci_write_config_byte(pdev, LBCIF_CONTROL_REGISTER,
LBCIF_CONTROL_LBCIF_ENABLE | LBCIF_CONTROL_I2C_WRITE))
return -EIO;
i2c_wack = 1;
/* Prepare EEPROM address for Step 3 */
for (retries = 0; retries < MAX_NUM_WRITE_RETRIES; retries++) {
/* Write the address to the LBCIF Address Register */
if (pci_write_config_dword(pdev, LBCIF_ADDRESS_REGISTER, addr))
break;
/*
* Write the data to the LBCIF Data Register (the I2C write
* will begin).
*/
if (pci_write_config_byte(pdev, LBCIF_DATA_REGISTER, data))
break;
/*
* Monitor bit 1:0 of the LBCIF Status Register. When bits
* 1:0 are both equal to 1, the I2C write has completed and the
* internal write cycle of the EEPROM is about to start.
* (bits 1:0 = 01 is a legal state while waiting from both
* equal to 1, but bits 1:0 = 10 is invalid and implies that
* something is broken).
*/
err = eeprom_wait_ready(pdev, &status);
if (err < 0)
return 0;
/*
* Check bit 3 of the LBCIF Status Register. If equal to 1,
* an error has occurred.Don't break here if we are revision
* 1, this is so we do a blind write for load bug.
*/
if ((status & LBCIF_STATUS_GENERAL_ERROR)
&& etdev->pdev->revision == 0)
break;
/*
* Check bit 2 of the LBCIF Status Register. If equal to 1 an
* ACK error has occurred on the address phase of the write.
* This could be due to an actual hardware failure or the
* EEPROM may still be in its internal write cycle from a
* previous write. This write operation was ignored and must be
*repeated later.
*/
if (status & LBCIF_STATUS_ACK_ERROR) {
/*
* This could be due to an actual hardware failure
* or the EEPROM may still be in its internal write
* cycle from a previous write. This write operation
* was ignored and must be repeated later.
*/
udelay(10);
continue;
}
writeok = 1;
break;
}
/*
* Set bit 6 of the LBCIF Control Register = 0.
*/
udelay(10);
while (i2c_wack) {
if (pci_write_config_byte(pdev, LBCIF_CONTROL_REGISTER,
LBCIF_CONTROL_LBCIF_ENABLE))
writeok = 0;
/* Do read until internal ACK_ERROR goes away meaning write
* completed
*/
do {
pci_write_config_dword(pdev,
LBCIF_ADDRESS_REGISTER,
addr);
do {
pci_read_config_dword(pdev,
LBCIF_DATA_REGISTER, &val);
} while ((val & 0x00010000) == 0);
} while (val & 0x00040000);
if ((val & 0xFF00) != 0xC000 || index == 10000)
break;
index++;
}
return writeok ? 0 : -EIO;
}
/**
* eeprom_read - Read a byte from the ET1310's EEPROM
* @etdev: pointer to our private adapter structure
* @addr: the address from which to read
* @pdata: a pointer to a byte in which to store the value of the read
* @eeprom_id: the ID of the EEPROM
* @addrmode: how the EEPROM is to be accessed
*
* Returns 1 for a successful read
*/
static int eeprom_read(struct et131x_adapter *etdev, u32 addr, u8 *pdata)
{
struct pci_dev *pdev = etdev->pdev;
int err;
u32 status;
/*
* A single byte read is similar to the single byte write, with the
* exception of the data flow:
*/
err = eeprom_wait_ready(pdev, NULL);
if (err)
return err;
/*
* Write to the LBCIF Control Register: bit 7=1, bit 6=0, bit 3=0,
* and bits 1:0 both =0. Bit 5 should be set according to the type
* of EEPROM being accessed (1=two byte addressing, 0=one byte
* addressing).
*/
if (pci_write_config_byte(pdev, LBCIF_CONTROL_REGISTER,
LBCIF_CONTROL_LBCIF_ENABLE))
return -EIO;
/*
* Write the address to the LBCIF Address Register (I2C read will
* begin).
*/
if (pci_write_config_dword(pdev, LBCIF_ADDRESS_REGISTER, addr))
return -EIO;
/*
* Monitor bit 0 of the LBCIF Status Register. When = 1, I2C read
* is complete. (if bit 1 =1 and bit 0 stays = 0, a hardware failure
* has occurred).
*/
err = eeprom_wait_ready(pdev, &status);
if (err < 0)
return err;
/*
* Regardless of error status, read data byte from LBCIF Data
* Register.
*/
*pdata = err;
/*
* Check bit 2 of the LBCIF Status Register. If = 1,
* then an error has occurred.
*/
return (status & LBCIF_STATUS_ACK_ERROR) ? -EIO : 0;
}
int et131x_init_eeprom(struct et131x_adapter *etdev)
{
struct pci_dev *pdev = etdev->pdev;
u8 eestatus;
/* We first need to check the EEPROM Status code located at offset
* 0xB2 of config space
*/
pci_read_config_byte(pdev, ET1310_PCI_EEPROM_STATUS,
&eestatus);
/* THIS IS A WORKAROUND:
* I need to call this function twice to get my card in a
* LG M1 Express Dual running. I tried also a msleep before this
* function, because I thougth there could be some time condidions
* but it didn't work. Call the whole function twice also work.
*/
if (pci_read_config_byte(pdev, ET1310_PCI_EEPROM_STATUS, &eestatus)) {
dev_err(&pdev->dev,
"Could not read PCI config space for EEPROM Status\n");
return -EIO;
}
/* Determine if the error(s) we care about are present. If they are
* present we need to fail.
*/
if (eestatus & 0x4C) {
int write_failed = 0;
if (pdev->revision == 0x01) {
int i;
static const u8 eedata[4] = { 0xFE, 0x13, 0x10, 0xFF };
/* Re-write the first 4 bytes if we have an eeprom
* present and the revision id is 1, this fixes the
* corruption seen with 1310 B Silicon
*/
for (i = 0; i < 3; i++)
if (eeprom_write(etdev, i, eedata[i]) < 0)
write_failed = 1;
}
if (pdev->revision != 0x01 || write_failed) {
dev_err(&pdev->dev,
"Fatal EEPROM Status Error - 0x%04x\n", eestatus);
/* This error could mean that there was an error
* reading the eeprom or that the eeprom doesn't exist.
* We will treat each case the same and not try to
* gather additional information that normally would
* come from the eeprom, like MAC Address
*/
etdev->has_eeprom = 0;
return -EIO;
}
}
etdev->has_eeprom = 1;
/* Read the EEPROM for information regarding LED behavior. Refer to
* ET1310_phy.c, et131x_xcvr_init(), for its use.
*/
eeprom_read(etdev, 0x70, &etdev->eeprom_data[0]);
eeprom_read(etdev, 0x71, &etdev->eeprom_data[1]);
if (etdev->eeprom_data[0] != 0xcd)
/* Disable all optional features */
etdev->eeprom_data[1] = 0x00;
return 0;
}