/*
* Driver for Cirrus Logic EP93xx SPI controller.
*
* Copyright (c) 2010 Mika Westerberg
*
* Explicit FIFO handling code was inspired by amba-pl022 driver.
*
* Chip select support using other than built-in GPIOs by H. Hartley Sweeten.
*
* For more information about the SPI controller see documentation on Cirrus
* Logic web site:
* http://www.cirrus.com/en/pubs/manual/EP93xx_Users_Guide_UM1.pdf
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/io.h>
#include <linux/clk.h>
#include <linux/err.h>
#include <linux/delay.h>
#include <linux/device.h>
#include <linux/bitops.h>
#include <linux/interrupt.h>
#include <linux/platform_device.h>
#include <linux/workqueue.h>
#include <linux/sched.h>
#include <linux/spi/spi.h>
#include <mach/ep93xx_spi.h>
#define SSPCR0 0x0000
#define SSPCR0_MODE_SHIFT 6
#define SSPCR0_SCR_SHIFT 8
#define SSPCR1 0x0004
#define SSPCR1_RIE BIT(0)
#define SSPCR1_TIE BIT(1)
#define SSPCR1_RORIE BIT(2)
#define SSPCR1_LBM BIT(3)
#define SSPCR1_SSE BIT(4)
#define SSPCR1_MS BIT(5)
#define SSPCR1_SOD BIT(6)
#define SSPDR 0x0008
#define SSPSR 0x000c
#define SSPSR_TFE BIT(0)
#define SSPSR_TNF BIT(1)
#define SSPSR_RNE BIT(2)
#define SSPSR_RFF BIT(3)
#define SSPSR_BSY BIT(4)
#define SSPCPSR 0x0010
#define SSPIIR 0x0014
#define SSPIIR_RIS BIT(0)
#define SSPIIR_TIS BIT(1)
#define SSPIIR_RORIS BIT(2)
#define SSPICR SSPIIR
/* timeout in milliseconds */
#define SPI_TIMEOUT 5
/* maximum depth of RX/TX FIFO */
#define SPI_FIFO_SIZE 8
/**
* struct ep93xx_spi - EP93xx SPI controller structure
* @lock: spinlock that protects concurrent accesses to fields @running,
* @current_msg and @msg_queue
* @pdev: pointer to platform device
* @clk: clock for the controller
* @regs_base: pointer to ioremap()'d registers
* @irq: IRQ number used by the driver
* @min_rate: minimum clock rate (in Hz) supported by the controller
* @max_rate: maximum clock rate (in Hz) supported by the controller
* @running: is the queue running
* @wq: workqueue used by the driver
* @msg_work: work that is queued for the driver
* @wait: wait here until given transfer is completed
* @msg_queue: queue for the messages
* @current_msg: message that is currently processed (or %NULL if none)
* @tx: current byte in transfer to transmit
* @rx: current byte in transfer to receive
* @fifo_level: how full is FIFO (%0..%SPI_FIFO_SIZE - %1). Receiving one
* frame decreases this level and sending one frame increases it.
*
* This structure holds EP93xx SPI controller specific information. When
* @running is %true, driver accepts transfer requests from protocol drivers.
* @current_msg is used to hold pointer to the message that is currently
* processed. If @current_msg is %NULL, it means that no processing is going
* on.
*
* Most of the fields are only written once and they can be accessed without
* taking the @lock. Fields that are accessed concurrently are: @current_msg,
* @running, and @msg_queue.
*/
struct ep93xx_spi {
spinlock_t lock;
const struct platform_device *pdev;
struct clk *clk;
void __iomem *regs_base;
int irq;
unsigned long min_rate;
unsigned long max_rate;
bool running;
struct workqueue_struct *wq;
struct work_struct msg_work;
struct completion wait;
struct list_head msg_queue;
struct spi_message *current_msg;
size_t tx;
size_t rx;
size_t fifo_level;
};
/**
* struct ep93xx_spi_chip - SPI device hardware settings
* @spi: back pointer to the SPI device
* @rate: max rate in hz this chip supports
* @div_cpsr: cpsr (pre-scaler) divider
* @div_scr: scr divider
* @dss: bits per word (4 - 16 bits)
* @ops: private chip operations
*
* This structure is used to store hardware register specific settings for each
* SPI device. Settings are written to hardware by function
* ep93xx_spi_chip_setup().
*/
struct ep93xx_spi_chip {
const struct spi_device *spi;
unsigned long rate;
u8 div_cpsr;
u8 div_scr;
u8 dss;
struct ep93xx_spi_chip_ops *ops;
};
/* converts bits per word to CR0.DSS value */
#define bits_per_word_to_dss(bpw) ((bpw) - 1)
static inline void
ep93xx_spi_write_u8(const struct ep93xx_spi *espi, u16 reg, u8 value)
{
__raw_writeb(value, espi->regs_base + reg);
}
static inline u8
ep93xx_spi_read_u8(const struct ep93xx_spi *spi, u16 reg)
{
return __raw_readb(spi->regs_base + reg);
}
static inline void
ep93xx_spi_write_u16(const struct ep93xx_spi *espi, u16 reg, u16 value)
{
__raw_writew(value, espi->regs_base + reg);
}
static inline u16
ep93xx_spi_read_u16(const struct ep93xx_spi *spi, u16 reg)
{
return __raw_readw(spi->regs_base + reg);
}
static int ep93xx_spi_enable(const struct ep93xx_spi *espi)
{
u8 regval;
int err;
err = clk_enable(espi->clk);
if (err)
return err;
regval = ep93xx_spi_read_u8(espi, SSPCR1);
regval |= SSPCR1_SSE;
ep93xx_spi_write_u8(espi, SSPCR1, regval);
return 0;
}
static void ep93xx_spi_disable(const struct ep93xx_spi *espi)
{
u8 regval;
regval = ep93xx_spi_read_u8(espi, SSPCR1);
regval &= ~SSPCR1_SSE;
ep93xx_spi_write_u8(espi, SSPCR1, regval);
clk_disable(espi->clk);
}
static void ep93xx_spi_enable_interrupts(const struct ep93xx_spi *espi)
{
u8 regval;
regval = ep93xx_spi_read_u8(espi, SSPCR1);
regval |= (SSPCR1_RORIE | SSPCR1_TIE | SSPCR1_RIE);
ep93xx_spi_write_u8(espi, SSPCR1, regval);
}
static void ep93xx_spi_disable_interrupts(const struct ep93xx_spi *espi)
{
u8 regval;
regval = ep93xx_spi_read_u8(espi, SSPCR1);
regval &= ~(SSPCR1_RORIE | SSPCR1_TIE | SSPCR1_RIE);
ep93xx_spi_write_u8(espi, SSPCR1, regval);
}
/**
* ep93xx_spi_calc_divisors() - calculates SPI clock divisors
* @espi: ep93xx SPI controller struct
* @chip: divisors are calculated for this chip
* @rate: desired SPI output clock rate
*
* Function calculates cpsr (clock pre-scaler) and scr divisors based on
* given @rate and places them to @chip->div_cpsr and @chip->div_scr. If,
* for some reason, divisors cannot be calculated nothing is stored and
* %-EINVAL is returned.
*/
static int ep93xx_spi_calc_divisors(const struct ep93xx_spi *espi,
struct ep93xx_spi_chip *chip,
unsigned long rate)
{
unsigned long spi_clk_rate = clk_get_rate(espi->clk);
int cpsr, scr;
/*
* Make sure that max value is between values supported by the
* controller. Note that minimum value is already checked in
* ep93xx_spi_transfer().
*/
rate = clamp(rate, espi->min_rate, espi->max_rate);
/*
* Calculate divisors so that we can get speed according the
* following formula:
* rate = spi_clock_rate / (cpsr * (1 + scr))
*
* cpsr must be even number and starts from 2, scr can be any number
* between 0 and 255.
*/
for (cpsr = 2; cpsr <= 254; cpsr += 2) {
for (scr = 0; scr <= 255; scr++) {
if ((spi_clk_rate / (cpsr * (scr + 1))) <= rate) {
chip->div_scr = (u8)scr;
chip->div_cpsr = (u8)cpsr;
return 0;
}
}
}
return -EINVAL;
}
static void ep93xx_spi_cs_control(struct spi_device *spi, bool control)
{
struct ep93xx_spi_chip *chip = spi_get_ctldata(spi);
int value = (spi->mode & SPI_CS_HIGH) ? control : !control;
if (chip->ops && chip->ops->cs_control)
chip->ops->cs_control(spi, value);
}
/**
* ep93xx_spi_setup() - setup an SPI device
* @spi: SPI device to setup
*
* This function sets up SPI device mode, speed etc. Can be called multiple
* times for a single device. Returns %0 in case of success, negative error in
* case of failure. When this function returns success, the device is
* deselected.
*/
static int ep93xx_spi_setup(struct spi_device *spi)
{
struct ep93xx_spi *espi = spi_master_get_devdata(spi->master);
struct ep93xx_spi_chip *chip;
if (spi->bits_per_word < 4 || spi->bits_per_word > 16) {
dev_err(&espi->pdev->dev, "invalid bits per word %d\n",
spi->bits_per_word);
return -EINVAL;
}
chip = spi_get_ctldata(spi);
if (!chip) {
dev_dbg(&espi->pdev->dev, "initial setup for %s\n",
spi->modalias);
chip = kzalloc(sizeof(*chip), GFP_KERNEL);
if (!chip)
return -ENOMEM;
chip->spi = spi;
chip->ops = spi->controller_data;
if (chip->ops && chip->ops->setup) {
int ret = chip->ops->setup(spi);
if (ret) {
kfree(chip);
return ret;
}
}
spi_set_ctldata(spi, chip);
}
if (spi->max_speed_hz != chip->rate) {
int err;
err = ep93xx_spi_calc_divisors(espi, chip, spi->max_speed_hz);
if (err != 0) {
spi_set_ctldata(spi, NULL);
kfree(chip);
return err;
}
chip->rate = spi->max_speed_hz;
}
chip->dss = bits_per_word_to_dss(spi->bits_per_word);
ep93xx_spi_cs_control(spi, false);
return 0;
}
/**
* ep93xx_spi_transfer() - queue message to be transferred
* @spi: target SPI device
* @msg: message to be transferred
*
* This function is called by SPI device drivers when they are going to transfer
* a new message. It simply puts the message in the queue and schedules
* workqueue to perform the actual transfer later on.
*
* Returns %0 on success and negative error in case of failure.
*/
static int ep93xx_spi_transfer(struct spi_device *spi, struct spi_message *msg)
{
struct ep93xx_spi *espi = spi_master_get_devdata(spi->master);
struct spi_transfer *t;
unsigned long flags;
if (!msg || !msg->complete)
return -EINVAL;
/* first validate each transfer */
list_for_each_entry(t, &msg->transfers, transfer_list) {
if (t->bits_per_word) {
if (t->bits_per_word < 4 || t->bits_per_word > 16)
return -EINVAL;
}
if (t->speed_hz && t->speed_hz < espi->min_rate)
return -EINVAL;
}
/*
* Now that we own the message, let's initialize it so that it is
* suitable for us. We use @msg->status to signal whether there was
* error in transfer and @msg->state is used to hold pointer to the
* current transfer (or %NULL if no active current transfer).
*/
msg->state = NULL;
msg->status = 0;
msg->actual_length = 0;
spin_lock_irqsave(&espi->lock, flags);
if (!espi->running) {
spin_unlock_irqrestore(&espi->lock, flags);
return -ESHUTDOWN;
}
list_add_tail(&msg->queue, &espi->msg_queue);
queue_work(espi->wq, &espi->msg_work);
spin_unlock_irqrestore(&espi->lock, flags);
return 0;
}
/**
* ep93xx_spi_cleanup() - cleans up master controller specific state
* @spi: SPI device to cleanup
*
* This function releases master controller specific state for given @spi
* device.
*/
static void ep93xx_spi_cleanup(struct spi_device *spi)
{
struct ep93xx_spi_chip *chip;
chip = spi_get_ctldata(spi);
if (chip) {
if (chip->ops && chip->ops->cleanup)
chip->ops->cleanup(spi);
spi_set_ctldata(spi, NULL);
kfree(chip);
}
}
/**
* ep93xx_spi_chip_setup() - configures hardware according to given @chip
* @espi: ep93xx SPI controller struct
* @chip: chip specific settings
*
* This function sets up the actual hardware registers with settings given in
* @chip. Note that no validation is done so make sure that callers validate
* settings before calling this.
*/
static void ep93xx_spi_chip_setup(const struct ep93xx_spi *espi,
const struct ep93xx_spi_chip *chip)
{
u16 cr0;
cr0 = chip->div_scr << SSPCR0_SCR_SHIFT;
cr0 |= (chip->spi->mode & (SPI_CPHA|SPI_CPOL)) << SSPCR0_MODE_SHIFT;
cr0 |= chip->dss;
dev_dbg(&espi->pdev->dev, "setup: mode %d, cpsr %d, scr %d, dss %d\n",
chip->spi->mode, chip->div_cpsr, chip->div_scr, chip->dss);
dev_dbg(&espi->pdev->dev, "setup: cr0 %#x", cr0);
ep93xx_spi_write_u8(espi, SSPCPSR, chip->div_cpsr);
ep93xx_spi_write_u16(espi, SSPCR0, cr0);
}
static inline int bits_per_word(const struct ep93xx_spi *espi)
{
struct spi_message *msg = espi->current_msg;
struct spi_transfer *t = msg->state;
return t->bits_per_word ? t->bits_per_word : msg->spi->bits_per_word;
}
static void ep93xx_do_write(struct ep93xx_spi *espi, struct spi_transfer *t)
{
if (bits_per_word(espi) > 8) {
u16 tx_val = 0;
if (t->tx_buf)
tx_val = ((u16 *)t->tx_buf)[espi->tx];
ep93xx_spi_write_u16(espi, SSPDR, tx_val);
espi->tx += sizeof(tx_val);
} else {
u8 tx_val = 0;
if (t->tx_buf)
tx_val = ((u8 *)t->tx_buf)[espi->tx];
ep93xx_spi_write_u8(espi, SSPDR, tx_val);
espi->tx += sizeof(tx_val);
}
}
static void ep93xx_do_read(struct ep93xx_spi *espi, struct spi_transfer *t)
{
if (bits_per_word(espi) > 8) {
u16 rx_val;
rx_val = ep93xx_spi_read_u16(espi, SSPDR);
if (t->rx_buf)
((u16 *)t->rx_buf)[espi->rx] = rx_val;
espi->rx += sizeof(rx_val);
} else {
u8 rx_val;
rx_val = ep93xx_spi_read_u8(espi, SSPDR);
if (t->rx_buf)
((u8 *)t->rx_buf)[espi->rx] = rx_val;
espi->rx += sizeof(rx_val);
}
}
/**
* ep93xx_spi_read_write() - perform next RX/TX transfer
* @espi: ep93xx SPI controller struct
*
* This function transfers next bytes (or half-words) to/from RX/TX FIFOs. If
* called several times, the whole transfer will be completed. Returns
* %-EINPROGRESS when current transfer was not yet completed otherwise %0.
*
* When this function is finished, RX FIFO should be empty and TX FIFO should be
* full.
*/
static int ep93xx_spi_read_write(struct ep93xx_spi *espi)
{
struct spi_message *msg = espi->current_msg;
struct spi_transfer *t = msg->state;
/* read as long as RX FIFO has frames in it */
while ((ep93xx_spi_read_u8(espi, SSPSR) & SSPSR_RNE)) {
ep93xx_do_read(espi, t);
espi->fifo_level--;
}
/* write as long as TX FIFO has room */
while (espi->fifo_level < SPI_FIFO_SIZE && espi->tx < t->len) {
ep93xx_do_write(espi, t);
espi->fifo_level++;
}
if (espi->rx == t->len) {
msg->actual_length += t->len;
return 0;
}
return -EINPROGRESS;
}
/**
* ep93xx_spi_process_transfer() - processes one SPI transfer
* @espi: ep93xx SPI controller struct
* @msg: current message
* @t: transfer to process
*
* This function processes one SPI transfer given in @t. Function waits until
* transfer is complete (may sleep) and updates @msg->status based on whether
* transfer was successfully processed or not.
*/
static void ep93xx_spi_process_transfer(struct ep93xx_spi *espi,
struct spi_message *msg,
struct spi_transfer *t)
{
struct ep93xx_spi_chip *chip = spi_get_ctldata(msg->spi);
msg->state = t;
/*
* Handle any transfer specific settings if needed. We use
* temporary chip settings here and restore original later when
* the transfer is finished.
*/
if (t->speed_hz || t->bits_per_word) {
struct ep93xx_spi_chip tmp_chip = *chip;
if (t->speed_hz) {
int err;
err = ep93xx_spi_calc_divisors(espi, &tmp_chip,
t->speed_hz);
if (err) {
dev_err(&espi->pdev->dev,
"failed to adjust speed\n");
msg->status = err;
return;
}
}
if (t->bits_per_word)
tmp_chip.dss = bits_per_word_to_dss(t->bits_per_word);
/*
* Set up temporary new hw settings for this transfer.
*/
ep93xx_spi_chip_setup(espi, &tmp_chip);
}
espi->rx = 0;
espi->tx = 0;
/*
* Now everything is set up for the current transfer. We prime the TX
* FIFO, enable interrupts, and wait for the transfer to complete.
*/
if (ep93xx_spi_read_write(espi)) {
ep93xx_spi_enable_interrupts(espi);
wait_for_completion(&espi->wait);
}
/*
* In case of error during transmit, we bail out from processing
* the message.
*/
if (msg->status)
return;
/*
* After this transfer is finished, perform any possible
* post-transfer actions requested by the protocol driver.
*/
if (t->delay_usecs) {
set_current_state(TASK_UNINTERRUPTIBLE);
schedule_timeout(usecs_to_jiffies(t->delay_usecs));
}
if (t->cs_change) {
if (!list_is_last(&t->transfer_list, &msg->transfers)) {
/*
* In case protocol driver is asking us to drop the
* chipselect briefly, we let the scheduler to handle
* any "delay" here.
*/
ep93xx_spi_cs_control(msg->spi, false);
cond_resched();
ep93xx_spi_cs_control(msg->spi, true);
}
}
if (t->speed_hz || t->bits_per_word)
ep93xx_spi_chip_setup(espi, chip);
}
/*
* ep93xx_spi_process_message() - process one SPI message
* @espi: ep93xx SPI controller struct
* @msg: message to process
*
* This function processes a single SPI message. We go through all transfers in
* the message and pass them to ep93xx_spi_process_transfer(). Chipselect is
* asserted during the whole message (unless per transfer cs_change is set).
*
* @msg->status contains %0 in case of success or negative error code in case of
* failure.
*/
static void ep93xx_spi_process_message(struct ep93xx_spi *espi,
struct spi_message *msg)
{
unsigned long timeout;
struct spi_transfer *t;
int err;
/*
* Enable the SPI controller and its clock.
*/
err = ep93xx_spi_enable(espi);
if (err) {
dev_err(&espi->pdev->dev, "failed to enable SPI controller\n");
msg->status = err;
return;
}
/*
* Just to be sure: flush any data from RX FIFO.
*/
timeout = jiffies + msecs_to_jiffies(SPI_TIMEOUT);
while (ep93xx_spi_read_u16(espi, SSPSR) & SSPSR_RNE) {
if (time_after(jiffies, timeout)) {
dev_warn(&espi->pdev->dev,
"timeout while flushing RX FIFO\n");
msg->status = -ETIMEDOUT;
return;
}
ep93xx_spi_read_u16(espi, SSPDR);
}
/*
* We explicitly handle FIFO level. This way we don't have to check TX
* FIFO status using %SSPSR_TNF bit which may cause RX FIFO overruns.
*/
espi->fifo_level = 0;
/*
* Update SPI controller registers according to spi device and assert
* the chipselect.
*/
ep93xx_spi_chip_setup(espi, spi_get_ctldata(msg->spi));
ep93xx_spi_cs_control(msg->spi, true);
list_for_each_entry(t, &msg->transfers, transfer_list) {
ep93xx_spi_process_transfer(espi, msg, t);
if (msg->status)
break;
}
/*
* Now the whole message is transferred (or failed for some reason). We
* deselect the device and disable the SPI controller.
*/
ep93xx_spi_cs_control(msg->spi, false);
ep93xx_spi_disable(espi);
}
#define work_to_espi(work) (container_of((work), struct ep93xx_spi, msg_work))
/**
* ep93xx_spi_work() - EP93xx SPI workqueue worker function
* @work: work struct
*
* Workqueue worker function. This function is called when there are new
* SPI messages to be processed. Message is taken out from the queue and then
* passed to ep93xx_spi_process_message().
*
* After message is transferred, protocol driver is notified by calling
* @msg->complete(). In case of error, @msg->status is set to negative error
* number, otherwise it contains zero (and @msg->actual_length is updated).
*/
static void ep93xx_spi_work(struct work_struct *work)
{
struct ep93xx_spi *espi = work_to_espi(work);
struct spi_message *msg;
spin_lock_irq(&espi->lock);
if (!espi->running || espi->current_msg ||
list_empty(&espi->msg_queue)) {
spin_unlock_irq(&espi->lock);
return;
}
msg = list_first_entry(&espi->msg_queue, struct spi_message, queue);
list_del_init(&msg->queue);
espi->current_msg = msg;
spin_unlock_irq(&espi->lock);
ep93xx_spi_process_message(espi, msg);
/*
* Update the current message and re-schedule ourselves if there are
* more messages in the queue.
*/
spin_lock_irq(&espi->lock);
espi->current_msg = NULL;
if (espi->running && !list_empty(&espi->msg_queue))
queue_work(espi->wq, &espi->msg_work);
spin_unlock_irq(&espi->lock);
/* notify the protocol driver that we are done with this message */
msg->complete(msg->context);
}
static irqreturn_t ep93xx_spi_interrupt(int irq, void *dev_id)
{
struct ep93xx_spi *espi = dev_id;
u8 irq_status = ep93xx_spi_read_u8(espi, SSPIIR);
/*
* If we got ROR (receive overrun) interrupt we know that something is
* wrong. Just abort the message.
*/
if (unlikely(irq_status & SSPIIR_RORIS)) {
/* clear the overrun interrupt */
ep93xx_spi_write_u8(espi, SSPICR, 0);
dev_warn(&espi->pdev->dev,
"receive overrun, aborting the message\n");
espi->current_msg->status = -EIO;
} else {
/*
* Interrupt is either RX (RIS) or TX (TIS). For both cases we
* simply execute next data transfer.
*/
if (ep93xx_spi_read_write(espi)) {
/*
* In normal case, there still is some processing left
* for current transfer. Let's wait for the next
* interrupt then.
*/
return IRQ_HANDLED;
}
}
/*
* Current transfer is finished, either with error or with success. In
* any case we disable interrupts and notify the worker to handle
* any post-processing of the message.
*/
ep93xx_spi_disable_interrupts(espi);
complete(&espi->wait);
return IRQ_HANDLED;
}
static int __init ep93xx_spi_probe(struct platform_device *pdev)
{
struct spi_master *master;
struct ep93xx_spi_info *info;
struct ep93xx_spi *espi;
struct resource *res;
int error;
info = pdev->dev.platform_data;
master = spi_alloc_master(&pdev->dev, sizeof(*espi));
if (!master) {
dev_err(&pdev->dev, "failed to allocate spi master\n");
return -ENOMEM;
}
master->setup = ep93xx_spi_setup;
master->transfer = ep93xx_spi_transfer;
master->cleanup = ep93xx_spi_cleanup;
master->bus_num = pdev->id;
master->num_chipselect = info->num_chipselect;
master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
platform_set_drvdata(pdev, master);
espi = spi_master_get_devdata(master);
espi->clk = clk_get(&pdev->dev, NULL);
if (IS_ERR(espi->clk)) {
dev_err(&pdev->dev, "unable to get spi clock\n");
error = PTR_ERR(espi->clk);
goto fail_release_master;
}
spin_lock_init(&espi->lock);
init_completion(&espi->wait);
/*
* Calculate maximum and minimum supported clock rates
* for the controller.
*/
espi->max_rate = clk_get_rate(espi->clk) / 2;
espi->min_rate = clk_get_rate(espi->clk) / (254 * 256);
espi->pdev = pdev;
espi->irq = platform_get_irq(pdev, 0);
if (espi->irq < 0) {
error = -EBUSY;
dev_err(&pdev->dev, "failed to get irq resources\n");
goto fail_put_clock;
}
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!res) {
dev_err(&pdev->dev, "unable to get iomem resource\n");
error = -ENODEV;
goto fail_put_clock;
}
res = request_mem_region(res->start, resource_size(res), pdev->name);
if (!res) {
dev_err(&pdev->dev, "unable to request iomem resources\n");
error = -EBUSY;
goto fail_put_clock;
}
espi->regs_base = ioremap(res->start, resource_size(res));
if (!espi->regs_base) {
dev_err(&pdev->dev, "failed to map resources\n");
error = -ENODEV;
goto fail_free_mem;
}
error = request_irq(espi->irq, ep93xx_spi_interrupt, 0,
"ep93xx-spi", espi);
if (error) {
dev_err(&pdev->dev, "failed to request irq\n");
goto fail_unmap_regs;
}
espi->wq = create_singlethread_workqueue("ep93xx_spid");
if (!espi->wq) {
dev_err(&pdev->dev, "unable to create workqueue\n");
goto fail_free_irq;
}
INIT_WORK(&espi->msg_work, ep93xx_spi_work);
INIT_LIST_HEAD(&espi->msg_queue);
espi->running = true;
/* make sure that the hardware is disabled */
ep93xx_spi_write_u8(espi, SSPCR1, 0);
error = spi_register_master(master);
if (error) {
dev_err(&pdev->dev, "failed to register SPI master\n");
goto fail_free_queue;
}
dev_info(&pdev->dev, "EP93xx SPI Controller at 0x%08lx irq %d\n",
(unsigned long)res->start, espi->irq);
return 0;
fail_free_queue:
destroy_workqueue(espi->wq);
fail_free_irq:
free_irq(espi->irq, espi);
fail_unmap_regs:
iounmap(espi->regs_base);
fail_free_mem:
release_mem_region(res->start, resource_size(res));
fail_put_clock:
clk_put(espi->clk);
fail_release_master:
spi_master_put(master);
platform_set_drvdata(pdev, NULL);
return error;
}
static int __exit ep93xx_spi_remove(struct platform_device *pdev)
{
struct spi_master *master = platform_get_drvdata(pdev);
struct ep93xx_spi *espi = spi_master_get_devdata(master);
struct resource *res;
spin_lock_irq(&espi->lock);
espi->running = false;
spin_unlock_irq(&espi->lock);
destroy_workqueue(espi->wq);
/*
* Complete remaining messages with %-ESHUTDOWN status.
*/
spin_lock_irq(&espi->lock);
while (!list_empty(&espi->msg_queue)) {
struct spi_message *msg;
msg = list_first_entry(&espi->msg_queue,
struct spi_message, queue);
list_del_init(&msg->queue);
msg->status = -ESHUTDOWN;
spin_unlock_irq(&espi->lock);
msg->complete(msg->context);
spin_lock_irq(&espi->lock);
}
spin_unlock_irq(&espi->lock);
free_irq(espi->irq, espi);
iounmap(espi->regs_base);
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
release_mem_region(res->start, resource_size(res));
clk_put(espi->clk);
platform_set_drvdata(pdev, NULL);
spi_unregister_master(master);
return 0;
}
static struct platform_driver ep93xx_spi_driver = {
.driver = {
.name = "ep93xx-spi",
.owner = THIS_MODULE,
},
.remove = __exit_p(ep93xx_spi_remove),
};
static int __init ep93xx_spi_init(void)
{
return platform_driver_probe(&ep93xx_spi_driver, ep93xx_spi_probe);
}
module_init(ep93xx_spi_init);
static void __exit ep93xx_spi_exit(void)
{
platform_driver_unregister(&ep93xx_spi_driver);
}
module_exit(ep93xx_spi_exit);
MODULE_DESCRIPTION("EP93xx SPI Controller driver");
MODULE_AUTHOR("Mika Westerberg <mika.westerberg@iki.fi>");
MODULE_LICENSE("GPL");
MODULE_ALIAS("platform:ep93xx-spi");