/*
* PHY functions
*
* Copyright (c) 2004-2007 Reyk Floeter <reyk@openbsd.org>
* Copyright (c) 2006-2009 Nick Kossifidis <mickflemm@gmail.com>
* Copyright (c) 2007-2008 Jiri Slaby <jirislaby@gmail.com>
* Copyright (c) 2008-2009 Felix Fietkau <nbd@openwrt.org>
*
* Lightly modified for gPXE, July 2009, by Joshua Oreman <oremanj@rwcr.net>.
*
* Permission to use, copy, modify, and distribute this software for any
* purpose with or without fee is hereby granted, provided that the above
* copyright notice and this permission notice appear in all copies.
*
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
*
*/
FILE_LICENCE ( MIT );
#define _ATH5K_PHY
#include <unistd.h>
#include <stdlib.h>
#include "ath5k.h"
#include "reg.h"
#include "base.h"
#include "rfbuffer.h"
#include "rfgain.h"
static inline int min(int x, int y)
{
return (x < y) ? x : y;
}
static inline int max(int x, int y)
{
return (x > y) ? x : y;
}
/*
* Used to modify RF Banks before writing them to AR5K_RF_BUFFER
*/
static unsigned int ath5k_hw_rfb_op(struct ath5k_hw *ah,
const struct ath5k_rf_reg *rf_regs,
u32 val, u8 reg_id, int set)
{
const struct ath5k_rf_reg *rfreg = NULL;
u8 offset, bank, num_bits, col, position;
u16 entry;
u32 mask, data, last_bit, bits_shifted, first_bit;
u32 *rfb;
s32 bits_left;
unsigned i;
data = 0;
rfb = ah->ah_rf_banks;
for (i = 0; i < ah->ah_rf_regs_count; i++) {
if (rf_regs[i].index == reg_id) {
rfreg = &rf_regs[i];
break;
}
}
if (rfb == NULL || rfreg == NULL) {
DBG("ath5k: RF register not found!\n");
/* should not happen */
return 0;
}
bank = rfreg->bank;
num_bits = rfreg->field.len;
first_bit = rfreg->field.pos;
col = rfreg->field.col;
/* first_bit is an offset from bank's
* start. Since we have all banks on
* the same array, we use this offset
* to mark each bank's start */
offset = ah->ah_offset[bank];
/* Boundary check */
if (!(col <= 3 && num_bits <= 32 && first_bit + num_bits <= 319)) {
DBG("ath5k: RF invalid values at offset %d\n", offset);
return 0;
}
entry = ((first_bit - 1) / 8) + offset;
position = (first_bit - 1) % 8;
if (set)
data = ath5k_hw_bitswap(val, num_bits);
for (bits_shifted = 0, bits_left = num_bits; bits_left > 0;
position = 0, entry++) {
last_bit = (position + bits_left > 8) ? 8 :
position + bits_left;
mask = (((1 << last_bit) - 1) ^ ((1 << position) - 1)) <<
(col * 8);
if (set) {
rfb[entry] &= ~mask;
rfb[entry] |= ((data << position) << (col * 8)) & mask;
data >>= (8 - position);
} else {
data |= (((rfb[entry] & mask) >> (col * 8)) >> position)
<< bits_shifted;
bits_shifted += last_bit - position;
}
bits_left -= 8 - position;
}
data = set ? 1 : ath5k_hw_bitswap(data, num_bits);
return data;
}
/**********************\
* RF Gain optimization *
\**********************/
/*
* This code is used to optimize rf gain on different environments
* (temprature mostly) based on feedback from a power detector.
*
* It's only used on RF5111 and RF5112, later RF chips seem to have
* auto adjustment on hw -notice they have a much smaller BANK 7 and
* no gain optimization ladder-.
*
* For more infos check out this patent doc
* http://www.freepatentsonline.com/7400691.html
*
* This paper describes power drops as seen on the receiver due to
* probe packets
* http://www.cnri.dit.ie/publications/ICT08%20-%20Practical%20Issues
* %20of%20Power%20Control.pdf
*
* And this is the MadWiFi bug entry related to the above
* http://madwifi-project.org/ticket/1659
* with various measurements and diagrams
*
* TODO: Deal with power drops due to probes by setting an apropriate
* tx power on the probe packets ! Make this part of the calibration process.
*/
/* Initialize ah_gain durring attach */
int ath5k_hw_rfgain_opt_init(struct ath5k_hw *ah)
{
/* Initialize the gain optimization values */
switch (ah->ah_radio) {
case AR5K_RF5111:
ah->ah_gain.g_step_idx = rfgain_opt_5111.go_default;
ah->ah_gain.g_low = 20;
ah->ah_gain.g_high = 35;
ah->ah_gain.g_state = AR5K_RFGAIN_ACTIVE;
break;
case AR5K_RF5112:
ah->ah_gain.g_step_idx = rfgain_opt_5112.go_default;
ah->ah_gain.g_low = 20;
ah->ah_gain.g_high = 85;
ah->ah_gain.g_state = AR5K_RFGAIN_ACTIVE;
break;
default:
return -EINVAL;
}
return 0;
}
/* Schedule a gain probe check on the next transmited packet.
* That means our next packet is going to be sent with lower
* tx power and a Peak to Average Power Detector (PAPD) will try
* to measure the gain.
*
* TODO: Use propper tx power setting for the probe packet so
* that we don't observe a serious power drop on the receiver
*
* XXX: How about forcing a tx packet (bypassing PCU arbitrator etc)
* just after we enable the probe so that we don't mess with
* standard traffic ? Maybe it's time to use sw interrupts and
* a probe tasklet !!!
*/
static void ath5k_hw_request_rfgain_probe(struct ath5k_hw *ah)
{
/* Skip if gain calibration is inactive or
* we already handle a probe request */
if (ah->ah_gain.g_state != AR5K_RFGAIN_ACTIVE)
return;
/* Send the packet with 2dB below max power as
* patent doc suggest */
ath5k_hw_reg_write(ah, AR5K_REG_SM(ah->ah_txpower.txp_max_pwr - 4,
AR5K_PHY_PAPD_PROBE_TXPOWER) |
AR5K_PHY_PAPD_PROBE_TX_NEXT, AR5K_PHY_PAPD_PROBE);
ah->ah_gain.g_state = AR5K_RFGAIN_READ_REQUESTED;
}
/* Calculate gain_F measurement correction
* based on the current step for RF5112 rev. 2 */
static u32 ath5k_hw_rf_gainf_corr(struct ath5k_hw *ah)
{
u32 mix, step;
u32 *rf;
const struct ath5k_gain_opt *go;
const struct ath5k_gain_opt_step *g_step;
const struct ath5k_rf_reg *rf_regs;
/* Only RF5112 Rev. 2 supports it */
if ((ah->ah_radio != AR5K_RF5112) ||
(ah->ah_radio_5ghz_revision <= AR5K_SREV_RAD_5112A))
return 0;
go = &rfgain_opt_5112;
rf_regs = rf_regs_5112a;
ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5112a);
g_step = &go->go_step[ah->ah_gain.g_step_idx];
if (ah->ah_rf_banks == NULL)
return 0;
rf = ah->ah_rf_banks;
ah->ah_gain.g_f_corr = 0;
/* No VGA (Variable Gain Amplifier) override, skip */
if (ath5k_hw_rfb_op(ah, rf_regs, 0, AR5K_RF_MIXVGA_OVR, 0) != 1)
return 0;
/* Mix gain stepping */
step = ath5k_hw_rfb_op(ah, rf_regs, 0, AR5K_RF_MIXGAIN_STEP, 0);
/* Mix gain override */
mix = g_step->gos_param[0];
switch (mix) {
case 3:
ah->ah_gain.g_f_corr = step * 2;
break;
case 2:
ah->ah_gain.g_f_corr = (step - 5) * 2;
break;
case 1:
ah->ah_gain.g_f_corr = step;
break;
default:
ah->ah_gain.g_f_corr = 0;
break;
}
return ah->ah_gain.g_f_corr;
}
/* Check if current gain_F measurement is in the range of our
* power detector windows. If we get a measurement outside range
* we know it's not accurate (detectors can't measure anything outside
* their detection window) so we must ignore it */
static int ath5k_hw_rf_check_gainf_readback(struct ath5k_hw *ah)
{
const struct ath5k_rf_reg *rf_regs;
u32 step, mix_ovr, level[4];
u32 *rf;
if (ah->ah_rf_banks == NULL)
return 0;
rf = ah->ah_rf_banks;
if (ah->ah_radio == AR5K_RF5111) {
rf_regs = rf_regs_5111;
ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5111);
step = ath5k_hw_rfb_op(ah, rf_regs, 0, AR5K_RF_RFGAIN_STEP,
0);
level[0] = 0;
level[1] = (step == 63) ? 50 : step + 4;
level[2] = (step != 63) ? 64 : level[0];
level[3] = level[2] + 50 ;
ah->ah_gain.g_high = level[3] -
(step == 63 ? AR5K_GAIN_DYN_ADJUST_HI_MARGIN : -5);
ah->ah_gain.g_low = level[0] +
(step == 63 ? AR5K_GAIN_DYN_ADJUST_LO_MARGIN : 0);
} else {
rf_regs = rf_regs_5112;
ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5112);
mix_ovr = ath5k_hw_rfb_op(ah, rf_regs, 0, AR5K_RF_MIXVGA_OVR,
0);
level[0] = level[2] = 0;
if (mix_ovr == 1) {
level[1] = level[3] = 83;
} else {
level[1] = level[3] = 107;
ah->ah_gain.g_high = 55;
}
}
return (ah->ah_gain.g_current >= level[0] &&
ah->ah_gain.g_current <= level[1]) ||
(ah->ah_gain.g_current >= level[2] &&
ah->ah_gain.g_current <= level[3]);
}
/* Perform gain_F adjustment by choosing the right set
* of parameters from rf gain optimization ladder */
static s8 ath5k_hw_rf_gainf_adjust(struct ath5k_hw *ah)
{
const struct ath5k_gain_opt *go;
const struct ath5k_gain_opt_step *g_step;
int ret = 0;
switch (ah->ah_radio) {
case AR5K_RF5111:
go = &rfgain_opt_5111;
break;
case AR5K_RF5112:
go = &rfgain_opt_5112;
break;
default:
return 0;
}
g_step = &go->go_step[ah->ah_gain.g_step_idx];
if (ah->ah_gain.g_current >= ah->ah_gain.g_high) {
/* Reached maximum */
if (ah->ah_gain.g_step_idx == 0)
return -1;
for (ah->ah_gain.g_target = ah->ah_gain.g_current;
ah->ah_gain.g_target >= ah->ah_gain.g_high &&
ah->ah_gain.g_step_idx > 0;
g_step = &go->go_step[ah->ah_gain.g_step_idx])
ah->ah_gain.g_target -= 2 *
(go->go_step[--(ah->ah_gain.g_step_idx)].gos_gain -
g_step->gos_gain);
ret = 1;
goto done;
}
if (ah->ah_gain.g_current <= ah->ah_gain.g_low) {
/* Reached minimum */
if (ah->ah_gain.g_step_idx == (go->go_steps_count - 1))
return -2;
for (ah->ah_gain.g_target = ah->ah_gain.g_current;
ah->ah_gain.g_target <= ah->ah_gain.g_low &&
ah->ah_gain.g_step_idx < go->go_steps_count-1;
g_step = &go->go_step[ah->ah_gain.g_step_idx])
ah->ah_gain.g_target -= 2 *
(go->go_step[++ah->ah_gain.g_step_idx].gos_gain -
g_step->gos_gain);
ret = 2;
goto done;
}
done:
DBG2("ath5k RF adjust: ret %d, gain step %d, current gain %d, "
"target gain %d\n", ret, ah->ah_gain.g_step_idx,
ah->ah_gain.g_current, ah->ah_gain.g_target);
return ret;
}
/* Main callback for thermal rf gain calibration engine
* Check for a new gain reading and schedule an adjustment
* if needed.
*
* TODO: Use sw interrupt to schedule reset if gain_F needs
* adjustment */
enum ath5k_rfgain ath5k_hw_gainf_calibrate(struct ath5k_hw *ah)
{
u32 data, type;
struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom;
if (ah->ah_rf_banks == NULL ||
ah->ah_gain.g_state == AR5K_RFGAIN_INACTIVE)
return AR5K_RFGAIN_INACTIVE;
/* No check requested, either engine is inactive
* or an adjustment is already requested */
if (ah->ah_gain.g_state != AR5K_RFGAIN_READ_REQUESTED)
goto done;
/* Read the PAPD (Peak to Average Power Detector)
* register */
data = ath5k_hw_reg_read(ah, AR5K_PHY_PAPD_PROBE);
/* No probe is scheduled, read gain_F measurement */
if (!(data & AR5K_PHY_PAPD_PROBE_TX_NEXT)) {
ah->ah_gain.g_current = data >> AR5K_PHY_PAPD_PROBE_GAINF_S;
type = AR5K_REG_MS(data, AR5K_PHY_PAPD_PROBE_TYPE);
/* If tx packet is CCK correct the gain_F measurement
* by cck ofdm gain delta */
if (type == AR5K_PHY_PAPD_PROBE_TYPE_CCK) {
if (ah->ah_radio_5ghz_revision >= AR5K_SREV_RAD_5112A)
ah->ah_gain.g_current +=
ee->ee_cck_ofdm_gain_delta;
else
ah->ah_gain.g_current +=
AR5K_GAIN_CCK_PROBE_CORR;
}
/* Further correct gain_F measurement for
* RF5112A radios */
if (ah->ah_radio_5ghz_revision >= AR5K_SREV_RAD_5112A) {
ath5k_hw_rf_gainf_corr(ah);
ah->ah_gain.g_current =
ah->ah_gain.g_current >= ah->ah_gain.g_f_corr ?
(ah->ah_gain.g_current-ah->ah_gain.g_f_corr) :
0;
}
/* Check if measurement is ok and if we need
* to adjust gain, schedule a gain adjustment,
* else switch back to the acive state */
if (ath5k_hw_rf_check_gainf_readback(ah) &&
AR5K_GAIN_CHECK_ADJUST(&ah->ah_gain) &&
ath5k_hw_rf_gainf_adjust(ah)) {
ah->ah_gain.g_state = AR5K_RFGAIN_NEED_CHANGE;
} else {
ah->ah_gain.g_state = AR5K_RFGAIN_ACTIVE;
}
}
done:
return ah->ah_gain.g_state;
}
/* Write initial rf gain table to set the RF sensitivity
* this one works on all RF chips and has nothing to do
* with gain_F calibration */
int ath5k_hw_rfgain_init(struct ath5k_hw *ah, unsigned int freq)
{
const struct ath5k_ini_rfgain *ath5k_rfg;
unsigned int i, size;
switch (ah->ah_radio) {
case AR5K_RF5111:
ath5k_rfg = rfgain_5111;
size = ARRAY_SIZE(rfgain_5111);
break;
case AR5K_RF5112:
ath5k_rfg = rfgain_5112;
size = ARRAY_SIZE(rfgain_5112);
break;
case AR5K_RF2413:
ath5k_rfg = rfgain_2413;
size = ARRAY_SIZE(rfgain_2413);
break;
case AR5K_RF2316:
ath5k_rfg = rfgain_2316;
size = ARRAY_SIZE(rfgain_2316);
break;
case AR5K_RF5413:
ath5k_rfg = rfgain_5413;
size = ARRAY_SIZE(rfgain_5413);
break;
case AR5K_RF2317:
case AR5K_RF2425:
ath5k_rfg = rfgain_2425;
size = ARRAY_SIZE(rfgain_2425);
break;
default:
return -EINVAL;
}
switch (freq) {
case AR5K_INI_RFGAIN_2GHZ:
case AR5K_INI_RFGAIN_5GHZ:
break;
default:
return -EINVAL;
}
for (i = 0; i < size; i++) {
AR5K_REG_WAIT(i);
ath5k_hw_reg_write(ah, ath5k_rfg[i].rfg_value[freq],
(u32)ath5k_rfg[i].rfg_register);
}
return 0;
}
/********************\
* RF Registers setup *
\********************/
/*
* Setup RF registers by writing rf buffer on hw
*/
int ath5k_hw_rfregs_init(struct ath5k_hw *ah, struct net80211_channel *channel,
unsigned int mode)
{
const struct ath5k_rf_reg *rf_regs;
const struct ath5k_ini_rfbuffer *ini_rfb;
const struct ath5k_gain_opt *go = NULL;
const struct ath5k_gain_opt_step *g_step;
struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom;
u8 ee_mode = 0;
u32 *rfb;
int obdb = -1, bank = -1;
unsigned i;
switch (ah->ah_radio) {
case AR5K_RF5111:
rf_regs = rf_regs_5111;
ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5111);
ini_rfb = rfb_5111;
ah->ah_rf_banks_size = ARRAY_SIZE(rfb_5111);
go = &rfgain_opt_5111;
break;
case AR5K_RF5112:
if (ah->ah_radio_5ghz_revision >= AR5K_SREV_RAD_5112A) {
rf_regs = rf_regs_5112a;
ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5112a);
ini_rfb = rfb_5112a;
ah->ah_rf_banks_size = ARRAY_SIZE(rfb_5112a);
} else {
rf_regs = rf_regs_5112;
ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5112);
ini_rfb = rfb_5112;
ah->ah_rf_banks_size = ARRAY_SIZE(rfb_5112);
}
go = &rfgain_opt_5112;
break;
case AR5K_RF2413:
rf_regs = rf_regs_2413;
ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_2413);
ini_rfb = rfb_2413;
ah->ah_rf_banks_size = ARRAY_SIZE(rfb_2413);
break;
case AR5K_RF2316:
rf_regs = rf_regs_2316;
ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_2316);
ini_rfb = rfb_2316;
ah->ah_rf_banks_size = ARRAY_SIZE(rfb_2316);
break;
case AR5K_RF5413:
rf_regs = rf_regs_5413;
ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_5413);
ini_rfb = rfb_5413;
ah->ah_rf_banks_size = ARRAY_SIZE(rfb_5413);
break;
case AR5K_RF2317:
rf_regs = rf_regs_2425;
ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_2425);
ini_rfb = rfb_2317;
ah->ah_rf_banks_size = ARRAY_SIZE(rfb_2317);
break;
case AR5K_RF2425:
rf_regs = rf_regs_2425;
ah->ah_rf_regs_count = ARRAY_SIZE(rf_regs_2425);
if (ah->ah_mac_srev < AR5K_SREV_AR2417) {
ini_rfb = rfb_2425;
ah->ah_rf_banks_size = ARRAY_SIZE(rfb_2425);
} else {
ini_rfb = rfb_2417;
ah->ah_rf_banks_size = ARRAY_SIZE(rfb_2417);
}
break;
default:
return -EINVAL;
}
/* If it's the first time we set rf buffer, allocate
* ah->ah_rf_banks based on ah->ah_rf_banks_size
* we set above */
if (ah->ah_rf_banks == NULL) {
ah->ah_rf_banks = malloc(sizeof(u32) * ah->ah_rf_banks_size);
if (ah->ah_rf_banks == NULL) {
return -ENOMEM;
}
}
/* Copy values to modify them */
rfb = ah->ah_rf_banks;
for (i = 0; i < ah->ah_rf_banks_size; i++) {
if (ini_rfb[i].rfb_bank >= AR5K_MAX_RF_BANKS) {
DBG("ath5k: invalid RF register bank\n");
return -EINVAL;
}
/* Bank changed, write down the offset */
if (bank != ini_rfb[i].rfb_bank) {
bank = ini_rfb[i].rfb_bank;
ah->ah_offset[bank] = i;
}
rfb[i] = ini_rfb[i].rfb_mode_data[mode];
}
/* Set Output and Driver bias current (OB/DB) */
if (channel->hw_value & CHANNEL_2GHZ) {
if (channel->hw_value & CHANNEL_CCK)
ee_mode = AR5K_EEPROM_MODE_11B;
else
ee_mode = AR5K_EEPROM_MODE_11G;
/* For RF511X/RF211X combination we
* use b_OB and b_DB parameters stored
* in eeprom on ee->ee_ob[ee_mode][0]
*
* For all other chips we use OB/DB for 2Ghz
* stored in the b/g modal section just like
* 802.11a on ee->ee_ob[ee_mode][1] */
if ((ah->ah_radio == AR5K_RF5111) ||
(ah->ah_radio == AR5K_RF5112))
obdb = 0;
else
obdb = 1;
ath5k_hw_rfb_op(ah, rf_regs, ee->ee_ob[ee_mode][obdb],
AR5K_RF_OB_2GHZ, 1);
ath5k_hw_rfb_op(ah, rf_regs, ee->ee_db[ee_mode][obdb],
AR5K_RF_DB_2GHZ, 1);
/* RF5111 always needs OB/DB for 5GHz, even if we use 2GHz */
} else if ((channel->hw_value & CHANNEL_5GHZ) ||
(ah->ah_radio == AR5K_RF5111)) {
/* For 11a, Turbo and XR we need to choose
* OB/DB based on frequency range */
ee_mode = AR5K_EEPROM_MODE_11A;
obdb = channel->center_freq >= 5725 ? 3 :
(channel->center_freq >= 5500 ? 2 :
(channel->center_freq >= 5260 ? 1 :
(channel->center_freq > 4000 ? 0 : -1)));
if (obdb < 0)
return -EINVAL;
ath5k_hw_rfb_op(ah, rf_regs, ee->ee_ob[ee_mode][obdb],
AR5K_RF_OB_5GHZ, 1);
ath5k_hw_rfb_op(ah, rf_regs, ee->ee_db[ee_mode][obdb],
AR5K_RF_DB_5GHZ, 1);
}
g_step = &go->go_step[ah->ah_gain.g_step_idx];
/* Bank Modifications (chip-specific) */
if (ah->ah_radio == AR5K_RF5111) {
/* Set gain_F settings according to current step */
if (channel->hw_value & CHANNEL_OFDM) {
AR5K_REG_WRITE_BITS(ah, AR5K_PHY_FRAME_CTL,
AR5K_PHY_FRAME_CTL_TX_CLIP,
g_step->gos_param[0]);
ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[1],
AR5K_RF_PWD_90, 1);
ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[2],
AR5K_RF_PWD_84, 1);
ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[3],
AR5K_RF_RFGAIN_SEL, 1);
/* We programmed gain_F parameters, switch back
* to active state */
ah->ah_gain.g_state = AR5K_RFGAIN_ACTIVE;
}
/* Bank 6/7 setup */
ath5k_hw_rfb_op(ah, rf_regs, !ee->ee_xpd[ee_mode],
AR5K_RF_PWD_XPD, 1);
ath5k_hw_rfb_op(ah, rf_regs, ee->ee_x_gain[ee_mode],
AR5K_RF_XPD_GAIN, 1);
ath5k_hw_rfb_op(ah, rf_regs, ee->ee_i_gain[ee_mode],
AR5K_RF_GAIN_I, 1);
ath5k_hw_rfb_op(ah, rf_regs, ee->ee_xpd[ee_mode],
AR5K_RF_PLO_SEL, 1);
/* TODO: Half/quarter channel support */
}
if (ah->ah_radio == AR5K_RF5112) {
/* Set gain_F settings according to current step */
if (channel->hw_value & CHANNEL_OFDM) {
ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[0],
AR5K_RF_MIXGAIN_OVR, 1);
ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[1],
AR5K_RF_PWD_138, 1);
ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[2],
AR5K_RF_PWD_137, 1);
ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[3],
AR5K_RF_PWD_136, 1);
ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[4],
AR5K_RF_PWD_132, 1);
ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[5],
AR5K_RF_PWD_131, 1);
ath5k_hw_rfb_op(ah, rf_regs, g_step->gos_param[6],
AR5K_RF_PWD_130, 1);
/* We programmed gain_F parameters, switch back
* to active state */
ah->ah_gain.g_state = AR5K_RFGAIN_ACTIVE;
}
/* Bank 6/7 setup */
ath5k_hw_rfb_op(ah, rf_regs, ee->ee_xpd[ee_mode],
AR5K_RF_XPD_SEL, 1);
if (ah->ah_radio_5ghz_revision < AR5K_SREV_RAD_5112A) {
/* Rev. 1 supports only one xpd */
ath5k_hw_rfb_op(ah, rf_regs,
ee->ee_x_gain[ee_mode],
AR5K_RF_XPD_GAIN, 1);
} else {
/* TODO: Set high and low gain bits */
ath5k_hw_rfb_op(ah, rf_regs,
ee->ee_x_gain[ee_mode],
AR5K_RF_PD_GAIN_LO, 1);
ath5k_hw_rfb_op(ah, rf_regs,
ee->ee_x_gain[ee_mode],
AR5K_RF_PD_GAIN_HI, 1);
/* Lower synth voltage on Rev 2 */
ath5k_hw_rfb_op(ah, rf_regs, 2,
AR5K_RF_HIGH_VC_CP, 1);
ath5k_hw_rfb_op(ah, rf_regs, 2,
AR5K_RF_MID_VC_CP, 1);
ath5k_hw_rfb_op(ah, rf_regs, 2,
AR5K_RF_LOW_VC_CP, 1);
ath5k_hw_rfb_op(ah, rf_regs, 2,
AR5K_RF_PUSH_UP, 1);
/* Decrease power consumption on 5213+ BaseBand */
if (ah->ah_phy_revision >= AR5K_SREV_PHY_5212A) {
ath5k_hw_rfb_op(ah, rf_regs, 1,
AR5K_RF_PAD2GND, 1);
ath5k_hw_rfb_op(ah, rf_regs, 1,
AR5K_RF_XB2_LVL, 1);
ath5k_hw_rfb_op(ah, rf_regs, 1,
AR5K_RF_XB5_LVL, 1);
ath5k_hw_rfb_op(ah, rf_regs, 1,
AR5K_RF_PWD_167, 1);
ath5k_hw_rfb_op(ah, rf_regs, 1,
AR5K_RF_PWD_166, 1);
}
}
ath5k_hw_rfb_op(ah, rf_regs, ee->ee_i_gain[ee_mode],
AR5K_RF_GAIN_I, 1);
/* TODO: Half/quarter channel support */
}
if (ah->ah_radio == AR5K_RF5413 &&
channel->hw_value & CHANNEL_2GHZ) {
ath5k_hw_rfb_op(ah, rf_regs, 1, AR5K_RF_DERBY_CHAN_SEL_MODE,
1);
/* Set optimum value for early revisions (on pci-e chips) */
if (ah->ah_mac_srev >= AR5K_SREV_AR5424 &&
ah->ah_mac_srev < AR5K_SREV_AR5413)
ath5k_hw_rfb_op(ah, rf_regs, ath5k_hw_bitswap(6, 3),
AR5K_RF_PWD_ICLOBUF_2G, 1);
}
/* Write RF banks on hw */
for (i = 0; i < ah->ah_rf_banks_size; i++) {
AR5K_REG_WAIT(i);
ath5k_hw_reg_write(ah, rfb[i], ini_rfb[i].rfb_ctrl_register);
}
return 0;
}
/**************************\
PHY/RF channel functions
\**************************/
/*
* Check if a channel is supported
*/
int ath5k_channel_ok(struct ath5k_hw *ah, u16 freq, unsigned int flags)
{
/* Check if the channel is in our supported range */
if (flags & CHANNEL_2GHZ) {
if ((freq >= ah->ah_capabilities.cap_range.range_2ghz_min) &&
(freq <= ah->ah_capabilities.cap_range.range_2ghz_max))
return 1;
} else if (flags & CHANNEL_5GHZ)
if ((freq >= ah->ah_capabilities.cap_range.range_5ghz_min) &&
(freq <= ah->ah_capabilities.cap_range.range_5ghz_max))
return 1;
return 0;
}
/*
* Convertion needed for RF5110
*/
static u32 ath5k_hw_rf5110_chan2athchan(struct net80211_channel *channel)
{
u32 athchan;
/*
* Convert IEEE channel/MHz to an internal channel value used
* by the AR5210 chipset. This has not been verified with
* newer chipsets like the AR5212A who have a completely
* different RF/PHY part.
*/
athchan = (ath5k_hw_bitswap((ath5k_freq_to_channel(channel->center_freq)
- 24) / 2, 5) << 1)
| (1 << 6) | 0x1;
return athchan;
}
/*
* Set channel on RF5110
*/
static int ath5k_hw_rf5110_channel(struct ath5k_hw *ah,
struct net80211_channel *channel)
{
u32 data;
/*
* Set the channel and wait
*/
data = ath5k_hw_rf5110_chan2athchan(channel);
ath5k_hw_reg_write(ah, data, AR5K_RF_BUFFER);
ath5k_hw_reg_write(ah, 0, AR5K_RF_BUFFER_CONTROL_0);
mdelay(1);
return 0;
}
/*
* Convertion needed for 5111
*/
static int ath5k_hw_rf5111_chan2athchan(unsigned int ieee,
struct ath5k_athchan_2ghz *athchan)
{
int channel;
/* Cast this value to catch negative channel numbers (>= -19) */
channel = (int)ieee;
/*
* Map 2GHz IEEE channel to 5GHz Atheros channel
*/
if (channel <= 13) {
athchan->a2_athchan = 115 + channel;
athchan->a2_flags = 0x46;
} else if (channel == 14) {
athchan->a2_athchan = 124;
athchan->a2_flags = 0x44;
} else if (channel >= 15 && channel <= 26) {
athchan->a2_athchan = ((channel - 14) * 4) + 132;
athchan->a2_flags = 0x46;
} else
return -EINVAL;
return 0;
}
/*
* Set channel on 5111
*/
static int ath5k_hw_rf5111_channel(struct ath5k_hw *ah,
struct net80211_channel *channel)
{
struct ath5k_athchan_2ghz ath5k_channel_2ghz;
unsigned int ath5k_channel = ath5k_freq_to_channel(channel->center_freq);
u32 data0, data1, clock;
int ret;
/*
* Set the channel on the RF5111 radio
*/
data0 = data1 = 0;
if (channel->hw_value & CHANNEL_2GHZ) {
/* Map 2GHz channel to 5GHz Atheros channel ID */
ret = ath5k_hw_rf5111_chan2athchan(ath5k_channel,
&ath5k_channel_2ghz);
if (ret)
return ret;
ath5k_channel = ath5k_channel_2ghz.a2_athchan;
data0 = ((ath5k_hw_bitswap(ath5k_channel_2ghz.a2_flags, 8) & 0xff)
<< 5) | (1 << 4);
}
if (ath5k_channel < 145 || !(ath5k_channel & 1)) {
clock = 1;
data1 = ((ath5k_hw_bitswap(ath5k_channel - 24, 8) & 0xff) << 2) |
(clock << 1) | (1 << 10) | 1;
} else {
clock = 0;
data1 = ((ath5k_hw_bitswap((ath5k_channel - 24) / 2, 8) & 0xff)
<< 2) | (clock << 1) | (1 << 10) | 1;
}
ath5k_hw_reg_write(ah, (data1 & 0xff) | ((data0 & 0xff) << 8),
AR5K_RF_BUFFER);
ath5k_hw_reg_write(ah, ((data1 >> 8) & 0xff) | (data0 & 0xff00),
AR5K_RF_BUFFER_CONTROL_3);
return 0;
}
/*
* Set channel on 5112 and newer
*/
static int ath5k_hw_rf5112_channel(struct ath5k_hw *ah,
struct net80211_channel *channel)
{
u32 data, data0, data1, data2;
u16 c;
data = data0 = data1 = data2 = 0;
c = channel->center_freq;
if (c < 4800) {
if (!((c - 2224) % 5)) {
data0 = ((2 * (c - 704)) - 3040) / 10;
data1 = 1;
} else if (!((c - 2192) % 5)) {
data0 = ((2 * (c - 672)) - 3040) / 10;
data1 = 0;
} else
return -EINVAL;
data0 = ath5k_hw_bitswap((data0 << 2) & 0xff, 8);
} else if ((c - (c % 5)) != 2 || c > 5435) {
if (!(c % 20) && c >= 5120) {
data0 = ath5k_hw_bitswap(((c - 4800) / 20 << 2), 8);
data2 = ath5k_hw_bitswap(3, 2);
} else if (!(c % 10)) {
data0 = ath5k_hw_bitswap(((c - 4800) / 10 << 1), 8);
data2 = ath5k_hw_bitswap(2, 2);
} else if (!(c % 5)) {
data0 = ath5k_hw_bitswap((c - 4800) / 5, 8);
data2 = ath5k_hw_bitswap(1, 2);
} else
return -EINVAL;
} else {
data0 = ath5k_hw_bitswap((10 * (c - 2) - 4800) / 25 + 1, 8);
data2 = ath5k_hw_bitswap(0, 2);
}
data = (data0 << 4) | (data1 << 1) | (data2 << 2) | 0x1001;
ath5k_hw_reg_write(ah, data & 0xff, AR5K_RF_BUFFER);
ath5k_hw_reg_write(ah, (data >> 8) & 0x7f, AR5K_RF_BUFFER_CONTROL_5);
return 0;
}
/*
* Set the channel on the RF2425
*/
static int ath5k_hw_rf2425_channel(struct ath5k_hw *ah,
struct net80211_channel *channel)
{
u32 data, data0, data2;
u16 c;
data = data0 = data2 = 0;
c = channel->center_freq;
if (c < 4800) {
data0 = ath5k_hw_bitswap((c - 2272), 8);
data2 = 0;
/* ? 5GHz ? */
} else if ((c - (c % 5)) != 2 || c > 5435) {
if (!(c % 20) && c < 5120)
data0 = ath5k_hw_bitswap(((c - 4800) / 20 << 2), 8);
else if (!(c % 10))
data0 = ath5k_hw_bitswap(((c - 4800) / 10 << 1), 8);
else if (!(c % 5))
data0 = ath5k_hw_bitswap((c - 4800) / 5, 8);
else
return -EINVAL;
data2 = ath5k_hw_bitswap(1, 2);
} else {
data0 = ath5k_hw_bitswap((10 * (c - 2) - 4800) / 25 + 1, 8);
data2 = ath5k_hw_bitswap(0, 2);
}
data = (data0 << 4) | data2 << 2 | 0x1001;
ath5k_hw_reg_write(ah, data & 0xff, AR5K_RF_BUFFER);
ath5k_hw_reg_write(ah, (data >> 8) & 0x7f, AR5K_RF_BUFFER_CONTROL_5);
return 0;
}
/*
* Set a channel on the radio chip
*/
int ath5k_hw_channel(struct ath5k_hw *ah, struct net80211_channel *channel)
{
int ret;
/*
* Check bounds supported by the PHY (we don't care about regultory
* restrictions at this point). Note: hw_value already has the band
* (CHANNEL_2GHZ, or CHANNEL_5GHZ) so we inform ath5k_channel_ok()
* of the band by that */
if (!ath5k_channel_ok(ah, channel->center_freq, channel->hw_value)) {
DBG("ath5k: channel frequency (%d MHz) out of supported "
"range\n", channel->center_freq);
return -EINVAL;
}
/*
* Set the channel and wait
*/
switch (ah->ah_radio) {
case AR5K_RF5110:
ret = ath5k_hw_rf5110_channel(ah, channel);
break;
case AR5K_RF5111:
ret = ath5k_hw_rf5111_channel(ah, channel);
break;
case AR5K_RF2425:
ret = ath5k_hw_rf2425_channel(ah, channel);
break;
default:
ret = ath5k_hw_rf5112_channel(ah, channel);
break;
}
if (ret) {
DBG("ath5k: setting channel failed: %s\n", strerror(ret));
return ret;
}
/* Set JAPAN setting for channel 14 */
if (channel->center_freq == 2484) {
AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_CCKTXCTL,
AR5K_PHY_CCKTXCTL_JAPAN);
} else {
AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_CCKTXCTL,
AR5K_PHY_CCKTXCTL_WORLD);
}
ah->ah_current_channel = channel;
ah->ah_turbo = (channel->hw_value == CHANNEL_T ? 1 : 0);
return 0;
}
/*****************\
PHY calibration
\*****************/
/**
* ath5k_hw_noise_floor_calibration - perform PHY noise floor calibration
*
* @ah: struct ath5k_hw pointer we are operating on
* @freq: the channel frequency, just used for error logging
*
* This function performs a noise floor calibration of the PHY and waits for
* it to complete. Then the noise floor value is compared to some maximum
* noise floor we consider valid.
*
* Note that this is different from what the madwifi HAL does: it reads the
* noise floor and afterwards initiates the calibration. Since the noise floor
* calibration can take some time to finish, depending on the current channel
* use, that avoids the occasional timeout warnings we are seeing now.
*
* See the following link for an Atheros patent on noise floor calibration:
* http://patft.uspto.gov/netacgi/nph-Parser?Sect1=PTO1&Sect2=HITOFF&d=PALL \
* &p=1&u=%2Fnetahtml%2FPTO%2Fsrchnum.htm&r=1&f=G&l=50&s1=7245893.PN.&OS=PN/7
*
* XXX: Since during noise floor calibration antennas are detached according to
* the patent, we should stop tx queues here.
*/
int
ath5k_hw_noise_floor_calibration(struct ath5k_hw *ah, short freq)
{
int ret;
unsigned int i;
s32 noise_floor;
/*
* Enable noise floor calibration
*/
AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL,
AR5K_PHY_AGCCTL_NF);
ret = ath5k_hw_register_timeout(ah, AR5K_PHY_AGCCTL,
AR5K_PHY_AGCCTL_NF, 0, 0);
if (ret) {
DBG("ath5k: noise floor calibration timeout (%d MHz)\n", freq);
return -EAGAIN;
}
/* Wait until the noise floor is calibrated and read the value */
for (i = 20; i > 0; i--) {
mdelay(1);
noise_floor = ath5k_hw_reg_read(ah, AR5K_PHY_NF);
noise_floor = AR5K_PHY_NF_RVAL(noise_floor);
if (noise_floor & AR5K_PHY_NF_ACTIVE) {
noise_floor = AR5K_PHY_NF_AVAL(noise_floor);
if (noise_floor <= AR5K_TUNE_NOISE_FLOOR)
break;
}
}
DBG2("ath5k: noise floor %d\n", noise_floor);
if (noise_floor > AR5K_TUNE_NOISE_FLOOR) {
DBG("ath5k: noise floor calibration failed (%d MHz)\n", freq);
return -EAGAIN;
}
ah->ah_noise_floor = noise_floor;
return 0;
}
/*
* Perform a PHY calibration on RF5110
* -Fix BPSK/QAM Constellation (I/Q correction)
* -Calculate Noise Floor
*/
static int ath5k_hw_rf5110_calibrate(struct ath5k_hw *ah,
struct net80211_channel *channel)
{
u32 phy_sig, phy_agc, phy_sat, beacon;
int ret;
/*
* Disable beacons and RX/TX queues, wait
*/
AR5K_REG_ENABLE_BITS(ah, AR5K_DIAG_SW_5210,
AR5K_DIAG_SW_DIS_TX | AR5K_DIAG_SW_DIS_RX_5210);
beacon = ath5k_hw_reg_read(ah, AR5K_BEACON_5210);
ath5k_hw_reg_write(ah, beacon & ~AR5K_BEACON_ENABLE, AR5K_BEACON_5210);
mdelay(2);
/*
* Set the channel (with AGC turned off)
*/
AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGC, AR5K_PHY_AGC_DISABLE);
udelay(10);
ret = ath5k_hw_channel(ah, channel);
/*
* Activate PHY and wait
*/
ath5k_hw_reg_write(ah, AR5K_PHY_ACT_ENABLE, AR5K_PHY_ACT);
mdelay(1);
AR5K_REG_DISABLE_BITS(ah, AR5K_PHY_AGC, AR5K_PHY_AGC_DISABLE);
if (ret)
return ret;
/*
* Calibrate the radio chip
*/
/* Remember normal state */
phy_sig = ath5k_hw_reg_read(ah, AR5K_PHY_SIG);
phy_agc = ath5k_hw_reg_read(ah, AR5K_PHY_AGCCOARSE);
phy_sat = ath5k_hw_reg_read(ah, AR5K_PHY_ADCSAT);
/* Update radio registers */
ath5k_hw_reg_write(ah, (phy_sig & ~(AR5K_PHY_SIG_FIRPWR)) |
AR5K_REG_SM(-1, AR5K_PHY_SIG_FIRPWR), AR5K_PHY_SIG);
ath5k_hw_reg_write(ah, (phy_agc & ~(AR5K_PHY_AGCCOARSE_HI |
AR5K_PHY_AGCCOARSE_LO)) |
AR5K_REG_SM(-1, AR5K_PHY_AGCCOARSE_HI) |
AR5K_REG_SM(-127, AR5K_PHY_AGCCOARSE_LO), AR5K_PHY_AGCCOARSE);
ath5k_hw_reg_write(ah, (phy_sat & ~(AR5K_PHY_ADCSAT_ICNT |
AR5K_PHY_ADCSAT_THR)) |
AR5K_REG_SM(2, AR5K_PHY_ADCSAT_ICNT) |
AR5K_REG_SM(12, AR5K_PHY_ADCSAT_THR), AR5K_PHY_ADCSAT);
udelay(20);
AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGC, AR5K_PHY_AGC_DISABLE);
udelay(10);
ath5k_hw_reg_write(ah, AR5K_PHY_RFSTG_DISABLE, AR5K_PHY_RFSTG);
AR5K_REG_DISABLE_BITS(ah, AR5K_PHY_AGC, AR5K_PHY_AGC_DISABLE);
mdelay(1);
/*
* Enable calibration and wait until completion
*/
AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL, AR5K_PHY_AGCCTL_CAL);
ret = ath5k_hw_register_timeout(ah, AR5K_PHY_AGCCTL,
AR5K_PHY_AGCCTL_CAL, 0, 0);
/* Reset to normal state */
ath5k_hw_reg_write(ah, phy_sig, AR5K_PHY_SIG);
ath5k_hw_reg_write(ah, phy_agc, AR5K_PHY_AGCCOARSE);
ath5k_hw_reg_write(ah, phy_sat, AR5K_PHY_ADCSAT);
if (ret) {
DBG("ath5k: calibration timeout (%d MHz)\n",
channel->center_freq);
return ret;
}
ath5k_hw_noise_floor_calibration(ah, channel->center_freq);
/*
* Re-enable RX/TX and beacons
*/
AR5K_REG_DISABLE_BITS(ah, AR5K_DIAG_SW_5210,
AR5K_DIAG_SW_DIS_TX | AR5K_DIAG_SW_DIS_RX_5210);
ath5k_hw_reg_write(ah, beacon, AR5K_BEACON_5210);
return 0;
}
/*
* Perform a PHY calibration on RF5111/5112 and newer chips
*/
static int ath5k_hw_rf511x_calibrate(struct ath5k_hw *ah,
struct net80211_channel *channel)
{
u32 i_pwr, q_pwr;
s32 iq_corr, i_coff, i_coffd, q_coff, q_coffd;
int i;
if (!ah->ah_calibration ||
ath5k_hw_reg_read(ah, AR5K_PHY_IQ) & AR5K_PHY_IQ_RUN)
goto done;
/* Calibration has finished, get the results and re-run */
for (i = 0; i <= 10; i++) {
iq_corr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_CORR);
i_pwr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_PWR_I);
q_pwr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_PWR_Q);
}
i_coffd = ((i_pwr >> 1) + (q_pwr >> 1)) >> 7;
q_coffd = q_pwr >> 7;
/* No correction */
if (i_coffd == 0 || q_coffd == 0)
goto done;
i_coff = ((-iq_corr) / i_coffd) & 0x3f;
/* Boundary check */
if (i_coff > 31)
i_coff = 31;
if (i_coff < -32)
i_coff = -32;
q_coff = (((s32)i_pwr / q_coffd) - 128) & 0x1f;
/* Boundary check */
if (q_coff > 15)
q_coff = 15;
if (q_coff < -16)
q_coff = -16;
/* Commit new I/Q value */
AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ, AR5K_PHY_IQ_CORR_ENABLE |
((u32)q_coff) | ((u32)i_coff << AR5K_PHY_IQ_CORR_Q_I_COFF_S));
/* Re-enable calibration -if we don't we'll commit
* the same values again and again */
AR5K_REG_WRITE_BITS(ah, AR5K_PHY_IQ,
AR5K_PHY_IQ_CAL_NUM_LOG_MAX, 15);
AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ, AR5K_PHY_IQ_RUN);
done:
/* TODO: Separate noise floor calibration from I/Q calibration
* since noise floor calibration interrupts rx path while I/Q
* calibration doesn't. We don't need to run noise floor calibration
* as often as I/Q calibration.*/
ath5k_hw_noise_floor_calibration(ah, channel->center_freq);
/* Initiate a gain_F calibration */
ath5k_hw_request_rfgain_probe(ah);
return 0;
}
/*
* Perform a PHY calibration
*/
int ath5k_hw_phy_calibrate(struct ath5k_hw *ah,
struct net80211_channel *channel)
{
int ret;
if (ah->ah_radio == AR5K_RF5110)
ret = ath5k_hw_rf5110_calibrate(ah, channel);
else
ret = ath5k_hw_rf511x_calibrate(ah, channel);
return ret;
}
int ath5k_hw_phy_disable(struct ath5k_hw *ah)
{
ath5k_hw_reg_write(ah, AR5K_PHY_ACT_DISABLE, AR5K_PHY_ACT);
return 0;
}
/********************\
Misc PHY functions
\********************/
/*
* Get the PHY Chip revision
*/
u16 ath5k_hw_radio_revision(struct ath5k_hw *ah, unsigned int chan)
{
unsigned int i;
u32 srev;
u16 ret;
/*
* Set the radio chip access register
*/
switch (chan) {
case CHANNEL_2GHZ:
ath5k_hw_reg_write(ah, AR5K_PHY_SHIFT_2GHZ, AR5K_PHY(0));
break;
case CHANNEL_5GHZ:
ath5k_hw_reg_write(ah, AR5K_PHY_SHIFT_5GHZ, AR5K_PHY(0));
break;
default:
return 0;
}
mdelay(2);
/* ...wait until PHY is ready and read the selected radio revision */
ath5k_hw_reg_write(ah, 0x00001c16, AR5K_PHY(0x34));
for (i = 0; i < 8; i++)
ath5k_hw_reg_write(ah, 0x00010000, AR5K_PHY(0x20));
if (ah->ah_version == AR5K_AR5210) {
srev = ath5k_hw_reg_read(ah, AR5K_PHY(256) >> 28) & 0xf;
ret = (u16)ath5k_hw_bitswap(srev, 4) + 1;
} else {
srev = (ath5k_hw_reg_read(ah, AR5K_PHY(0x100)) >> 24) & 0xff;
ret = (u16)ath5k_hw_bitswap(((srev & 0xf0) >> 4) |
((srev & 0x0f) << 4), 8);
}
/* Reset to the 5GHz mode */
ath5k_hw_reg_write(ah, AR5K_PHY_SHIFT_5GHZ, AR5K_PHY(0));
return ret;
}
void /*TODO:Boundary check*/
ath5k_hw_set_def_antenna(struct ath5k_hw *ah, unsigned int ant)
{
if (ah->ah_version != AR5K_AR5210)
ath5k_hw_reg_write(ah, ant, AR5K_DEFAULT_ANTENNA);
}
unsigned int ath5k_hw_get_def_antenna(struct ath5k_hw *ah)
{
if (ah->ah_version != AR5K_AR5210)
return ath5k_hw_reg_read(ah, AR5K_DEFAULT_ANTENNA);
return 0; /*XXX: What do we return for 5210 ?*/
}
/****************\
* TX power setup *
\****************/
/*
* Helper functions
*/
/*
* Do linear interpolation between two given (x, y) points
*/
static s16
ath5k_get_interpolated_value(s16 target, s16 x_left, s16 x_right,
s16 y_left, s16 y_right)
{
s16 ratio, result;
/* Avoid divide by zero and skip interpolation
* if we have the same point */
if ((x_left == x_right) || (y_left == y_right))
return y_left;
/*
* Since we use ints and not fps, we need to scale up in
* order to get a sane ratio value (or else we 'll eg. get
* always 1 instead of 1.25, 1.75 etc). We scale up by 100
* to have some accuracy both for 0.5 and 0.25 steps.
*/
ratio = ((100 * y_right - 100 * y_left)/(x_right - x_left));
/* Now scale down to be in range */
result = y_left + (ratio * (target - x_left) / 100);
return result;
}
/*
* Find vertical boundary (min pwr) for the linear PCDAC curve.
*
* Since we have the top of the curve and we draw the line below
* until we reach 1 (1 pcdac step) we need to know which point
* (x value) that is so that we don't go below y axis and have negative
* pcdac values when creating the curve, or fill the table with zeroes.
*/
static s16
ath5k_get_linear_pcdac_min(const u8 *stepL, const u8 *stepR,
const s16 *pwrL, const s16 *pwrR)
{
s8 tmp;
s16 min_pwrL, min_pwrR;
s16 pwr_i;
if (pwrL[0] == pwrL[1])
min_pwrL = pwrL[0];
else {
pwr_i = pwrL[0];
do {
pwr_i--;
tmp = (s8) ath5k_get_interpolated_value(pwr_i,
pwrL[0], pwrL[1],
stepL[0], stepL[1]);
} while (tmp > 1);
min_pwrL = pwr_i;
}
if (pwrR[0] == pwrR[1])
min_pwrR = pwrR[0];
else {
pwr_i = pwrR[0];
do {
pwr_i--;
tmp = (s8) ath5k_get_interpolated_value(pwr_i,
pwrR[0], pwrR[1],
stepR[0], stepR[1]);
} while (tmp > 1);
min_pwrR = pwr_i;
}
/* Keep the right boundary so that it works for both curves */
return max(min_pwrL, min_pwrR);
}
/*
* Interpolate (pwr,vpd) points to create a Power to PDADC or a
* Power to PCDAC curve.
*
* Each curve has power on x axis (in 0.5dB units) and PCDAC/PDADC
* steps (offsets) on y axis. Power can go up to 31.5dB and max
* PCDAC/PDADC step for each curve is 64 but we can write more than
* one curves on hw so we can go up to 128 (which is the max step we
* can write on the final table).
*
* We write y values (PCDAC/PDADC steps) on hw.
*/
static void
ath5k_create_power_curve(s16 pmin, s16 pmax,
const s16 *pwr, const u8 *vpd,
u8 num_points,
u8 *vpd_table, u8 type)
{
u8 idx[2] = { 0, 1 };
s16 pwr_i = 2*pmin;
int i;
if (num_points < 2)
return;
/* We want the whole line, so adjust boundaries
* to cover the entire power range. Note that
* power values are already 0.25dB so no need
* to multiply pwr_i by 2 */
if (type == AR5K_PWRTABLE_LINEAR_PCDAC) {
pwr_i = pmin;
pmin = 0;
pmax = 63;
}
/* Find surrounding turning points (TPs)
* and interpolate between them */
for (i = 0; (i <= (u16) (pmax - pmin)) &&
(i < AR5K_EEPROM_POWER_TABLE_SIZE); i++) {
/* We passed the right TP, move to the next set of TPs
* if we pass the last TP, extrapolate above using the last
* two TPs for ratio */
if ((pwr_i > pwr[idx[1]]) && (idx[1] < num_points - 1)) {
idx[0]++;
idx[1]++;
}
vpd_table[i] = (u8) ath5k_get_interpolated_value(pwr_i,
pwr[idx[0]], pwr[idx[1]],
vpd[idx[0]], vpd[idx[1]]);
/* Increase by 0.5dB
* (0.25 dB units) */
pwr_i += 2;
}
}
/*
* Get the surrounding per-channel power calibration piers
* for a given frequency so that we can interpolate between
* them and come up with an apropriate dataset for our current
* channel.
*/
static void
ath5k_get_chan_pcal_surrounding_piers(struct ath5k_hw *ah,
struct net80211_channel *channel,
struct ath5k_chan_pcal_info **pcinfo_l,
struct ath5k_chan_pcal_info **pcinfo_r)
{
struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom;
struct ath5k_chan_pcal_info *pcinfo;
u8 idx_l, idx_r;
u8 mode, max, i;
u32 target = channel->center_freq;
idx_l = 0;
idx_r = 0;
if (!(channel->hw_value & CHANNEL_OFDM)) {
pcinfo = ee->ee_pwr_cal_b;
mode = AR5K_EEPROM_MODE_11B;
} else if (channel->hw_value & CHANNEL_2GHZ) {
pcinfo = ee->ee_pwr_cal_g;
mode = AR5K_EEPROM_MODE_11G;
} else {
pcinfo = ee->ee_pwr_cal_a;
mode = AR5K_EEPROM_MODE_11A;
}
max = ee->ee_n_piers[mode] - 1;
/* Frequency is below our calibrated
* range. Use the lowest power curve
* we have */
if (target < pcinfo[0].freq) {
idx_l = idx_r = 0;
goto done;
}
/* Frequency is above our calibrated
* range. Use the highest power curve
* we have */
if (target > pcinfo[max].freq) {
idx_l = idx_r = max;
goto done;
}
/* Frequency is inside our calibrated
* channel range. Pick the surrounding
* calibration piers so that we can
* interpolate */
for (i = 0; i <= max; i++) {
/* Frequency matches one of our calibration
* piers, no need to interpolate, just use
* that calibration pier */
if (pcinfo[i].freq == target) {
idx_l = idx_r = i;
goto done;
}
/* We found a calibration pier that's above
* frequency, use this pier and the previous
* one to interpolate */
if (target < pcinfo[i].freq) {
idx_r = i;
idx_l = idx_r - 1;
goto done;
}
}
done:
*pcinfo_l = &pcinfo[idx_l];
*pcinfo_r = &pcinfo[idx_r];
return;
}
/*
* Get the surrounding per-rate power calibration data
* for a given frequency and interpolate between power
* values to set max target power supported by hw for
* each rate.
*/
static void
ath5k_get_rate_pcal_data(struct ath5k_hw *ah,
struct net80211_channel *channel,
struct ath5k_rate_pcal_info *rates)
{
struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom;
struct ath5k_rate_pcal_info *rpinfo;
u8 idx_l, idx_r;
u8 mode, max, i;
u32 target = channel->center_freq;
idx_l = 0;
idx_r = 0;
if (!(channel->hw_value & CHANNEL_OFDM)) {
rpinfo = ee->ee_rate_tpwr_b;
mode = AR5K_EEPROM_MODE_11B;
} else if (channel->hw_value & CHANNEL_2GHZ) {
rpinfo = ee->ee_rate_tpwr_g;
mode = AR5K_EEPROM_MODE_11G;
} else {
rpinfo = ee->ee_rate_tpwr_a;
mode = AR5K_EEPROM_MODE_11A;
}
max = ee->ee_rate_target_pwr_num[mode] - 1;
/* Get the surrounding calibration
* piers - same as above */
if (target < rpinfo[0].freq) {
idx_l = idx_r = 0;
goto done;
}
if (target > rpinfo[max].freq) {
idx_l = idx_r = max;
goto done;
}
for (i = 0; i <= max; i++) {
if (rpinfo[i].freq == target) {
idx_l = idx_r = i;
goto done;
}
if (target < rpinfo[i].freq) {
idx_r = i;
idx_l = idx_r - 1;
goto done;
}
}
done:
/* Now interpolate power value, based on the frequency */
rates->freq = target;
rates->target_power_6to24 =
ath5k_get_interpolated_value(target, rpinfo[idx_l].freq,
rpinfo[idx_r].freq,
rpinfo[idx_l].target_power_6to24,
rpinfo[idx_r].target_power_6to24);
rates->target_power_36 =
ath5k_get_interpolated_value(target, rpinfo[idx_l].freq,
rpinfo[idx_r].freq,
rpinfo[idx_l].target_power_36,
rpinfo[idx_r].target_power_36);
rates->target_power_48 =
ath5k_get_interpolated_value(target, rpinfo[idx_l].freq,
rpinfo[idx_r].freq,
rpinfo[idx_l].target_power_48,
rpinfo[idx_r].target_power_48);
rates->target_power_54 =
ath5k_get_interpolated_value(target, rpinfo[idx_l].freq,
rpinfo[idx_r].freq,
rpinfo[idx_l].target_power_54,
rpinfo[idx_r].target_power_54);
}
/*
* Get the max edge power for this channel if
* we have such data from EEPROM's Conformance Test
* Limits (CTL), and limit max power if needed.
*
* FIXME: Only works for world regulatory domains
*/
static void
ath5k_get_max_ctl_power(struct ath5k_hw *ah,
struct net80211_channel *channel)
{
struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom;
struct ath5k_edge_power *rep = ee->ee_ctl_pwr;
u8 *ctl_val = ee->ee_ctl;
s16 max_chan_pwr = ah->ah_txpower.txp_max_pwr / 4;
s16 edge_pwr = 0;
u8 rep_idx;
u8 i, ctl_mode;
u8 ctl_idx = 0xFF;
u32 target = channel->center_freq;
/* Find out a CTL for our mode that's not mapped
* on a specific reg domain.
*
* TODO: Map our current reg domain to one of the 3 available
* reg domain ids so that we can support more CTLs. */
switch (channel->hw_value & CHANNEL_MODES) {
case CHANNEL_A:
ctl_mode = AR5K_CTL_11A | AR5K_CTL_NO_REGDOMAIN;
break;
case CHANNEL_G:
ctl_mode = AR5K_CTL_11G | AR5K_CTL_NO_REGDOMAIN;
break;
case CHANNEL_B:
ctl_mode = AR5K_CTL_11B | AR5K_CTL_NO_REGDOMAIN;
break;
case CHANNEL_T:
ctl_mode = AR5K_CTL_TURBO | AR5K_CTL_NO_REGDOMAIN;
break;
case CHANNEL_TG:
ctl_mode = AR5K_CTL_TURBOG | AR5K_CTL_NO_REGDOMAIN;
break;
case CHANNEL_XR:
/* Fall through */
default:
return;
}
for (i = 0; i < ee->ee_ctls; i++) {
if (ctl_val[i] == ctl_mode) {
ctl_idx = i;
break;
}
}
/* If we have a CTL dataset available grab it and find the
* edge power for our frequency */
if (ctl_idx == 0xFF)
return;
/* Edge powers are sorted by frequency from lower
* to higher. Each CTL corresponds to 8 edge power
* measurements. */
rep_idx = ctl_idx * AR5K_EEPROM_N_EDGES;
/* Don't do boundaries check because we
* might have more that one bands defined
* for this mode */
/* Get the edge power that's closer to our
* frequency */
for (i = 0; i < AR5K_EEPROM_N_EDGES; i++) {
rep_idx += i;
if (target <= rep[rep_idx].freq)
edge_pwr = (s16) rep[rep_idx].edge;
}
if (edge_pwr) {
ah->ah_txpower.txp_max_pwr = 4*min(edge_pwr, max_chan_pwr);
}
}
/*
* Power to PCDAC table functions
*/
/*
* Fill Power to PCDAC table on RF5111
*
* No further processing is needed for RF5111, the only thing we have to
* do is fill the values below and above calibration range since eeprom data
* may not cover the entire PCDAC table.
*/
static void
ath5k_fill_pwr_to_pcdac_table(struct ath5k_hw *ah, s16* table_min,
s16 *table_max)
{
u8 *pcdac_out = ah->ah_txpower.txp_pd_table;
u8 *pcdac_tmp = ah->ah_txpower.tmpL[0];
u8 pcdac_0, pcdac_n, pcdac_i, pwr_idx, i;
s16 min_pwr, max_pwr;
/* Get table boundaries */
min_pwr = table_min[0];
pcdac_0 = pcdac_tmp[0];
max_pwr = table_max[0];
pcdac_n = pcdac_tmp[table_max[0] - table_min[0]];
/* Extrapolate below minimum using pcdac_0 */
pcdac_i = 0;
for (i = 0; i < min_pwr; i++)
pcdac_out[pcdac_i++] = pcdac_0;
/* Copy values from pcdac_tmp */
pwr_idx = min_pwr;
for (i = 0 ; pwr_idx <= max_pwr &&
pcdac_i < AR5K_EEPROM_POWER_TABLE_SIZE; i++) {
pcdac_out[pcdac_i++] = pcdac_tmp[i];
pwr_idx++;
}
/* Extrapolate above maximum */
while (pcdac_i < AR5K_EEPROM_POWER_TABLE_SIZE)
pcdac_out[pcdac_i++] = pcdac_n;
}
/*
* Combine available XPD Curves and fill Linear Power to PCDAC table
* on RF5112
*
* RFX112 can have up to 2 curves (one for low txpower range and one for
* higher txpower range). We need to put them both on pcdac_out and place
* them in the correct location. In case we only have one curve available
* just fit it on pcdac_out (it's supposed to cover the entire range of
* available pwr levels since it's always the higher power curve). Extrapolate
* below and above final table if needed.
*/
static void
ath5k_combine_linear_pcdac_curves(struct ath5k_hw *ah, s16* table_min,
s16 *table_max, u8 pdcurves)
{
u8 *pcdac_out = ah->ah_txpower.txp_pd_table;
u8 *pcdac_low_pwr;
u8 *pcdac_high_pwr;
u8 *pcdac_tmp;
u8 pwr;
s16 max_pwr_idx;
s16 min_pwr_idx;
s16 mid_pwr_idx = 0;
/* Edge flag turs on the 7nth bit on the PCDAC
* to delcare the higher power curve (force values
* to be greater than 64). If we only have one curve
* we don't need to set this, if we have 2 curves and
* fill the table backwards this can also be used to
* switch from higher power curve to lower power curve */
u8 edge_flag;
int i;
/* When we have only one curve available
* that's the higher power curve. If we have
* two curves the first is the high power curve
* and the next is the low power curve. */
if (pdcurves > 1) {
pcdac_low_pwr = ah->ah_txpower.tmpL[1];
pcdac_high_pwr = ah->ah_txpower.tmpL[0];
mid_pwr_idx = table_max[1] - table_min[1] - 1;
max_pwr_idx = (table_max[0] - table_min[0]) / 2;
/* If table size goes beyond 31.5dB, keep the
* upper 31.5dB range when setting tx power.
* Note: 126 = 31.5 dB in quarter dB steps */
if (table_max[0] - table_min[1] > 126)
min_pwr_idx = table_max[0] - 126;
else
min_pwr_idx = table_min[1];
/* Since we fill table backwards
* start from high power curve */
pcdac_tmp = pcdac_high_pwr;
edge_flag = 0x40;
} else {
pcdac_low_pwr = ah->ah_txpower.tmpL[1]; /* Zeroed */
pcdac_high_pwr = ah->ah_txpower.tmpL[0];
min_pwr_idx = table_min[0];
max_pwr_idx = (table_max[0] - table_min[0]) / 2;
pcdac_tmp = pcdac_high_pwr;
edge_flag = 0;
}
/* This is used when setting tx power*/
ah->ah_txpower.txp_min_idx = min_pwr_idx/2;
/* Fill Power to PCDAC table backwards */
pwr = max_pwr_idx;
for (i = 63; i >= 0; i--) {
/* Entering lower power range, reset
* edge flag and set pcdac_tmp to lower
* power curve.*/
if (edge_flag == 0x40 &&
(2*pwr <= (table_max[1] - table_min[0]) || pwr == 0)) {
edge_flag = 0x00;
pcdac_tmp = pcdac_low_pwr;
pwr = mid_pwr_idx/2;
}
/* Don't go below 1, extrapolate below if we have
* already swithced to the lower power curve -or
* we only have one curve and edge_flag is zero
* anyway */
if (pcdac_tmp[pwr] < 1 && (edge_flag == 0x00)) {
while (i >= 0) {
pcdac_out[i] = pcdac_out[i + 1];
i--;
}
break;
}
pcdac_out[i] = pcdac_tmp[pwr] | edge_flag;
/* Extrapolate above if pcdac is greater than
* 126 -this can happen because we OR pcdac_out
* value with edge_flag on high power curve */
if (pcdac_out[i] > 126)
pcdac_out[i] = 126;
/* Decrease by a 0.5dB step */
pwr--;
}
}
/* Write PCDAC values on hw */
static void
ath5k_setup_pcdac_table(struct ath5k_hw *ah)
{
u8 *pcdac_out = ah->ah_txpower.txp_pd_table;
int i;
/*
* Write TX power values
*/
for (i = 0; i < (AR5K_EEPROM_POWER_TABLE_SIZE / 2); i++) {
ath5k_hw_reg_write(ah,
(((pcdac_out[2*i + 0] << 8 | 0xff) & 0xffff) << 0) |
(((pcdac_out[2*i + 1] << 8 | 0xff) & 0xffff) << 16),
AR5K_PHY_PCDAC_TXPOWER(i));
}
}
/*
* Power to PDADC table functions
*/
/*
* Set the gain boundaries and create final Power to PDADC table
*
* We can have up to 4 pd curves, we need to do a simmilar process
* as we do for RF5112. This time we don't have an edge_flag but we
* set the gain boundaries on a separate register.
*/
static void
ath5k_combine_pwr_to_pdadc_curves(struct ath5k_hw *ah,
s16 *pwr_min, s16 *pwr_max, u8 pdcurves)
{
u8 gain_boundaries[AR5K_EEPROM_N_PD_GAINS];
u8 *pdadc_out = ah->ah_txpower.txp_pd_table;
u8 *pdadc_tmp;
s16 pdadc_0;
u8 pdadc_i, pdadc_n, pwr_step, pdg, max_idx, table_size;
u8 pd_gain_overlap;
/* Note: Register value is initialized on initvals
* there is no feedback from hw.
* XXX: What about pd_gain_overlap from EEPROM ? */
pd_gain_overlap = (u8) ath5k_hw_reg_read(ah, AR5K_PHY_TPC_RG5) &
AR5K_PHY_TPC_RG5_PD_GAIN_OVERLAP;
/* Create final PDADC table */
for (pdg = 0, pdadc_i = 0; pdg < pdcurves; pdg++) {
pdadc_tmp = ah->ah_txpower.tmpL[pdg];
if (pdg == pdcurves - 1)
/* 2 dB boundary stretch for last
* (higher power) curve */
gain_boundaries[pdg] = pwr_max[pdg] + 4;
else
/* Set gain boundary in the middle
* between this curve and the next one */
gain_boundaries[pdg] =
(pwr_max[pdg] + pwr_min[pdg + 1]) / 2;
/* Sanity check in case our 2 db stretch got out of
* range. */
if (gain_boundaries[pdg] > AR5K_TUNE_MAX_TXPOWER)
gain_boundaries[pdg] = AR5K_TUNE_MAX_TXPOWER;
/* For the first curve (lower power)
* start from 0 dB */
if (pdg == 0)
pdadc_0 = 0;
else
/* For the other curves use the gain overlap */
pdadc_0 = (gain_boundaries[pdg - 1] - pwr_min[pdg]) -
pd_gain_overlap;
/* Force each power step to be at least 0.5 dB */
if ((pdadc_tmp[1] - pdadc_tmp[0]) > 1)
pwr_step = pdadc_tmp[1] - pdadc_tmp[0];
else
pwr_step = 1;
/* If pdadc_0 is negative, we need to extrapolate
* below this pdgain by a number of pwr_steps */
while ((pdadc_0 < 0) && (pdadc_i < 128)) {
s16 tmp = pdadc_tmp[0] + pdadc_0 * pwr_step;
pdadc_out[pdadc_i++] = (tmp < 0) ? 0 : (u8) tmp;
pdadc_0++;
}
/* Set last pwr level, using gain boundaries */
pdadc_n = gain_boundaries[pdg] + pd_gain_overlap - pwr_min[pdg];
/* Limit it to be inside pwr range */
table_size = pwr_max[pdg] - pwr_min[pdg];
max_idx = (pdadc_n < table_size) ? pdadc_n : table_size;
/* Fill pdadc_out table */
while (pdadc_0 < max_idx)
pdadc_out[pdadc_i++] = pdadc_tmp[pdadc_0++];
/* Need to extrapolate above this pdgain? */
if (pdadc_n <= max_idx)
continue;
/* Force each power step to be at least 0.5 dB */
if ((pdadc_tmp[table_size - 1] - pdadc_tmp[table_size - 2]) > 1)
pwr_step = pdadc_tmp[table_size - 1] -
pdadc_tmp[table_size - 2];
else
pwr_step = 1;
/* Extrapolate above */
while ((pdadc_0 < (s16) pdadc_n) &&
(pdadc_i < AR5K_EEPROM_POWER_TABLE_SIZE * 2)) {
s16 tmp = pdadc_tmp[table_size - 1] +
(pdadc_0 - max_idx) * pwr_step;
pdadc_out[pdadc_i++] = (tmp > 127) ? 127 : (u8) tmp;
pdadc_0++;
}
}
while (pdg < AR5K_EEPROM_N_PD_GAINS) {
gain_boundaries[pdg] = gain_boundaries[pdg - 1];
pdg++;
}
while (pdadc_i < AR5K_EEPROM_POWER_TABLE_SIZE * 2) {
pdadc_out[pdadc_i] = pdadc_out[pdadc_i - 1];
pdadc_i++;
}
/* Set gain boundaries */
ath5k_hw_reg_write(ah,
AR5K_REG_SM(pd_gain_overlap,
AR5K_PHY_TPC_RG5_PD_GAIN_OVERLAP) |
AR5K_REG_SM(gain_boundaries[0],
AR5K_PHY_TPC_RG5_PD_GAIN_BOUNDARY_1) |
AR5K_REG_SM(gain_boundaries[1],
AR5K_PHY_TPC_RG5_PD_GAIN_BOUNDARY_2) |
AR5K_REG_SM(gain_boundaries[2],
AR5K_PHY_TPC_RG5_PD_GAIN_BOUNDARY_3) |
AR5K_REG_SM(gain_boundaries[3],
AR5K_PHY_TPC_RG5_PD_GAIN_BOUNDARY_4),
AR5K_PHY_TPC_RG5);
/* Used for setting rate power table */
ah->ah_txpower.txp_min_idx = pwr_min[0];
}
/* Write PDADC values on hw */
static void
ath5k_setup_pwr_to_pdadc_table(struct ath5k_hw *ah,
u8 pdcurves, u8 *pdg_to_idx)
{
u8 *pdadc_out = ah->ah_txpower.txp_pd_table;
u32 reg;
u8 i;
/* Select the right pdgain curves */
/* Clear current settings */
reg = ath5k_hw_reg_read(ah, AR5K_PHY_TPC_RG1);
reg &= ~(AR5K_PHY_TPC_RG1_PDGAIN_1 |
AR5K_PHY_TPC_RG1_PDGAIN_2 |
AR5K_PHY_TPC_RG1_PDGAIN_3 |
AR5K_PHY_TPC_RG1_NUM_PD_GAIN);
/*
* Use pd_gains curve from eeprom
*
* This overrides the default setting from initvals
* in case some vendors (e.g. Zcomax) don't use the default
* curves. If we don't honor their settings we 'll get a
* 5dB (1 * gain overlap ?) drop.
*/
reg |= AR5K_REG_SM(pdcurves, AR5K_PHY_TPC_RG1_NUM_PD_GAIN);
switch (pdcurves) {
case 3:
reg |= AR5K_REG_SM(pdg_to_idx[2], AR5K_PHY_TPC_RG1_PDGAIN_3);
/* Fall through */
case 2:
reg |= AR5K_REG_SM(pdg_to_idx[1], AR5K_PHY_TPC_RG1_PDGAIN_2);
/* Fall through */
case 1:
reg |= AR5K_REG_SM(pdg_to_idx[0], AR5K_PHY_TPC_RG1_PDGAIN_1);
break;
}
ath5k_hw_reg_write(ah, reg, AR5K_PHY_TPC_RG1);
/*
* Write TX power values
*/
for (i = 0; i < (AR5K_EEPROM_POWER_TABLE_SIZE / 2); i++) {
ath5k_hw_reg_write(ah,
((pdadc_out[4*i + 0] & 0xff) << 0) |
((pdadc_out[4*i + 1] & 0xff) << 8) |
((pdadc_out[4*i + 2] & 0xff) << 16) |
((pdadc_out[4*i + 3] & 0xff) << 24),
AR5K_PHY_PDADC_TXPOWER(i));
}
}
/*
* Common code for PCDAC/PDADC tables
*/
/*
* This is the main function that uses all of the above
* to set PCDAC/PDADC table on hw for the current channel.
* This table is used for tx power calibration on the basband,
* without it we get weird tx power levels and in some cases
* distorted spectral mask
*/
static int
ath5k_setup_channel_powertable(struct ath5k_hw *ah,
struct net80211_channel *channel,
u8 ee_mode, u8 type)
{
struct ath5k_pdgain_info *pdg_L, *pdg_R;
struct ath5k_chan_pcal_info *pcinfo_L;
struct ath5k_chan_pcal_info *pcinfo_R;
struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom;
u8 *pdg_curve_to_idx = ee->ee_pdc_to_idx[ee_mode];
s16 table_min[AR5K_EEPROM_N_PD_GAINS];
s16 table_max[AR5K_EEPROM_N_PD_GAINS];
u8 *tmpL;
u8 *tmpR;
u32 target = channel->center_freq;
int pdg, i;
/* Get surounding freq piers for this channel */
ath5k_get_chan_pcal_surrounding_piers(ah, channel,
&pcinfo_L,
&pcinfo_R);
/* Loop over pd gain curves on
* surounding freq piers by index */
for (pdg = 0; pdg < ee->ee_pd_gains[ee_mode]; pdg++) {
/* Fill curves in reverse order
* from lower power (max gain)
* to higher power. Use curve -> idx
* backmaping we did on eeprom init */
u8 idx = pdg_curve_to_idx[pdg];
/* Grab the needed curves by index */
pdg_L = &pcinfo_L->pd_curves[idx];
pdg_R = &pcinfo_R->pd_curves[idx];
/* Initialize the temp tables */
tmpL = ah->ah_txpower.tmpL[pdg];
tmpR = ah->ah_txpower.tmpR[pdg];
/* Set curve's x boundaries and create
* curves so that they cover the same
* range (if we don't do that one table
* will have values on some range and the
* other one won't have any so interpolation
* will fail) */
table_min[pdg] = min(pdg_L->pd_pwr[0],
pdg_R->pd_pwr[0]) / 2;
table_max[pdg] = max(pdg_L->pd_pwr[pdg_L->pd_points - 1],
pdg_R->pd_pwr[pdg_R->pd_points - 1]) / 2;
/* Now create the curves on surrounding channels
* and interpolate if needed to get the final
* curve for this gain on this channel */
switch (type) {
case AR5K_PWRTABLE_LINEAR_PCDAC:
/* Override min/max so that we don't loose
* accuracy (don't divide by 2) */
table_min[pdg] = min(pdg_L->pd_pwr[0],
pdg_R->pd_pwr[0]);
table_max[pdg] =
max(pdg_L->pd_pwr[pdg_L->pd_points - 1],
pdg_R->pd_pwr[pdg_R->pd_points - 1]);
/* Override minimum so that we don't get
* out of bounds while extrapolating
* below. Don't do this when we have 2
* curves and we are on the high power curve
* because table_min is ok in this case */
if (!(ee->ee_pd_gains[ee_mode] > 1 && pdg == 0)) {
table_min[pdg] =
ath5k_get_linear_pcdac_min(pdg_L->pd_step,
pdg_R->pd_step,
pdg_L->pd_pwr,
pdg_R->pd_pwr);
/* Don't go too low because we will
* miss the upper part of the curve.
* Note: 126 = 31.5dB (max power supported)
* in 0.25dB units */
if (table_max[pdg] - table_min[pdg] > 126)
table_min[pdg] = table_max[pdg] - 126;
}
/* Fall through */
case AR5K_PWRTABLE_PWR_TO_PCDAC:
case AR5K_PWRTABLE_PWR_TO_PDADC:
ath5k_create_power_curve(table_min[pdg],
table_max[pdg],
pdg_L->pd_pwr,
pdg_L->pd_step,
pdg_L->pd_points, tmpL, type);
/* We are in a calibration
* pier, no need to interpolate
* between freq piers */
if (pcinfo_L == pcinfo_R)
continue;
ath5k_create_power_curve(table_min[pdg],
table_max[pdg],
pdg_R->pd_pwr,
pdg_R->pd_step,
pdg_R->pd_points, tmpR, type);
break;
default:
return -EINVAL;
}
/* Interpolate between curves
* of surounding freq piers to
* get the final curve for this
* pd gain. Re-use tmpL for interpolation
* output */
for (i = 0; (i < (u16) (table_max[pdg] - table_min[pdg])) &&
(i < AR5K_EEPROM_POWER_TABLE_SIZE); i++) {
tmpL[i] = (u8) ath5k_get_interpolated_value(target,
(s16) pcinfo_L->freq,
(s16) pcinfo_R->freq,
(s16) tmpL[i],
(s16) tmpR[i]);
}
}
/* Now we have a set of curves for this
* channel on tmpL (x range is table_max - table_min
* and y values are tmpL[pdg][]) sorted in the same
* order as EEPROM (because we've used the backmaping).
* So for RF5112 it's from higher power to lower power
* and for RF2413 it's from lower power to higher power.
* For RF5111 we only have one curve. */
/* Fill min and max power levels for this
* channel by interpolating the values on
* surounding channels to complete the dataset */
ah->ah_txpower.txp_min_pwr = ath5k_get_interpolated_value(target,
(s16) pcinfo_L->freq,
(s16) pcinfo_R->freq,
pcinfo_L->min_pwr, pcinfo_R->min_pwr);
ah->ah_txpower.txp_max_pwr = ath5k_get_interpolated_value(target,
(s16) pcinfo_L->freq,
(s16) pcinfo_R->freq,
pcinfo_L->max_pwr, pcinfo_R->max_pwr);
/* We are ready to go, fill PCDAC/PDADC
* table and write settings on hardware */
switch (type) {
case AR5K_PWRTABLE_LINEAR_PCDAC:
/* For RF5112 we can have one or two curves
* and each curve covers a certain power lvl
* range so we need to do some more processing */
ath5k_combine_linear_pcdac_curves(ah, table_min, table_max,
ee->ee_pd_gains[ee_mode]);
/* Set txp.offset so that we can
* match max power value with max
* table index */
ah->ah_txpower.txp_offset = 64 - (table_max[0] / 2);
/* Write settings on hw */
ath5k_setup_pcdac_table(ah);
break;
case AR5K_PWRTABLE_PWR_TO_PCDAC:
/* We are done for RF5111 since it has only
* one curve, just fit the curve on the table */
ath5k_fill_pwr_to_pcdac_table(ah, table_min, table_max);
/* No rate powertable adjustment for RF5111 */
ah->ah_txpower.txp_min_idx = 0;
ah->ah_txpower.txp_offset = 0;
/* Write settings on hw */
ath5k_setup_pcdac_table(ah);
break;
case AR5K_PWRTABLE_PWR_TO_PDADC:
/* Set PDADC boundaries and fill
* final PDADC table */
ath5k_combine_pwr_to_pdadc_curves(ah, table_min, table_max,
ee->ee_pd_gains[ee_mode]);
/* Write settings on hw */
ath5k_setup_pwr_to_pdadc_table(ah, pdg, pdg_curve_to_idx);
/* Set txp.offset, note that table_min
* can be negative */
ah->ah_txpower.txp_offset = table_min[0];
break;
default:
return -EINVAL;
}
return 0;
}
/*
* Per-rate tx power setting
*
* This is the code that sets the desired tx power (below
* maximum) on hw for each rate (we also have TPC that sets
* power per packet). We do that by providing an index on the
* PCDAC/PDADC table we set up.
*/
/*
* Set rate power table
*
* For now we only limit txpower based on maximum tx power
* supported by hw (what's inside rate_info). We need to limit
* this even more, based on regulatory domain etc.
*
* Rate power table contains indices to PCDAC/PDADC table (0.5dB steps)
* and is indexed as follows:
* rates[0] - rates[7] -> OFDM rates
* rates[8] - rates[14] -> CCK rates
* rates[15] -> XR rates (they all have the same power)
*/
static void
ath5k_setup_rate_powertable(struct ath5k_hw *ah, u16 max_pwr,
struct ath5k_rate_pcal_info *rate_info,
u8 ee_mode)
{
unsigned int i;
u16 *rates;
/* max_pwr is power level we got from driver/user in 0.5dB
* units, switch to 0.25dB units so we can compare */
max_pwr *= 2;
max_pwr = min(max_pwr, (u16) ah->ah_txpower.txp_max_pwr) / 2;
/* apply rate limits */
rates = ah->ah_txpower.txp_rates_power_table;
/* OFDM rates 6 to 24Mb/s */
for (i = 0; i < 5; i++)
rates[i] = min(max_pwr, rate_info->target_power_6to24);
/* Rest OFDM rates */
rates[5] = min(rates[0], rate_info->target_power_36);
rates[6] = min(rates[0], rate_info->target_power_48);
rates[7] = min(rates[0], rate_info->target_power_54);
/* CCK rates */
/* 1L */
rates[8] = min(rates[0], rate_info->target_power_6to24);
/* 2L */
rates[9] = min(rates[0], rate_info->target_power_36);
/* 2S */
rates[10] = min(rates[0], rate_info->target_power_36);
/* 5L */
rates[11] = min(rates[0], rate_info->target_power_48);
/* 5S */
rates[12] = min(rates[0], rate_info->target_power_48);
/* 11L */
rates[13] = min(rates[0], rate_info->target_power_54);
/* 11S */
rates[14] = min(rates[0], rate_info->target_power_54);
/* XR rates */
rates[15] = min(rates[0], rate_info->target_power_6to24);
/* CCK rates have different peak to average ratio
* so we have to tweak their power so that gainf
* correction works ok. For this we use OFDM to
* CCK delta from eeprom */
if ((ee_mode == AR5K_EEPROM_MODE_11G) &&
(ah->ah_phy_revision < AR5K_SREV_PHY_5212A))
for (i = 8; i <= 15; i++)
rates[i] -= ah->ah_txpower.txp_cck_ofdm_gainf_delta;
ah->ah_txpower.txp_min_pwr = rates[7];
ah->ah_txpower.txp_max_pwr = rates[0];
ah->ah_txpower.txp_ofdm = rates[7];
}
/*
* Set transmition power
*/
int
ath5k_hw_txpower(struct ath5k_hw *ah, struct net80211_channel *channel,
u8 ee_mode, u8 txpower)
{
struct ath5k_rate_pcal_info rate_info;
u8 type;
int ret;
if (txpower > AR5K_TUNE_MAX_TXPOWER) {
DBG("ath5k: invalid tx power %d\n", txpower);
return -EINVAL;
}
if (txpower == 0)
txpower = AR5K_TUNE_DEFAULT_TXPOWER;
/* Reset TX power values */
memset(&ah->ah_txpower, 0, sizeof(ah->ah_txpower));
ah->ah_txpower.txp_tpc = AR5K_TUNE_TPC_TXPOWER;
ah->ah_txpower.txp_min_pwr = 0;
ah->ah_txpower.txp_max_pwr = AR5K_TUNE_MAX_TXPOWER;
/* Initialize TX power table */
switch (ah->ah_radio) {
case AR5K_RF5111:
type = AR5K_PWRTABLE_PWR_TO_PCDAC;
break;
case AR5K_RF5112:
type = AR5K_PWRTABLE_LINEAR_PCDAC;
break;
case AR5K_RF2413:
case AR5K_RF5413:
case AR5K_RF2316:
case AR5K_RF2317:
case AR5K_RF2425:
type = AR5K_PWRTABLE_PWR_TO_PDADC;
break;
default:
return -EINVAL;
}
/* FIXME: Only on channel/mode change */
ret = ath5k_setup_channel_powertable(ah, channel, ee_mode, type);
if (ret)
return ret;
/* Limit max power if we have a CTL available */
ath5k_get_max_ctl_power(ah, channel);
/* FIXME: Tx power limit for this regdomain
* XXX: Mac80211/CRDA will do that anyway ? */
/* FIXME: Antenna reduction stuff */
/* FIXME: Limit power on turbo modes */
/* FIXME: TPC scale reduction */
/* Get surounding channels for per-rate power table
* calibration */
ath5k_get_rate_pcal_data(ah, channel, &rate_info);
/* Setup rate power table */
ath5k_setup_rate_powertable(ah, txpower, &rate_info, ee_mode);
/* Write rate power table on hw */
ath5k_hw_reg_write(ah, AR5K_TXPOWER_OFDM(3, 24) |
AR5K_TXPOWER_OFDM(2, 16) | AR5K_TXPOWER_OFDM(1, 8) |
AR5K_TXPOWER_OFDM(0, 0), AR5K_PHY_TXPOWER_RATE1);
ath5k_hw_reg_write(ah, AR5K_TXPOWER_OFDM(7, 24) |
AR5K_TXPOWER_OFDM(6, 16) | AR5K_TXPOWER_OFDM(5, 8) |
AR5K_TXPOWER_OFDM(4, 0), AR5K_PHY_TXPOWER_RATE2);
ath5k_hw_reg_write(ah, AR5K_TXPOWER_CCK(10, 24) |
AR5K_TXPOWER_CCK(9, 16) | AR5K_TXPOWER_CCK(15, 8) |
AR5K_TXPOWER_CCK(8, 0), AR5K_PHY_TXPOWER_RATE3);
ath5k_hw_reg_write(ah, AR5K_TXPOWER_CCK(14, 24) |
AR5K_TXPOWER_CCK(13, 16) | AR5K_TXPOWER_CCK(12, 8) |
AR5K_TXPOWER_CCK(11, 0), AR5K_PHY_TXPOWER_RATE4);
/* FIXME: TPC support */
if (ah->ah_txpower.txp_tpc) {
ath5k_hw_reg_write(ah, AR5K_PHY_TXPOWER_RATE_MAX_TPC_ENABLE |
AR5K_TUNE_MAX_TXPOWER, AR5K_PHY_TXPOWER_RATE_MAX);
ath5k_hw_reg_write(ah,
AR5K_REG_MS(AR5K_TUNE_MAX_TXPOWER, AR5K_TPC_ACK) |
AR5K_REG_MS(AR5K_TUNE_MAX_TXPOWER, AR5K_TPC_CTS) |
AR5K_REG_MS(AR5K_TUNE_MAX_TXPOWER, AR5K_TPC_CHIRP),
AR5K_TPC);
} else {
ath5k_hw_reg_write(ah, AR5K_PHY_TXPOWER_RATE_MAX |
AR5K_TUNE_MAX_TXPOWER, AR5K_PHY_TXPOWER_RATE_MAX);
}
return 0;
}
int ath5k_hw_set_txpower_limit(struct ath5k_hw *ah, u8 mode, u8 txpower)
{
struct net80211_channel *channel = ah->ah_current_channel;
DBG2("ath5k: changing txpower to %d\n", txpower);
return ath5k_hw_txpower(ah, channel, mode, txpower);
}
#undef _ATH5K_PHY