/** @file
This file provides some helper functions which are specific for SD card device.
Copyright (c) 2015 - 2016, Intel Corporation. All rights reserved.<BR>
This program and the accompanying materials
are licensed and made available under the terms and conditions of the BSD License
which accompanies this distribution. The full text of the license may be found at
http://opensource.org/licenses/bsd-license.php
THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
**/
#include "SdMmcPciHcDxe.h"
/**
Send command GO_IDLE_STATE to the device to make it go to Idle State.
Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details.
@param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
@param[in] Slot The slot number of the SD card to send the command to.
@retval EFI_SUCCESS The SD device is reset correctly.
@retval Others The device reset fails.
**/
EFI_STATUS
SdCardReset (
IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
IN UINT8 Slot
)
{
EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
EFI_STATUS Status;
ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
ZeroMem (&Packet, sizeof (Packet));
Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
Packet.Timeout = SD_MMC_HC_GENERIC_TIMEOUT;
SdMmcCmdBlk.CommandIndex = SD_GO_IDLE_STATE;
SdMmcCmdBlk.CommandType = SdMmcCommandTypeBc;
Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL);
return Status;
}
/**
Send command SEND_IF_COND to the device to inquiry the SD Memory Card interface
condition.
Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details.
@param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
@param[in] Slot The slot number of the SD card to send the command to.
@param[in] SupplyVoltage The supplied voltage by the host.
@param[in] CheckPattern The check pattern to be sent to the device.
@retval EFI_SUCCESS The operation is done correctly.
@retval Others The operation fails.
**/
EFI_STATUS
SdCardVoltageCheck (
IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
IN UINT8 Slot,
IN UINT8 SupplyVoltage,
IN UINT8 CheckPattern
)
{
EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
EFI_STATUS Status;
ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
ZeroMem (&Packet, sizeof (Packet));
Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
Packet.Timeout = SD_MMC_HC_GENERIC_TIMEOUT;
SdMmcCmdBlk.CommandIndex = SD_SEND_IF_COND;
SdMmcCmdBlk.CommandType = SdMmcCommandTypeBcr;
SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR7;
SdMmcCmdBlk.CommandArgument = (SupplyVoltage << 8) | CheckPattern;
Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL);
if (!EFI_ERROR (Status)) {
if (SdMmcStatusBlk.Resp0 != SdMmcCmdBlk.CommandArgument) {
return EFI_DEVICE_ERROR;
}
}
return Status;
}
/**
Send command SDIO_SEND_OP_COND to the device to see whether it is SDIO device.
Refer to SDIO Simplified Spec 3 Section 3.2 for details.
@param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
@param[in] Slot The slot number of the SD card to send the command to.
@param[in] VoltageWindow The supply voltage window.
@param[in] S18R The boolean to show if it should switch to 1.8v.
@retval EFI_SUCCESS The operation is done correctly.
@retval Others The operation fails.
**/
EFI_STATUS
SdioSendOpCond (
IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
IN UINT8 Slot,
IN UINT32 VoltageWindow,
IN BOOLEAN S18R
)
{
EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
EFI_STATUS Status;
UINT32 Switch;
ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
ZeroMem (&Packet, sizeof (Packet));
Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
Packet.Timeout = SD_MMC_HC_GENERIC_TIMEOUT;
SdMmcCmdBlk.CommandIndex = SDIO_SEND_OP_COND;
SdMmcCmdBlk.CommandType = SdMmcCommandTypeBcr;
SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR4;
Switch = S18R ? BIT24 : 0;
SdMmcCmdBlk.CommandArgument = (VoltageWindow & 0xFFFFFF) | Switch;
Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL);
return Status;
}
/**
Send command SD_SEND_OP_COND to the device to see whether it is SDIO device.
Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details.
@param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
@param[in] Slot The slot number of the SD card to send the command to.
@param[in] Rca The relative device address of addressed device.
@param[in] VoltageWindow The supply voltage window.
@param[in] S18R The boolean to show if it should switch to 1.8v.
@param[in] Xpc The boolean to show if it should provide 0.36w power control.
@param[in] Hcs The boolean to show if it support host capacity info.
@param[out] Ocr The buffer to store returned OCR register value.
@retval EFI_SUCCESS The operation is done correctly.
@retval Others The operation fails.
**/
EFI_STATUS
SdCardSendOpCond (
IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
IN UINT8 Slot,
IN UINT16 Rca,
IN UINT32 VoltageWindow,
IN BOOLEAN S18R,
IN BOOLEAN Xpc,
IN BOOLEAN Hcs,
OUT UINT32 *Ocr
)
{
EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
EFI_STATUS Status;
UINT32 Switch;
UINT32 MaxPower;
UINT32 HostCapacity;
ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
ZeroMem (&Packet, sizeof (Packet));
Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
Packet.Timeout = SD_MMC_HC_GENERIC_TIMEOUT;
SdMmcCmdBlk.CommandIndex = SD_APP_CMD;
SdMmcCmdBlk.CommandType = SdMmcCommandTypeAc;
SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1;
SdMmcCmdBlk.CommandArgument = (UINT32)Rca << 16;
Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL);
if (EFI_ERROR (Status)) {
return Status;
}
SdMmcCmdBlk.CommandIndex = SD_SEND_OP_COND;
SdMmcCmdBlk.CommandType = SdMmcCommandTypeBcr;
SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR3;
Switch = S18R ? BIT24 : 0;
MaxPower = Xpc ? BIT28 : 0;
HostCapacity = Hcs ? BIT30 : 0;
SdMmcCmdBlk.CommandArgument = (VoltageWindow & 0xFFFFFF) | Switch | MaxPower | HostCapacity;
Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL);
if (!EFI_ERROR (Status)) {
//
// For details, refer to SD Host Controller Simplified Spec 3.0 Table 2-12.
//
*Ocr = SdMmcStatusBlk.Resp0;
}
return Status;
}
/**
Broadcast command ALL_SEND_CID to the bus to ask all the SD devices to send the
data of their CID registers.
Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details.
@param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
@param[in] Slot The slot number of the SD card to send the command to.
@retval EFI_SUCCESS The operation is done correctly.
@retval Others The operation fails.
**/
EFI_STATUS
SdCardAllSendCid (
IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
IN UINT8 Slot
)
{
EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
EFI_STATUS Status;
ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
ZeroMem (&Packet, sizeof (Packet));
Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
Packet.Timeout = SD_MMC_HC_GENERIC_TIMEOUT;
SdMmcCmdBlk.CommandIndex = SD_ALL_SEND_CID;
SdMmcCmdBlk.CommandType = SdMmcCommandTypeBcr;
SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR2;
Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL);
return Status;
}
/**
Send command SET_RELATIVE_ADDR to the SD device to assign a Relative device
Address (RCA).
Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details.
@param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
@param[in] Slot The slot number of the SD card to send the command to.
@param[out] Rca The relative device address to assign.
@retval EFI_SUCCESS The operation is done correctly.
@retval Others The operation fails.
**/
EFI_STATUS
SdCardSetRca (
IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
IN UINT8 Slot,
OUT UINT16 *Rca
)
{
EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
EFI_STATUS Status;
ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
ZeroMem (&Packet, sizeof (Packet));
Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
Packet.Timeout = SD_MMC_HC_GENERIC_TIMEOUT;
SdMmcCmdBlk.CommandIndex = SD_SET_RELATIVE_ADDR;
SdMmcCmdBlk.CommandType = SdMmcCommandTypeBcr;
SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR6;
Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL);
if (!EFI_ERROR (Status)) {
*Rca = (UINT16)(SdMmcStatusBlk.Resp0 >> 16);
}
return Status;
}
/**
Send command SEND_CSD to the SD device to get the data of the CSD register.
Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details.
@param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
@param[in] Slot The slot number of the SD card to send the command to.
@param[in] Rca The relative device address of selected device.
@param[out] Csd The buffer to store the content of the CSD register.
Note the caller should ignore the lowest byte of this
buffer as the content of this byte is meaningless even
if the operation succeeds.
@retval EFI_SUCCESS The operation is done correctly.
@retval Others The operation fails.
**/
EFI_STATUS
SdCardGetCsd (
IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
IN UINT8 Slot,
IN UINT16 Rca,
OUT SD_CSD *Csd
)
{
EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
EFI_STATUS Status;
ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
ZeroMem (&Packet, sizeof (Packet));
Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
Packet.Timeout = SD_MMC_HC_GENERIC_TIMEOUT;
SdMmcCmdBlk.CommandIndex = SD_SEND_CSD;
SdMmcCmdBlk.CommandType = SdMmcCommandTypeAc;
SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR2;
SdMmcCmdBlk.CommandArgument = (UINT32)Rca << 16;
Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL);
if (!EFI_ERROR (Status)) {
//
// For details, refer to SD Host Controller Simplified Spec 3.0 Table 2-12.
//
CopyMem (((UINT8*)Csd) + 1, &SdMmcStatusBlk.Resp0, sizeof (SD_CSD) - 1);
}
return Status;
}
/**
Send command SEND_CSD to the SD device to get the data of the CSD register.
Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details.
@param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
@param[in] Slot The slot number of the SD card to send the command to.
@param[in] Rca The relative device address of selected device.
@param[out] Scr The buffer to store the content of the SCR register.
@retval EFI_SUCCESS The operation is done correctly.
@retval Others The operation fails.
**/
EFI_STATUS
SdCardGetScr (
IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
IN UINT8 Slot,
IN UINT16 Rca,
OUT SD_SCR *Scr
)
{
EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
EFI_STATUS Status;
ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
ZeroMem (&Packet, sizeof (Packet));
Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
Packet.Timeout = SD_MMC_HC_GENERIC_TIMEOUT;
SdMmcCmdBlk.CommandIndex = SD_APP_CMD;
SdMmcCmdBlk.CommandType = SdMmcCommandTypeAc;
SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1;
SdMmcCmdBlk.CommandArgument = (UINT32)Rca << 16;
Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL);
if (EFI_ERROR (Status)) {
return Status;
}
SdMmcCmdBlk.CommandIndex = SD_SEND_SCR;
SdMmcCmdBlk.CommandType = SdMmcCommandTypeAdtc;
SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1;
Packet.InDataBuffer = Scr;
Packet.InTransferLength = sizeof (SD_SCR);
Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL);
return Status;
}
/**
Send command SELECT_DESELECT_CARD to the SD device to select/deselect it.
Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details.
@param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
@param[in] Slot The slot number of the SD card to send the command to.
@param[in] Rca The relative device address of selected device.
@retval EFI_SUCCESS The operation is done correctly.
@retval Others The operation fails.
**/
EFI_STATUS
SdCardSelect (
IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
IN UINT8 Slot,
IN UINT16 Rca
)
{
EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
EFI_STATUS Status;
ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
ZeroMem (&Packet, sizeof (Packet));
Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
Packet.Timeout = SD_MMC_HC_GENERIC_TIMEOUT;
SdMmcCmdBlk.CommandIndex = SD_SELECT_DESELECT_CARD;
SdMmcCmdBlk.CommandType = SdMmcCommandTypeAc;
if (Rca != 0) {
SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1b;
}
SdMmcCmdBlk.CommandArgument = (UINT32)Rca << 16;
Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL);
return Status;
}
/**
Send command VOLTAGE_SWITCH to the SD device to switch the voltage of the device.
Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details.
@param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
@param[in] Slot The slot number of the SD card to send the command to.
@retval EFI_SUCCESS The operation is done correctly.
@retval Others The operation fails.
**/
EFI_STATUS
SdCardVoltageSwitch (
IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
IN UINT8 Slot
)
{
EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
EFI_STATUS Status;
ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
ZeroMem (&Packet, sizeof (Packet));
Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
Packet.Timeout = SD_MMC_HC_GENERIC_TIMEOUT;
SdMmcCmdBlk.CommandIndex = SD_VOLTAGE_SWITCH;
SdMmcCmdBlk.CommandType = SdMmcCommandTypeAc;
SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1;
SdMmcCmdBlk.CommandArgument = 0;
Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL);
return Status;
}
/**
Send command SET_BUS_WIDTH to the SD device to set the bus width.
Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details.
@param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
@param[in] Slot The slot number of the SD card to send the command to.
@param[in] Rca The relative device address of addressed device.
@param[in] BusWidth The bus width to be set, it could be 1 or 4.
@retval EFI_SUCCESS The operation is done correctly.
@retval Others The operation fails.
**/
EFI_STATUS
SdCardSetBusWidth (
IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
IN UINT8 Slot,
IN UINT16 Rca,
IN UINT8 BusWidth
)
{
EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
EFI_STATUS Status;
UINT8 Value;
ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
ZeroMem (&Packet, sizeof (Packet));
Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
Packet.Timeout = SD_MMC_HC_GENERIC_TIMEOUT;
SdMmcCmdBlk.CommandIndex = SD_APP_CMD;
SdMmcCmdBlk.CommandType = SdMmcCommandTypeAc;
SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1;
SdMmcCmdBlk.CommandArgument = (UINT32)Rca << 16;
Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL);
if (EFI_ERROR (Status)) {
return Status;
}
SdMmcCmdBlk.CommandIndex = SD_SET_BUS_WIDTH;
SdMmcCmdBlk.CommandType = SdMmcCommandTypeAc;
SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1;
if (BusWidth == 1) {
Value = 0;
} else if (BusWidth == 4) {
Value = 2;
} else {
return EFI_INVALID_PARAMETER;
}
SdMmcCmdBlk.CommandArgument = Value & 0x3;
Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL);
return Status;
}
/**
Send command SWITCH_FUNC to the SD device to check switchable function or switch card function.
Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details.
@param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
@param[in] Slot The slot number of the SD card to send the command to.
@param[in] AccessMode The value for access mode group.
@param[in] CommandSystem The value for command set group.
@param[in] DriveStrength The value for drive length group.
@param[in] PowerLimit The value for power limit group.
@param[in] Mode Switch or check function.
@param[out] SwitchResp The return switch function status.
@retval EFI_SUCCESS The operation is done correctly.
@retval Others The operation fails.
**/
EFI_STATUS
SdCardSwitch (
IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
IN UINT8 Slot,
IN UINT8 AccessMode,
IN UINT8 CommandSystem,
IN UINT8 DriveStrength,
IN UINT8 PowerLimit,
IN BOOLEAN Mode,
OUT UINT8 *SwitchResp
)
{
EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
EFI_STATUS Status;
UINT32 ModeValue;
ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
ZeroMem (&Packet, sizeof (Packet));
Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
Packet.Timeout = SD_MMC_HC_GENERIC_TIMEOUT;
SdMmcCmdBlk.CommandIndex = SD_SWITCH_FUNC;
SdMmcCmdBlk.CommandType = SdMmcCommandTypeAdtc;
SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1;
ModeValue = Mode ? BIT31 : 0;
SdMmcCmdBlk.CommandArgument = (AccessMode & 0xF) | ((PowerLimit & 0xF) << 4) | \
((DriveStrength & 0xF) << 8) | ((DriveStrength & 0xF) << 12) | \
ModeValue;
Packet.InDataBuffer = SwitchResp;
Packet.InTransferLength = 64;
Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL);
return Status;
}
/**
Send command SEND_STATUS to the addressed SD device to get its status register.
Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details.
@param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
@param[in] Slot The slot number of the SD card to send the command to.
@param[in] Rca The relative device address of addressed device.
@param[out] DevStatus The returned device status.
@retval EFI_SUCCESS The operation is done correctly.
@retval Others The operation fails.
**/
EFI_STATUS
SdCardSendStatus (
IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
IN UINT8 Slot,
IN UINT16 Rca,
OUT UINT32 *DevStatus
)
{
EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
EFI_STATUS Status;
ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
ZeroMem (&Packet, sizeof (Packet));
Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
Packet.Timeout = SD_MMC_HC_GENERIC_TIMEOUT;
SdMmcCmdBlk.CommandIndex = SD_SEND_STATUS;
SdMmcCmdBlk.CommandType = SdMmcCommandTypeAc;
SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1;
SdMmcCmdBlk.CommandArgument = (UINT32)Rca << 16;
Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL);
if (!EFI_ERROR (Status)) {
*DevStatus = SdMmcStatusBlk.Resp0;
}
return Status;
}
/**
Send command SEND_TUNING_BLOCK to the SD device for HS200 optimal sampling point
detection.
It may be sent up to 40 times until the host finishes the tuning procedure.
Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details.
@param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
@param[in] Slot The slot number of the SD card to send the command to.
@retval EFI_SUCCESS The operation is done correctly.
@retval Others The operation fails.
**/
EFI_STATUS
SdCardSendTuningBlk (
IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
IN UINT8 Slot
)
{
EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk;
EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk;
EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet;
EFI_STATUS Status;
UINT8 TuningBlock[64];
ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk));
ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk));
ZeroMem (&Packet, sizeof (Packet));
Packet.SdMmcCmdBlk = &SdMmcCmdBlk;
Packet.SdMmcStatusBlk = &SdMmcStatusBlk;
Packet.Timeout = SD_MMC_HC_GENERIC_TIMEOUT;
SdMmcCmdBlk.CommandIndex = SD_SEND_TUNING_BLOCK;
SdMmcCmdBlk.CommandType = SdMmcCommandTypeAdtc;
SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1;
SdMmcCmdBlk.CommandArgument = 0;
Packet.InDataBuffer = TuningBlock;
Packet.InTransferLength = sizeof (TuningBlock);
Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL);
return Status;
}
/**
Tunning the sampling point of SDR104 or SDR50 bus speed mode.
Command SD_SEND_TUNING_BLOCK may be sent up to 40 times until the host finishes the
tuning procedure.
Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 and
SD Host Controller Simplified Spec 3.0 section Figure 3-7 for details.
@param[in] PciIo A pointer to the EFI_PCI_IO_PROTOCOL instance.
@param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
@param[in] Slot The slot number of the SD card to send the command to.
@retval EFI_SUCCESS The operation is done correctly.
@retval Others The operation fails.
**/
EFI_STATUS
SdCardTuningClock (
IN EFI_PCI_IO_PROTOCOL *PciIo,
IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
IN UINT8 Slot
)
{
EFI_STATUS Status;
UINT8 HostCtrl2;
UINT8 Retry;
//
// Notify the host that the sampling clock tuning procedure starts.
//
HostCtrl2 = BIT6;
Status = SdMmcHcOrMmio (PciIo, Slot, SD_MMC_HC_HOST_CTRL2, sizeof (HostCtrl2), &HostCtrl2);
if (EFI_ERROR (Status)) {
return Status;
}
//
// Ask the device to send a sequence of tuning blocks till the tuning procedure is done.
//
Retry = 0;
do {
Status = SdCardSendTuningBlk (PassThru, Slot);
if (EFI_ERROR (Status)) {
DEBUG ((DEBUG_ERROR, "SdCardSendTuningBlk: Send tuning block fails with %r\n", Status));
return Status;
}
Status = SdMmcHcRwMmio (PciIo, Slot, SD_MMC_HC_HOST_CTRL2, TRUE, sizeof (HostCtrl2), &HostCtrl2);
if (EFI_ERROR (Status)) {
return Status;
}
if ((HostCtrl2 & (BIT6 | BIT7)) == 0) {
break;
}
if ((HostCtrl2 & (BIT6 | BIT7)) == BIT7) {
return EFI_SUCCESS;
}
} while (++Retry < 40);
DEBUG ((DEBUG_ERROR, "SdCardTuningClock: Send tuning block fails at %d times with HostCtrl2 %02x\n", Retry, HostCtrl2));
//
// Abort the tuning procedure and reset the tuning circuit.
//
HostCtrl2 = (UINT8)~(BIT6 | BIT7);
Status = SdMmcHcAndMmio (PciIo, Slot, SD_MMC_HC_HOST_CTRL2, sizeof (HostCtrl2), &HostCtrl2);
if (EFI_ERROR (Status)) {
return Status;
}
return EFI_DEVICE_ERROR;
}
/**
Switch the bus width to specified width.
Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 and
SD Host Controller Simplified Spec 3.0 section Figure 3-7 for details.
@param[in] PciIo A pointer to the EFI_PCI_IO_PROTOCOL instance.
@param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
@param[in] Slot The slot number of the SD card to send the command to.
@param[in] Rca The relative device address to be assigned.
@param[in] BusWidth The bus width to be set, it could be 4 or 8.
@retval EFI_SUCCESS The operation is done correctly.
@retval Others The operation fails.
**/
EFI_STATUS
SdCardSwitchBusWidth (
IN EFI_PCI_IO_PROTOCOL *PciIo,
IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
IN UINT8 Slot,
IN UINT16 Rca,
IN UINT8 BusWidth
)
{
EFI_STATUS Status;
UINT32 DevStatus;
Status = SdCardSetBusWidth (PassThru, Slot, Rca, BusWidth);
if (EFI_ERROR (Status)) {
DEBUG ((DEBUG_ERROR, "SdCardSwitchBusWidth: Switch to bus width %d fails with %r\n", BusWidth, Status));
return Status;
}
Status = SdCardSendStatus (PassThru, Slot, Rca, &DevStatus);
if (EFI_ERROR (Status)) {
DEBUG ((DEBUG_ERROR, "SdCardSwitchBusWidth: Send status fails with %r\n", Status));
return Status;
}
//
// Check the switch operation is really successful or not.
//
if ((DevStatus >> 16) != 0) {
DEBUG ((DEBUG_ERROR, "SdCardSwitchBusWidth: The switch operation fails as DevStatus is 0x%08x\n", DevStatus));
return EFI_DEVICE_ERROR;
}
Status = SdMmcHcSetBusWidth (PciIo, Slot, BusWidth);
return Status;
}
/**
Switch the high speed timing according to request.
Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 and
SD Host Controller Simplified Spec 3.0 section Figure 2-29 for details.
@param[in] PciIo A pointer to the EFI_PCI_IO_PROTOCOL instance.
@param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance.
@param[in] Slot The slot number of the SD card to send the command to.
@param[in] Rca The relative device address to be assigned.
@param[in] S18A The boolean to show if it's a UHS-I SD card.
@retval EFI_SUCCESS The operation is done correctly.
@retval Others The operation fails.
**/
EFI_STATUS
SdCardSetBusMode (
IN EFI_PCI_IO_PROTOCOL *PciIo,
IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru,
IN UINT8 Slot,
IN UINT16 Rca,
IN BOOLEAN S18A
)
{
EFI_STATUS Status;
SD_MMC_HC_SLOT_CAP *Capability;
UINT32 ClockFreq;
UINT8 BusWidth;
UINT8 AccessMode;
UINT8 HostCtrl1;
UINT8 HostCtrl2;
UINT8 SwitchResp[64];
SD_MMC_HC_PRIVATE_DATA *Private;
Private = SD_MMC_HC_PRIVATE_FROM_THIS (PassThru);
Capability = &Private->Capability[Slot];
Status = SdCardSelect (PassThru, Slot, Rca);
if (EFI_ERROR (Status)) {
return Status;
}
BusWidth = 4;
Status = SdCardSwitchBusWidth (PciIo, PassThru, Slot, Rca, BusWidth);
if (EFI_ERROR (Status)) {
return Status;
}
//
// Get the supported bus speed from SWITCH cmd return data group #1.
//
Status = SdCardSwitch (PassThru, Slot, 0xF, 0xF, 0xF, 0xF, FALSE, SwitchResp);
if (EFI_ERROR (Status)) {
return Status;
}
//
// Calculate supported bus speed/bus width/clock frequency by host and device capability.
//
ClockFreq = 0;
if (S18A && (Capability->Sdr104 != 0) && ((SwitchResp[13] & BIT3) != 0)) {
ClockFreq = 208;
AccessMode = 3;
} else if (S18A && (Capability->Sdr50 != 0) && ((SwitchResp[13] & BIT2) != 0)) {
ClockFreq = 100;
AccessMode = 2;
} else if (S18A && (Capability->Ddr50 != 0) && ((SwitchResp[13] & BIT4) != 0)) {
ClockFreq = 50;
AccessMode = 4;
} else if ((SwitchResp[13] & BIT1) != 0) {
ClockFreq = 50;
AccessMode = 1;
} else {
ClockFreq = 25;
AccessMode = 0;
}
Status = SdCardSwitch (PassThru, Slot, AccessMode, 0xF, 0xF, 0xF, TRUE, SwitchResp);
if (EFI_ERROR (Status)) {
return Status;
}
if ((SwitchResp[16] & 0xF) != AccessMode) {
DEBUG ((DEBUG_ERROR, "SdCardSetBusMode: Switch to AccessMode %d ClockFreq %d BusWidth %d fails! The Switch response is 0x%1x\n", AccessMode, ClockFreq, BusWidth, SwitchResp[16] & 0xF));
return EFI_DEVICE_ERROR;
}
DEBUG ((DEBUG_INFO, "SdCardSetBusMode: Switch to AccessMode %d ClockFreq %d BusWidth %d\n", AccessMode, ClockFreq, BusWidth));
//
// Set to Hight Speed timing
//
if (AccessMode == 1) {
HostCtrl1 = BIT2;
Status = SdMmcHcOrMmio (PciIo, Slot, SD_MMC_HC_HOST_CTRL1, sizeof (HostCtrl1), &HostCtrl1);
if (EFI_ERROR (Status)) {
return Status;
}
}
HostCtrl2 = (UINT8)~0x7;
Status = SdMmcHcAndMmio (PciIo, Slot, SD_MMC_HC_HOST_CTRL2, sizeof (HostCtrl2), &HostCtrl2);
if (EFI_ERROR (Status)) {
return Status;
}
HostCtrl2 = AccessMode;
Status = SdMmcHcOrMmio (PciIo, Slot, SD_MMC_HC_HOST_CTRL2, sizeof (HostCtrl2), &HostCtrl2);
if (EFI_ERROR (Status)) {
return Status;
}
Status = SdMmcHcClockSupply (PciIo, Slot, ClockFreq * 1000, *Capability);
if (EFI_ERROR (Status)) {
return Status;
}
if ((AccessMode == 3) || ((AccessMode == 2) && (Capability->TuningSDR50 != 0))) {
Status = SdCardTuningClock (PciIo, PassThru, Slot);
if (EFI_ERROR (Status)) {
return Status;
}
}
return Status;
}
/**
Execute SD device identification procedure.
Refer to SD Physical Layer Simplified Spec 4.1 Section 3.6 for details.
@param[in] Private A pointer to the SD_MMC_HC_PRIVATE_DATA instance.
@param[in] Slot The slot number of the SD card to send the command to.
@retval EFI_SUCCESS There is a SD card.
@retval Others There is not a SD card.
**/
EFI_STATUS
SdCardIdentification (
IN SD_MMC_HC_PRIVATE_DATA *Private,
IN UINT8 Slot
)
{
EFI_STATUS Status;
EFI_PCI_IO_PROTOCOL *PciIo;
EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru;
UINT32 Ocr;
UINT16 Rca;
BOOLEAN Xpc;
BOOLEAN S18r;
UINT64 MaxCurrent;
UINT16 ControllerVer;
UINT8 PowerCtrl;
UINT32 PresentState;
UINT8 HostCtrl2;
PciIo = Private->PciIo;
PassThru = &Private->PassThru;
//
// 1. Send Cmd0 to the device
//
Status = SdCardReset (PassThru, Slot);
if (EFI_ERROR (Status)) {
DEBUG ((DEBUG_INFO, "SdCardIdentification: Executing Cmd0 fails with %r\n", Status));
return Status;
}
//
// 2. Send Cmd8 to the device
//
Status = SdCardVoltageCheck (PassThru, Slot, 0x1, 0xFF);
if (EFI_ERROR (Status)) {
DEBUG ((DEBUG_INFO, "SdCardIdentification: Executing Cmd8 fails with %r\n", Status));
return Status;
}
//
// 3. Send SDIO Cmd5 to the device to the SDIO device OCR register.
//
Status = SdioSendOpCond (PassThru, Slot, 0, FALSE);
if (!EFI_ERROR (Status)) {
DEBUG ((DEBUG_INFO, "SdCardIdentification: Found SDIO device, ignore it as we don't support\n"));
return EFI_DEVICE_ERROR;
}
//
// 4. Send Acmd41 with voltage window 0 to the device
//
Status = SdCardSendOpCond (PassThru, Slot, 0, 0, FALSE, FALSE, FALSE, &Ocr);
if (EFI_ERROR (Status)) {
DEBUG ((DEBUG_INFO, "SdCardIdentification: Executing SdCardSendOpCond fails with %r\n", Status));
return EFI_DEVICE_ERROR;
}
if (Private->Capability[Slot].Voltage33 != 0) {
//
// Support 3.3V
//
MaxCurrent = ((UINT32)Private->MaxCurrent[Slot] & 0xFF) * 4;
} else if (Private->Capability[Slot].Voltage30 != 0) {
//
// Support 3.0V
//
MaxCurrent = (((UINT32)Private->MaxCurrent[Slot] >> 8) & 0xFF) * 4;
} else if (Private->Capability[Slot].Voltage18 != 0) {
//
// Support 1.8V
//
MaxCurrent = (((UINT32)Private->MaxCurrent[Slot] >> 16) & 0xFF) * 4;
} else {
ASSERT (FALSE);
return EFI_DEVICE_ERROR;
}
if (MaxCurrent >= 150) {
Xpc = TRUE;
} else {
Xpc = FALSE;
}
Status = SdMmcHcRwMmio (PciIo, Slot, SD_MMC_HC_CTRL_VER, TRUE, sizeof (ControllerVer), &ControllerVer);
if (EFI_ERROR (Status)) {
return Status;
}
if ((ControllerVer & 0xFF) == 2) {
S18r = TRUE;
} else if (((ControllerVer & 0xFF) == 0) || ((ControllerVer & 0xFF) == 1)) {
S18r = FALSE;
} else {
ASSERT (FALSE);
return EFI_UNSUPPORTED;
}
//
// 5. Repeatly send Acmd41 with supply voltage window to the device.
// Note here we only support the cards complied with SD physical
// layer simplified spec version 2.0 and version 3.0 and above.
//
do {
Status = SdCardSendOpCond (PassThru, Slot, 0, Ocr, S18r, Xpc, TRUE, &Ocr);
if (EFI_ERROR (Status)) {
DEBUG ((DEBUG_ERROR, "SdCardIdentification: SdCardSendOpCond fails with %r Ocr %x, S18r %x, Xpc %x\n", Status, Ocr, S18r, Xpc));
return EFI_DEVICE_ERROR;
}
} while ((Ocr & BIT31) == 0);
//
// 6. If the S18A bit is set and the Host Controller supports 1.8V signaling
// (One of support bits is set to 1: SDR50, SDR104 or DDR50 in the
// Capabilities register), switch its voltage to 1.8V.
//
if ((Private->Capability[Slot].Sdr50 != 0 ||
Private->Capability[Slot].Sdr104 != 0 ||
Private->Capability[Slot].Ddr50 != 0) &&
((Ocr & BIT24) != 0)) {
Status = SdCardVoltageSwitch (PassThru, Slot);
if (EFI_ERROR (Status)) {
DEBUG ((DEBUG_ERROR, "SdCardIdentification: Executing SdCardVoltageSwitch fails with %r\n", Status));
Status = EFI_DEVICE_ERROR;
goto Error;
} else {
Status = SdMmcHcStopClock (PciIo, Slot);
if (EFI_ERROR (Status)) {
Status = EFI_DEVICE_ERROR;
goto Error;
}
SdMmcHcRwMmio (PciIo, Slot, SD_MMC_HC_PRESENT_STATE, TRUE, sizeof (PresentState), &PresentState);
if (((PresentState >> 20) & 0xF) != 0) {
DEBUG ((DEBUG_ERROR, "SdCardIdentification: SwitchVoltage fails with PresentState = 0x%x\n", PresentState));
Status = EFI_DEVICE_ERROR;
goto Error;
}
HostCtrl2 = BIT3;
SdMmcHcOrMmio (PciIo, Slot, SD_MMC_HC_HOST_CTRL2, sizeof (HostCtrl2), &HostCtrl2);
gBS->Stall (5000);
SdMmcHcRwMmio (PciIo, Slot, SD_MMC_HC_HOST_CTRL2, TRUE, sizeof (HostCtrl2), &HostCtrl2);
if ((HostCtrl2 & BIT3) == 0) {
DEBUG ((DEBUG_ERROR, "SdCardIdentification: SwitchVoltage fails with HostCtrl2 = 0x%x\n", HostCtrl2));
Status = EFI_DEVICE_ERROR;
goto Error;
}
SdMmcHcInitClockFreq (PciIo, Slot, Private->Capability[Slot]);
gBS->Stall (1000);
SdMmcHcRwMmio (PciIo, Slot, SD_MMC_HC_PRESENT_STATE, TRUE, sizeof (PresentState), &PresentState);
if (((PresentState >> 20) & 0xF) != 0xF) {
DEBUG ((DEBUG_ERROR, "SdCardIdentification: SwitchVoltage fails with PresentState = 0x%x, It should be 0xF\n", PresentState));
Status = EFI_DEVICE_ERROR;
goto Error;
}
}
DEBUG ((DEBUG_INFO, "SdCardIdentification: Switch to 1.8v signal voltage success\n"));
}
Status = SdCardAllSendCid (PassThru, Slot);
if (EFI_ERROR (Status)) {
DEBUG ((DEBUG_ERROR, "SdCardIdentification: Executing SdCardAllSendCid fails with %r\n", Status));
return Status;
}
Status = SdCardSetRca (PassThru, Slot, &Rca);
if (EFI_ERROR (Status)) {
DEBUG ((DEBUG_ERROR, "SdCardIdentification: Executing SdCardSetRca fails with %r\n", Status));
return Status;
}
//
// Enter Data Tranfer Mode.
//
DEBUG ((DEBUG_INFO, "SdCardIdentification: Found a SD device at slot [%d]\n", Slot));
Private->Slot[Slot].CardType = SdCardType;
Status = SdCardSetBusMode (PciIo, PassThru, Slot, Rca, ((Ocr & BIT24) != 0));
return Status;
Error:
//
// Set SD Bus Power = 0
//
PowerCtrl = (UINT8)~BIT0;
Status = SdMmcHcAndMmio (PciIo, Slot, SD_MMC_HC_POWER_CTRL, sizeof (PowerCtrl), &PowerCtrl);
return EFI_DEVICE_ERROR;
}