/* * i82365.h 1.15 1999/10/25 20:03:34 * * The contents of this file may be used under the * terms of the GNU General Public License version 2 (the "GPL"). * * Software distributed under the License is distributed on an "AS IS" * basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See * the License for the specific language governing rights and * limitations under the License. * * The initial developer of the original code is David A. Hinds * <dahinds@users.sourceforge.net>. Portions created by David A. Hinds * are Copyright (C) 1999 David A. Hinds. All Rights Reserved. */ #ifndef _LINUX_I82365_H #define _LINUX_I82365_H /* register definitions for the Intel 82365SL PCMCIA controller */ /* Offsets for PCIC registers */ #define I365_IDENT 0x00 /* Identification and revision */ #define I365_STATUS 0x01 /* Interface status */ #define I365_POWER 0x02 /* Power and RESETDRV control */ #define I365_INTCTL 0x03 /* Interrupt and general control */ #define I365_CSC 0x04 /* Card status change */ #define I365_CSCINT 0x05 /* Card status change interrupt control */ #define I365_ADDRWIN 0x06 /* Address window enable */ #define I365_IOCTL 0x07 /* I/O control */ #define I365_GENCTL 0x16 /* Card detect and general control */ #define I365_GBLCTL 0x1E /* Global control register */ /* Offsets for I/O and memory window registers */ #define I365_IO(map) (0x08+((map)<<2)) #define I365_MEM(map) (0x10+((map)<<3)) #define I365_W_START 0 #define I365_W_STOP 2 #define I365_W_OFF 4 /* Flags for I365_STATUS */ #define I365_CS_BVD1 0x01 #define I365_CS_STSCHG 0x01 #define I365_CS_BVD2 0x02 #define I365_CS_SPKR 0x02 #define I365_CS_DETECT 0x0C #define I365_CS_WRPROT 0x10 #define I365_CS_READY 0x20 /* Inverted */ #define I365_CS_POWERON 0x40 #define I365_CS_GPI 0x80 /* Flags for I365_POWER */ #define I365_PWR_OFF 0x00 /* Turn off the socket */ #define I365_PWR_OUT 0x80 /* Output enable */ #define I365_PWR_NORESET 0x40 /* Disable RESETDRV on resume */ #define I365_PWR_AUTO 0x20 /* Auto pwr switch enable */ #define I365_VCC_MASK 0x18 /* Mask for turning off Vcc */ /* There are different layouts for B-step and DF-step chips: the B step has independent Vpp1/Vpp2 control, and the DF step has only Vpp1 control, plus 3V control */ #define I365_VCC_5V 0x10 /* Vcc = 5.0v */ #define I365_VCC_3V 0x18 /* Vcc = 3.3v */ #define I365_VPP2_MASK 0x0c /* Mask for turning off Vpp2 */ #define I365_VPP2_5V 0x04 /* Vpp2 = 5.0v */ #define I365_VPP2_12V 0x08 /* Vpp2 = 12.0v */ #define I365_VPP1_MASK 0x03 /* Mask for turning off Vpp1 */ #define I365_VPP1_5V 0x01 /* Vpp2 = 5.0v */ #define I365_VPP1_12V 0x02 /* Vpp2 = 12.0v */ /* Flags for I365_INTCTL */ #define I365_RING_ENA 0x80 #define I365_PC_RESET 0x40 #define I365_PC_IOCARD 0x20 #define I365_INTR_ENA 0x10 #define I365_IRQ_MASK 0x0F /* Flags for I365_CSC and I365_CSCINT*/ #define I365_CSC_BVD1 0x01 #define I365_CSC_STSCHG 0x01 #define I365_CSC_BVD2 0x02 #define I365_CSC_READY 0x04 #define I365_CSC_DETECT 0x08 #define I365_CSC_ANY 0x0F #define I365_CSC_GPI 0x10 /* Flags for I365_ADDRWIN */ #define I365_ENA_IO(map) (0x40 << (map)) #define I365_ENA_MEM(map) (0x01 << (map)) /* Flags for I365_IOCTL */ #define I365_IOCTL_MASK(map) (0x0F << (map<<2)) #define I365_IOCTL_WAIT(map) (0x08 << (map<<2)) #define I365_IOCTL_0WS(map) (0x04 << (map<<2)) #define I365_IOCTL_IOCS16(map) (0x02 << (map<<2)) #define I365_IOCTL_16BIT(map) (0x01 << (map<<2)) /* Flags for I365_GENCTL */ #define I365_CTL_16DELAY 0x01 #define I365_CTL_RESET 0x02 #define I365_CTL_GPI_ENA 0x04 #define I365_CTL_GPI_CTL 0x08 #define I365_CTL_RESUME 0x10 #define I365_CTL_SW_IRQ 0x20 /* Flags for I365_GBLCTL */ #define I365_GBL_PWRDOWN 0x01 #define I365_GBL_CSC_LEV 0x02 #define I365_GBL_WRBACK 0x04 #define I365_GBL_IRQ_0_LEV 0x08 #define I365_GBL_IRQ_1_LEV 0x10 /* Flags for memory window registers */ #define I365_MEM_16BIT 0x8000 /* In memory start high byte */ #define I365_MEM_0WS 0x4000 #define I365_MEM_WS1 0x8000 /* In memory stop high byte */ #define I365_MEM_WS0 0x4000 #define I365_MEM_WRPROT 0x8000 /* In offset high byte */ #define I365_MEM_REG 0x4000 #define I365_REG(slot, reg) (((slot) << 6) + reg) #endif /* _LINUX_I82365_H */ //***************************************************************************** //***************************************************************************** //***************************************************************************** //***************************************************************************** //***************************************************************************** // Beginning vg468.h (for VADEM chipset) #ifndef _LINUX_VG468_H #define _LINUX_VG468_H /* Special bit in I365_IDENT used for Vadem chip detection */ #define I365_IDENT_VADEM 0x08 /* Special definitions in I365_POWER */ #define VG468_VPP2_MASK 0x0c #define VG468_VPP2_5V 0x04 #define VG468_VPP2_12V 0x08 /* Unique Vadem registers */ #define VG469_VSENSE 0x1f /* Card voltage sense */ #define VG469_VSELECT 0x2f /* Card voltage select */ #define VG468_CTL 0x38 /* Control register */ #define VG468_TIMER 0x39 /* Timer control */ #define VG468_MISC 0x3a /* Miscellaneous */ #define VG468_GPIO_CFG 0x3b /* GPIO configuration */ #define VG469_EXT_MODE 0x3c /* Extended mode register */ #define VG468_SELECT 0x3d /* Programmable chip select */ #define VG468_SELECT_CFG 0x3e /* Chip select configuration */ #define VG468_ATA 0x3f /* ATA control */ /* Flags for VG469_VSENSE */ #define VG469_VSENSE_A_VS1 0x01 #define VG469_VSENSE_A_VS2 0x02 #define VG469_VSENSE_B_VS1 0x04 #define VG469_VSENSE_B_VS2 0x08 /* Flags for VG469_VSELECT */ #define VG469_VSEL_VCC 0x03 #define VG469_VSEL_5V 0x00 #define VG469_VSEL_3V 0x03 #define VG469_VSEL_MAX 0x0c #define VG469_VSEL_EXT_STAT 0x10 #define VG469_VSEL_EXT_BUS 0x20 #define VG469_VSEL_MIXED 0x40 #define VG469_VSEL_ISA 0x80 /* Flags for VG468_CTL */ #define VG468_CTL_SLOW 0x01 /* 600ns memory timing */ #define VG468_CTL_ASYNC 0x02 /* Asynchronous bus clocking */ #define VG468_CTL_TSSI 0x08 /* Tri-state some outputs */ #define VG468_CTL_DELAY 0x10 /* Card detect debounce */ #define VG468_CTL_INPACK 0x20 /* Obey INPACK signal? */ #define VG468_CTL_POLARITY 0x40 /* VCCEN polarity */ #define VG468_CTL_COMPAT 0x80 /* Compatibility stuff */ #define VG469_CTL_WS_COMPAT 0x04 /* Wait state compatibility */ #define VG469_CTL_STRETCH 0x10 /* LED stretch */ /* Flags for VG468_TIMER */ #define VG468_TIMER_ZEROPWR 0x10 /* Zero power control */ #define VG468_TIMER_SIGEN 0x20 /* Power up */ #define VG468_TIMER_STATUS 0x40 /* Activity timer status */ #define VG468_TIMER_RES 0x80 /* Timer resolution */ #define VG468_TIMER_MASK 0x0f /* Activity timer timeout */ /* Flags for VG468_MISC */ #define VG468_MISC_GPIO 0x04 /* General-purpose IO */ #define VG468_MISC_DMAWSB 0x08 /* DMA wait state control */ #define VG469_MISC_LEDENA 0x10 /* LED enable */ #define VG468_MISC_VADEMREV 0x40 /* Vadem revision control */ #define VG468_MISC_UNLOCK 0x80 /* Unique register lock */ /* Flags for VG469_EXT_MODE_A */ #define VG469_MODE_VPPST 0x03 /* Vpp steering control */ #define VG469_MODE_INT_SENSE 0x04 /* Internal voltage sense */ #define VG469_MODE_CABLE 0x08 #define VG469_MODE_COMPAT 0x10 /* i82365sl B or DF step */ #define VG469_MODE_TEST 0x20 #define VG469_MODE_RIO 0x40 /* Steer RIO to INTR? */ /* Flags for VG469_EXT_MODE_B */ #define VG469_MODE_B_3V 0x01 /* 3.3v for socket B */ #endif /* _LINUX_VG468_H */ //***************************************************************************** //***************************************************************************** //***************************************************************************** //***************************************************************************** //***************************************************************************** // Beginning ricoh.h (RICOH chipsets) #ifndef _LINUX_RICOH_H #define _LINUX_RICOH_H #define RF5C_MODE_CTL 0x1f /* Mode control */ #define RF5C_PWR_CTL 0x2f /* Mixed voltage control */ #define RF5C_CHIP_ID 0x3a /* Chip identification */ #define RF5C_MODE_CTL_3 0x3b /* Mode control 3 */ /* I/O window address offset */ #define RF5C_IO_OFF(w) (0x36+((w)<<1)) /* Flags for RF5C_MODE_CTL */ #define RF5C_MODE_ATA 0x01 /* ATA mode */ #define RF5C_MODE_LED_ENA 0x02 /* IRQ 12 is LED */ #define RF5C_MODE_CA21 0x04 #define RF5C_MODE_CA22 0x08 #define RF5C_MODE_CA23 0x10 #define RF5C_MODE_CA24 0x20 #define RF5C_MODE_CA25 0x40 #define RF5C_MODE_3STATE_BIT7 0x80 /* Flags for RF5C_PWR_CTL */ #define RF5C_PWR_VCC_3V 0x01 #define RF5C_PWR_IREQ_HIGH 0x02 #define RF5C_PWR_INPACK_ENA 0x04 #define RF5C_PWR_5V_DET 0x08 #define RF5C_PWR_TC_SEL 0x10 /* Terminal Count: irq 11 or 15 */ #define RF5C_PWR_DREQ_LOW 0x20 #define RF5C_PWR_DREQ_OFF 0x00 /* DREQ steering control */ #define RF5C_PWR_DREQ_INPACK 0x40 #define RF5C_PWR_DREQ_SPKR 0x80 #define RF5C_PWR_DREQ_IOIS16 0xc0 /* Values for RF5C_CHIP_ID */ #define RF5C_CHIP_RF5C296 0x32 #define RF5C_CHIP_RF5C396 0xb2 /* Flags for RF5C_MODE_CTL_3 */ #define RF5C_MCTL3_DISABLE 0x01 /* Disable PCMCIA interface */ #define RF5C_MCTL3_DMA_ENA 0x02 /* Register definitions for Ricoh PCI-to-CardBus bridges */ /* Extra bits in CB_BRIDGE_CONTROL */ #define RL5C46X_BCR_3E0_ENA 0x0800 #define RL5C46X_BCR_3E2_ENA 0x1000 /* Bridge Configuration Register */ #define RL5C4XX_CONFIG 0x80 /* 16 bit */ #define RL5C4XX_CONFIG_IO_1_MODE 0x0200 #define RL5C4XX_CONFIG_IO_0_MODE 0x0100 #define RL5C4XX_CONFIG_PREFETCH 0x0001 /* Misc Control Register */ #define RL5C4XX_MISC 0x0082 /* 16 bit */ #define RL5C4XX_MISC_HW_SUSPEND_ENA 0x0002 #define RL5C4XX_MISC_VCCEN_POL 0x0100 #define RL5C4XX_MISC_VPPEN_POL 0x0200 #define RL5C46X_MISC_SUSPEND 0x0001 #define RL5C46X_MISC_PWR_SAVE_2 0x0004 #define RL5C46X_MISC_IFACE_BUSY 0x0008 #define RL5C46X_MISC_B_LOCK 0x0010 #define RL5C46X_MISC_A_LOCK 0x0020 #define RL5C46X_MISC_PCI_LOCK 0x0040 #define RL5C47X_MISC_IFACE_BUSY 0x0004 #define RL5C47X_MISC_PCI_INT_MASK 0x0018 #define RL5C47X_MISC_PCI_INT_DIS 0x0020 #define RL5C47X_MISC_SUBSYS_WR 0x0040 #define RL5C47X_MISC_SRIRQ_ENA 0x0080 #define RL5C47X_MISC_5V_DISABLE 0x0400 #define RL5C47X_MISC_LED_POL 0x0800 /* 16-bit Interface Control Register */ #define RL5C4XX_16BIT_CTL 0x0084 /* 16 bit */ #define RL5C4XX_16CTL_IO_TIMING 0x0100 #define RL5C4XX_16CTL_MEM_TIMING 0x0200 #define RL5C46X_16CTL_LEVEL_1 0x0010 #define RL5C46X_16CTL_LEVEL_2 0x0020 /* 16-bit IO and memory timing registers */ #define RL5C4XX_16BIT_IO_0 0x0088 /* 16 bit */ #define RL5C4XX_16BIT_MEM_0 0x0088 /* 16 bit */ #define RL5C4XX_SETUP_MASK 0x0007 #define RL5C4XX_SETUP_SHIFT 0 #define RL5C4XX_CMD_MASK 0x01f0 #define RL5C4XX_CMD_SHIFT 4 #define RL5C4XX_HOLD_MASK 0x1c00 #define RL5C4XX_HOLD_SHIFT 10 #define RL5C4XX_MISC_CONTROL 0x2F /* 8 bit */ #define RL5C4XX_ZV_ENABLE 0x08 #endif /* _LINUX_RICOH_H */ //***************************************************************************** //***************************************************************************** //***************************************************************************** //***************************************************************************** //***************************************************************************** // Beginning cirrus.h (CIRRUS chipsets) #ifndef _LINUX_CIRRUS_H #define _LINUX_CIRRUS_H #ifndef PCI_VENDOR_ID_CIRRUS #define PCI_VENDOR_ID_CIRRUS 0x1013 #endif #ifndef PCI_DEVICE_ID_CIRRUS_6729 #define PCI_DEVICE_ID_CIRRUS_6729 0x1100 #endif #ifndef PCI_DEVICE_ID_CIRRUS_6832 #define PCI_DEVICE_ID_CIRRUS_6832 0x1110 #endif #define PD67_MISC_CTL_1 0x16 /* Misc control 1 */ #define PD67_FIFO_CTL 0x17 /* FIFO control */ #define PD67_MISC_CTL_2 0x1E /* Misc control 2 */ #define PD67_CHIP_INFO 0x1f /* Chip information */ #define PD67_ATA_CTL 0x026 /* 6730: ATA control */ #define PD67_EXT_INDEX 0x2e /* Extension index */ #define PD67_EXT_DATA 0x2f /* Extension data */ /* PD6722 extension registers -- indexed in PD67_EXT_INDEX */ #define PD67_DATA_MASK0 0x01 /* Data mask 0 */ #define PD67_DATA_MASK1 0x02 /* Data mask 1 */ #define PD67_DMA_CTL 0x03 /* DMA control */ /* PD6730 extension registers -- indexed in PD67_EXT_INDEX */ #define PD67_EXT_CTL_1 0x03 /* Extension control 1 */ #define PD67_MEM_PAGE(n) ((n)+5) /* PCI window bits 31:24 */ #define PD67_EXTERN_DATA 0x0a #define PD67_MISC_CTL_3 0x25 #define PD67_SMB_PWR_CTL 0x26 /* I/O window address offset */ #define PD67_IO_OFF(w) (0x36+((w)<<1)) /* Timing register sets */ #define PD67_TIME_SETUP(n) (0x3a + 3*(n)) #define PD67_TIME_CMD(n) (0x3b + 3*(n)) #define PD67_TIME_RECOV(n) (0x3c + 3*(n)) /* Flags for PD67_MISC_CTL_1 */ #define PD67_MC1_5V_DET 0x01 /* 5v detect */ #define PD67_MC1_MEDIA_ENA 0x01 /* 6730: Multimedia enable */ #define PD67_MC1_VCC_3V 0x02 /* 3.3v Vcc */ #define PD67_MC1_PULSE_MGMT 0x04 #define PD67_MC1_PULSE_IRQ 0x08 #define PD67_MC1_SPKR_ENA 0x10 #define PD67_MC1_INPACK_ENA 0x80 /* Flags for PD67_FIFO_CTL */ #define PD67_FIFO_EMPTY 0x80 /* Flags for PD67_MISC_CTL_2 */ #define PD67_MC2_FREQ_BYPASS 0x01 #define PD67_MC2_DYNAMIC_MODE 0x02 #define PD67_MC2_SUSPEND 0x04 #define PD67_MC2_5V_CORE 0x08 #define PD67_MC2_LED_ENA 0x10 /* IRQ 12 is LED enable */ #define PD67_MC2_FAST_PCI 0x10 /* 6729: PCI bus > 25 MHz */ #define PD67_MC2_3STATE_BIT7 0x20 /* Floppy change bit */ #define PD67_MC2_DMA_MODE 0x40 #define PD67_MC2_IRQ15_RI 0x80 /* IRQ 15 is ring enable */ /* Flags for PD67_CHIP_INFO */ #define PD67_INFO_SLOTS 0x20 /* 0 = 1 slot, 1 = 2 slots */ #define PD67_INFO_CHIP_ID 0xc0 #define PD67_INFO_REV 0x1c /* Fields in PD67_TIME_* registers */ #define PD67_TIME_SCALE 0xc0 #define PD67_TIME_SCALE_1 0x00 #define PD67_TIME_SCALE_16 0x40 #define PD67_TIME_SCALE_256 0x80 #define PD67_TIME_SCALE_4096 0xc0 #define PD67_TIME_MULT 0x3f /* Fields in PD67_DMA_CTL */ #define PD67_DMA_MODE 0xc0 #define PD67_DMA_OFF 0x00 #define PD67_DMA_DREQ_INPACK 0x40 #define PD67_DMA_DREQ_WP 0x80 #define PD67_DMA_DREQ_BVD2 0xc0 #define PD67_DMA_PULLUP 0x20 /* Disable socket pullups? */ /* Fields in PD67_EXT_CTL_1 */ #define PD67_EC1_VCC_PWR_LOCK 0x01 #define PD67_EC1_AUTO_PWR_CLEAR 0x02 #define PD67_EC1_LED_ENA 0x04 #define PD67_EC1_INV_CARD_IRQ 0x08 #define PD67_EC1_INV_MGMT_IRQ 0x10 #define PD67_EC1_PULLUP_CTL 0x20 /* Fields in PD67_MISC_CTL_3 */ #define PD67_MC3_IRQ_MASK 0x03 #define PD67_MC3_IRQ_PCPCI 0x00 #define PD67_MC3_IRQ_EXTERN 0x01 #define PD67_MC3_IRQ_PCIWAY 0x02 #define PD67_MC3_IRQ_PCI 0x03 #define PD67_MC3_PWR_MASK 0x0c #define PD67_MC3_PWR_SERIAL 0x00 #define PD67_MC3_PWR_TI2202 0x08 #define PD67_MC3_PWR_SMB 0x0c /* Register definitions for Cirrus PD6832 PCI-to-CardBus bridge */ /* PD6832 extension registers -- indexed in PD67_EXT_INDEX */ #define PD68_EXT_CTL_2 0x0b #define PD68_PCI_SPACE 0x22 #define PD68_PCCARD_SPACE 0x23 #define PD68_WINDOW_TYPE 0x24 #define PD68_EXT_CSC 0x2e #define PD68_MISC_CTL_4 0x2f #define PD68_MISC_CTL_5 0x30 #define PD68_MISC_CTL_6 0x31 /* Extra flags in PD67_MISC_CTL_3 */ #define PD68_MC3_HW_SUSP 0x10 #define PD68_MC3_MM_EXPAND 0x40 #define PD68_MC3_MM_ARM 0x80 /* Bridge Control Register */ #define PD6832_BCR_MGMT_IRQ_ENA 0x0800 /* Socket Number Register */ #define PD6832_SOCKET_NUMBER 0x004c /* 8 bit */ #endif /* _LINUX_CIRRUS_H */