/** @file
Intel QNC SMBUS library implementation built upon I/O library.
Copyright (c) 2013-2015 Intel Corporation.
This program and the accompanying materials
are licensed and made available under the terms and conditions of the BSD License
which accompanies this distribution. The full text of the license may be found at
http://opensource.org/licenses/bsd-license.php
THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
**/
//
// Include common header file for this module.
//
#include "CommonHeader.h"
/**
Gets Io port base address of Smbus Host Controller.
This internal function depends on a feature flag named PcdIchSmbusFixedIoPortBaseAddress
to retrieve Smbus Io port base. If that feature flag is true, it will get Smbus Io port base
address from a preset Pcd entry named PcdIchSmbusIoPortBaseAddress; otherwise, it will always
read Pci configuration space to get that value in each Smbus bus transaction.
@return The Io port base address of Smbus host controller.
**/
UINTN
InternalGetSmbusIoPortBaseAddress (
VOID
)
{
UINTN IoPortBaseAddress;
if (FeaturePcdGet (PcdSmbaIoBaseAddressFixed)) {
IoPortBaseAddress = (UINTN) PcdGet16 (PcdSmbaIoBaseAddress);
} else {
IoPortBaseAddress = (UINTN) LpcPciCfg32 (R_QNC_LPC_SMBUS_BASE) & B_QNC_LPC_SMBUS_BASE_MASK;
}
//
// Make sure that the IO port base address has been properly set.
//
ASSERT (IoPortBaseAddress != 0);
return IoPortBaseAddress;
}
/**
Acquires the ownership of SMBUS.
This internal function reads the host state register.
If the SMBUS is not available, RETURN_TIMEOUT is returned;
Otherwise, it performs some basic initializations and returns
RETURN_SUCCESS.
@param IoPortBaseAddress The Io port base address of Smbus Host controller.
@retval RETURN_SUCCESS The SMBUS command was executed successfully.
@retval RETURN_TIMEOUT A timeout occurred while executing the SMBUS command.
**/
RETURN_STATUS
InternalSmBusAcquire (
UINTN IoPortBaseAddress
)
{
//
// Clear host status register and exit.
//
IoWrite8 (IoPortBaseAddress + R_QNC_SMBUS_HCTL, 0);
IoWrite8 (IoPortBaseAddress + R_QNC_SMBUS_HD0, 0);
IoWrite8 (IoPortBaseAddress + R_QNC_SMBUS_HD1, 0);
IoWrite8 (IoPortBaseAddress + R_QNC_SMBUS_HSTS, B_QNC_SMBUS_HSTS_ALL);
return RETURN_SUCCESS;
}
/**
Starts the SMBUS transaction and waits until the end.
This internal function start the SMBUS transaction and waits until the transaction
of SMBUS is over by polling the INTR bit of Host status register.
If the SMBUS is not available, RETURN_TIMEOUT is returned;
Otherwise, it performs some basic initializations and returns
RETURN_SUCCESS.
@param IoPortBaseAddress The Io port base address of Smbus Host controller.
@param HostControl The Host control command to start SMBUS transaction.
@retval RETURN_SUCCESS The SMBUS command was executed successfully.
@retval RETURN_CRC_ERROR The checksum is not correct (PEC is incorrect).
@retval RETURN_DEVICE_ERROR The request was not completed because a failure reflected
in the Host Status Register bit. Device errors are
a result of a transaction collision, illegal command field,
unclaimed cycle (host initiated), or bus errors (collisions).
**/
RETURN_STATUS
InternalSmBusStart (
IN UINTN IoPortBaseAddress,
IN UINT8 HostControl
)
{
UINT8 HostStatus;
//
// Set Host Control Register (Initiate Operation, Interrupt disabled).
//
IoWrite8 (IoPortBaseAddress + R_QNC_SMBUS_HCTL, HostControl + B_QNC_SMBUS_START);
do {
//
// Poll INTR bit of Host Status Register.
//
HostStatus = IoRead8 (IoPortBaseAddress + R_QNC_SMBUS_HSTS);
} while ((HostStatus & (B_QNC_SMBUS_BYTE_DONE_STS | B_QNC_SMBUS_DERR | B_QNC_SMBUS_BERR)) == 0);
if ((HostStatus & (B_QNC_SMBUS_DERR | B_QNC_SMBUS_BERR)) == 0) {
return RETURN_SUCCESS;
}
//
// Clear error bits of Host Status Register.
//
IoWrite8 (IoPortBaseAddress + R_QNC_SMBUS_HSTS, (B_QNC_SMBUS_DERR | B_QNC_SMBUS_BERR));
return RETURN_DEVICE_ERROR;
}
/**
Executes an SMBUS quick, byte or word command.
This internal function executes an SMBUS quick, byte or word commond.
If Status is not NULL, then the status of the executed command is returned in Status.
@param HostControl The value of Host Control Register to set.
@param SmBusAddress Address that encodes the SMBUS Slave Address,
SMBUS Command, SMBUS Data Length, and PEC.
@param Value The byte/word write to the SMBUS.
@param Status Return status for the executed command.
This is an optional parameter and may be NULL.
@return The byte/word read from the SMBUS.
**/
UINT16
InternalSmBusNonBlock (
IN UINT8 HostControl,
IN UINTN SmBusAddress,
IN UINT16 Value,
OUT RETURN_STATUS *Status
)
{
RETURN_STATUS ReturnStatus;
UINTN IoPortBaseAddress;
IoPortBaseAddress = InternalGetSmbusIoPortBaseAddress ();
//
// Try to acquire the ownership of QNC SMBUS.
//
ReturnStatus = InternalSmBusAcquire (IoPortBaseAddress);
if (RETURN_ERROR (ReturnStatus)) {
goto Done;
}
//
// Set Host Commond Register.
//
IoWrite8 (IoPortBaseAddress + R_QNC_SMBUS_HCMD, (UINT8) SMBUS_LIB_COMMAND (SmBusAddress));
//
// Write value to Host Data 0 and Host Data 1 Registers.
//
IoWrite8 (IoPortBaseAddress + R_QNC_SMBUS_HD0, (UINT8) Value);
IoWrite8 (IoPortBaseAddress + R_QNC_SMBUS_HD1, (UINT8) (Value >> 8));
//
// Set SMBUS slave address for the device to send/receive from.
//
IoWrite8 (IoPortBaseAddress + R_QNC_SMBUS_TSA, (UINT8) SmBusAddress);
//
// Start the SMBUS transaction and wait for the end.
//
ReturnStatus = InternalSmBusStart (IoPortBaseAddress, HostControl);
//
// Read value from Host Data 0 and Host Data 1 Registers.
//
Value = (UINT16)(IoRead8 (IoPortBaseAddress + R_QNC_SMBUS_HD1) << 8);
Value = (UINT16)(Value | IoRead8 (IoPortBaseAddress + R_QNC_SMBUS_HD0));
//
// Clear Host Status Register and Auxiliary Status Register.
//
IoWrite8 (IoPortBaseAddress + R_QNC_SMBUS_HSTS, B_QNC_SMBUS_HSTS_ALL);
Done:
if (Status != NULL) {
*Status = ReturnStatus;
}
return Value;
}
/**
Executes an SMBUS quick read command.
Executes an SMBUS quick read command on the SMBUS device specified by SmBusAddress.
Only the SMBUS slave address field of SmBusAddress is required.
If Status is not NULL, then the status of the executed command is returned in Status.
If PEC is set in SmBusAddress, then ASSERT().
If Command in SmBusAddress is not zero, then ASSERT().
If Length in SmBusAddress is not zero, then ASSERT().
If any reserved bits of SmBusAddress are set, then ASSERT().
@param SmBusAddress Address that encodes the SMBUS Slave Address,
SMBUS Command, SMBUS Data Length, and PEC.
@param Status Return status for the executed command.
This is an optional parameter and may be NULL.
**/
VOID
EFIAPI
SmBusQuickRead (
IN UINTN SmBusAddress,
OUT RETURN_STATUS *Status OPTIONAL
)
{
ASSERT (!SMBUS_LIB_PEC (SmBusAddress));
ASSERT (SMBUS_LIB_COMMAND (SmBusAddress) == 0);
ASSERT (SMBUS_LIB_LENGTH (SmBusAddress) == 0);
ASSERT (SMBUS_LIB_RESERVED (SmBusAddress) == 0);
InternalSmBusNonBlock (
V_QNC_SMBUS_HCTL_CMD_QUICK,
SmBusAddress | V_QNC_SMBUS_RW_SEL_READ,
0,
Status
);
}
/**
Executes an SMBUS quick write command.
Executes an SMBUS quick write command on the SMBUS device specified by SmBusAddress.
Only the SMBUS slave address field of SmBusAddress is required.
If Status is not NULL, then the status of the executed command is returned in Status.
If PEC is set in SmBusAddress, then ASSERT().
If Command in SmBusAddress is not zero, then ASSERT().
If Length in SmBusAddress is not zero, then ASSERT().
If any reserved bits of SmBusAddress are set, then ASSERT().
@param SmBusAddress Address that encodes the SMBUS Slave Address,
SMBUS Command, SMBUS Data Length, and PEC.
@param Status Return status for the executed command.
This is an optional parameter and may be NULL.
**/
VOID
EFIAPI
SmBusQuickWrite (
IN UINTN SmBusAddress,
OUT RETURN_STATUS *Status OPTIONAL
)
{
ASSERT (!SMBUS_LIB_PEC (SmBusAddress));
ASSERT (SMBUS_LIB_COMMAND (SmBusAddress) == 0);
ASSERT (SMBUS_LIB_LENGTH (SmBusAddress) == 0);
ASSERT (SMBUS_LIB_RESERVED (SmBusAddress) == 0);
InternalSmBusNonBlock (
V_QNC_SMBUS_HCTL_CMD_QUICK,
SmBusAddress & V_QNC_SMBUS_RW_SEL_WRITE,
0,
Status
);
}
/**
Executes an SMBUS receive byte command.
Executes an SMBUS receive byte command on the SMBUS device specified by SmBusAddress.
Only the SMBUS slave address field of SmBusAddress is required.
The byte received from the SMBUS is returned.
If Status is not NULL, then the status of the executed command is returned in Status.
If Command in SmBusAddress is not zero, then ASSERT().
If Length in SmBusAddress is not zero, then ASSERT().
If any reserved bits of SmBusAddress are set, then ASSERT().
@param SmBusAddress Address that encodes the SMBUS Slave Address,
SMBUS Command, SMBUS Data Length, and PEC.
@param Status Return status for the executed command.
This is an optional parameter and may be NULL.
@return The byte received from the SMBUS.
**/
UINT8
EFIAPI
SmBusReceiveByte (
IN UINTN SmBusAddress,
OUT RETURN_STATUS *Status OPTIONAL
)
{
ASSERT (SMBUS_LIB_COMMAND (SmBusAddress) == 0);
ASSERT (SMBUS_LIB_LENGTH (SmBusAddress) == 0);
ASSERT (SMBUS_LIB_RESERVED (SmBusAddress) == 0);
return (UINT8) InternalSmBusNonBlock (
V_QNC_SMBUS_HCTL_CMD_BYTE,
SmBusAddress | V_QNC_SMBUS_RW_SEL_READ,
0,
Status
);
}
/**
Executes an SMBUS send byte command.
Executes an SMBUS send byte command on the SMBUS device specified by SmBusAddress.
The byte specified by Value is sent.
Only the SMBUS slave address field of SmBusAddress is required. Value is returned.
If Status is not NULL, then the status of the executed command is returned in Status.
If Command in SmBusAddress is not zero, then ASSERT().
If Length in SmBusAddress is not zero, then ASSERT().
If any reserved bits of SmBusAddress are set, then ASSERT().
@param SmBusAddress Address that encodes the SMBUS Slave Address,
SMBUS Command, SMBUS Data Length, and PEC.
@param Value The 8-bit value to send.
@param Status Return status for the executed command.
This is an optional parameter and may be NULL.
@return The parameter of Value.
**/
UINT8
EFIAPI
SmBusSendByte (
IN UINTN SmBusAddress,
IN UINT8 Value,
OUT RETURN_STATUS *Status OPTIONAL
)
{
ASSERT (SMBUS_LIB_COMMAND (SmBusAddress) == 0);
ASSERT (SMBUS_LIB_LENGTH (SmBusAddress) == 0);
ASSERT (SMBUS_LIB_RESERVED (SmBusAddress) == 0);
return (UINT8) InternalSmBusNonBlock (
V_QNC_SMBUS_HCTL_CMD_BYTE,
SmBusAddress & V_QNC_SMBUS_RW_SEL_WRITE,
Value,
Status
);
}
/**
Executes an SMBUS read data byte command.
Executes an SMBUS read data byte command on the SMBUS device specified by SmBusAddress.
Only the SMBUS slave address and SMBUS command fields of SmBusAddress are required.
The 8-bit value read from the SMBUS is returned.
If Status is not NULL, then the status of the executed command is returned in Status.
If Length in SmBusAddress is not zero, then ASSERT().
If any reserved bits of SmBusAddress are set, then ASSERT().
@param SmBusAddress Address that encodes the SMBUS Slave Address,
SMBUS Command, SMBUS Data Length, and PEC.
@param Status Return status for the executed command.
This is an optional parameter and may be NULL.
@return The byte read from the SMBUS.
**/
UINT8
EFIAPI
SmBusReadDataByte (
IN UINTN SmBusAddress,
OUT RETURN_STATUS *Status OPTIONAL
)
{
ASSERT (SMBUS_LIB_LENGTH (SmBusAddress) == 0);
ASSERT (SMBUS_LIB_RESERVED (SmBusAddress) == 0);
return (UINT8) InternalSmBusNonBlock (
V_QNC_SMBUS_HCTL_CMD_BYTE_DATA,
SmBusAddress | V_QNC_SMBUS_RW_SEL_READ,
0,
Status
);
}
/**
Executes an SMBUS write data byte command.
Executes an SMBUS write data byte command on the SMBUS device specified by SmBusAddress.
The 8-bit value specified by Value is written.
Only the SMBUS slave address and SMBUS command fields of SmBusAddress are required.
Value is returned.
If Status is not NULL, then the status of the executed command is returned in Status.
If Length in SmBusAddress is not zero, then ASSERT().
If any reserved bits of SmBusAddress are set, then ASSERT().
@param SmBusAddress Address that encodes the SMBUS Slave Address,
SMBUS Command, SMBUS Data Length, and PEC.
@param Value The 8-bit value to write.
@param Status Return status for the executed command.
This is an optional parameter and may be NULL.
@return The parameter of Value.
**/
UINT8
EFIAPI
SmBusWriteDataByte (
IN UINTN SmBusAddress,
IN UINT8 Value,
OUT RETURN_STATUS *Status OPTIONAL
)
{
ASSERT (SMBUS_LIB_LENGTH (SmBusAddress) == 0);
ASSERT (SMBUS_LIB_RESERVED (SmBusAddress) == 0);
return (UINT8) InternalSmBusNonBlock (
V_QNC_SMBUS_HCTL_CMD_BYTE_DATA,
SmBusAddress | V_QNC_SMBUS_RW_SEL_WRITE,
Value,
Status
);
}
/**
Executes an SMBUS read data word command.
Executes an SMBUS read data word command on the SMBUS device specified by SmBusAddress.
Only the SMBUS slave address and SMBUS command fields of SmBusAddress are required.
The 16-bit value read from the SMBUS is returned.
If Status is not NULL, then the status of the executed command is returned in Status.
If Length in SmBusAddress is not zero, then ASSERT().
If any reserved bits of SmBusAddress are set, then ASSERT().
@param SmBusAddress Address that encodes the SMBUS Slave Address,
SMBUS Command, SMBUS Data Length, and PEC.
@param Status Return status for the executed command.
This is an optional parameter and may be NULL.
@return The byte read from the SMBUS.
**/
UINT16
EFIAPI
SmBusReadDataWord (
IN UINTN SmBusAddress,
OUT RETURN_STATUS *Status OPTIONAL
)
{
ASSERT (SMBUS_LIB_LENGTH (SmBusAddress) == 2);
ASSERT (SMBUS_LIB_RESERVED (SmBusAddress) == 0);
return InternalSmBusNonBlock (
V_QNC_SMBUS_HCTL_CMD_WORD_DATA,
SmBusAddress | V_QNC_SMBUS_RW_SEL_READ,
0,
Status
);
}
/**
Executes an SMBUS write data word command.
Executes an SMBUS write data word command on the SMBUS device specified by SmBusAddress.
The 16-bit value specified by Value is written.
Only the SMBUS slave address and SMBUS command fields of SmBusAddress are required.
Value is returned.
If Status is not NULL, then the status of the executed command is returned in Status.
If Length in SmBusAddress is not zero, then ASSERT().
If any reserved bits of SmBusAddress are set, then ASSERT().
@param SmBusAddress Address that encodes the SMBUS Slave Address,
SMBUS Command, SMBUS Data Length, and PEC.
@param Value The 16-bit value to write.
@param Status Return status for the executed command.
This is an optional parameter and may be NULL.
@return The parameter of Value.
**/
UINT16
EFIAPI
SmBusWriteDataWord (
IN UINTN SmBusAddress,
IN UINT16 Value,
OUT RETURN_STATUS *Status OPTIONAL
)
{
ASSERT (SMBUS_LIB_LENGTH (SmBusAddress) == 2);
ASSERT (SMBUS_LIB_RESERVED (SmBusAddress) == 0);
return InternalSmBusNonBlock (
V_QNC_SMBUS_HCTL_CMD_WORD_DATA,
SmBusAddress | V_QNC_SMBUS_RW_SEL_WRITE,
Value,
Status
);
}
/**
Executes an SMBUS process call command.
Executes an SMBUS process call command on the SMBUS device specified by SmBusAddress.
The 16-bit value specified by Value is written.
Only the SMBUS slave address and SMBUS command fields of SmBusAddress are required.
The 16-bit value returned by the process call command is returned.
If Status is not NULL, then the status of the executed command is returned in Status.
If Length in SmBusAddress is not zero, then ASSERT().
If any reserved bits of SmBusAddress are set, then ASSERT().
@param SmBusAddress Address that encodes the SMBUS Slave Address,
SMBUS Command, SMBUS Data Length, and PEC.
@param Value The 16-bit value to write.
@param Status Return status for the executed command.
This is an optional parameter and may be NULL.
@return The 16-bit value returned by the process call command.
**/
UINT16
EFIAPI
SmBusProcessCall (
IN UINTN SmBusAddress,
IN UINT16 Value,
OUT RETURN_STATUS *Status OPTIONAL
)
{
ASSERT (SMBUS_LIB_LENGTH (SmBusAddress) == 0);
ASSERT (SMBUS_LIB_RESERVED (SmBusAddress) == 0);
return InternalSmBusNonBlock (
V_QNC_SMBUS_HCTL_CMD_PROCESS_CALL,
SmBusAddress & V_QNC_SMBUS_RW_SEL_WRITE,
Value,
Status
);
}
/**
Executes an SMBUS block command.
Executes an SMBUS block read, block write and block write-block read command
on the SMBUS device specified by SmBusAddress.
Bytes are read from the SMBUS and stored in Buffer.
The number of bytes read is returned, and will never return a value larger than 32-bytes.
If Status is not NULL, then the status of the executed command is returned in Status.
It is the caller's responsibility to make sure Buffer is large enough for the total number of bytes read.
SMBUS supports a maximum transfer size of 32 bytes, so Buffer does not need to be any larger than 32 bytes.
@param HostControl The value of Host Control Register to set.
@param SmBusAddress Address that encodes the SMBUS Slave Address,
SMBUS Command, SMBUS Data Length, and PEC.
@param WriteBuffer Pointer to the buffer of bytes to write to the SMBUS.
@param ReadBuffer Pointer to the buffer of bytes to read from the SMBUS.
@param Status Return status for the executed command.
This is an optional parameter and may be NULL.
@return The number of bytes read from the SMBUS.
**/
UINTN
InternalSmBusBlock (
IN UINT8 HostControl,
IN UINTN SmBusAddress,
IN UINT8 *WriteBuffer,
OUT UINT8 *ReadBuffer,
OUT RETURN_STATUS *Status
)
{
RETURN_STATUS ReturnStatus;
UINTN Index;
UINTN BytesCount;
UINTN IoPortBaseAddress;
IoPortBaseAddress = InternalGetSmbusIoPortBaseAddress ();
BytesCount = SMBUS_LIB_LENGTH (SmBusAddress);
//
// Try to acquire the ownership of ICH SMBUS.
//
ReturnStatus = InternalSmBusAcquire (IoPortBaseAddress);
if (RETURN_ERROR (ReturnStatus)) {
goto Done;
}
//
// Set Host Command Register.
//
IoWrite8 (IoPortBaseAddress + R_QNC_SMBUS_HCMD, (UINT8) SMBUS_LIB_COMMAND (SmBusAddress));
//
// Clear byte pointer of 32-byte buffer.
//
IoRead8 (IoPortBaseAddress + R_QNC_SMBUS_HCTL);
if (WriteBuffer != NULL) {
//
// Write the number of block to Host Block Data Byte Register.
//
IoWrite8 (IoPortBaseAddress + R_QNC_SMBUS_HD0, (UINT8) BytesCount);
//
// Write data block to Host Block Data Register.
//
for (Index = 0; Index < BytesCount; Index++) {
IoWrite8 (IoPortBaseAddress + R_QNC_SMBUS_HBD + (UINT8)Index, WriteBuffer[Index]);
}
}
//
// Set SMBUS slave address for the device to send/receive from.
//
IoWrite8 (IoPortBaseAddress + R_QNC_SMBUS_TSA, (UINT8) SmBusAddress);
//
// Start the SMBUS transaction and wait for the end.
//
ReturnStatus = InternalSmBusStart (IoPortBaseAddress, HostControl);
if (RETURN_ERROR (ReturnStatus)) {
goto Done;
}
if (ReadBuffer != NULL) {
//
// Read the number of block from host block data byte register.
//
BytesCount = IoRead8 (IoPortBaseAddress + R_QNC_SMBUS_HD0);
//
// Write data block from Host Block Data Register.
//
for (Index = 0; Index < BytesCount; Index++) {
ReadBuffer[Index] = IoRead8 (IoPortBaseAddress + R_QNC_SMBUS_HBD + (UINT8)Index);
}
}
Done:
//
// Clear Host Status Register and Auxiliary Status Register.
//
IoWrite8 (IoPortBaseAddress + R_QNC_SMBUS_HSTS, B_QNC_SMBUS_HSTS_ALL);
if (Status != NULL) {
*Status = ReturnStatus;
}
return BytesCount;
}
/**
Executes an SMBUS read block command.
Executes an SMBUS read block command on the SMBUS device specified by SmBusAddress.
Only the SMBUS slave address and SMBUS command fields of SmBusAddress are required.
Bytes are read from the SMBUS and stored in Buffer.
The number of bytes read is returned, and will never return a value larger than 32-bytes.
If Status is not NULL, then the status of the executed command is returned in Status.
It is the caller's responsibility to make sure Buffer is large enough for the total number of bytes read.
SMBUS supports a maximum transfer size of 32 bytes, so Buffer does not need to be any larger than 32 bytes.
If Length in SmBusAddress is not zero, then ASSERT().
If Buffer is NULL, then ASSERT().
If any reserved bits of SmBusAddress are set, then ASSERT().
@param SmBusAddress Address that encodes the SMBUS Slave Address,
SMBUS Command, SMBUS Data Length, and PEC.
@param Buffer Pointer to the buffer to store the bytes read from the SMBUS.
@param Status Return status for the executed command.
This is an optional parameter and may be NULL.
@return The number of bytes read.
**/
UINTN
EFIAPI
SmBusReadBlock (
IN UINTN SmBusAddress,
OUT VOID *Buffer,
OUT RETURN_STATUS *Status OPTIONAL
)
{
ASSERT (Buffer != NULL);
ASSERT (SMBUS_LIB_LENGTH (SmBusAddress) >= 1);
ASSERT (SMBUS_LIB_LENGTH (SmBusAddress) <= 32);
ASSERT (SMBUS_LIB_RESERVED (SmBusAddress) == 0);
return InternalSmBusBlock (
V_QNC_SMBUS_HCTL_CMD_BLOCK,
SmBusAddress | V_QNC_SMBUS_RW_SEL_READ,
NULL,
Buffer,
Status
);
}
/**
Executes an SMBUS write block command.
Executes an SMBUS write block command on the SMBUS device specified by SmBusAddress.
The SMBUS slave address, SMBUS command, and SMBUS length fields of SmBusAddress are required.
Bytes are written to the SMBUS from Buffer.
The number of bytes written is returned, and will never return a value larger than 32-bytes.
If Status is not NULL, then the status of the executed command is returned in Status.
If Length in SmBusAddress is zero or greater than 32, then ASSERT().
If Buffer is NULL, then ASSERT().
If any reserved bits of SmBusAddress are set, then ASSERT().
@param SmBusAddress Address that encodes the SMBUS Slave Address,
SMBUS Command, SMBUS Data Length, and PEC.
@param Buffer Pointer to the buffer to store the bytes read from the SMBUS.
@param Status Return status for the executed command.
This is an optional parameter and may be NULL.
@return The number of bytes written.
**/
UINTN
EFIAPI
SmBusWriteBlock (
IN UINTN SmBusAddress,
OUT VOID *Buffer,
OUT RETURN_STATUS *Status OPTIONAL
)
{
ASSERT (Buffer != NULL);
ASSERT (SMBUS_LIB_LENGTH (SmBusAddress) >= 1);
ASSERT (SMBUS_LIB_LENGTH (SmBusAddress) <= 32);
ASSERT (SMBUS_LIB_RESERVED (SmBusAddress) == 0);
return InternalSmBusBlock (
V_QNC_SMBUS_HCTL_CMD_BLOCK,
SmBusAddress | V_QNC_SMBUS_RW_SEL_WRITE,
Buffer,
NULL,
Status
);
}
/**
Executes an SMBUS block process call command.
Executes an SMBUS block process call command on the SMBUS device specified by SmBusAddress.
The SMBUS slave address, SMBUS command, and SMBUS length fields of SmBusAddress are required.
Bytes are written to the SMBUS from WriteBuffer. Bytes are then read from the SMBUS into ReadBuffer.
If Status is not NULL, then the status of the executed command is returned in Status.
It is the caller's responsibility to make sure ReadBuffer is large enough for the total number of bytes read.
SMBUS supports a maximum transfer size of 32 bytes, so Buffer does not need to be any larger than 32 bytes.
If Length in SmBusAddress is zero or greater than 32, then ASSERT().
If WriteBuffer is NULL, then ASSERT().
If ReadBuffer is NULL, then ASSERT().
If any reserved bits of SmBusAddress are set, then ASSERT().
@param SmBusAddress Address that encodes the SMBUS Slave Address,
SMBUS Command, SMBUS Data Length, and PEC.
@param WriteBuffer Pointer to the buffer of bytes to write to the SMBUS.
@param ReadBuffer Pointer to the buffer of bytes to read from the SMBUS.
@param Status Return status for the executed command.
This is an optional parameter and may be NULL.
RETURN_TIMEOUT A timeout occurred while executing the SMBUS command.
RETURN_DEVICE_ERROR The request was not completed because a failure
reflected in the Host Status Register bit. Device errors are a result
of a transaction collision, illegal command field, unclaimed cycle
(host initiated), or bus errors (collisions).
RETURN_CRC_ERROR The checksum is not correct (PEC is incorrect)
RETURN_UNSUPPORTED The SMBus operation is not supported.
@return The number of bytes written.
**/
UINTN
EFIAPI
SmBusBlockProcessCall (
IN UINTN SmBusAddress,
IN VOID *WriteBuffer,
OUT VOID *ReadBuffer,
OUT RETURN_STATUS *Status OPTIONAL
)
{
ASSERT (WriteBuffer != NULL);
ASSERT (ReadBuffer != NULL);
ASSERT (SMBUS_LIB_LENGTH (SmBusAddress) >= 1);
ASSERT (SMBUS_LIB_LENGTH (SmBusAddress) <= 32);
ASSERT (SMBUS_LIB_RESERVED (SmBusAddress) == 0);
if (Status != NULL) {
*Status = RETURN_UNSUPPORTED;
}
return 0;
}