/** @file
* SMSC LAN91x series Network Controller Driver.
*
* Copyright (c) 2013 Linaro.org
*
* This program and the accompanying materials are licensed and
* made available under the terms and conditions of the BSD License
* which accompanies this distribution. The full text of the license
* may be found at: http://opensource.org/licenses/bsd-license.php
*
* THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
* WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
*
**/
#ifndef __LAN91XDXEHW_H__
#define __LAN91XDXEHW_H__
#include <Base.h>
#define MakeRegister(Bank, Offset) (((Bank) << 8) | (Offset))
#define RegisterToBank(Register) (((Register) >> 8) & 0x07)
#define RegisterToOffset(Register) ((Register) & 0x0f)
/*---------------------------------------------------------------------------------------------------------------------
SMSC LAN91x Registers
---------------------------------------------------------------------------------------------------------------------*/
#define LAN91X_BANK_OFFSET 0xe // Bank Select Register (all banks)
#define LAN91X_TCR MakeRegister (0, 0x0) // Transmit Control Register
#define LAN91X_EPHSR MakeRegister (0, 0x2) // EPH Status Register
#define LAN91X_RCR MakeRegister (0, 0x4) // Receive Control Register
#define LAN91X_ECR MakeRegister (0, 0x6) // Counter Register
#define LAN91X_MIR MakeRegister (0, 0x8) // Memory Information Register
#define LAN91X_RPCR MakeRegister (0, 0xa) // Receive/Phy Control Register
#define LAN91X_CR MakeRegister (1, 0x0) // Configuration Register
#define LAN91X_BAR MakeRegister (1, 0x2) // Base Address Register
#define LAN91X_IAR0 MakeRegister (1, 0x4) // Individual Address Register 0
#define LAN91X_IAR1 MakeRegister (1, 0x5) // Individual Address Register 1
#define LAN91X_IAR2 MakeRegister (1, 0x6) // Individual Address Register 2
#define LAN91X_IAR3 MakeRegister (1, 0x7) // Individual Address Register 3
#define LAN91X_IAR4 MakeRegister (1, 0x8) // Individual Address Register 4
#define LAN91X_IAR5 MakeRegister (1, 0x9) // Individual Address Register 5
#define LAN91X_GPR MakeRegister (1, 0xa) // General Purpose Register
#define LAN91X_CTR MakeRegister (1, 0xc) // Control Register
#define LAN91X_MMUCR MakeRegister (2, 0x0) // MMU Command Register
#define LAN91X_PNR MakeRegister (2, 0x2) // Packet Number Register
#define LAN91X_ARR MakeRegister (2, 0x3) // Allocation Result Register
#define LAN91X_FIFO MakeRegister (2, 0x4) // FIFO Ports Register
#define LAN91X_PTR MakeRegister (2, 0x6) // Pointer Register
#define LAN91X_DATA0 MakeRegister (2, 0x8) // Data Register 0
#define LAN91X_DATA1 MakeRegister (2, 0x9) // Data Register 1
#define LAN91X_DATA2 MakeRegister (2, 0xa) // Data Register 2
#define LAN91X_DATA3 MakeRegister (2, 0xb) // Data Register 3
#define LAN91X_IST MakeRegister (2, 0xc) // Interrupt Status Register
#define LAN91X_MSK MakeRegister (2, 0xd) // Interrupt Mask Register
#define LAN91X_MT0 MakeRegister (3, 0x0) // Multicast Table Register 0
#define LAN91X_MT1 MakeRegister (3, 0x1) // Multicast Table Register 1
#define LAN91X_MT2 MakeRegister (3, 0x2) // Multicast Table Register 2
#define LAN91X_MT3 MakeRegister (3, 0x3) // Multicast Table Register 3
#define LAN91X_MT4 MakeRegister (3, 0x4) // Multicast Table Register 4
#define LAN91X_MT5 MakeRegister (3, 0x5) // Multicast Table Register 5
#define LAN91X_MT6 MakeRegister (3, 0x6) // Multicast Table Register 6
#define LAN91X_MT7 MakeRegister (3, 0x7) // Multicast Table Register 7
#define LAN91X_MGMT MakeRegister (3, 0x8) // Management Interface Register
#define LAN91X_REV MakeRegister (3, 0xa) // Revision Register
#define LAN91X_RCV MakeRegister (3, 0xc) // RCV Register
// Transmit Control Register Bits
#define TCR_TXENA BIT0
#define TCR_LOOP BIT1
#define TCR_FORCOL BIT2
#define TCR_PAD_EN BIT7
#define TCR_NOCRC BIT8
#define TCR_MON_CSN BIT10
#define TCR_FDUPLX BIT11
#define TCR_STP_SQET BIT12
#define TCR_EPH_LOOP BIT13
#define TCR_SWFDUP BIT15
#define TCR_DEFAULT (TCR_TXENA | TCR_PAD_EN)
#define TCR_CLEAR 0x0
// EPH Status Register Bits
#define EPHSR_TX_SUC BIT0
#define EPHSR_SNGLCOL BIT1
#define EPHSR_MULCOL BIT2
#define EPHSR_LTX_MULT BIT3
#define EPHSR_16COL BIT4
#define EPHSR_SQET BIT5
#define EPHSR_LTX_BRD BIT6
#define EPHSR_TX_DEFR BIT7
#define EPHSR_LATCOL BIT9
#define EPHSR_LOST_CARR BIT10
#define EPHSR_EXC_DEF BIT11
#define EPHSR_CTR_ROL BIT12
#define EPHSR_LINK_OK BIT14
// Receive Control Register Bits
#define RCR_RX_ABORT BIT0
#define RCR_PRMS BIT1
#define RCR_ALMUL BIT2
#define RCR_RXEN BIT8
#define RCR_STRIP_CRC BIT9
#define RCR_ABORT_ENB BIT13
#define RCR_FILT_CAR BIT14
#define RCR_SOFT_RST BIT15
#define RCR_DEFAULT (RCR_STRIP_CRC | RCR_RXEN)
#define RCR_CLEAR 0x0
// Receive/Phy Control Register Bits
#define RPCR_LS0B BIT2
#define RPCR_LS1B BIT3
#define RPCR_LS2B BIT4
#define RPCR_LS0A BIT5
#define RPCR_LS1A BIT6
#define RPCR_LS2A BIT7
#define RPCR_ANEG BIT11
#define RPCR_DPLX BIT12
#define RPCR_SPEED BIT13
// Configuration Register Bits
#define CR_EXT_PHY BIT9
#define CR_GPCNTRL BIT10
#define CR_NO_WAIT BIT12
#define CR_EPH_POWER_EN BIT15
#define CR_DEFAULT (CR_EPH_POWER_EN | CR_NO_WAIT)
// Control Register Bits
#define CTR_STORE BIT0
#define CTR_RELOAD BIT1
#define CTR_EEPROM_SEL BIT2
#define CTR_TE_ENABLE BIT5
#define CTR_CR_ENABLE BIT6
#define CTR_LE_ENABLE BIT7
#define CTR_AUTO_REL BIT11
#define CTR_RCV_BAD BIT14
#define CTR_RESERVED (BIT12 | BIT9 | BIT4)
#define CTR_DEFAULT (CTR_RESERVED | CTR_AUTO_REL)
// MMU Command Register Bits
#define MMUCR_BUSY BIT0
// MMU Command Register Operaction Codes
#define MMUCR_OP_NOOP (0 << 5) // No operation
#define MMUCR_OP_TX_ALLOC (1 << 5) // Allocate memory for TX
#define MMUCR_OP_RESET_MMU (2 << 5) // Reset MMU to initial state
#define MMUCR_OP_RX_POP (3 << 5) // Remove frame from top of RX FIFO
#define MMUCR_OP_RX_POP_REL (4 << 5) // Remove and release frame from top of RX FIFO
#define MMUCR_OP_RX_REL (5 << 5) // Release specific RX frame
#define MMUCR_OP_TX_PUSH (6 << 5) // Enqueue packet number into TX FIFO
#define MMUCR_OP_TX_RESET (7 << 5) // Reset TX FIFOs
// Packet Number Register Bits
#define PNR_PACKET (0x3f)
// Allocation Result Register Bits
#define ARR_PACKET (0x3f)
#define ARR_FAILED BIT7
// FIFO Ports Register Bits
#define FIFO_TX_PACKET (0x003f)
#define FIFO_TEMPTY BIT7
#define FIFO_RX_PACKET (0x3f00)
#define FIFO_REMPTY BIT15
// Pointer Register Bits
#define PTR_POINTER (0x07ff)
#define PTR_NOT_EMPTY BIT11
#define PTR_READ BIT13
#define PTR_AUTO_INCR BIT14
#define PTR_RCV BIT15
// Interupt Status and Mask Register Bits
#define IST_RCV BIT0
#define IST_TX BIT1
#define IST_TX_EMPTY BIT2
#define IST_ALLOC BIT3
#define IST_RX_OVRN BIT4
#define IST_EPH BIT5
#define IST_MD BIT7
// Management Interface
#define MGMT_MDO BIT0
#define MGMT_MDI BIT1
#define MGMT_MCLK BIT2
#define MGMT_MDOE BIT3
#define MGMT_MSK_CRS100 BIT14
// RCV Register
#define RCV_MBO (0x1f)
#define RCV_RCV_DISCRD BIT7
// Packet RX Status word bits
#define RX_MULTICAST BIT0
#define RX_HASH (0x7e)
#define RX_TOO_SHORT BIT10
#define RX_TOO_LONG BIT11
#define RX_ODD_FRAME BIT12
#define RX_BAD_CRC BIT13
#define RX_BROADCAST BIT14
#define RX_ALGN_ERR BIT15
// Packet Byte Count word bits
#define BCW_COUNT (0x7fe)
// Packet Control Word bits
#define PCW_ODD_BYTE (0x00ff)
#define PCW_CRC BIT12
#define PCW_ODD BIT13
/*---------------------------------------------------------------------------------------------------------------------
SMSC PHY Registers
Most of these should be common, as there is
documented STANDARD for PHY registers!
---------------------------------------------------------------------------------------------------------------------*/
//
// PHY Register Numbers
//
#define PHY_INDEX_BASIC_CTRL 0
#define PHY_INDEX_BASIC_STATUS 1
#define PHY_INDEX_ID1 2
#define PHY_INDEX_ID2 3
#define PHY_INDEX_AUTO_NEG_ADVERT 4
#define PHY_INDEX_AUTO_NEG_LINK_ABILITY 5
#define PHY_INDEX_CONFIG1 16
#define PHY_INDEX_CONFIG2 17
#define PHY_INDEX_STATUS_OUTPUT 18
#define PHY_INDEX_MASK 19
// PHY control register bits
#define PHYCR_COLL_TEST BIT7 // Collision test enable
#define PHYCR_DUPLEX_MODE BIT8 // Set Duplex Mode
#define PHYCR_RST_AUTO BIT9 // Restart Auto-Negotiation of Link abilities
#define PHYCR_PD BIT11 // Power-Down switch
#define PHYCR_AUTO_EN BIT12 // Auto-Negotiation Enable
#define PHYCR_SPEED_SEL BIT13 // Link Speed Selection
#define PHYCR_LOOPBK BIT14 // Set loopback mode
#define PHYCR_RESET BIT15 // Do a PHY reset
// PHY status register bits
#define PHYSTS_EXT_CAP BIT0 // Extended Capabilities Register capability
#define PHYSTS_JABBER BIT1 // Jabber condition detected
#define PHYSTS_LINK_STS BIT2 // Link Status
#define PHYSTS_AUTO_CAP BIT3 // Auto-Negotiation Capability
#define PHYSTS_REMOTE_FAULT BIT4 // Remote fault detected
#define PHYSTS_AUTO_COMP BIT5 // Auto-Negotiation Completed
#define PHYSTS_10BASET_HDPLX BIT11 // 10Mbps Half-Duplex ability
#define PHYSTS_10BASET_FDPLX BIT12 // 10Mbps Full-Duplex ability
#define PHYSTS_100BASETX_HDPLX BIT13 // 100Mbps Half-Duplex ability
#define PHYSTS_100BASETX_FDPLX BIT14 // 100Mbps Full-Duplex ability
#define PHYSTS_100BASE_T4 BIT15 // Base T4 ability
// PHY Auto-Negotiation advertisement
#define PHYANA_SEL_MASK ((UINT32)0x1F) // Link type selector
#define PHYANA_CSMA BIT0 // Advertise CSMA capability
#define PHYANA_10BASET BIT5 // Advertise 10BASET capability
#define PHYANA_10BASETFD BIT6 // Advertise 10BASET Full duplex capability
#define PHYANA_100BASETX BIT7 // Advertise 100BASETX capability
#define PHYANA_100BASETXFD BIT8 // Advertise 100 BASETX Full duplex capability
#define PHYANA_100BASET4 BIT9 // Advertise 100 BASETX Full duplex capability
#define PHYANA_PAUSE_OP_MASK (3 << 10) // Advertise PAUSE frame capability
#define PHYANA_REMOTE_FAULT BIT13 // Remote fault detected
#endif /* __LAN91XDXEHW_H__ */