###############################################################################
# Firmware patch file
#  If the value is not set then patch download is disabled.
FW_PATCH="/vendor/firmware/bcm2079x-b5_firmware.ncd"

###############################################################################
# Firmware pre-patch file (sent before the above patch file)
#  If the value is not set then pre-patch is not used.
FW_PRE_PATCH="/vendor/firmware/bcm2079x-b5_pre_firmware.ncd"

###############################################################################
# LPTD mode configuration
#  byte[0] is the length of the remaining bytes in this value
#     if set to 0, LPTD params will NOT be sent to NFCC (i.e. disabled).
#  byte[1] is the param id it should be set to B9.
#  byte[2] is the length of the LPTD parameters
#  byte[3] indicates if LPTD is enabled
#     if set to 0, LPTD will be disabled (parameters will still be sent).
#  byte[4-n] are the LPTD parameters.
#  By default, LPTD is enabled and default settings are used.
#  See nfc_hal_dm_cfg.c for defaults
LPTD_CFG={38:B9:36:01:00:FF:FF:03:00:00:00:A0:0F:40:00:00:12:02:10:00:00:00:2D:0B:30:00:00:00:00:00:00:00:00:00:00:00:00:00:00:03:00:D0:07:00:00:08:07:00:00:C8:00:00:00:00:00:00:00}

###############################################################################
# Startup Configuration (256 bytes maximum)
#
# This is applied at stack startup.
NFA_DM_START_UP_CFG={42:CB:01:01:A5:01:01:CA:14:00:00:00:00:0E:C0:D4:01:00:0F:00:00:00:00:C0:C6:2D:00:14:0A:B5:03:01:02:FF:80:01:01:C9:03:03:0F:AB:5B:01:00:B2:04:E8:03:00:00:CF:02:02:08:B1:06:00:20:00:00:00:12:C2:02:01:C8}

# If NFA_DM_PRE_DISCOVERY_CFG is not supported by the current software, then this value should be used.
#NFA_DM_START_UP_CFG={48:CB:01:01:A5:01:01:CA:14:00:00:00:00:0E:C0:D4:01:00:0F:00:00:00:00:C0:C6:2D:00:14:0A:B5:03:01:03:FF:80:01:01:C9:03:03:0F:AB:5B:01:02:B2:04:E8:03:00:00:CF:02:02:08:B1:06:00:20:00:00:00:12:C2:08:01:08:00:04:80:C3:C9:01}

###############################################################################
# Pre-Discovery Startup Configuration (256 bytes maximum)
#
# This is applied before starting Discovery the first time.
NFA_DM_PRE_DISCOVERY_CFG={0A:C2:08:01:C8:00:04:40:4B:4C:00}

###############################################################################
# Antenna Configuration - This data is used when setting 0xC8 config item
# at startup (before discovery is started).  If not used, no value is sent.
#
# The settings for this value are documented here:
# http://wcgbu.broadcom.com/wpan/PM/Project%20Document%20Library/bcm20791B0/
#   Design/Doc/PHY%20register%20settings/BCM20791-B2-1027-02_PHY_Recommended_Reg_Settings.xlsx
#
# The values marked as ?? should be tweaked per antenna or customer/app:
# {20:C8:1E:06:??:00:??:??:??:00:??:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:??:01:00:00:40:04}
# array[0] = 0x20 is length of the payload from array[1] to the end
# array[1] = 0xC8 is PREINIT_DSP_CFG
PREINIT_DSP_CFG={20:C8:1E:06:3F:00:0A:03:30:00:04:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:4C:01:00:00:40:04}

###############################################################################
# Snooze Mode Settings
#
#  By default snooze mode is enabled.  Set SNOOZE_MODE_CFG byte[0] to 0
#  to disable.
#
#  If SNOOZE_MODE_CFG is not provided, the default settings are used:
#  They are as follows:
#       8             Sleep Mode (0=Disabled 1=UART 8=SPI/I2C)
#       0             Idle Threshold Host
#       0             Idle Threshold HC
#       0             NFC Wake active mode (0=ActiveLow 1=ActiveHigh)
#       1             Host Wake active mode (0=ActiveLow 1=ActiveHigh)
#
#SNOOZE_MODE_CFG={08:00:00:00:01}