// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2015 Freescale Semiconductor, Inc.
*
* Author: Fabio Estevam <fabio.estevam@freescale.com>
*
* Copyright (C) 2013 Jon Nettleton <jon.nettleton@gmail.com>
*
* Based on SPL code from Solidrun tree, which is:
* Author: Tungyi Lin <tungyilin1127@gmail.com>
*
* Derived from EDM_CF_IMX6 code by TechNexion,Inc
* Ported to SolidRun microSOM by Rabeeh Khoury <rabeeh@solid-run.com>
*/
#include <asm/arch/clock.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/iomux.h>
#include <asm/arch/mx6-pins.h>
#include <asm/arch/mxc_hdmi.h>
#include <linux/errno.h>
#include <asm/gpio.h>
#include <asm/mach-imx/iomux-v3.h>
#include <asm/mach-imx/sata.h>
#include <asm/mach-imx/video.h>
#include <mmc.h>
#include <fsl_esdhc.h>
#include <malloc.h>
#include <miiphy.h>
#include <netdev.h>
#include <asm/arch/crm_regs.h>
#include <asm/io.h>
#include <asm/arch/sys_proto.h>
#include <spl.h>
#include <usb.h>
#include <usb/ehci-ci.h>
DECLARE_GLOBAL_DATA_PTR;
#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
#define ENET_PAD_CTRL_PD (PAD_CTL_PUS_100K_DOWN | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
#define ENET_PAD_CTRL_CLK ((PAD_CTL_PUS_100K_UP & ~PAD_CTL_PKE) | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
#define ETH_PHY_RESET IMX_GPIO_NR(4, 15)
#define USB_H1_VBUS IMX_GPIO_NR(1, 0)
enum board_type {
CUBOXI = 0x00,
HUMMINGBOARD = 0x01,
HUMMINGBOARD2 = 0x02,
UNKNOWN = 0x03,
};
#define MEM_STRIDE 0x4000000
static u32 get_ram_size_stride_test(u32 *base, u32 maxsize)
{
volatile u32 *addr;
u32 save[64];
u32 cnt;
u32 size;
int i = 0;
/* First save the data */
for (cnt = 0; cnt < maxsize; cnt += MEM_STRIDE) {
addr = (volatile u32 *)((u32)base + cnt); /* pointer arith! */
sync ();
save[i++] = *addr;
sync ();
}
/* First write a signature */
* (volatile u32 *)base = 0x12345678;
for (size = MEM_STRIDE; size < maxsize; size += MEM_STRIDE) {
* (volatile u32 *)((u32)base + size) = size;
sync ();
if (* (volatile u32 *)((u32)base) == size) { /* We reached the overlapping address */
break;
}
}
/* Restore the data */
for (cnt = (maxsize - MEM_STRIDE); i > 0; cnt -= MEM_STRIDE) {
addr = (volatile u32 *)((u32)base + cnt); /* pointer arith! */
sync ();
*addr = save[i--];
sync ();
}
return (size);
}
int dram_init(void)
{
u32 max_size = imx_ddr_size();
gd->ram_size = get_ram_size_stride_test((u32 *) CONFIG_SYS_SDRAM_BASE,
(u32)max_size);
return 0;
}
static iomux_v3_cfg_t const uart1_pads[] = {
IOMUX_PADS(PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
IOMUX_PADS(PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
};
static iomux_v3_cfg_t const usdhc2_pads[] = {
IOMUX_PADS(PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
IOMUX_PADS(PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
};
static iomux_v3_cfg_t const board_detect[] = {
/* These pins are for sensing if it is a CuBox-i or a HummingBoard */
IOMUX_PADS(PAD_KEY_ROW1__GPIO4_IO09 | MUX_PAD_CTRL(UART_PAD_CTRL)),
IOMUX_PADS(PAD_EIM_DA4__GPIO3_IO04 | MUX_PAD_CTRL(UART_PAD_CTRL)),
IOMUX_PADS(PAD_SD4_DAT0__GPIO2_IO08 | MUX_PAD_CTRL(UART_PAD_CTRL)),
};
static iomux_v3_cfg_t const som_rev_detect[] = {
/* These pins are for sensing if it is a CuBox-i or a HummingBoard */
IOMUX_PADS(PAD_CSI0_DAT14__GPIO6_IO00 | MUX_PAD_CTRL(UART_PAD_CTRL)),
IOMUX_PADS(PAD_CSI0_DAT18__GPIO6_IO04 | MUX_PAD_CTRL(UART_PAD_CTRL)),
};
static iomux_v3_cfg_t const usb_pads[] = {
IOMUX_PADS(PAD_GPIO_0__GPIO1_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL)),
};
static void setup_iomux_uart(void)
{
SETUP_IOMUX_PADS(uart1_pads);
}
static struct fsl_esdhc_cfg usdhc_cfg[1] = {
{USDHC2_BASE_ADDR},
};
int board_mmc_getcd(struct mmc *mmc)
{
return 1; /* uSDHC2 is always present */
}
int board_mmc_init(bd_t *bis)
{
SETUP_IOMUX_PADS(usdhc2_pads);
usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR;
usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
}
static iomux_v3_cfg_t const enet_pads[] = {
IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL)),
IOMUX_PADS(PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
/* AR8035 reset */
IOMUX_PADS(PAD_KEY_ROW4__GPIO4_IO15 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD)),
/* AR8035 interrupt */
IOMUX_PADS(PAD_DI0_PIN2__GPIO4_IO18 | MUX_PAD_CTRL(NO_PAD_CTRL)),
/* GPIO16 -> AR8035 25MHz */
IOMUX_PADS(PAD_GPIO_16__ENET_REF_CLK | MUX_PAD_CTRL(NO_PAD_CTRL)),
IOMUX_PADS(PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(NO_PAD_CTRL)),
IOMUX_PADS(PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
IOMUX_PADS(PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
IOMUX_PADS(PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
IOMUX_PADS(PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
IOMUX_PADS(PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL)),
/* AR8035 CLK_25M --> ENET_REF_CLK (V22) */
IOMUX_PADS(PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL_CLK)),
IOMUX_PADS(PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
IOMUX_PADS(PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD)),
IOMUX_PADS(PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD)),
IOMUX_PADS(PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
IOMUX_PADS(PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
IOMUX_PADS(PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL_PD)),
IOMUX_PADS(PAD_ENET_RXD0__GPIO1_IO27 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD)),
IOMUX_PADS(PAD_ENET_RXD1__GPIO1_IO26 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD)),
};
static void setup_iomux_enet(void)
{
SETUP_IOMUX_PADS(enet_pads);
gpio_direction_output(ETH_PHY_RESET, 0);
mdelay(10);
gpio_set_value(ETH_PHY_RESET, 1);
udelay(100);
}
int board_phy_config(struct phy_device *phydev)
{
if (phydev->drv->config)
phydev->drv->config(phydev);
return 0;
}
/* On Cuboxi Ethernet PHY can be located at addresses 0x0 or 0x4 */
#define ETH_PHY_MASK ((1 << 0x0) | (1 << 0x4))
int board_eth_init(bd_t *bis)
{
struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
struct mii_dev *bus;
struct phy_device *phydev;
int ret = enable_fec_anatop_clock(0, ENET_25MHZ);
if (ret)
return ret;
/* set gpr1[ENET_CLK_SEL] */
setbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_ENET_CLK_SEL_MASK);
setup_iomux_enet();
bus = fec_get_miibus(IMX_FEC_BASE, -1);
if (!bus)
return -EINVAL;
phydev = phy_find_by_mask(bus, ETH_PHY_MASK, PHY_INTERFACE_MODE_RGMII);
if (!phydev) {
ret = -EINVAL;
goto free_bus;
}
debug("using phy at address %d\n", phydev->addr);
ret = fec_probe(bis, -1, IMX_FEC_BASE, bus, phydev);
if (ret)
goto free_phydev;
return 0;
free_phydev:
free(phydev);
free_bus:
free(bus);
return ret;
}
#ifdef CONFIG_VIDEO_IPUV3
static void do_enable_hdmi(struct display_info_t const *dev)
{
imx_enable_hdmi_phy();
}
struct display_info_t const displays[] = {
{
.bus = -1,
.addr = 0,
.pixfmt = IPU_PIX_FMT_RGB24,
.detect = detect_hdmi,
.enable = do_enable_hdmi,
.mode = {
.name = "HDMI",
/* 1024x768@60Hz (VESA)*/
.refresh = 60,
.xres = 1024,
.yres = 768,
.pixclock = 15384,
.left_margin = 160,
.right_margin = 24,
.upper_margin = 29,
.lower_margin = 3,
.hsync_len = 136,
.vsync_len = 6,
.sync = FB_SYNC_EXT,
.vmode = FB_VMODE_NONINTERLACED
}
}
};
size_t display_count = ARRAY_SIZE(displays);
static int setup_display(void)
{
struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
int reg;
int timeout = 100000;
enable_ipu_clock();
imx_setup_hdmi();
/* set video pll to 455MHz (24MHz * (37+11/12) / 2) */
setbits_le32(&ccm->analog_pll_video, BM_ANADIG_PLL_VIDEO_POWERDOWN);
reg = readl(&ccm->analog_pll_video);
reg &= ~BM_ANADIG_PLL_VIDEO_DIV_SELECT;
reg |= BF_ANADIG_PLL_VIDEO_DIV_SELECT(37);
reg &= ~BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT;
reg |= BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(1);
writel(reg, &ccm->analog_pll_video);
writel(BF_ANADIG_PLL_VIDEO_NUM_A(11), &ccm->analog_pll_video_num);
writel(BF_ANADIG_PLL_VIDEO_DENOM_B(12), &ccm->analog_pll_video_denom);
reg &= ~BM_ANADIG_PLL_VIDEO_POWERDOWN;
writel(reg, &ccm->analog_pll_video);
while (timeout--)
if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK)
break;
if (timeout < 0) {
printf("Warning: video pll lock timeout!\n");
return -ETIMEDOUT;
}
reg = readl(&ccm->analog_pll_video);
reg |= BM_ANADIG_PLL_VIDEO_ENABLE;
reg &= ~BM_ANADIG_PLL_VIDEO_BYPASS;
writel(reg, &ccm->analog_pll_video);
/* gate ipu1_di0_clk */
clrbits_le32(&ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK);
/* select video_pll clock / 7 for ipu1_di0_clk -> 65MHz pixclock */
reg = readl(&ccm->chsccdr);
reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK |
MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK |
MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK);
reg |= (2 << MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET) |
(6 << MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET) |
(0 << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
writel(reg, &ccm->chsccdr);
/* enable ipu1_di0_clk */
setbits_le32(&ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK);
return 0;
}
#endif /* CONFIG_VIDEO_IPUV3 */
#ifdef CONFIG_USB_EHCI_MX6
static void setup_usb(void)
{
SETUP_IOMUX_PADS(usb_pads);
}
int board_ehci_hcd_init(int port)
{
if (port == 1)
gpio_direction_output(USB_H1_VBUS, 1);
return 0;
}
#endif
int board_early_init_f(void)
{
setup_iomux_uart();
#ifdef CONFIG_CMD_SATA
setup_sata();
#endif
#ifdef CONFIG_USB_EHCI_MX6
setup_usb();
#endif
return 0;
}
int board_init(void)
{
int ret = 0;
/* address of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
#ifdef CONFIG_VIDEO_IPUV3
ret = setup_display();
#endif
return ret;
}
static enum board_type board_type(void)
{
int val1, val2, val3;
SETUP_IOMUX_PADS(board_detect);
/*
* Machine selection -
* Machine val1, val2, val3
* ----------------------------
* HB2 x x 0
* HB rev 3.x x 0 x
* CBi 0 1 x
* HB 1 1 x
*/
gpio_direction_input(IMX_GPIO_NR(2, 8));
val3 = gpio_get_value(IMX_GPIO_NR(2, 8));
if (val3 == 0)
return HUMMINGBOARD2;
gpio_direction_input(IMX_GPIO_NR(3, 4));
val2 = gpio_get_value(IMX_GPIO_NR(3, 4));
if (val2 == 0)
return HUMMINGBOARD;
gpio_direction_input(IMX_GPIO_NR(4, 9));
val1 = gpio_get_value(IMX_GPIO_NR(4, 9));
if (val1 == 0) {
return CUBOXI;
} else {
return HUMMINGBOARD;
}
}
static bool is_rev_15_som(void)
{
int val1, val2;
SETUP_IOMUX_PADS(som_rev_detect);
val1 = gpio_get_value(IMX_GPIO_NR(6, 0));
val2 = gpio_get_value(IMX_GPIO_NR(6, 4));
if (val1 == 1 && val2 == 0)
return true;
return false;
}
int checkboard(void)
{
switch (board_type()) {
case CUBOXI:
puts("Board: MX6 Cubox-i");
break;
case HUMMINGBOARD:
puts("Board: MX6 HummingBoard");
break;
case HUMMINGBOARD2:
puts("Board: MX6 HummingBoard2");
break;
case UNKNOWN:
default:
puts("Board: Unknown\n");
goto out;
}
if (is_rev_15_som())
puts(" (som rev 1.5)\n");
else
puts("\n");
out:
return 0;
}
int board_late_init(void)
{
#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
switch (board_type()) {
case CUBOXI:
env_set("board_name", "CUBOXI");
break;
case HUMMINGBOARD:
env_set("board_name", "HUMMINGBOARD");
break;
case HUMMINGBOARD2:
env_set("board_name", "HUMMINGBOARD2");
break;
case UNKNOWN:
default:
env_set("board_name", "CUBOXI");
}
if (is_mx6dq())
env_set("board_rev", "MX6Q");
else
env_set("board_rev", "MX6DL");
if (is_rev_15_som())
env_set("som_rev", "V15");
#endif
return 0;
}
#ifdef CONFIG_SPL_BUILD
#include <asm/arch/mx6-ddr.h>
static const struct mx6dq_iomux_ddr_regs mx6q_ddr_ioregs = {
.dram_sdclk_0 = 0x00020030,
.dram_sdclk_1 = 0x00020030,
.dram_cas = 0x00020030,
.dram_ras = 0x00020030,
.dram_reset = 0x000c0030,
.dram_sdcke0 = 0x00003000,
.dram_sdcke1 = 0x00003000,
.dram_sdba2 = 0x00000000,
.dram_sdodt0 = 0x00003030,
.dram_sdodt1 = 0x00003030,
.dram_sdqs0 = 0x00000030,
.dram_sdqs1 = 0x00000030,
.dram_sdqs2 = 0x00000030,
.dram_sdqs3 = 0x00000030,
.dram_sdqs4 = 0x00000030,
.dram_sdqs5 = 0x00000030,
.dram_sdqs6 = 0x00000030,
.dram_sdqs7 = 0x00000030,
.dram_dqm0 = 0x00020030,
.dram_dqm1 = 0x00020030,
.dram_dqm2 = 0x00020030,
.dram_dqm3 = 0x00020030,
.dram_dqm4 = 0x00020030,
.dram_dqm5 = 0x00020030,
.dram_dqm6 = 0x00020030,
.dram_dqm7 = 0x00020030,
};
static const struct mx6sdl_iomux_ddr_regs mx6dl_ddr_ioregs = {
.dram_sdclk_0 = 0x00000028,
.dram_sdclk_1 = 0x00000028,
.dram_cas = 0x00000028,
.dram_ras = 0x00000028,
.dram_reset = 0x000c0028,
.dram_sdcke0 = 0x00003000,
.dram_sdcke1 = 0x00003000,
.dram_sdba2 = 0x00000000,
.dram_sdodt0 = 0x00003030,
.dram_sdodt1 = 0x00003030,
.dram_sdqs0 = 0x00000028,
.dram_sdqs1 = 0x00000028,
.dram_sdqs2 = 0x00000028,
.dram_sdqs3 = 0x00000028,
.dram_sdqs4 = 0x00000028,
.dram_sdqs5 = 0x00000028,
.dram_sdqs6 = 0x00000028,
.dram_sdqs7 = 0x00000028,
.dram_dqm0 = 0x00000028,
.dram_dqm1 = 0x00000028,
.dram_dqm2 = 0x00000028,
.dram_dqm3 = 0x00000028,
.dram_dqm4 = 0x00000028,
.dram_dqm5 = 0x00000028,
.dram_dqm6 = 0x00000028,
.dram_dqm7 = 0x00000028,
};
static const struct mx6dq_iomux_grp_regs mx6q_grp_ioregs = {
.grp_ddr_type = 0x000C0000,
.grp_ddrmode_ctl = 0x00020000,
.grp_ddrpke = 0x00000000,
.grp_addds = 0x00000030,
.grp_ctlds = 0x00000030,
.grp_ddrmode = 0x00020000,
.grp_b0ds = 0x00000030,
.grp_b1ds = 0x00000030,
.grp_b2ds = 0x00000030,
.grp_b3ds = 0x00000030,
.grp_b4ds = 0x00000030,
.grp_b5ds = 0x00000030,
.grp_b6ds = 0x00000030,
.grp_b7ds = 0x00000030,
};
static const struct mx6sdl_iomux_grp_regs mx6sdl_grp_ioregs = {
.grp_ddr_type = 0x000c0000,
.grp_ddrmode_ctl = 0x00020000,
.grp_ddrpke = 0x00000000,
.grp_addds = 0x00000028,
.grp_ctlds = 0x00000028,
.grp_ddrmode = 0x00020000,
.grp_b0ds = 0x00000028,
.grp_b1ds = 0x00000028,
.grp_b2ds = 0x00000028,
.grp_b3ds = 0x00000028,
.grp_b4ds = 0x00000028,
.grp_b5ds = 0x00000028,
.grp_b6ds = 0x00000028,
.grp_b7ds = 0x00000028,
};
/* microSOM with Dual processor and 1GB memory */
static const struct mx6_mmdc_calibration mx6q_1g_mmcd_calib = {
.p0_mpwldectrl0 = 0x00000000,
.p0_mpwldectrl1 = 0x00000000,
.p1_mpwldectrl0 = 0x00000000,
.p1_mpwldectrl1 = 0x00000000,
.p0_mpdgctrl0 = 0x0314031c,
.p0_mpdgctrl1 = 0x023e0304,
.p1_mpdgctrl0 = 0x03240330,
.p1_mpdgctrl1 = 0x03180260,
.p0_mprddlctl = 0x3630323c,
.p1_mprddlctl = 0x3436283a,
.p0_mpwrdlctl = 0x36344038,
.p1_mpwrdlctl = 0x422a423c,
};
/* microSOM with Quad processor and 2GB memory */
static const struct mx6_mmdc_calibration mx6q_2g_mmcd_calib = {
.p0_mpwldectrl0 = 0x00000000,
.p0_mpwldectrl1 = 0x00000000,
.p1_mpwldectrl0 = 0x00000000,
.p1_mpwldectrl1 = 0x00000000,
.p0_mpdgctrl0 = 0x0314031c,
.p0_mpdgctrl1 = 0x023e0304,
.p1_mpdgctrl0 = 0x03240330,
.p1_mpdgctrl1 = 0x03180260,
.p0_mprddlctl = 0x3630323c,
.p1_mprddlctl = 0x3436283a,
.p0_mpwrdlctl = 0x36344038,
.p1_mpwrdlctl = 0x422a423c,
};
/* microSOM with Solo processor and 512MB memory */
static const struct mx6_mmdc_calibration mx6dl_512m_mmcd_calib = {
.p0_mpwldectrl0 = 0x0045004D,
.p0_mpwldectrl1 = 0x003A0047,
.p0_mpdgctrl0 = 0x023C0224,
.p0_mpdgctrl1 = 0x02000220,
.p0_mprddlctl = 0x44444846,
.p0_mpwrdlctl = 0x32343032,
};
/* microSOM with Dual lite processor and 1GB memory */
static const struct mx6_mmdc_calibration mx6dl_1g_mmcd_calib = {
.p0_mpwldectrl0 = 0x0045004D,
.p0_mpwldectrl1 = 0x003A0047,
.p1_mpwldectrl0 = 0x001F001F,
.p1_mpwldectrl1 = 0x00210035,
.p0_mpdgctrl0 = 0x023C0224,
.p0_mpdgctrl1 = 0x02000220,
.p1_mpdgctrl0 = 0x02200220,
.p1_mpdgctrl1 = 0x02040208,
.p0_mprddlctl = 0x44444846,
.p1_mprddlctl = 0x4042463C,
.p0_mpwrdlctl = 0x32343032,
.p1_mpwrdlctl = 0x36363430,
};
static struct mx6_ddr3_cfg mem_ddr_2g = {
.mem_speed = 1600,
.density = 2,
.width = 16,
.banks = 8,
.rowaddr = 14,
.coladdr = 10,
.pagesz = 2,
.trcd = 1375,
.trcmin = 4875,
.trasmin = 3500,
};
static struct mx6_ddr3_cfg mem_ddr_4g = {
.mem_speed = 1600,
.density = 4,
.width = 16,
.banks = 8,
.rowaddr = 16,
.coladdr = 10,
.pagesz = 2,
.trcd = 1375,
.trcmin = 4875,
.trasmin = 3500,
};
static void ccgr_init(void)
{
struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
writel(0x00C03F3F, &ccm->CCGR0);
writel(0x0030FC03, &ccm->CCGR1);
writel(0x0FFFC000, &ccm->CCGR2);
writel(0x3FF00000, &ccm->CCGR3);
writel(0x00FFF300, &ccm->CCGR4);
writel(0x0F0000C3, &ccm->CCGR5);
writel(0x000003FF, &ccm->CCGR6);
}
static void spl_dram_init(int width)
{
struct mx6_ddr_sysinfo sysinfo = {
/* width of data bus: 0=16, 1=32, 2=64 */
.dsize = width / 32,
/* config for full 4GB range so that get_mem_size() works */
.cs_density = 32, /* 32Gb per CS */
.ncs = 1, /* single chip select */
.cs1_mirror = 0,
.rtt_wr = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Wr = RZQ/4 */
.rtt_nom = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Nom = RZQ/4 */
.walat = 1, /* Write additional latency */
.ralat = 5, /* Read additional latency */
.mif3_mode = 3, /* Command prediction working mode */
.bi_on = 1, /* Bank interleaving enabled */
.sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
.rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
.ddr_type = DDR_TYPE_DDR3,
.refsel = 1, /* Refresh cycles at 32KHz */
.refr = 7, /* 8 refresh commands per refresh cycle */
};
if (is_mx6dq())
mx6dq_dram_iocfg(width, &mx6q_ddr_ioregs, &mx6q_grp_ioregs);
else
mx6sdl_dram_iocfg(width, &mx6dl_ddr_ioregs, &mx6sdl_grp_ioregs);
if (is_cpu_type(MXC_CPU_MX6D))
mx6_dram_cfg(&sysinfo, &mx6q_1g_mmcd_calib, &mem_ddr_2g);
else if (is_cpu_type(MXC_CPU_MX6Q))
mx6_dram_cfg(&sysinfo, &mx6q_2g_mmcd_calib, &mem_ddr_4g);
else if (is_cpu_type(MXC_CPU_MX6DL))
mx6_dram_cfg(&sysinfo, &mx6dl_1g_mmcd_calib, &mem_ddr_2g);
else if (is_cpu_type(MXC_CPU_MX6SOLO))
mx6_dram_cfg(&sysinfo, &mx6dl_512m_mmcd_calib, &mem_ddr_2g);
}
void board_init_f(ulong dummy)
{
/* setup AIPS and disable watchdog */
arch_cpu_init();
ccgr_init();
gpr_init();
/* iomux and setup of i2c */
board_early_init_f();
/* setup GP timer */
timer_init();
/* UART clocks enabled and gd valid - init serial console */
preloader_console_init();
/* DDR initialization */
if (is_cpu_type(MXC_CPU_MX6SOLO))
spl_dram_init(32);
else
spl_dram_init(64);
/* Clear the BSS. */
memset(__bss_start, 0, __bss_end - __bss_start);
/* load/boot image from boot device */
board_init_r(NULL, 0);
}
#endif