// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2004, 2011 Freescale Semiconductor.
*/
#include <common.h>
#include <pci.h>
#include <asm/processor.h>
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <fsl_ddr_sdram.h>
#include <ioports.h>
#include <spd_sdram.h>
#include <linux/libfdt.h>
#include <fdt_support.h>
#include "../common/cadmus.h"
#include "../common/eeprom.h"
#include "../common/via.h"
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
extern void ddr_enable_ecc(unsigned int dram_size);
#endif
void local_bus_init(void);
/*
* I/O Port configuration table
*
* if conf is 1, then that port pin will be configured at boot time
* according to the five values podr/pdir/ppar/psor/pdat for that entry
*/
const iop_conf_t iop_conf_tab[4][32] = {
/* Port A configuration */
{ /* conf ppar psor pdir podr pdat */
/* PA31 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 TxENB */
/* PA30 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 TxClav */
/* PA29 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 TxSOC */
/* PA28 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 RxENB */
/* PA27 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 RxSOC */
/* PA26 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 RxClav */
/* PA25 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[0] */
/* PA24 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[1] */
/* PA23 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[2] */
/* PA22 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[3] */
/* PA21 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[4] */
/* PA20 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[5] */
/* PA19 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[6] */
/* PA18 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[7] */
/* PA17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[7] */
/* PA16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[6] */
/* PA15 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[5] */
/* PA14 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[4] */
/* PA13 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[3] */
/* PA12 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[2] */
/* PA11 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[1] */
/* PA10 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[0] */
/* PA9 */ { 0, 1, 1, 1, 0, 0 }, /* FCC1 L1TXD */
/* PA8 */ { 0, 1, 1, 0, 0, 0 }, /* FCC1 L1RXD */
/* PA7 */ { 0, 0, 0, 1, 0, 0 }, /* PA7 */
/* PA6 */ { 0, 1, 1, 1, 0, 0 }, /* TDM A1 L1RSYNC */
/* PA5 */ { 0, 0, 0, 1, 0, 0 }, /* PA5 */
/* PA4 */ { 0, 0, 0, 1, 0, 0 }, /* PA4 */
/* PA3 */ { 0, 0, 0, 1, 0, 0 }, /* PA3 */
/* PA2 */ { 0, 0, 0, 1, 0, 0 }, /* PA2 */
/* PA1 */ { 1, 0, 0, 0, 0, 0 }, /* FREERUN */
/* PA0 */ { 0, 0, 0, 1, 0, 0 } /* PA0 */
},
/* Port B configuration */
{ /* conf ppar psor pdir podr pdat */
/* PB31 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TX_ER */
/* PB30 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_DV */
/* PB29 */ { 1, 1, 1, 1, 0, 0 }, /* FCC2 MII TX_EN */
/* PB28 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_ER */
/* PB27 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII COL */
/* PB26 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII CRS */
/* PB25 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[3] */
/* PB24 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[2] */
/* PB23 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[1] */
/* PB22 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[0] */
/* PB21 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[0] */
/* PB20 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[1] */
/* PB19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[2] */
/* PB18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[3] */
/* PB17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RX_DIV */
/* PB16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RX_ERR */
/* PB15 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TX_ERR */
/* PB14 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TX_EN */
/* PB13 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:COL */
/* PB12 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:CRS */
/* PB11 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
/* PB10 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
/* PB9 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
/* PB8 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
/* PB7 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
/* PB6 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
/* PB5 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
/* PB4 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
/* PB3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
/* PB2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
/* PB1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
/* PB0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */
},
/* Port C */
{ /* conf ppar psor pdir podr pdat */
/* PC31 */ { 0, 0, 0, 1, 0, 0 }, /* PC31 */
/* PC30 */ { 0, 0, 0, 1, 0, 0 }, /* PC30 */
/* PC29 */ { 0, 1, 1, 0, 0, 0 }, /* SCC1 EN *CLSN */
/* PC28 */ { 0, 0, 0, 1, 0, 0 }, /* PC28 */
/* PC27 */ { 0, 0, 0, 1, 0, 0 }, /* UART Clock in */
/* PC26 */ { 0, 0, 0, 1, 0, 0 }, /* PC26 */
/* PC25 */ { 0, 0, 0, 1, 0, 0 }, /* PC25 */
/* PC24 */ { 0, 0, 0, 1, 0, 0 }, /* PC24 */
/* PC23 */ { 0, 1, 0, 1, 0, 0 }, /* ATMTFCLK */
/* PC22 */ { 0, 1, 0, 0, 0, 0 }, /* ATMRFCLK */
/* PC21 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN RXCLK */
/* PC20 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN TXCLK */
/* PC19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_CLK CLK13 */
/* PC18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC Tx Clock (CLK14) */
/* PC17 */ { 0, 0, 0, 1, 0, 0 }, /* PC17 */
/* PC16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC Tx Clock (CLK16) */
/* PC15 */ { 1, 1, 0, 0, 0, 0 }, /* PC15 */
/* PC14 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN *CD */
/* PC13 */ { 0, 0, 0, 1, 0, 0 }, /* PC13 */
/* PC12 */ { 0, 1, 0, 1, 0, 0 }, /* PC12 */
/* PC11 */ { 0, 0, 0, 1, 0, 0 }, /* LXT971 transmit control */
/* PC10 */ { 1, 0, 0, 1, 0, 0 }, /* FETHMDC */
/* PC9 */ { 1, 0, 0, 0, 0, 0 }, /* FETHMDIO */
/* PC8 */ { 0, 0, 0, 1, 0, 0 }, /* PC8 */
/* PC7 */ { 0, 0, 0, 1, 0, 0 }, /* PC7 */
/* PC6 */ { 0, 0, 0, 1, 0, 0 }, /* PC6 */
/* PC5 */ { 0, 0, 0, 1, 0, 0 }, /* PC5 */
/* PC4 */ { 0, 0, 0, 1, 0, 0 }, /* PC4 */
/* PC3 */ { 0, 0, 0, 1, 0, 0 }, /* PC3 */
/* PC2 */ { 0, 0, 0, 1, 0, 1 }, /* ENET FDE */
/* PC1 */ { 0, 0, 0, 1, 0, 0 }, /* ENET DSQE */
/* PC0 */ { 0, 0, 0, 1, 0, 0 }, /* ENET LBK */
},
/* Port D */
{ /* conf ppar psor pdir podr pdat */
/* PD31 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN RxD */
/* PD30 */ { 1, 1, 1, 1, 0, 0 }, /* SCC1 EN TxD */
/* PD29 */ { 1, 1, 0, 1, 0, 0 }, /* SCC1 EN TENA */
/* PD28 */ { 0, 1, 0, 0, 0, 0 }, /* PD28 */
/* PD27 */ { 0, 1, 1, 1, 0, 0 }, /* PD27 */
/* PD26 */ { 0, 0, 0, 1, 0, 0 }, /* PD26 */
/* PD25 */ { 0, 0, 0, 1, 0, 0 }, /* PD25 */
/* PD24 */ { 0, 0, 0, 1, 0, 0 }, /* PD24 */
/* PD23 */ { 0, 0, 0, 1, 0, 0 }, /* PD23 */
/* PD22 */ { 0, 0, 0, 1, 0, 0 }, /* PD22 */
/* PD21 */ { 0, 0, 0, 1, 0, 0 }, /* PD21 */
/* PD20 */ { 0, 0, 0, 1, 0, 0 }, /* PD20 */
/* PD19 */ { 0, 0, 0, 1, 0, 0 }, /* PD19 */
/* PD18 */ { 0, 0, 0, 1, 0, 0 }, /* PD18 */
/* PD17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXPRTY */
/* PD16 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXPRTY */
/* PD15 */ { 0, 1, 1, 0, 1, 0 }, /* I2C SDA */
/* PD14 */ { 0, 0, 0, 1, 0, 0 }, /* LED */
/* PD13 */ { 0, 0, 0, 0, 0, 0 }, /* PD13 */
/* PD12 */ { 0, 0, 0, 0, 0, 0 }, /* PD12 */
/* PD11 */ { 0, 0, 0, 0, 0, 0 }, /* PD11 */
/* PD10 */ { 0, 0, 0, 0, 0, 0 }, /* PD10 */
/* PD9 */ { 0, 1, 0, 1, 0, 0 }, /* SMC1 TXD */
/* PD8 */ { 0, 1, 0, 0, 0, 0 }, /* SMC1 RXD */
/* PD7 */ { 0, 0, 0, 1, 0, 1 }, /* PD7 */
/* PD6 */ { 0, 0, 0, 1, 0, 1 }, /* PD6 */
/* PD5 */ { 0, 0, 0, 1, 0, 1 }, /* PD5 */
/* PD4 */ { 0, 0, 0, 1, 0, 1 }, /* PD4 */
/* PD3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
/* PD2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
/* PD1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
/* PD0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */
}
};
int checkboard (void)
{
volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
char buf[32];
/* PCI slot in USER bits CSR[6:7] by convention. */
uint pci_slot = get_pci_slot ();
uint pci_dual = get_pci_dual (); /* PCI DUAL in CM_PCI[3] */
uint pci1_32 = gur->pordevsr & 0x10000; /* PORDEVSR[15] */
uint pci1_clk_sel = gur->porpllsr & 0x8000; /* PORPLLSR[16] */
uint pci2_clk_sel = gur->porpllsr & 0x4000; /* PORPLLSR[17] */
uint pci1_speed = get_clock_freq (); /* PCI PSPEED in [4:5] */
uint cpu_board_rev = get_cpu_board_revision ();
printf ("Board: CDS Version 0x%02x, PCI Slot %d\n",
get_board_version (), pci_slot);
printf ("CPU Board Revision %d.%d (0x%04x)\n",
MPC85XX_CPU_BOARD_MAJOR (cpu_board_rev),
MPC85XX_CPU_BOARD_MINOR (cpu_board_rev), cpu_board_rev);
printf("PCI1: %d bit, %s MHz, %s\n",
(pci1_32) ? 32 : 64,
strmhz(buf, pci1_speed),
pci1_clk_sel ? "sync" : "async");
if (pci_dual) {
printf("PCI2: 32 bit, 66 MHz, %s\n",
pci2_clk_sel ? "sync" : "async");
} else {
printf("PCI2: disabled\n");
}
/*
* Initialize local bus.
*/
local_bus_init ();
return 0;
}
/*
* Initialize Local Bus
*/
void
local_bus_init(void)
{
volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
uint clkdiv;
uint lbc_hz;
sys_info_t sysinfo;
uint temp_lbcdll;
/*
* Errata LBC11.
* Fix Local Bus clock glitch when DLL is enabled.
*
* If localbus freq is < 66MHz, DLL bypass mode must be used.
* If localbus freq is > 133MHz, DLL can be safely enabled.
* Between 66 and 133, the DLL is enabled with an override workaround.
*/
get_sys_info(&sysinfo);
clkdiv = lbc->lcrr & LCRR_CLKDIV;
lbc_hz = sysinfo.freq_systembus / 1000000 / clkdiv;
if (lbc_hz < 66) {
lbc->lcrr |= LCRR_DBYP; /* DLL Bypass */
} else if (lbc_hz >= 133) {
lbc->lcrr &= (~LCRR_DBYP); /* DLL Enabled */
} else {
lbc->lcrr &= (~LCRR_DBYP); /* DLL Enabled */
udelay(200);
/*
* Sample LBC DLL ctrl reg, upshift it to set the
* override bits.
*/
temp_lbcdll = gur->lbcdllcr;
gur->lbcdllcr = (((temp_lbcdll & 0xff) << 16) | 0x80000000);
asm("sync;isync;msync");
}
}
/*
* Initialize SDRAM memory on the Local Bus.
*/
void lbc_sdram_init(void)
{
#if defined(CONFIG_SYS_OR2_PRELIM) && defined(CONFIG_SYS_BR2_PRELIM)
uint idx;
volatile fsl_lbc_t *lbc = LBC_BASE_ADDR;
uint *sdram_addr = (uint *)CONFIG_SYS_LBC_SDRAM_BASE;
uint cpu_board_rev;
uint lsdmr_common;
puts("LBC SDRAM: ");
print_size(CONFIG_SYS_LBC_SDRAM_SIZE * 1024 * 1024,
"\n ");
/*
* Setup SDRAM Base and Option Registers
*/
set_lbc_or(2, CONFIG_SYS_OR2_PRELIM);
set_lbc_br(2, CONFIG_SYS_BR2_PRELIM);
lbc->lbcr = CONFIG_SYS_LBC_LBCR;
asm("msync");
lbc->lsrt = CONFIG_SYS_LBC_LSRT;
lbc->mrtpr = CONFIG_SYS_LBC_MRTPR;
asm("msync");
/*
* Determine which address lines to use baed on CPU board rev.
*/
cpu_board_rev = get_cpu_board_revision();
lsdmr_common = CONFIG_SYS_LBC_LSDMR_COMMON;
if (cpu_board_rev == MPC85XX_CPU_BOARD_REV_1_0) {
lsdmr_common |= LSDMR_BSMA1617;
} else if (cpu_board_rev == MPC85XX_CPU_BOARD_REV_1_1) {
lsdmr_common |= LSDMR_BSMA1516;
} else {
/*
* Assume something unable to identify itself is
* really old, and likely has lines 16/17 mapped.
*/
lsdmr_common |= LSDMR_BSMA1617;
}
/*
* Issue PRECHARGE ALL command.
*/
lbc->lsdmr = lsdmr_common | LSDMR_OP_PCHALL;
asm("sync;msync");
*sdram_addr = 0xff;
ppcDcbf((unsigned long) sdram_addr);
udelay(100);
/*
* Issue 8 AUTO REFRESH commands.
*/
for (idx = 0; idx < 8; idx++) {
lbc->lsdmr = lsdmr_common | LSDMR_OP_ARFRSH;
asm("sync;msync");
*sdram_addr = 0xff;
ppcDcbf((unsigned long) sdram_addr);
udelay(100);
}
/*
* Issue 8 MODE-set command.
*/
lbc->lsdmr = lsdmr_common | LSDMR_OP_MRW;
asm("sync;msync");
*sdram_addr = 0xff;
ppcDcbf((unsigned long) sdram_addr);
udelay(100);
/*
* Issue NORMAL OP command.
*/
lbc->lsdmr = lsdmr_common | LSDMR_OP_NORMAL;
asm("sync;msync");
*sdram_addr = 0xff;
ppcDcbf((unsigned long) sdram_addr);
udelay(200); /* Overkill. Must wait > 200 bus cycles */
#endif /* enable SDRAM init */
}
#ifdef CONFIG_PCI
/* For some reason the Tundra PCI bridge shows up on itself as a
* different device. Work around that by refusing to configure it
*/
void dummy_func(struct pci_controller* hose, pci_dev_t dev, struct pci_config_table *tab) { }
static struct pci_config_table pci_mpc85xxcds_config_table[] = {
{0x10e3, 0x0513, PCI_ANY_ID, 1, 3, PCI_ANY_ID, dummy_func, {0,0,0}},
{0x1106, 0x0686, PCI_ANY_ID, 1, VIA_ID, 0, mpc85xx_config_via, {0,0,0}},
{0x1106, 0x0571, PCI_ANY_ID, 1, VIA_ID, 1,
mpc85xx_config_via_usbide, {0,0,0}},
{0x1105, 0x3038, PCI_ANY_ID, 1, VIA_ID, 2,
mpc85xx_config_via_usb, {0,0,0}},
{0x1106, 0x3038, PCI_ANY_ID, 1, VIA_ID, 3,
mpc85xx_config_via_usb2, {0,0,0}},
{0x1106, 0x3058, PCI_ANY_ID, 1, VIA_ID, 5,
mpc85xx_config_via_power, {0,0,0}},
{0x1106, 0x3068, PCI_ANY_ID, 1, VIA_ID, 6,
mpc85xx_config_via_ac97, {0,0,0}},
{},
};
static struct pci_controller hose[] = {
{
config_table: pci_mpc85xxcds_config_table,
},
#ifdef CONFIG_MPC85XX_PCI2
{},
#endif
};
#endif
void
pci_init_board(void)
{
#ifdef CONFIG_PCI
pci_mpc85xx_init(hose);
#endif
}
#if defined(CONFIG_OF_BOARD_SETUP)
void
ft_pci_setup(void *blob, bd_t *bd)
{
int node, tmp[2];
const char *path;
node = fdt_path_offset(blob, "/aliases");
tmp[0] = 0;
if (node >= 0) {
#ifdef CONFIG_PCI1
path = fdt_getprop(blob, node, "pci0", NULL);
if (path) {
tmp[1] = hose[0].last_busno - hose[0].first_busno;
do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1);
}
#endif
#ifdef CONFIG_MPC85XX_PCI2
path = fdt_getprop(blob, node, "pci1", NULL);
if (path) {
tmp[1] = hose[1].last_busno - hose[1].first_busno;
do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1);
}
#endif
}
}
#endif