/*
* Qualcomm Atheros OUI and vendor specific assignments
* Copyright (c) 2014-2017, Qualcomm Atheros, Inc.
* Copyright (c) 2018, The Linux Foundation
*
* This software may be distributed under the terms of the BSD license.
* See README for more details.
*/
#ifndef QCA_VENDOR_H
#define QCA_VENDOR_H
/*
* This file is a registry of identifier assignments from the Qualcomm Atheros
* OUI 00:13:74 for purposes other than MAC address assignment. New identifiers
* can be assigned through normal review process for changes to the upstream
* hostap.git repository.
*/
#define OUI_QCA 0x001374
/**
* enum qca_radiotap_vendor_ids - QCA radiotap vendor namespace IDs
*/
enum qca_radiotap_vendor_ids {
QCA_RADIOTAP_VID_WLANTEST = 0,
};
/**
* enum qca_nl80211_vendor_subcmds - QCA nl80211 vendor command identifiers
*
* @QCA_NL80211_VENDOR_SUBCMD_UNSPEC: Reserved value 0
*
* @QCA_NL80211_VENDOR_SUBCMD_TEST: Test command/event
*
* @QCA_NL80211_VENDOR_SUBCMD_ROAMING: Set roaming policy for drivers that use
* internal BSS-selection. This command uses
* @QCA_WLAN_VENDOR_ATTR_ROAMING_POLICY to specify the new roaming policy
* for the current connection (i.e., changes policy set by the nl80211
* Connect command). @QCA_WLAN_VENDOR_ATTR_MAC_ADDR may optionally be
* included to indicate which BSS to use in case roaming is disabled.
*
* @QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY: Recommendation of frequency
* ranges to avoid to reduce issues due to interference or internal
* co-existence information in the driver. These frequencies aim to
* minimize the traffic but not to totally avoid the traffic. That said
* for a P2P use case, these frequencies are allowed for the P2P
* discovery/negotiation but avoid the group to get formed on these
* frequencies. The event data structure is defined in
* struct qca_avoid_freq_list.
*
* @QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY: Command to check driver support
* for DFS offloading.
*
* @QCA_NL80211_VENDOR_SUBCMD_NAN: NAN command/event which is used to pass
* NAN Request/Response and NAN Indication messages. These messages are
* interpreted between the framework and the firmware component. While
* sending the command from userspace to the driver, payload is not
* encapsulated inside any attribute. Attribute QCA_WLAN_VENDOR_ATTR_NAN
* is used when receiving vendor events in userspace from the driver.
*
* @QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_SET_KEY: Set key operation that can be
* used to configure PMK to the driver even when not connected. This can
* be used to request offloading of key management operations. Only used
* if device supports QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD.
*
* @QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH: An extended version of
* NL80211_CMD_ROAM event with optional attributes including information
* from offloaded key management operation. Uses
* enum qca_wlan_vendor_attr_roam_auth attributes. Only used
* if device supports QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD.
*
* @QCA_NL80211_VENDOR_SUBCMD_DO_ACS: ACS command/event which is used to
* invoke the ACS function in device and pass selected channels to
* hostapd.
*
* @QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES: Command to get the features
* supported by the driver. enum qca_wlan_vendor_features defines
* the possible features.
*
* @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_STARTED: Event used by driver,
* which supports DFS offloading, to indicate a channel availability check
* start.
*
* @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_FINISHED: Event used by driver,
* which supports DFS offloading, to indicate a channel availability check
* completion.
*
* @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_ABORTED: Event used by driver,
* which supports DFS offloading, to indicate that the channel availability
* check aborted, no change to the channel status.
*
* @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_NOP_FINISHED: Event used by
* driver, which supports DFS offloading, to indicate that the
* Non-Occupancy Period for this channel is over, channel becomes usable.
*
* @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED: Event used by driver,
* which supports DFS offloading, to indicate a radar pattern has been
* detected. The channel is now unusable.
*
* @QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET: Get the feature bitmap
* based on enum wifi_logger_supported_features. Attributes defined in
* enum qca_wlan_vendor_attr_get_logger_features.
*
* @QCA_NL80211_VENDOR_SUBCMD_GET_RING_DATA: Get the ring data from a particular
* logger ring, QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_RING_ID is passed as the
* attribute for this command. Attributes defined in
* enum qca_wlan_vendor_attr_wifi_logger_start.
*
* @QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_CAPABILITIES: Get the supported TDLS
* capabilities of the driver, parameters includes the attributes defined
* in enum qca_wlan_vendor_attr_tdls_get_capabilities.
*
* @QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS: Vendor command used to offload
* sending of certain periodic IP packet to firmware, attributes defined in
* enum qca_wlan_vendor_attr_offloaded_packets.
*
* @QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI: Command used to configure RSSI
* monitoring, defines min and max RSSI which are configured for RSSI
* monitoring. Also used to notify the RSSI breach and provides the BSSID
* and RSSI value that was breached. Attributes defined in
* enum qca_wlan_vendor_attr_rssi_monitoring.
*
* @QCA_NL80211_VENDOR_SUBCMD_NDP: Command used for performing various NAN
* Data Path (NDP) related operations, attributes defined in
* enum qca_wlan_vendor_attr_ndp_params.
*
* @QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD: Command used to enable/disable
* Neighbour Discovery offload, attributes defined in
* enum qca_wlan_vendor_attr_nd_offload.
*
* @QCA_NL80211_VENDOR_SUBCMD_PACKET_FILTER: Used to set/get the various
* configuration parameter for BPF packet filter, attributes defined in
* enum qca_wlan_vendor_attr_packet_filter.
*
* @QCA_NL80211_VENDOR_SUBCMD_GET_BUS_SIZE: Gets the driver-firmware
* maximum supported size, attributes defined in
* enum qca_wlan_vendor_drv_info.
*
* @QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS: Command to get various
* data about wake reasons and datapath IP statistics, attributes defined
* in enum qca_wlan_vendor_attr_wake_stats.
*
* @QCA_NL80211_VENDOR_SUBCMD_OCB_SET_CONFIG: Command used to set configuration
* for IEEE 802.11 communicating outside the context of a basic service
* set, called OCB command. Uses the attributes defines in
* enum qca_wlan_vendor_attr_ocb_set_config.
*
* @QCA_NL80211_VENDOR_SUBCMD_OCB_SET_UTC_TIME: Command used to set OCB
* UTC time. Use the attributes defines in
* enum qca_wlan_vendor_attr_ocb_set_utc_time.
*
* @QCA_NL80211_VENDOR_SUBCMD_OCB_START_TIMING_ADVERT: Command used to start
* sending OCB timing advert frames. Uses the attributes defines in
* enum qca_wlan_vendor_attr_ocb_start_timing_advert.
*
* @QCA_NL80211_VENDOR_SUBCMD_OCB_STOP_TIMING_ADVERT: Command used to stop
* OCB timing advert. Uses the attributes defines in
* enum qca_wlan_vendor_attr_ocb_stop_timing_advert.
*
* @QCA_NL80211_VENDOR_SUBCMD_OCB_GET_TSF_TIMER: Command used to get TSF
* timer value. Uses the attributes defines in
* enum qca_wlan_vendor_attr_ocb_get_tsf_resp.
*
* @QCA_NL80211_VENDOR_SUBCMD_LINK_PROPERTIES: Command/event to update the
* link properties of the respective interface. As an event, is used
* to notify the connected station's status. The attributes for this
* command are defined in enum qca_wlan_vendor_attr_link_properties.
*
* @QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START: Command used to
* start the P2P Listen offload function in device and pass the listen
* channel, period, interval, count, device types, and vendor specific
* information elements to the device driver and firmware.
* Uses the attributes defines in
* enum qca_wlan_vendor_attr_p2p_listen_offload.
*
* @QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP: Command/event used to
* indicate stop request/response of the P2P Listen offload function in
* device. As an event, it indicates either the feature stopped after it
* was already running or feature has actually failed to start. Uses the
* attributes defines in enum qca_wlan_vendor_attr_p2p_listen_offload.
*
* @QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH: After AP starts
* beaconing, this sub command provides the driver, the frequencies on the
* 5 GHz band to check for any radar activity. Driver selects one channel
* from this priority list provided through
* @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST and starts
* to check for radar activity on it. If no radar activity is detected
* during the channel availability check period, driver internally switches
* to the selected frequency of operation. If the frequency is zero, driver
* internally selects a channel. The status of this conditional switch is
* indicated through an event using the same sub command through
* @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS. Attributes are
* listed in qca_wlan_vendor_attr_sap_conditional_chan_switch.
*
* @QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND: Set GPIO pins. This uses the
* attributes defined in enum qca_wlan_gpio_attr.
*
* @QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY: Fetch hardware capabilities.
* This uses @QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY to indicate which
* capabilities are to be fetched and other
* enum qca_wlan_vendor_attr_get_hw_capability attributes to return the
* requested capabilities.
*
* @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT: Link layer statistics extension.
* enum qca_wlan_vendor_attr_ll_stats_ext attributes are used with this
* command and event.
*
* @QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA: Get capabilities for
* indoor location features. Capabilities are reported in
* QCA_WLAN_VENDOR_ATTR_LOC_CAPA.
*
* @QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION: Start an FTM
* (fine timing measurement) session with one or more peers.
* Specify Session cookie in QCA_WLAN_VENDOR_ATTR_FTM_SESSION_COOKIE and
* peer information in QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEERS.
* On success, 0 or more QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT
* events will be reported, followed by
* QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE event to indicate
* end of session.
* Refer to IEEE P802.11-REVmc/D7.0, 11.24.6
*
* @QCA_NL80211_VENDOR_SUBCMD_FTM_ABORT_SESSION: Abort a running session.
* A QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE will be reported with
* status code indicating session was aborted.
*
* @QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT: Event with measurement
* results for one peer. Results are reported in
* QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEER_RESULTS.
*
* @QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE: Event triggered when
* FTM session is finished, either successfully or aborted by
* request.
*
* @QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER: Configure FTM responder
* mode. QCA_WLAN_VENDOR_ATTR_FTM_RESPONDER_ENABLE specifies whether
* to enable or disable the responder. LCI/LCR reports can be
* configured with QCA_WLAN_VENDOR_ATTR_FTM_LCI and
* QCA_WLAN_VENDOR_ATTR_FTM_LCR. Can be called multiple
* times to update the LCI/LCR reports.
*
* @QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS: Perform a standalone AOA (angle of
* arrival) measurement with a single peer. Specify peer MAC address in
* QCA_WLAN_VENDOR_ATTR_MAC_ADDR and optionally frequency (MHz) in
* QCA_WLAN_VENDOR_ATTR_FREQ (if not specified, locate peer in kernel
* scan results cache and use the frequency from there).
* Also specify measurement type in QCA_WLAN_VENDOR_ATTR_AOA_TYPE.
* Measurement result is reported in
* QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT event.
*
* @QCA_NL80211_VENDOR_SUBCMD_AOA_ABORT_MEAS: Abort an AOA measurement. Specify
* peer MAC address in QCA_WLAN_VENDOR_ATTR_MAC_ADDR.
*
* @QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT: Event that reports
* the AOA measurement result.
* Peer MAC address reported in QCA_WLAN_VENDOR_ATTR_MAC_ADDR.
* success/failure status is reported in
* QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS.
* Measurement data is reported in QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT.
* The antenna array(s) used in the measurement are reported in
* QCA_WLAN_VENDOR_ATTR_LOC_ANTENNA_ARRAY_MASK.
*
* @QCA_NL80211_VENDOR_SUBCMD_ENCRYPTION_TEST: Encrypt/decrypt the given
* data as per the given parameters.
*
* @QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI: Get antenna RSSI value for a
* specific chain.
*
* @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG: Get low level
* configuration for a DMG RF sector. Specify sector index in
* QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX, sector type in
* QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE and RF modules
* to return sector information for in
* QCA_WLAN_VENDOR_ATTR_DMG_RF_MODULE_MASK. Returns sector configuration
* in QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG. Also return the
* exact time where information was captured in
* QCA_WLAN_VENDOR_ATTR_TSF.
*
* @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG: Set low level
* configuration for a DMG RF sector. Specify sector index in
* QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX, sector type in
* QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE and sector configuration
* for one or more DMG RF modules in
* QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG.
*
* @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SELECTED_SECTOR: Get selected
* DMG RF sector for a station. This is the sector that the HW
* will use to communicate with the station. Specify the MAC address
* of associated station/AP/PCP in QCA_WLAN_VENDOR_ATTR_MAC_ADDR (not
* needed for unassociated station). Specify sector type to return in
* QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE. Returns the selected
* sector index in QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX.
* Also return the exact time where the information was captured
* in QCA_WLAN_VENDOR_ATTR_TSF.
*
* @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR: Set the
* selected DMG RF sector for a station. This is the sector that
* the HW will use to communicate with the station.
* Specify the MAC address of associated station/AP/PCP in
* QCA_WLAN_VENDOR_ATTR_MAC_ADDR, the sector type to select in
* QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE and the sector index
* in QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX.
* The selected sector will be locked such that it will not be
* modified like it normally does (for example when station
* moves around). To unlock the selected sector for a station
* pass the special value 0xFFFF in the sector index. To unlock
* all connected stations also pass a broadcast MAC address.
*
* @QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS: Configure the TDLS behavior
* in the host driver. The different TDLS configurations are defined
* by the attributes in enum qca_wlan_vendor_attr_tdls_configuration.
*
* @QCA_NL80211_VENDOR_SUBCMD_GET_HE_CAPABILITIES: Query device IEEE 802.11ax HE
* capabilities. The response uses the attributes defined in
* enum qca_wlan_vendor_attr_get_he_capabilities.
*
* @QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN: Abort an ongoing vendor scan that was
* started with QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN. This command
* carries the scan cookie of the corresponding scan request. The scan
* cookie is represented by QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE.
*
* @QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS: Set the Specific
* Absorption Rate (SAR) power limits. A critical regulation for
* FCC compliance, OEMs require methods to set SAR limits on TX
* power of WLAN/WWAN. enum qca_vendor_attr_sar_limits
* attributes are used with this command.
*
* @QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS: This command/event is used by the
* host driver for offloading the implementation of Auto Channel Selection
* (ACS) to an external user space entity. This interface is used as the
* event from the host driver to the user space entity and also as the
* request from the user space entity to the host driver. The event from
* the host driver is used by the user space entity as an indication to
* start the ACS functionality. The attributes used by this event are
* represented by the enum qca_wlan_vendor_attr_external_acs_event.
* User space entity uses the same interface to inform the host driver with
* selected channels after the ACS operation using the attributes defined
* by enum qca_wlan_vendor_attr_external_acs_channels.
*
* @QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE: Vendor event carrying the
* requisite information leading to a power save failure. The information
* carried as part of this event is represented by the
* enum qca_attr_chip_power_save_failure attributes.
*
* @QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET: Start/Stop the NUD statistics
* collection. Uses attributes defined in enum qca_attr_nud_stats_set.
*
* @QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET: Get the NUD statistics. These
* statistics are represented by the enum qca_attr_nud_stats_get
* attributes.
*
* @QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS: Sub-command to fetch
* the BSS transition status, whether accept or reject, for a list of
* candidate BSSIDs provided by the userspace. This uses the vendor
* attributes QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON and
* QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO. The userspace shall specify
* the attributes QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON and an
* array of QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID nested in
* QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO in the request. In the response
* the driver shall specify array of
* QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID and
* QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_STATUS pairs nested in
* QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO.
*
* @QCA_NL80211_VENDOR_SUBCMD_SET_TRACE_LEVEL: Set the trace level for a
* specific QCA module. The trace levels are represented by
* enum qca_attr_trace_level attributes.
*
* @QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT: Set the Beam Refinement
* Protocol antenna limit in different modes. See enum
* qca_wlan_vendor_attr_brp_ant_limit_mode.
*
* @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START: Start spectral scan. The scan
* parameters are specified by enum qca_wlan_vendor_attr_spectral_scan.
* This returns a cookie (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE)
* identifying the operation in success case.
*
* @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP: Stop spectral scan. This uses
* a cookie (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE) from
* @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START to identify the scan to
* be stopped.
*
* @QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS: Set the active Type Of Service on the
* specific interface. This can be used to modify some of the low level
* scan parameters (off channel dwell time, home channel time) in the
* driver/firmware. These parameters are maintained within the host driver.
* This command is valid only when the interface is in the connected state.
* These scan parameters shall be reset by the driver/firmware once
* disconnected. The attributes used with this command are defined in
* enum qca_wlan_vendor_attr_active_tos.
*
* @QCA_NL80211_VENDOR_SUBCMD_HANG: Event indicating to the user space that the
* driver has detected an internal failure. This event carries the
* information indicating the reason that triggered this detection. The
* attributes for this command are defined in
* enum qca_wlan_vendor_attr_hang.
*
* @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CONFIG: Get the current values
* of spectral parameters used. The spectral scan parameters are specified
* by enum qca_wlan_vendor_attr_spectral_scan.
*
* @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS: Get the debug stats
* for spectral scan functionality. The debug stats are specified by
* enum qca_wlan_vendor_attr_spectral_diag_stats.
*
* @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO: Get spectral
* scan system capabilities. The capabilities are specified
* by enum qca_wlan_vendor_attr_spectral_cap.
*
* @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS: Get the current
* status of spectral scan. The status values are specified
* by enum qca_wlan_vendor_attr_spectral_scan_status.
*
* @QCA_NL80211_VENDOR_SUBCMD_PEER_FLUSH_PENDING: Sub-command to flush
* peer pending packets. Specify the peer MAC address in
* QCA_WLAN_VENDOR_ATTR_PEER_ADDR and the access category of the packets
* in QCA_WLAN_VENDOR_ATTR_AC. The attributes are listed
* in enum qca_wlan_vendor_attr_flush_pending.
*
* @QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO: Get vendor specific Representative
* RF Operating Parameter (RROP) information. The attributes for this
* information are defined in enum qca_wlan_vendor_attr_rrop_info. This is
* intended for use by external Auto Channel Selection applications.
*
* @QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS: Get the Specific Absorption Rate
* (SAR) power limits. This is a companion to the command
* @QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS and is used to retrieve the
* settings currently in use. The attributes returned by this command are
* defined by enum qca_vendor_attr_sar_limits.
*
* @QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO: Provides the current behavior of
* the WLAN hardware MAC. Also, provides the WLAN netdev interface
* information attached to the respective MAC.
* This works both as a query (user space asks the current mode) or event
* interface (driver advertising the current mode to the user space).
* Driver does not trigger this event for temporary hardware mode changes.
* Mode changes w.r.t Wi-Fi connection update (VIZ creation / deletion,
* channel change, etc.) are updated with this event. Attributes for this
* interface are defined in enum qca_wlan_vendor_attr_mac.
*
* @QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH: Set MSDU queue depth threshold
* per peer per TID. Attributes for this command are define in
* enum qca_wlan_set_qdepth_thresh_attr.
* @QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD: Provides the thermal shutdown action
* guide for WLAN driver. Request to suspend of driver and FW if the
* temperature is higher than the suspend threshold; resume action is
* requested to driver if the temperature is lower than the resume
* threshold. In user poll mode, request temperature data by user. For test
* purpose, getting thermal shutdown configuration parameters is needed.
* Attributes for this interface are defined in
* enum qca_wlan_vendor_attr_thermal_cmd.
* @QCA_NL80211_VENDOR_SUBCMD_THERMAL_EVENT: Thermal events reported from
* driver. Thermal temperature and indication of resume completion are
* reported as thermal events. The attributes for this command are defined
* in enum qca_wlan_vendor_attr_thermal_event.
*
* @QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION: Sub command to set WiFi
* test configuration. Attributes for this command are defined in
* enum qca_wlan_vendor_attr_wifi_test_config.
*
* @QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER: This command is used to configure an
* RX filter to receive frames from stations that are active on the
* operating channel, but not associated with the local device (e.g., STAs
* associated with other APs). Filtering is done based on a list of BSSIDs
* and STA MAC addresses added by the user. This command is also used to
* fetch the statistics of unassociated stations. The attributes used with
* this command are defined in enum qca_wlan_vendor_attr_bss_filter.
*
* @QCA_NL80211_VENDOR_SUBCMD_NAN_EXT: An extendable version of NAN vendor
* command. The earlier command for NAN, QCA_NL80211_VENDOR_SUBCMD_NAN,
* carried a payload which was a binary blob of data. The command was not
* extendable to send more information. The newer version carries the
* legacy blob encapsulated within an attribute and can be extended with
* additional vendor attributes that can enhance the NAN command interface.
* @QCA_NL80211_VENDOR_SUBCMD_ROAM_SCAN_EVENT: Event to indicate scan triggered
* or stopped within driver/firmware in order to initiate roaming. The
* attributes used with this event are defined in enum
* qca_wlan_vendor_attr_roam_scan. Some drivers may not send these events
* in few cases, e.g., if the host processor is sleeping when this event
* is generated in firmware.
*
* @QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG: This command is used to
* configure parameters per peer to capture Channel Frequency Response
* (CFR) and enable Periodic CFR capture. The attributes for this command
* are defined in enum qca_wlan_vendor_peer_cfr_capture_attr.
*
* @QCA_NL80211_VENDOR_SUBCMD_THROUGHPUT_CHANGE_EVENT: Event to indicate changes
* in throughput dynamically. The driver estimates the throughput based on
* number of packets being transmitted/received per second and indicates
* the changes in throughput to user space. Userspace tools can use this
* information to configure kernel's TCP parameters in order to achieve
* peak throughput. Optionally, the driver will also send guidance on
* modifications to kernel's TCP parameters which can be referred by
* userspace tools. The attributes used with this event are defined in enum
* qca_wlan_vendor_attr_throughput_change.
*
* @QCA_NL80211_VENDOR_SUBCMD_COEX_CONFIG: This command is used to set
* priorities among different types of traffic during coex scenarios.
* Current supported prioritization is among WLAN/BT/ZIGBEE with different
* profiles mentioned in enum qca_coex_config_profiles. The associated
* attributes used with this command are defined in enum
* qca_vendor_attr_coex_config.
*
* Based on the config provided, FW will boost the weight and prioritize
* the traffic for that subsystem (WLAN/BT/Zigbee).
*
* @QCA_NL80211_VENDOR_SUBCMD_GET_SUPPORTED_AKMS: This command is used to query
* the supported AKM suite selectorss from the driver. It returns the list
* of supported AKMs in the attribute NL80211_ATTR_AKM_SUITES.
* @QCA_NL80211_VENDOR_SUBCMD_GET_FW_STATE: This command is used to get firmware
* state from the driver. It returns the firmware state in the attribute
* QCA_WLAN_VENDOR_ATTR_FW_STATE.
* @QCA_NL80211_VENDOR_SUBCMD_PEER_STATS_CACHE_FLUSH: This vendor subcommand
* is used by the driver to flush per-peer cached statistics to user space
* application. This interface is used as an event from the driver to
* user space application. Attributes for this event are specified in
* enum qca_wlan_vendor_attr_peer_stats_cache_params.
* QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_DATA attribute is expected to be
* sent in the event.
* @QCA_NL80211_VENDOR_SUBCMD_MPTA_HELPER_CONFIG: This sub command is used to
* improve the success rate of Zigbee joining network.
* Due to PTA master limitation, Zigbee joining network success rate is
* low while WLAN is working. The WLAN driver needs to configure some
* parameters including Zigbee state and specific WLAN periods to enhance
* PTA master. All these parameters are delivered by the attributes
* defined in enum qca_mpta_helper_vendor_attr.
*/
enum qca_nl80211_vendor_subcmds {
QCA_NL80211_VENDOR_SUBCMD_UNSPEC = 0,
QCA_NL80211_VENDOR_SUBCMD_TEST = 1,
/* subcmds 2..8 not yet allocated */
QCA_NL80211_VENDOR_SUBCMD_ROAMING = 9,
QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY = 10,
QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY = 11,
QCA_NL80211_VENDOR_SUBCMD_NAN = 12,
QCA_NL80211_VENDOR_SUBCMD_STATS_EXT = 13,
QCA_NL80211_VENDOR_SUBCMD_LL_STATS_SET = 14,
QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET = 15,
QCA_NL80211_VENDOR_SUBCMD_LL_STATS_CLR = 16,
QCA_NL80211_VENDOR_SUBCMD_LL_STATS_RADIO_RESULTS = 17,
QCA_NL80211_VENDOR_SUBCMD_LL_STATS_IFACE_RESULTS = 18,
QCA_NL80211_VENDOR_SUBCMD_LL_STATS_PEERS_RESULTS = 19,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_START = 20,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_STOP = 21,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_VALID_CHANNELS = 22,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CAPABILITIES = 23,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CACHED_RESULTS = 24,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_RESULTS_AVAILABLE = 25,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_FULL_SCAN_RESULT = 26,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_EVENT = 27,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_FOUND = 28,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_BSSID_HOTLIST = 29,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_BSSID_HOTLIST = 30,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_SIGNIFICANT_CHANGE = 31,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SIGNIFICANT_CHANGE = 32,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_SIGNIFICANT_CHANGE = 33,
QCA_NL80211_VENDOR_SUBCMD_TDLS_ENABLE = 34,
QCA_NL80211_VENDOR_SUBCMD_TDLS_DISABLE = 35,
QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_STATUS = 36,
QCA_NL80211_VENDOR_SUBCMD_TDLS_STATE = 37,
QCA_NL80211_VENDOR_SUBCMD_GET_SUPPORTED_FEATURES = 38,
QCA_NL80211_VENDOR_SUBCMD_SCANNING_MAC_OUI = 39,
QCA_NL80211_VENDOR_SUBCMD_NO_DFS_FLAG = 40,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_LOST = 41,
QCA_NL80211_VENDOR_SUBCMD_GET_CONCURRENCY_MATRIX = 42,
/* 43..49 - reserved for QCA */
QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_SET_KEY = 50,
QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH = 51,
QCA_NL80211_VENDOR_SUBCMD_APFIND = 52,
/* 53 - reserved - was used by QCA, but not in use anymore */
QCA_NL80211_VENDOR_SUBCMD_DO_ACS = 54,
QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES = 55,
QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_STARTED = 56,
QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_FINISHED = 57,
QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_ABORTED = 58,
QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_NOP_FINISHED = 59,
QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED = 60,
QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO = 61,
QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_START = 62,
QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_MEMORY_DUMP = 63,
QCA_NL80211_VENDOR_SUBCMD_ROAM = 64,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SSID_HOTLIST = 65,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_SSID_HOTLIST = 66,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_SSID_FOUND = 67,
QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_SSID_LOST = 68,
QCA_NL80211_VENDOR_SUBCMD_PNO_SET_LIST = 69,
QCA_NL80211_VENDOR_SUBCMD_PNO_SET_PASSPOINT_LIST = 70,
QCA_NL80211_VENDOR_SUBCMD_PNO_RESET_PASSPOINT_LIST = 71,
QCA_NL80211_VENDOR_SUBCMD_PNO_NETWORK_FOUND = 72,
QCA_NL80211_VENDOR_SUBCMD_PNO_PASSPOINT_NETWORK_FOUND = 73,
/* Wi-Fi configuration subcommands */
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION = 74,
QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION = 75,
QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET = 76,
QCA_NL80211_VENDOR_SUBCMD_GET_RING_DATA = 77,
QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_CAPABILITIES = 78,
QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS = 79,
QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI = 80,
QCA_NL80211_VENDOR_SUBCMD_NDP = 81,
QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD = 82,
QCA_NL80211_VENDOR_SUBCMD_PACKET_FILTER = 83,
QCA_NL80211_VENDOR_SUBCMD_GET_BUS_SIZE = 84,
QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS = 85,
/* 86-90 - reserved for QCA */
QCA_NL80211_VENDOR_SUBCMD_DATA_OFFLOAD = 91,
QCA_NL80211_VENDOR_SUBCMD_OCB_SET_CONFIG = 92,
QCA_NL80211_VENDOR_SUBCMD_OCB_SET_UTC_TIME = 93,
QCA_NL80211_VENDOR_SUBCMD_OCB_START_TIMING_ADVERT = 94,
QCA_NL80211_VENDOR_SUBCMD_OCB_STOP_TIMING_ADVERT = 95,
QCA_NL80211_VENDOR_SUBCMD_OCB_GET_TSF_TIMER = 96,
QCA_NL80211_VENDOR_SUBCMD_DCC_GET_STATS = 97,
QCA_NL80211_VENDOR_SUBCMD_DCC_CLEAR_STATS = 98,
QCA_NL80211_VENDOR_SUBCMD_DCC_UPDATE_NDL = 99,
QCA_NL80211_VENDOR_SUBCMD_DCC_STATS_EVENT = 100,
QCA_NL80211_VENDOR_SUBCMD_LINK_PROPERTIES = 101,
QCA_NL80211_VENDOR_SUBCMD_GW_PARAM_CONFIG = 102,
QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST = 103,
QCA_NL80211_VENDOR_SUBCMD_SET_PROBABLE_OPER_CHANNEL = 104,
QCA_NL80211_VENDOR_SUBCMD_SETBAND = 105,
QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN = 106,
QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE = 107,
QCA_NL80211_VENDOR_SUBCMD_OTA_TEST = 108,
QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_SCALE = 109,
/* 110..114 - reserved for QCA */
QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_DECR_DB = 115,
/* 116..117 - reserved for QCA */
QCA_NL80211_VENDOR_SUBCMD_SET_SAP_CONFIG = 118,
QCA_NL80211_VENDOR_SUBCMD_TSF = 119,
QCA_NL80211_VENDOR_SUBCMD_WISA = 120,
/* 121 - reserved for QCA */
QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START = 122,
QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP = 123,
QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH = 124,
QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND = 125,
QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY = 126,
QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT = 127,
/* FTM/indoor location subcommands */
QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA = 128,
QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION = 129,
QCA_NL80211_VENDOR_SUBCMD_FTM_ABORT_SESSION = 130,
QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT = 131,
QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE = 132,
QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER = 133,
QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS = 134,
QCA_NL80211_VENDOR_SUBCMD_AOA_ABORT_MEAS = 135,
QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT = 136,
QCA_NL80211_VENDOR_SUBCMD_ENCRYPTION_TEST = 137,
QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI = 138,
/* DMG low level RF sector operations */
QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG = 139,
QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG = 140,
QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SELECTED_SECTOR = 141,
QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR = 142,
QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS = 143,
QCA_NL80211_VENDOR_SUBCMD_GET_HE_CAPABILITIES = 144,
QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN = 145,
QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS = 146,
QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS = 147,
QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE = 148,
QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET = 149,
QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET = 150,
QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS = 151,
QCA_NL80211_VENDOR_SUBCMD_SET_TRACE_LEVEL = 152,
QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT = 153,
QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START = 154,
QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP = 155,
QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS = 156,
QCA_NL80211_VENDOR_SUBCMD_HANG = 157,
QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CONFIG = 158,
QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS = 159,
QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO = 160,
QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS = 161,
/* Flush peer pending data */
QCA_NL80211_VENDOR_SUBCMD_PEER_FLUSH_PENDING = 162,
QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO = 163,
QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS = 164,
QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO = 165,
QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH = 166,
/* Thermal shutdown commands to protect wifi chip */
QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD = 167,
QCA_NL80211_VENDOR_SUBCMD_THERMAL_EVENT = 168,
/* Wi-Fi test configuration subcommand */
QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION = 169,
/* Frame filter operations for other BSSs/unassociated STAs */
QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER = 170,
QCA_NL80211_VENDOR_SUBCMD_NAN_EXT = 171,
QCA_NL80211_VENDOR_SUBCMD_ROAM_SCAN_EVENT = 172,
QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG = 173,
QCA_NL80211_VENDOR_SUBCMD_THROUGHPUT_CHANGE_EVENT = 174,
QCA_NL80211_VENDOR_SUBCMD_COEX_CONFIG = 175,
QCA_NL80211_VENDOR_SUBCMD_GET_SUPPORTED_AKMS = 176,
QCA_NL80211_VENDOR_SUBCMD_GET_FW_STATE = 177,
QCA_NL80211_VENDOR_SUBCMD_PEER_STATS_CACHE_FLUSH = 178,
QCA_NL80211_VENDOR_SUBCMD_MPTA_HELPER_CONFIG = 179,
};
enum qca_wlan_vendor_attr {
QCA_WLAN_VENDOR_ATTR_INVALID = 0,
/* used by QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY */
QCA_WLAN_VENDOR_ATTR_DFS = 1,
/* Used only when driver sends vendor events to the userspace under the
* command QCA_NL80211_VENDOR_SUBCMD_NAN. Not used when userspace sends
* commands to the driver.
*/
QCA_WLAN_VENDOR_ATTR_NAN = 2,
/* used by QCA_NL80211_VENDOR_SUBCMD_STATS_EXT */
QCA_WLAN_VENDOR_ATTR_STATS_EXT = 3,
/* used by QCA_NL80211_VENDOR_SUBCMD_STATS_EXT */
QCA_WLAN_VENDOR_ATTR_IFINDEX = 4,
/* used by QCA_NL80211_VENDOR_SUBCMD_ROAMING, u32 with values defined
* by enum qca_roaming_policy.
*/
QCA_WLAN_VENDOR_ATTR_ROAMING_POLICY = 5,
QCA_WLAN_VENDOR_ATTR_MAC_ADDR = 6,
/* used by QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES */
QCA_WLAN_VENDOR_ATTR_FEATURE_FLAGS = 7,
QCA_WLAN_VENDOR_ATTR_TEST = 8,
/* used by QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES */
/* Unsigned 32-bit value. */
QCA_WLAN_VENDOR_ATTR_CONCURRENCY_CAPA = 9,
/* Unsigned 32-bit value */
QCA_WLAN_VENDOR_ATTR_MAX_CONCURRENT_CHANNELS_2_4_BAND = 10,
/* Unsigned 32-bit value */
QCA_WLAN_VENDOR_ATTR_MAX_CONCURRENT_CHANNELS_5_0_BAND = 11,
/* Unsigned 32-bit value from enum qca_set_band. */
QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE = 12,
/* Dummy (NOP) attribute for 64 bit padding */
QCA_WLAN_VENDOR_ATTR_PAD = 13,
/* Unique FTM session cookie (Unsigned 64 bit). Specified in
* QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION. Reported in
* the session in QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT and
* QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE.
*/
QCA_WLAN_VENDOR_ATTR_FTM_SESSION_COOKIE = 14,
/* Indoor location capabilities, returned by
* QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA.
* see enum qca_wlan_vendor_attr_loc_capa.
*/
QCA_WLAN_VENDOR_ATTR_LOC_CAPA = 15,
/* Array of nested attributes containing information about each peer
* in FTM measurement session. See enum qca_wlan_vendor_attr_peer_info
* for supported attributes for each peer.
*/
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEERS = 16,
/* Array of nested attributes containing measurement results for
* one or more peers, reported by the
* QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT event.
* See enum qca_wlan_vendor_attr_peer_result for list of supported
* attributes.
*/
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEER_RESULTS = 17,
/* Flag attribute for enabling or disabling responder functionality. */
QCA_WLAN_VENDOR_ATTR_FTM_RESPONDER_ENABLE = 18,
/* Used in the QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER
* command to specify the LCI report that will be sent by
* the responder during a measurement exchange. The format is
* defined in IEEE P802.11-REVmc/D7.0, 9.4.2.22.10.
*/
QCA_WLAN_VENDOR_ATTR_FTM_LCI = 19,
/* Used in the QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER
* command to specify the location civic report that will
* be sent by the responder during a measurement exchange.
* The format is defined in IEEE P802.11-REVmc/D7.0, 9.4.2.22.13.
*/
QCA_WLAN_VENDOR_ATTR_FTM_LCR = 20,
/* Session/measurement completion status code,
* reported in QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE and
* QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT
* see enum qca_vendor_attr_loc_session_status.
*/
QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS = 21,
/* Initial dialog token used by responder (0 if not specified),
* unsigned 8 bit value.
*/
QCA_WLAN_VENDOR_ATTR_FTM_INITIAL_TOKEN = 22,
/* AOA measurement type. Requested in QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS
* and optionally in QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION if
* AOA measurements are needed as part of an FTM session.
* Reported by QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT. See
* enum qca_wlan_vendor_attr_aoa_type.
*/
QCA_WLAN_VENDOR_ATTR_AOA_TYPE = 23,
/* A bit mask (unsigned 32 bit value) of antenna arrays used
* by indoor location measurements. Refers to the antenna
* arrays described by QCA_VENDOR_ATTR_LOC_CAPA_ANTENNA_ARRAYS.
*/
QCA_WLAN_VENDOR_ATTR_LOC_ANTENNA_ARRAY_MASK = 24,
/* AOA measurement data. Its contents depends on the AOA measurement
* type and antenna array mask:
* QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE: array of U16 values,
* phase of the strongest CIR path for each antenna in the measured
* array(s).
* QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP: array of 2 U16
* values, phase and amplitude of the strongest CIR path for each
* antenna in the measured array(s).
*/
QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT = 25,
/* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command
* to specify the chain number (unsigned 32 bit value) to inquire
* the corresponding antenna RSSI value
*/
QCA_WLAN_VENDOR_ATTR_CHAIN_INDEX = 26,
/* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command
* to report the specific antenna RSSI value (unsigned 32 bit value)
*/
QCA_WLAN_VENDOR_ATTR_CHAIN_RSSI = 27,
/* Frequency in MHz, various uses. Unsigned 32 bit value */
QCA_WLAN_VENDOR_ATTR_FREQ = 28,
/* TSF timer value, unsigned 64 bit value.
* May be returned by various commands.
*/
QCA_WLAN_VENDOR_ATTR_TSF = 29,
/* DMG RF sector index, unsigned 16 bit number. Valid values are
* 0..127 for sector indices or 65535 as special value used to
* unlock sector selection in
* QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR.
*/
QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX = 30,
/* DMG RF sector type, unsigned 8 bit value. One of the values
* in enum qca_wlan_vendor_attr_dmg_rf_sector_type.
*/
QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE = 31,
/* Bitmask of DMG RF modules for which information is requested. Each
* bit corresponds to an RF module with the same index as the bit
* number. Unsigned 32 bit number but only low 8 bits can be set since
* all DMG chips currently have up to 8 RF modules.
*/
QCA_WLAN_VENDOR_ATTR_DMG_RF_MODULE_MASK = 32,
/* Array of nested attributes where each entry is DMG RF sector
* configuration for a single RF module.
* Attributes for each entry are taken from enum
* qca_wlan_vendor_attr_dmg_rf_sector_cfg.
* Specified in QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG
* and returned by QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG.
*/
QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG = 33,
/* Used in QCA_NL80211_VENDOR_SUBCMD_STATS_EXT command
* to report frame aggregation statistics to userspace.
*/
QCA_WLAN_VENDOR_ATTR_RX_AGGREGATION_STATS_HOLES_NUM = 34,
QCA_WLAN_VENDOR_ATTR_RX_AGGREGATION_STATS_HOLES_INFO = 35,
/* Unsigned 8-bit value representing MBO transition reason code as
* provided by the AP used by subcommand
* QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS. This is
* specified by the userspace in the request to the driver.
*/
QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON = 36,
/* Array of nested attributes, BSSID and status code, used by subcommand
* QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS, where each
* entry is taken from enum qca_wlan_vendor_attr_btm_candidate_info.
* The userspace space specifies the list/array of candidate BSSIDs in
* the order of preference in the request. The driver specifies the
* status code, for each BSSID in the list, in the response. The
* acceptable candidates are listed in the order preferred by the
* driver.
*/
QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO = 37,
/* Used in QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT command
* See enum qca_wlan_vendor_attr_brp_ant_limit_mode.
*/
QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE = 38,
/* Used in QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT command
* to define the number of antennas to use for BRP.
* different purpose in each ANT_LIMIT_MODE:
* DISABLE - ignored
* EFFECTIVE - upper limit to number of antennas to be used
* FORCE - exact number of antennas to be used
* unsigned 8 bit value
*/
QCA_WLAN_VENDOR_ATTR_BRP_ANT_NUM_LIMIT = 39,
/* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command
* to report the corresponding antenna index to the chain RSSI value
*/
QCA_WLAN_VENDOR_ATTR_ANTENNA_INFO = 40,
/* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command to report
* the specific antenna EVM value (unsigned 32 bit value). With a
* determinate group of antennas, the driver specifies the EVM value
* for each antenna ID, and application extract them in user space.
*/
QCA_WLAN_VENDOR_ATTR_CHAIN_EVM = 41,
/*
* Used in QCA_NL80211_VENDOR_SUBCMD_GET_FW_STATE command to report
* wlan firmware current state. FW state is an unsigned 8 bit value,
* one of the values in enum qca_wlan_vendor_attr_fw_state.
*/
QCA_WLAN_VENDOR_ATTR_FW_STATE = 42,
/* keep last */
QCA_WLAN_VENDOR_ATTR_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_MAX = QCA_WLAN_VENDOR_ATTR_AFTER_LAST - 1,
};
enum qca_roaming_policy {
QCA_ROAMING_NOT_ALLOWED,
QCA_ROAMING_ALLOWED_WITHIN_ESS,
};
/**
* enum qca_roam_reason - Represents the reason codes for roaming. Used by
* QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_REASON.
*
* @QCA_ROAM_REASON_UNKNOWN: Any reason that do not classify under the below
* reasons.
*
* @QCA_ROAM_REASON_PER: Roam triggered when packet error rates (PER) breached
* the configured threshold.
*
* @QCA_ROAM_REASON_BEACON_MISS: Roam triggered due to the continuous configured
* beacon misses from the then connected AP.
*
* @QCA_ROAM_REASON_POOR_RSSI: Roam triggered due to the poor RSSI reported
* by the connected AP.
*
* @QCA_ROAM_REASON_BETTER_RSSI: Roam triggered for finding a BSS with a better
* RSSI than the connected BSS. Here the RSSI of the current BSS is not poor.
*
* @QCA_ROAM_REASON_CONGESTION: Roam triggered considering the connected channel
* or environment being very noisy or congested.
*
* @QCA_ROAM_REASON_EXPLICIT_REQUEST: Roam triggered due to an explicit request
* from the user (user space).
*
* @QCA_ROAM_REASON_BTM: Roam triggered due to BTM Request frame received from
* the connected AP.
*
* @QCA_ROAM_REASON_BSS_LOAD: Roam triggered due to the channel utilization
* breaching out the configured threshold.
*/
enum qca_roam_reason {
QCA_ROAM_REASON_UNKNOWN,
QCA_ROAM_REASON_PER,
QCA_ROAM_REASON_BEACON_MISS,
QCA_ROAM_REASON_POOR_RSSI,
QCA_ROAM_REASON_BETTER_RSSI,
QCA_ROAM_REASON_CONGESTION,
QCA_ROAM_REASON_USER_TRIGGER,
QCA_ROAM_REASON_BTM,
QCA_ROAM_REASON_BSS_LOAD,
};
enum qca_wlan_vendor_attr_roam_auth {
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_BSSID,
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_REQ_IE,
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RESP_IE,
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AUTHORIZED,
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_KEY_REPLAY_CTR,
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KCK,
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KEK,
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_SUBNET_STATUS,
/* Indicates the status of re-association requested by user space for
* the BSSID specified by QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_BSSID.
* Type u16.
* Represents the status code from AP. Use
* %WLAN_STATUS_UNSPECIFIED_FAILURE if the device cannot give you the
* real status code for failures.
*/
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS,
/* This attribute indicates that the old association was maintained when
* a re-association is requested by user space and that re-association
* attempt fails (i.e., cannot connect to the requested BSS, but can
* remain associated with the BSS with which the association was in
* place when being requested to roam). Used along with
* WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS to indicate the current
* re-association status. Type flag.
* This attribute is applicable only for re-association failure cases.
*/
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RETAIN_CONNECTION,
/* This attribute specifies the PMK if one was newly generated during
* FILS roaming. This is added to the PMKSA cache and is used in
* subsequent connections with PMKSA caching.
*/
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMK = 11,
/* This attribute specifies the PMKID used/generated for the current
* FILS roam. This is used in subsequent connections with PMKSA caching.
*/
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMKID = 12,
/* A 16-bit unsigned value specifying the next sequence number to use
* in ERP message in the currently associated realm. This is used in
* doing subsequent ERP based connections in the same realm.
*/
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_FILS_ERP_NEXT_SEQ_NUM = 13,
/* A 16-bit unsigned value representing the reasons for the roaming.
* Defined by enum qca_roam_reason.
*/
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_REASON = 14,
/* keep last */
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_MAX =
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AFTER_LAST - 1
};
enum qca_wlan_vendor_attr_p2p_listen_offload {
QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INVALID = 0,
/* A 32-bit unsigned value; the P2P listen frequency (MHz); must be one
* of the social channels.
*/
QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CHANNEL,
/* A 32-bit unsigned value; the P2P listen offload period (ms).
*/
QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_PERIOD,
/* A 32-bit unsigned value; the P2P listen interval duration (ms).
*/
QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INTERVAL,
/* A 32-bit unsigned value; number of interval times the firmware needs
* to run the offloaded P2P listen operation before it stops.
*/
QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_COUNT,
/* An array of arbitrary binary data with one or more 8-byte values.
* The device types include both primary and secondary device types.
*/
QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_DEVICE_TYPES,
/* An array of unsigned 8-bit characters; vendor information elements.
*/
QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_VENDOR_IE,
/* A 32-bit unsigned value; a control flag to indicate whether listen
* results need to be flushed to wpa_supplicant.
*/
QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CTRL_FLAG,
/* A 8-bit unsigned value; reason code for P2P listen offload stop
* event.
*/
QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_STOP_REASON,
/* keep last */
QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_MAX =
QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST - 1
};
enum qca_wlan_vendor_attr_acs_offload {
QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL,
QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL,
QCA_WLAN_VENDOR_ATTR_ACS_HW_MODE,
QCA_WLAN_VENDOR_ATTR_ACS_HT_ENABLED,
QCA_WLAN_VENDOR_ATTR_ACS_HT40_ENABLED,
QCA_WLAN_VENDOR_ATTR_ACS_VHT_ENABLED,
QCA_WLAN_VENDOR_ATTR_ACS_CHWIDTH,
QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST,
QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL,
QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL,
QCA_WLAN_VENDOR_ATTR_ACS_FREQ_LIST,
/* keep last */
QCA_WLAN_VENDOR_ATTR_ACS_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_ACS_MAX =
QCA_WLAN_VENDOR_ATTR_ACS_AFTER_LAST - 1
};
enum qca_wlan_vendor_acs_hw_mode {
QCA_ACS_MODE_IEEE80211B,
QCA_ACS_MODE_IEEE80211G,
QCA_ACS_MODE_IEEE80211A,
QCA_ACS_MODE_IEEE80211AD,
QCA_ACS_MODE_IEEE80211ANY,
};
/**
* enum qca_wlan_vendor_features - Vendor device/driver feature flags
*
* @QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD: Device supports key
* management offload, a mechanism where the station's firmware
* does the exchange with the AP to establish the temporal keys
* after roaming, rather than having the user space wpa_supplicant do it.
* @QCA_WLAN_VENDOR_FEATURE_SUPPORT_HW_MODE_ANY: Device supports automatic
* band selection based on channel selection results.
* @QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS: Device supports
* simultaneous off-channel operations.
* @QCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD: Device supports P2P
* Listen offload; a mechanism where the station's firmware takes care of
* responding to incoming Probe Request frames received from other P2P
* Devices whilst in Listen state, rather than having the user space
* wpa_supplicant do it. Information from received P2P requests are
* forwarded from firmware to host whenever the host processor wakes up.
* @QCA_WLAN_VENDOR_FEATURE_OCE_STA: Device supports all OCE non-AP STA
* specific features.
* @QCA_WLAN_VENDOR_FEATURE_OCE_AP: Device supports all OCE AP specific
* features.
* @QCA_WLAN_VENDOR_FEATURE_OCE_STA_CFON: Device supports OCE STA-CFON
* specific features only. If a Device sets this bit but not the
* %QCA_WLAN_VENDOR_FEATURE_OCE_AP, the userspace shall assume that
* this Device may not support all OCE AP functionalities but can support
* only OCE STA-CFON functionalities.
* @QCA_WLAN_VENDOR_FEATURE_SELF_MANAGED_REGULATORY: Device supports self
* managed regulatory.
* @QCA_WLAN_VENDOR_FEATURE_TWT: Device supports TWT (Target Wake Time).
* @NUM_QCA_WLAN_VENDOR_FEATURES: Number of assigned feature bits
*/
enum qca_wlan_vendor_features {
QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD = 0,
QCA_WLAN_VENDOR_FEATURE_SUPPORT_HW_MODE_ANY = 1,
QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS = 2,
QCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD = 3,
QCA_WLAN_VENDOR_FEATURE_OCE_STA = 4,
QCA_WLAN_VENDOR_FEATURE_OCE_AP = 5,
QCA_WLAN_VENDOR_FEATURE_OCE_STA_CFON = 6,
QCA_WLAN_VENDOR_FEATURE_SELF_MANAGED_REGULATORY = 7,
QCA_WLAN_VENDOR_FEATURE_TWT = 8,
NUM_QCA_WLAN_VENDOR_FEATURES /* keep last */
};
/**
* enum qca_wlan_vendor_attr_data_offload_ind - Vendor Data Offload Indication
*
* @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_SESSION: Session corresponding to
* the offloaded data.
* @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_PROTOCOL: Protocol of the offloaded
* data.
* @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_EVENT: Event type for the data offload
* indication.
*/
enum qca_wlan_vendor_attr_data_offload_ind {
QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_SESSION,
QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_PROTOCOL,
QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_EVENT,
/* keep last */
QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_MAX =
QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_AFTER_LAST - 1
};
/**
* enum qca_wlan_vendor_attr_ocb_set_config - Vendor subcmd attributes to set
* OCB config
*
* @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_COUNT: Number of channels in the
* configuration
* @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_SIZE: Size of the schedule
* @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_ARRAY: Array of channels
* @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_ARRAY: Array of channels to be
* scheduled
* @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_CHANNEL_ARRAY: Array of NDL channel
* information
* @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_ACTIVE_STATE_ARRAY: Array of NDL
* active state configuration
* @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_FLAGS: Configuration flags such as
* OCB_CONFIG_FLAG_80211_FRAME_MODE
* @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_DEF_TX_PARAM: Default TX parameters to
* use in the case that a packet is sent without a TX control header
* @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_TA_MAX_DURATION: Max duration after the
* last TA received that the local time set by TA is synchronous to other
* communicating OCB STAs.
*/
enum qca_wlan_vendor_attr_ocb_set_config {
QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_COUNT = 1,
QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_SIZE = 2,
QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_ARRAY = 3,
QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_ARRAY = 4,
QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_CHANNEL_ARRAY = 5,
QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_ACTIVE_STATE_ARRAY = 6,
QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_FLAGS = 7,
QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_DEF_TX_PARAM = 8,
QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_TA_MAX_DURATION = 9,
QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_MAX =
QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_AFTER_LAST - 1
};
/**
* enum qca_wlan_vendor_attr_ocb_set_utc_time - Vendor subcmd attributes to set
* UTC time
*
* @QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_VALUE: The UTC time as an array of
* 10 bytes
* @QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_ERROR: The time error as an array of
* 5 bytes
*/
enum qca_wlan_vendor_attr_ocb_set_utc_time {
QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_VALUE = 1,
QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_ERROR = 2,
QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_MAX =
QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_AFTER_LAST - 1
};
/**
* enum qca_wlan_vendor_attr_ocb_start_timing_advert - Vendor subcmd attributes
* to start sending timing advert frames
*
* @QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_CHANNEL_FREQ: Cannel frequency
* on which to send the frames
* @QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_REPEAT_RATE: Number of times
* the frame is sent in 5 seconds
*/
enum qca_wlan_vendor_attr_ocb_start_timing_advert {
QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_CHANNEL_FREQ = 1,
QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_REPEAT_RATE = 2,
QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_MAX =
QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_AFTER_LAST - 1
};
/**
* enum qca_wlan_vendor_attr_ocb_stop_timing_advert - Vendor subcmd attributes
* to stop timing advert
*
* @QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_CHANNEL_FREQ: The channel
* frequency on which to stop the timing advert
*/
enum qca_wlan_vendor_attr_ocb_stop_timing_advert {
QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_CHANNEL_FREQ = 1,
QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_MAX =
QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_AFTER_LAST - 1
};
/**
* enum qca_wlan_vendor_attr_ocb_get_tsf_response - Vendor subcmd attributes to
* get TSF timer value
*
* @QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_HIGH: Higher 32 bits of the
* timer
* @QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_LOW: Lower 32 bits of the timer
*/
enum qca_wlan_vendor_attr_ocb_get_tsf_resp {
QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_HIGH = 1,
QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_LOW = 2,
QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_MAX =
QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_AFTER_LAST - 1
};
enum qca_vendor_attr_get_preferred_freq_list {
QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_INVALID,
/* A 32-unsigned value; the interface type/mode for which the preferred
* frequency list is requested (see enum qca_iface_type for possible
* values); used in GET_PREFERRED_FREQ_LIST command from user-space to
* kernel and in the kernel response back to user-space.
*/
QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_IFACE_TYPE,
/* An array of 32-unsigned values; values are frequency (MHz); sent
* from kernel space to user space.
*/
QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST,
/* An array of nested values as per enum qca_wlan_vendor_attr_pcl
* attribute. Each element contains frequency (MHz), weight, and flag
* bit mask indicating how the frequency should be used in P2P
* negotiation; sent from kernel space to user space.
*/
QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_WEIGHED_PCL,
/* keep last */
QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_MAX =
QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST - 1
};
enum qca_vendor_attr_probable_oper_channel {
QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_INVALID,
/* 32-bit unsigned value; indicates the connection/iface type likely to
* come on this channel (see enum qca_iface_type).
*/
QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_IFACE_TYPE,
/* 32-bit unsigned value; the frequency (MHz) of the probable channel */
QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_FREQ,
/* keep last */
QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_MAX =
QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST - 1
};
enum qca_iface_type {
QCA_IFACE_TYPE_STA,
QCA_IFACE_TYPE_AP,
QCA_IFACE_TYPE_P2P_CLIENT,
QCA_IFACE_TYPE_P2P_GO,
QCA_IFACE_TYPE_IBSS,
QCA_IFACE_TYPE_TDLS,
};
enum qca_set_band {
QCA_SETBAND_AUTO,
QCA_SETBAND_5G,
QCA_SETBAND_2G,
};
/**
* enum qca_access_policy - Access control policy
*
* Access control policy is applied on the configured IE
* (QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE).
* To be set with QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY.
*
* @QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED: Deny Wi-Fi connections which match
* the specific configuration (IE) set, i.e., allow all the
* connections which do not match the configuration.
* @QCA_ACCESS_POLICY_DENY_UNLESS_LISTED: Accept Wi-Fi connections which match
* the specific configuration (IE) set, i.e., deny all the
* connections which do not match the configuration.
*/
enum qca_access_policy {
QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED,
QCA_ACCESS_POLICY_DENY_UNLESS_LISTED,
};
/**
* enum qca_vendor_attr_get_tsf: Vendor attributes for TSF capture
* @QCA_WLAN_VENDOR_ATTR_TSF_CMD: enum qca_tsf_operation (u32)
* @QCA_WLAN_VENDOR_ATTR_TSF_TIMER_VALUE: Unsigned 64 bit TSF timer value
* @QCA_WLAN_VENDOR_ATTR_TSF_SOC_TIMER_VALUE: Unsigned 64 bit Synchronized
* SOC timer value at TSF capture
*/
enum qca_vendor_attr_tsf_cmd {
QCA_WLAN_VENDOR_ATTR_TSF_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_TSF_CMD,
QCA_WLAN_VENDOR_ATTR_TSF_TIMER_VALUE,
QCA_WLAN_VENDOR_ATTR_TSF_SOC_TIMER_VALUE,
QCA_WLAN_VENDOR_ATTR_TSF_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_TSF_MAX =
QCA_WLAN_VENDOR_ATTR_TSF_AFTER_LAST - 1
};
/**
* enum qca_tsf_operation: TSF driver commands
* @QCA_TSF_CAPTURE: Initiate TSF Capture
* @QCA_TSF_GET: Get TSF capture value
* @QCA_TSF_SYNC_GET: Initiate TSF capture and return with captured value
*/
enum qca_tsf_cmd {
QCA_TSF_CAPTURE,
QCA_TSF_GET,
QCA_TSF_SYNC_GET,
};
/**
* enum qca_vendor_attr_wisa_cmd
* @QCA_WLAN_VENDOR_ATTR_WISA_MODE: WISA mode value (u32)
* WISA setup vendor commands
*/
enum qca_vendor_attr_wisa_cmd {
QCA_WLAN_VENDOR_ATTR_WISA_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_WISA_MODE,
QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_WISA_MAX =
QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST - 1
};
/* IEEE 802.11 Vendor Specific elements */
/**
* enum qca_vendor_element_id - QCA Vendor Specific element types
*
* These values are used to identify QCA Vendor Specific elements. The
* payload of the element starts with the three octet OUI (OUI_QCA) and
* is followed by a single octet type which is defined by this enum.
*
* @QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST: P2P preferred channel list.
* This element can be used to specify preference order for supported
* channels. The channels in this list are in preference order (the first
* one has the highest preference) and are described as a pair of
* (global) Operating Class and Channel Number (each one octet) fields.
*
* This extends the standard P2P functionality by providing option to have
* more than one preferred operating channel. When this element is present,
* it replaces the preference indicated in the Operating Channel attribute.
* For supporting other implementations, the Operating Channel attribute is
* expected to be used with the highest preference channel. Similarly, all
* the channels included in this Preferred channel list element are
* expected to be included in the Channel List attribute.
*
* This vendor element may be included in GO Negotiation Request, P2P
* Invitation Request, and Provision Discovery Request frames.
*
* @QCA_VENDOR_ELEM_HE_CAPAB: HE Capabilities element.
* This element can be used for pre-standard publication testing of HE
* before P802.11ax draft assigns the element ID. The payload of this
* vendor specific element is defined by the latest P802.11ax draft.
* Please note that the draft is still work in progress and this element
* payload is subject to change.
*
* @QCA_VENDOR_ELEM_HE_OPER: HE Operation element.
* This element can be used for pre-standard publication testing of HE
* before P802.11ax draft assigns the element ID. The payload of this
* vendor specific element is defined by the latest P802.11ax draft.
* Please note that the draft is still work in progress and this element
* payload is subject to change.
*
* @QCA_VENDOR_ELEM_RAPS: RAPS element (OFDMA-based Random Access Parameter Set
* element).
* This element can be used for pre-standard publication testing of HE
* before P802.11ax draft assigns the element ID extension. The payload of
* this vendor specific element is defined by the latest P802.11ax draft
* (not including the Element ID Extension field). Please note that the
* draft is still work in progress and this element payload is subject to
* change.
*
* @QCA_VENDOR_ELEM_MU_EDCA_PARAMS: MU EDCA Parameter Set element.
* This element can be used for pre-standard publication testing of HE
* before P802.11ax draft assigns the element ID extension. The payload of
* this vendor specific element is defined by the latest P802.11ax draft
* (not including the Element ID Extension field). Please note that the
* draft is still work in progress and this element payload is subject to
* change.
*
* @QCA_VENDOR_ELEM_BSS_COLOR_CHANGE: BSS Color Change Announcement element.
* This element can be used for pre-standard publication testing of HE
* before P802.11ax draft assigns the element ID extension. The payload of
* this vendor specific element is defined by the latest P802.11ax draft
* (not including the Element ID Extension field). Please note that the
* draft is still work in progress and this element payload is subject to
* change.
*/
enum qca_vendor_element_id {
QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST = 0,
QCA_VENDOR_ELEM_HE_CAPAB = 1,
QCA_VENDOR_ELEM_HE_OPER = 2,
QCA_VENDOR_ELEM_RAPS = 3,
QCA_VENDOR_ELEM_MU_EDCA_PARAMS = 4,
QCA_VENDOR_ELEM_BSS_COLOR_CHANGE = 5,
};
/**
* enum qca_wlan_vendor_attr_scan - Specifies vendor scan attributes
*
* @QCA_WLAN_VENDOR_ATTR_SCAN_IE: IEs that should be included as part of scan
* @QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES: Nested unsigned 32-bit attributes
* with frequencies to be scanned (in MHz)
* @QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS: Nested attribute with SSIDs to be scanned
* @QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES: Nested array attribute of supported
* rates to be included
* @QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE: flag used to send probe requests
* at non CCK rate in 2GHz band
* @QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS: Unsigned 32-bit scan flags
* @QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE: Unsigned 64-bit cookie provided by the
* driver for the specific scan request
* @QCA_WLAN_VENDOR_ATTR_SCAN_STATUS: Unsigned 8-bit status of the scan
* request decoded as in enum scan_status
* @QCA_WLAN_VENDOR_ATTR_SCAN_MAC: 6-byte MAC address to use when randomisation
* scan flag is set
* @QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK: 6-byte MAC address mask to be used with
* randomisation
* @QCA_WLAN_VENDOR_ATTR_SCAN_BSSID: 6-byte MAC address representing the
* specific BSSID to scan for.
*/
enum qca_wlan_vendor_attr_scan {
QCA_WLAN_VENDOR_ATTR_SCAN_INVALID_PARAM = 0,
QCA_WLAN_VENDOR_ATTR_SCAN_IE = 1,
QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES = 2,
QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS = 3,
QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES = 4,
QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE = 5,
QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS = 6,
QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE = 7,
QCA_WLAN_VENDOR_ATTR_SCAN_STATUS = 8,
QCA_WLAN_VENDOR_ATTR_SCAN_MAC = 9,
QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK = 10,
QCA_WLAN_VENDOR_ATTR_SCAN_BSSID = 11,
QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_SCAN_MAX =
QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST - 1
};
/**
* enum scan_status - Specifies the valid values the vendor scan attribute
* QCA_WLAN_VENDOR_ATTR_SCAN_STATUS can take
*
* @VENDOR_SCAN_STATUS_NEW_RESULTS: implies the vendor scan is successful with
* new scan results
* @VENDOR_SCAN_STATUS_ABORTED: implies the vendor scan was aborted in-between
*/
enum scan_status {
VENDOR_SCAN_STATUS_NEW_RESULTS,
VENDOR_SCAN_STATUS_ABORTED,
VENDOR_SCAN_STATUS_MAX,
};
/**
* enum qca_vendor_attr_ota_test - Specifies the values for vendor
* command QCA_NL80211_VENDOR_SUBCMD_OTA_TEST
* @QCA_WLAN_VENDOR_ATTR_OTA_TEST_ENABLE: enable ota test
*/
enum qca_vendor_attr_ota_test {
QCA_WLAN_VENDOR_ATTR_OTA_TEST_INVALID,
/* 8-bit unsigned value to indicate if OTA test is enabled */
QCA_WLAN_VENDOR_ATTR_OTA_TEST_ENABLE,
/* keep last */
QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_OTA_TEST_MAX =
QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST - 1
};
/**
* enum qca_vendor_attr_txpower_scale - vendor sub commands index
*
* @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE: scaling value
*/
enum qca_vendor_attr_txpower_scale {
QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_INVALID,
/* 8-bit unsigned value to indicate the scaling of tx power */
QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE,
/* keep last */
QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_MAX =
QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST - 1
};
/**
* enum qca_vendor_attr_txpower_decr_db - Attributes for TX power decrease
*
* These attributes are used with QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_DECR_DB.
*/
enum qca_vendor_attr_txpower_decr_db {
QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_INVALID,
/* 8-bit unsigned value to indicate the reduction of TX power in dB for
* a virtual interface.
*/
QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB,
/* keep last */
QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_MAX =
QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_AFTER_LAST - 1
};
/* Attributes for data used by
* QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and
* QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION subcommands.
*/
enum qca_wlan_vendor_attr_config {
QCA_WLAN_VENDOR_ATTR_CONFIG_INVALID = 0,
/* Unsigned 32-bit value to set the DTIM period.
* Whether the wifi chipset wakes at every dtim beacon or a multiple of
* the DTIM period. If DTIM is set to 3, the STA shall wake up every 3
* DTIM beacons.
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_DYNAMIC_DTIM = 1,
/* Unsigned 32-bit value to set the wifi_iface stats averaging factor
* used to calculate statistics like average the TSF offset or average
* number of frame leaked.
* For instance, upon Beacon frame reception:
* current_avg = ((beacon_TSF - TBTT) * factor + previous_avg * (0x10000 - factor) ) / 0x10000
* For instance, when evaluating leaky APs:
* current_avg = ((num frame received within guard time) * factor + previous_avg * (0x10000 - factor)) / 0x10000
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_STATS_AVG_FACTOR = 2,
/* Unsigned 32-bit value to configure guard time, i.e., when
* implementing IEEE power management based on frame control PM bit, how
* long the driver waits before shutting down the radio and after
* receiving an ACK frame for a Data frame with PM bit set.
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_GUARD_TIME = 3,
/* Unsigned 32-bit value to change the FTM capability dynamically */
QCA_WLAN_VENDOR_ATTR_CONFIG_FINE_TIME_MEASUREMENT = 4,
/* Unsigned 16-bit value to configure maximum TX rate dynamically */
QCA_WLAN_VENDOR_ATTR_CONF_TX_RATE = 5,
/* Unsigned 32-bit value to configure the number of continuous
* Beacon Miss which shall be used by the firmware to penalize
* the RSSI.
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS = 6,
/* Unsigned 8-bit value to configure the channel avoidance indication
* behavior. Firmware to send only one indication and ignore duplicate
* indications when set to avoid multiple Apps wakeups.
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_AVOIDANCE_IND = 7,
/* 8-bit unsigned value to configure the maximum TX MPDU for
* aggregation.
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_TX_MPDU_AGGREGATION = 8,
/* 8-bit unsigned value to configure the maximum RX MPDU for
* aggregation.
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_RX_MPDU_AGGREGATION = 9,
/* 8-bit unsigned value to configure the Non aggregrate/11g sw
* retry threshold (0 disable, 31 max).
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_NON_AGG_RETRY = 10,
/* 8-bit unsigned value to configure the aggregrate sw
* retry threshold (0 disable, 31 max).
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_AGG_RETRY = 11,
/* 8-bit unsigned value to configure the MGMT frame
* retry threshold (0 disable, 31 max).
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_MGMT_RETRY = 12,
/* 8-bit unsigned value to configure the CTRL frame
* retry threshold (0 disable, 31 max).
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_CTRL_RETRY = 13,
/* 8-bit unsigned value to configure the propagation delay for
* 2G/5G band (0~63, units in us)
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_DELAY = 14,
/* Unsigned 32-bit value to configure the number of unicast TX fail
* packet count. The peer is disconnected once this threshold is
* reached.
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_TX_FAIL_COUNT = 15,
/* Attribute used to set scan default IEs to the driver.
*
* These IEs can be used by scan operations that will be initiated by
* the driver/firmware.
*
* For further scan requests coming to the driver, these IEs should be
* merged with the IEs received along with scan request coming to the
* driver. If a particular IE is present in the scan default IEs but not
* present in the scan request, then that IE should be added to the IEs
* sent in the Probe Request frames for that scan request.
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_DEFAULT_IES = 16,
/* Unsigned 32-bit attribute for generic commands */
QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_COMMAND = 17,
/* Unsigned 32-bit value attribute for generic commands */
QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_VALUE = 18,
/* Unsigned 32-bit data attribute for generic command response */
QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA = 19,
/* Unsigned 32-bit length attribute for
* QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_LENGTH = 20,
/* Unsigned 32-bit flags attribute for
* QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_FLAGS = 21,
/* Unsigned 32-bit, defining the access policy.
* See enum qca_access_policy. Used with
* QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST.
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY = 22,
/* Sets the list of full set of IEs for which a specific access policy
* has to be applied. Used along with
* QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY to control the access.
* Zero length payload can be used to clear this access constraint.
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST = 23,
/* Unsigned 32-bit, specifies the interface index (netdev) for which the
* corresponding configurations are applied. If the interface index is
* not specified, the configurations are attributed to the respective
* wiphy.
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_IFINDEX = 24,
/* 8-bit unsigned value to trigger QPower: 1-Enable, 0-Disable */
QCA_WLAN_VENDOR_ATTR_CONFIG_QPOWER = 25,
/* 8-bit unsigned value to configure the driver and below layers to
* ignore the assoc disallowed set by APs while connecting
* 1-Ignore, 0-Don't ignore
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_IGNORE_ASSOC_DISALLOWED = 26,
/* 32-bit unsigned value to trigger antenna diversity features:
* 1-Enable, 0-Disable
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_ENA = 27,
/* 32-bit unsigned value to configure specific chain antenna */
QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_CHAIN = 28,
/* 32-bit unsigned value to trigger cycle selftest
* 1-Enable, 0-Disable
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST = 29,
/* 32-bit unsigned to configure the cycle time of selftest
* the unit is micro-second
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST_INTVL = 30,
/* 32-bit unsigned value to set reorder timeout for AC_VO */
QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_VOICE = 31,
/* 32-bit unsigned value to set reorder timeout for AC_VI */
QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_VIDEO = 32,
/* 32-bit unsigned value to set reorder timeout for AC_BE */
QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_BESTEFFORT = 33,
/* 32-bit unsigned value to set reorder timeout for AC_BK */
QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_BACKGROUND = 34,
/* 6-byte MAC address to point out the specific peer */
QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_PEER_MAC = 35,
/* 32-bit unsigned value to set window size for specific peer */
QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_WINLIMIT = 36,
/* 8-bit unsigned value to set the beacon miss threshold in 2.4 GHz */
QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_MISS_THRESHOLD_24 = 37,
/* 8-bit unsigned value to set the beacon miss threshold in 5 GHz */
QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_MISS_THRESHOLD_5 = 38,
/* 32-bit unsigned value to configure 5 or 10 MHz channel width for
* station device while in disconnect state. The attribute use the
* value of enum nl80211_chan_width: NL80211_CHAN_WIDTH_5 means 5 MHz,
* NL80211_CHAN_WIDTH_10 means 10 MHz. If set, the device work in 5 or
* 10 MHz channel width, the station will not connect to a BSS using 20
* MHz or higher bandwidth. Set to NL80211_CHAN_WIDTH_20_NOHT to
* clear this constraint.
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_SUB20_CHAN_WIDTH = 39,
/* 32-bit unsigned value to configure the propagation absolute delay
* for 2G/5G band (units in us)
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_ABS_DELAY = 40,
/* 32-bit unsigned value to set probe period */
QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_PROBE_PERIOD = 41,
/* 32-bit unsigned value to set stay period */
QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_STAY_PERIOD = 42,
/* 32-bit unsigned value to set snr diff */
QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SNR_DIFF = 43,
/* 32-bit unsigned value to set probe dwell time */
QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_PROBE_DWELL_TIME = 44,
/* 32-bit unsigned value to set mgmt snr weight */
QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_MGMT_SNR_WEIGHT = 45,
/* 32-bit unsigned value to set data snr weight */
QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_DATA_SNR_WEIGHT = 46,
/* 32-bit unsigned value to set ack snr weight */
QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_ACK_SNR_WEIGHT = 47,
/* 32-bit unsigned value to configure the listen interval.
* This is in units of beacon intervals. This configuration alters
* the negotiated listen interval with the AP during the connection.
* It is highly recommended to configure a value less than or equal to
* the one negotiated during the association. Configuring any greater
* value can have adverse effects (frame loss, AP disassociating STA,
* etc.).
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_LISTEN_INTERVAL = 48,
/*
* 8 bit unsigned value that is set on an AP/GO virtual interface to
* disable operations that would cause the AP/GO to leave its operating
* channel.
*
* This will restrict the scans to the AP/GO operating channel and the
* channels of the other band, if DBS is supported.A STA/CLI interface
* brought up after this setting is enabled, will be restricted to
* connecting to devices only on the AP/GO interface's operating channel
* or on the other band in DBS case. P2P supported channel list is
* modified, to only include AP interface's operating-channel and the
* channels of the other band if DBS is supported.
*
* These restrictions are only applicable as long as the AP/GO interface
* is alive. If the AP/GO interface is brought down then this
* setting/restriction is forgotten.
*
* If this variable is set on an AP/GO interface while a multi-channel
* concurrent session is active, it has no effect on the operation of
* the current interfaces, other than restricting the scan to the AP/GO
* operating channel and the other band channels if DBS is supported.
* However, if the STA is brought down and restarted then the new STA
* connection will either be formed on the AP/GO channel or on the
* other band in a DBS case. This is because of the scan being
* restricted on these channels as mentioned above.
*
* 1-Restrict / 0-Don't restrict offchannel operations.
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_RESTRICT_OFFCHANNEL = 49,
/*
* 8 bit unsigned value to enable/disable LRO (Large Receive Offload)
* on an interface.
* 1 - Enable, 0 - Disable.
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_LRO = 50,
/*
* 8 bit unsigned value to globally enable/disable scan
* 1 - Enable, 0 - Disable.
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_ENABLE = 51,
/* 8-bit unsigned value to set the total beacon miss count
* This parameter will set the total beacon miss count.
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_TOTAL_BEACON_MISS_COUNT = 52,
/* Unsigned 32-bit value to configure the number of continuous
* Beacon Miss which shall be used by the firmware to penalize
* the RSSI for BTC.
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS_BTC = 53,
/* 8-bit unsigned value to configure the driver and below layers to
* enable/disable all FILS features.
* 0-enable, 1-disable
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_DISABLE_FILS = 54,
/* 16-bit unsigned value to configure the level of WLAN latency
* module. See enum qca_wlan_vendor_attr_config_latency_level.
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL = 55,
/* 8-bit unsigned value indicating the driver to use the RSNE as-is from
* the connect interface. Exclusively used for the scenarios where the
* device is used as a test bed device with special functionality and
* not recommended for production. This helps driver to not validate the
* RSNE passed from user space and thus allow arbitrary IE data to be
* used for testing purposes.
* 1-enable, 0-disable.
* Applications set/reset this configuration. If not reset, this
* parameter remains in use until the driver is unloaded.
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_RSN_IE = 56,
/* 8-bit unsigned value to trigger green Tx power saving.
* 1-Enable, 0-Disable
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_GTX = 57,
/* keep last */
QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_CONFIG_MAX =
QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_sap_config - Parameters for AP configuration
*/
enum qca_wlan_vendor_attr_sap_config {
QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_INVALID = 0,
/* 1 - reserved for QCA */
/* List of frequencies on which AP is expected to operate.
* This is irrespective of ACS configuration. This list is a priority
* based one and is looked for before the AP is created to ensure the
* best concurrency sessions (avoid MCC and use DBS/SCC) co-exist in
* the system.
*/
QCA_WLAN_VENDOR_ATTR_SAP_MANDATORY_FREQUENCY_LIST = 2,
QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_MAX =
QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_sap_conditional_chan_switch - Parameters for AP
* conditional channel switch
*/
enum qca_wlan_vendor_attr_sap_conditional_chan_switch {
QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_INVALID = 0,
/* Priority based frequency list (an array of u32 values in host byte
* order)
*/
QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST = 1,
/* Status of the conditional switch (u32).
* 0: Success, Non-zero: Failure
*/
QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS = 2,
QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_MAX =
QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST - 1,
};
/**
* enum qca_wlan_gpio_attr - Parameters for GPIO configuration
*/
enum qca_wlan_gpio_attr {
QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INVALID = 0,
/* Unsigned 32-bit attribute for GPIO command */
QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND,
/* Unsigned 32-bit attribute for GPIO PIN number to configure */
QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PINNUM,
/* Unsigned 32-bit attribute for GPIO value to configure */
QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_VALUE,
/* Unsigned 32-bit attribute for GPIO pull type */
QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PULL_TYPE,
/* Unsigned 32-bit attribute for GPIO interrupt mode */
QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTR_MODE,
/* keep last */
QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST,
QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_MAX =
QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST - 1
};
/**
* qca_wlan_set_qdepth_thresh_attr - Parameters for setting
* MSDUQ depth threshold per peer per tid in the target
*
* Associated Vendor Command:
* QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH
*/
enum qca_wlan_set_qdepth_thresh_attr {
QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_INVALID = 0,
/* 6-byte MAC address */
QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_MAC_ADDR,
/* Unsigned 32-bit attribute for holding the TID */
QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_TID,
/* Unsigned 32-bit attribute for holding the update mask
* bit 0 - Update high priority msdu qdepth threshold
* bit 1 - Update low priority msdu qdepth threshold
* bit 2 - Update UDP msdu qdepth threshold
* bit 3 - Update Non UDP msdu qdepth threshold
* rest of bits are reserved
*/
QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_UPDATE_MASK,
/* Unsigned 32-bit attribute for holding the threshold value */
QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_VALUE,
/* keep last */
QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_LAST,
QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_MAX =
QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_get_hw_capability - Wi-Fi hardware capability
*/
enum qca_wlan_vendor_attr_get_hw_capability {
QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_INVALID,
/* Antenna isolation
* An attribute used in the response.
* The content of this attribute is encoded in a byte array. Each byte
* value is an antenna isolation value. The array length is the number
* of antennas.
*/
QCA_WLAN_VENDOR_ATTR_ANTENNA_ISOLATION,
/* Request HW capability
* An attribute used in the request.
* The content of this attribute is a u32 array for one or more of
* hardware capabilities (attribute IDs) that are being requested. Each
* u32 value has a value from this
* enum qca_wlan_vendor_attr_get_hw_capability
* identifying which capabilities are requested.
*/
QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY,
/* keep last */
QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_MAX =
QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_ll_stats_ext - Attributes for MAC layer monitoring
* offload which is an extension for LL_STATS.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD: Monitoring period. Unit in ms.
* If MAC counters do not exceed the threshold, FW will report monitored
* link layer counters periodically as this setting. The first report is
* always triggered by this timer.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD: It is a percentage (1-99).
* For each MAC layer counter, FW holds two copies. One is the current value.
* The other is the last report. Once a current counter's increment is larger
* than the threshold, FW will indicate that counter to host even if the
* monitoring timer does not expire.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG: Peer STA power state change
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID: TID of MSDU
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU: Count of MSDU with the same
* failure code.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS: TX failure code
* 1: TX packet discarded
* 2: No ACK
* 3: Postpone
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_MAC_ADDRESS: peer MAC address
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_STATE: Peer STA current state
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_GLOBAL: Global threshold.
* Threshold for all monitored parameters. If per counter dedicated threshold
* is not enabled, this threshold will take effect.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_EVENT_MODE: Indicate what triggers this
* event, PERORID_TIMEOUT == 1, THRESH_EXCEED == 0.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_ID: interface ID
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ID: peer ID
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BITMAP: bitmap for TX counters
* Bit0: TX counter unit in MSDU
* Bit1: TX counter unit in MPDU
* Bit2: TX counter unit in PPDU
* Bit3: TX counter unit in byte
* Bit4: Dropped MSDUs
* Bit5: Dropped Bytes
* Bit6: MPDU retry counter
* Bit7: MPDU failure counter
* Bit8: PPDU failure counter
* Bit9: MPDU aggregation counter
* Bit10: MCS counter for ACKed MPDUs
* Bit11: MCS counter for Failed MPDUs
* Bit12: TX Delay counter
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BITMAP: bitmap for RX counters
* Bit0: MAC RX counter unit in MPDU
* Bit1: MAC RX counter unit in byte
* Bit2: PHY RX counter unit in PPDU
* Bit3: PHY RX counter unit in byte
* Bit4: Disorder counter
* Bit5: Retry counter
* Bit6: Duplication counter
* Bit7: Discard counter
* Bit8: MPDU aggregation size counter
* Bit9: MCS counter
* Bit10: Peer STA power state change (wake to sleep) counter
* Bit11: Peer STA power save counter, total time in PS mode
* Bit12: Probe request counter
* Bit13: Other management frames counter
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS_BITMAP: bitmap for CCA
* Bit0: Idle time
* Bit1: TX time
* Bit2: time RX in current bss
* Bit3: Out of current bss time
* Bit4: Wireless medium busy time
* Bit5: RX in bad condition time
* Bit6: TX in bad condition time
* Bit7: time wlan card not available
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_SIGNAL_BITMAP: bitmap for signal
* Bit0: Per channel SNR counter
* Bit1: Per channel noise floor counter
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_NUM: number of peers
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CHANNEL_NUM: number of channels
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_AC_RX_NUM: number of RX stats
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS: per channel BSS CCA stats
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER: container for per PEER stats
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MSDU: Number of total TX MSDUs
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MPDU: Number of total TX MPDUs
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_PPDU: Number of total TX PPDUs
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BYTES: bytes of TX data
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP: Number of dropped TX packets
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP_BYTES: Bytes dropped
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_RETRY: waiting time without an ACK
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_ACK: number of MPDU not-ACKed
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_BACK: number of PPDU not-ACKed
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR_NUM:
* aggregation stats buffer length
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS_NUM: length of mcs stats
* buffer for ACKed MPDUs.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS_NUM: length of mcs stats
* buffer for failed MPDUs.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_DELAY_ARRAY_SIZE:
* length of delay stats array.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR: TX aggregation stats
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS: MCS stats for ACKed MPDUs
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS: MCS stats for failed MPDUs
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DELAY: tx delay stats
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU: MPDUs received
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_BYTES: bytes received
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU: PPDU received
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU_BYTES: PPDU bytes received
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_LOST: packets lost
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_RETRY: number of RX packets
* flagged as retransmissions
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DUP: number of RX packets
* flagged as duplicated
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DISCARD: number of RX
* packets discarded
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR_NUM: length of RX aggregation
* stats buffer.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS_NUM: length of RX mcs
* stats buffer.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS: RX mcs stats buffer
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR: aggregation stats buffer
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_TIMES: times STAs go to sleep
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_DURATION: STAs' total sleep time
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PROBE_REQ: number of probe
* requests received
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MGMT: number of other mgmt
* frames received
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IDLE_TIME: Percentage of idle time
* there is no TX, nor RX, nor interference.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_TIME: percentage of time
* transmitting packets.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_TIME: percentage of time
* for receiving.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BUSY: percentage of time
* interference detected.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BAD: percentage of time
* receiving packets with errors.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BAD: percentage of time
* TX no-ACK.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NO_AVAIL: percentage of time
* the chip is unable to work in normal conditions.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IN_BSS_TIME: percentage of time
* receiving packets in current BSS.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_OUT_BSS_TIME: percentage of time
* receiving packets not in current BSS.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ANT_NUM: number of antennas
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_SIGNAL:
* This is a container for per antenna signal stats.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_SNR: per antenna SNR value
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_NF: per antenna NF value
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_RSSI_BEACON: RSSI of beacon
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_SNR_BEACON: SNR of beacon
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_REPORT_TIME: u64
* Absolute timestamp from 1970/1/1, unit in ms. After receiving the
* message, user layer APP could call gettimeofday to get another
* timestamp and calculate transfer delay for the message.
* @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MEASUREMENT_TIME: u32
* Real period for this measurement, unit in us.
*/
enum qca_wlan_vendor_attr_ll_stats_ext {
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_INVALID = 0,
/* Attributes for configurations */
QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD,
QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD,
/* Peer STA power state change */
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG,
/* TX failure event */
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_STATE,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_MAC_ADDRESS,
/* MAC counters */
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_GLOBAL,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_EVENT_MODE,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_ID,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ID,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BITMAP,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BITMAP,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS_BITMAP,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_SIGNAL_BITMAP,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_NUM,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CHANNEL_NUM,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER,
/* Sub-attributes for PEER_AC_TX */
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MSDU,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MPDU,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_PPDU,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BYTES,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP_BYTES,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_RETRY,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_ACK,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_BACK,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR_NUM,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS_NUM,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS_NUM,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_DELAY_ARRAY_SIZE,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DELAY,
/* Sub-attributes for PEER_AC_RX */
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_BYTES,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU_BYTES,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_LOST,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_RETRY,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DUP,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DISCARD,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR_NUM,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS_NUM,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_TIMES,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_DURATION,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PROBE_REQ,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MGMT,
/* Sub-attributes for CCA_BSS */
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IDLE_TIME,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_TIME,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_TIME,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BUSY,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BAD,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BAD,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NO_AVAIL,
/* sub-attribute for BSS_RX_TIME */
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IN_BSS_TIME,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_OUT_BSS_TIME,
/* Sub-attributes for PEER_SIGNAL */
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ANT_NUM,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_SIGNAL,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_SNR,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_NF,
/* Sub-attributes for IFACE_BSS */
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_RSSI_BEACON,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_SNR_BEACON,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_REPORT_TIME,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MEASUREMENT_TIME,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST,
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MAX =
QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST - 1
};
/* Attributes for FTM commands and events */
/**
* enum qca_wlan_vendor_attr_loc_capa - Indoor location capabilities
*
* @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAGS: Various flags. See
* enum qca_wlan_vendor_attr_loc_capa_flags.
* @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_SESSIONS: Maximum number
* of measurement sessions that can run concurrently.
* Default is one session (no session concurrency).
* @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_PEERS: The total number of unique
* peers that are supported in running sessions. For example,
* if the value is 8 and maximum number of sessions is 2, you can
* have one session with 8 unique peers, or 2 sessions with 4 unique
* peers each, and so on.
* @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_BURSTS_EXP: Maximum number
* of bursts per peer, as an exponent (2^value). Default is 0,
* meaning no multi-burst support.
* @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_MEAS_PER_BURST: Maximum number
* of measurement exchanges allowed in a single burst.
* @QCA_WLAN_VENDOR_ATTR_AOA_CAPA_SUPPORTED_TYPES: Supported AOA measurement
* types. A bit mask (unsigned 32 bit value), each bit corresponds
* to an AOA type as defined by enum qca_vendor_attr_aoa_type.
*/
enum qca_wlan_vendor_attr_loc_capa {
QCA_WLAN_VENDOR_ATTR_LOC_CAPA_INVALID,
QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAGS,
QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_SESSIONS,
QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_PEERS,
QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_BURSTS_EXP,
QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_MEAS_PER_BURST,
QCA_WLAN_VENDOR_ATTR_AOA_CAPA_SUPPORTED_TYPES,
/* keep last */
QCA_WLAN_VENDOR_ATTR_LOC_CAPA_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_LOC_CAPA_MAX =
QCA_WLAN_VENDOR_ATTR_LOC_CAPA_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_loc_capa_flags: Indoor location capability flags
*
* @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_RESPONDER: Set if driver
* can be configured as an FTM responder (for example, an AP that
* services FTM requests). QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER
* will be supported if set.
* @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_INITIATOR: Set if driver
* can run FTM sessions. QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION
* will be supported if set.
* @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_ASAP: Set if FTM responder
* supports immediate (ASAP) response.
* @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA: Set if driver supports standalone
* AOA measurement using QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS.
* @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA_IN_FTM: Set if driver supports
* requesting AOA measurements as part of an FTM session.
*/
enum qca_wlan_vendor_attr_loc_capa_flags {
QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_RESPONDER = 1 << 0,
QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_INITIATOR = 1 << 1,
QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_ASAP = 1 << 2,
QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA = 1 << 3,
QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA_IN_FTM = 1 << 4,
};
/**
* enum qca_wlan_vendor_attr_ftm_peer_info: Information about
* a single peer in a measurement session.
*
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAC_ADDR: The MAC address of the peer.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAGS: Various flags related
* to measurement. See enum qca_wlan_vendor_attr_ftm_peer_meas_flags.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_PARAMS: Nested attribute of
* FTM measurement parameters, as specified by IEEE P802.11-REVmc/D7.0
* 9.4.2.167. See enum qca_wlan_vendor_attr_ftm_meas_param for
* list of supported attributes.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID: Initial token ID for
* secure measurement.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_AOA_BURST_PERIOD: Request AOA
* measurement every <value> bursts. If 0 or not specified,
* AOA measurements will be disabled for this peer.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_FREQ: Frequency in MHz where
* the measurement frames are exchanged. Optional; if not
* specified, try to locate the peer in the kernel scan
* results cache and use frequency from there.
*/
enum qca_wlan_vendor_attr_ftm_peer_info {
QCA_WLAN_VENDOR_ATTR_FTM_PEER_INVALID,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAC_ADDR,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAGS,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_PARAMS,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_AOA_BURST_PERIOD,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_FREQ,
/* keep last */
QCA_WLAN_VENDOR_ATTR_FTM_PEER_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAX =
QCA_WLAN_VENDOR_ATTR_FTM_PEER_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_ftm_peer_meas_flags: Measurement request flags,
* per-peer
*
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_ASAP: If set, request
* immediate (ASAP) response from peer.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCI: If set, request
* LCI report from peer. The LCI report includes the absolute
* location of the peer in "official" coordinates (similar to GPS).
* See IEEE P802.11-REVmc/D7.0, 11.24.6.7 for more information.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCR: If set, request
* Location civic report from peer. The LCR includes the location
* of the peer in free-form format. See IEEE P802.11-REVmc/D7.0,
* 11.24.6.7 for more information.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_SECURE: If set,
* request a secure measurement.
* QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID must also be provided.
*/
enum qca_wlan_vendor_attr_ftm_peer_meas_flags {
QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_ASAP = 1 << 0,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCI = 1 << 1,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCR = 1 << 2,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_SECURE = 1 << 3,
};
/**
* enum qca_wlan_vendor_attr_ftm_meas_param: Measurement parameters
*
* @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MEAS_PER_BURST: Number of measurements
* to perform in a single burst.
* @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_NUM_BURSTS_EXP: Number of bursts to
* perform, specified as an exponent (2^value).
* @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION: Duration of burst
* instance, as specified in IEEE P802.11-REVmc/D7.0, 9.4.2.167.
* @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_PERIOD: Time between bursts,
* as specified in IEEE P802.11-REVmc/D7.0, 9.4.2.167. Must
* be larger than QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION.
*/
enum qca_wlan_vendor_attr_ftm_meas_param {
QCA_WLAN_VENDOR_ATTR_FTM_PARAM_INVALID,
QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MEAS_PER_BURST,
QCA_WLAN_VENDOR_ATTR_FTM_PARAM_NUM_BURSTS_EXP,
QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION,
QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_PERIOD,
/* keep last */
QCA_WLAN_VENDOR_ATTR_FTM_PARAM_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MAX =
QCA_WLAN_VENDOR_ATTR_FTM_PARAM_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_ftm_peer_result: Per-peer results
*
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAC_ADDR: MAC address of the reported
* peer.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS: Status of measurement
* request for this peer.
* See enum qca_wlan_vendor_attr_ftm_peer_result_status.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAGS: Various flags related
* to measurement results for this peer.
* See enum qca_wlan_vendor_attr_ftm_peer_result_flags.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS: Specified when
* request failed and peer requested not to send an additional request
* for this number of seconds.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCI: LCI report when received
* from peer. In the format specified by IEEE P802.11-REVmc/D7.0,
* 9.4.2.22.10.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCR: Location civic report when
* received from peer. In the format specified by IEEE P802.11-REVmc/D7.0,
* 9.4.2.22.13.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAMS: Reported when peer
* overridden some measurement request parameters. See
* enum qca_wlan_vendor_attr_ftm_meas_param.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AOA_MEAS: AOA measurement
* for this peer. Same contents as @QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS: Array of measurement
* results. Each entry is a nested attribute defined
* by enum qca_wlan_vendor_attr_ftm_meas.
*/
enum qca_wlan_vendor_attr_ftm_peer_result {
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_INVALID,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAC_ADDR,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAGS,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCI,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCR,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAMS,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AOA_MEAS,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS,
/* keep last */
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAX =
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_ftm_peer_result_status
*
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_OK: Request sent ok and results
* will be provided. Peer may have overridden some measurement parameters,
* in which case overridden parameters will be report by
* QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAM attribute.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INCAPABLE: Peer is incapable
* of performing the measurement request. No more results will be sent
* for this peer in this session.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_FAILED: Peer reported request
* failed, and requested not to send an additional request for number
* of seconds specified by QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS
* attribute.
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INVALID: Request validation
* failed. Request was not sent over the air.
*/
enum qca_wlan_vendor_attr_ftm_peer_result_status {
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_OK,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INCAPABLE,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_FAILED,
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INVALID,
};
/**
* enum qca_wlan_vendor_attr_ftm_peer_result_flags: Various flags
* for measurement result, per-peer
*
* @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAG_DONE: If set,
* measurement completed for this peer. No more results will be reported
* for this peer in this session.
*/
enum qca_wlan_vendor_attr_ftm_peer_result_flags {
QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAG_DONE = 1 << 0,
};
/**
* enum qca_vendor_attr_loc_session_status: Session completion status code
*
* @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_OK: Session completed
* successfully.
* @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_ABORTED: Session aborted
* by request.
* @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_INVALID: Session request
* was invalid and was not started.
* @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_FAILED: Session had an error
* and did not complete normally (for example out of resources).
*/
enum qca_vendor_attr_loc_session_status {
QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_OK,
QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_ABORTED,
QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_INVALID,
QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_FAILED,
};
/**
* enum qca_wlan_vendor_attr_ftm_meas: Single measurement data
*
* @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T1: Time of departure (TOD) of FTM packet as
* recorded by responder, in picoseconds.
* See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information.
* @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T2: Time of arrival (TOA) of FTM packet at
* initiator, in picoseconds.
* See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information.
* @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T3: TOD of ACK packet as recorded by
* initiator, in picoseconds.
* See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information.
* @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T4: TOA of ACK packet at
* responder, in picoseconds.
* See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information.
* @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_RSSI: RSSI (signal level) as recorded
* during this measurement exchange. Optional and will be provided if
* the hardware can measure it.
* @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOD_ERR: TOD error reported by
* responder. Not always provided.
* See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information.
* @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOA_ERR: TOA error reported by
* responder. Not always provided.
* See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information.
* @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOD_ERR: TOD error measured by
* initiator. Not always provided.
* See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information.
* @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOA_ERR: TOA error measured by
* initiator. Not always provided.
* See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information.
* @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PAD: Dummy attribute for padding.
*/
enum qca_wlan_vendor_attr_ftm_meas {
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INVALID,
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T1,
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T2,
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T3,
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T4,
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_RSSI,
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOD_ERR,
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOA_ERR,
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOD_ERR,
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOA_ERR,
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PAD,
/* keep last */
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_MAX =
QCA_WLAN_VENDOR_ATTR_FTM_MEAS_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_aoa_type - AOA measurement type
*
* @QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE: Phase of the strongest
* CIR (channel impulse response) path for each antenna.
* @QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP: Phase and amplitude
* of the strongest CIR path for each antenna.
*/
enum qca_wlan_vendor_attr_aoa_type {
QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE,
QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP,
QCA_WLAN_VENDOR_ATTR_AOA_TYPE_MAX
};
/**
* enum qca_wlan_vendor_attr_encryption_test - Attributes to
* validate encryption engine
*
* @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_NEEDS_DECRYPTION: Flag attribute.
* This will be included if the request is for decryption; if not included,
* the request is treated as a request for encryption by default.
* @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_CIPHER: Unsigned 32-bit value
* indicating the key cipher suite. Takes same values as
* NL80211_ATTR_KEY_CIPHER.
* @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_KEYID: Unsigned 8-bit value
* Key Id to be used for encryption
* @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_TK: Array of 8-bit values.
* Key (TK) to be used for encryption/decryption
* @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_PN: Array of 8-bit values.
* Packet number to be specified for encryption/decryption
* 6 bytes for TKIP/CCMP/GCMP.
* @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_DATA: Array of 8-bit values
* representing the 802.11 packet (header + payload + FCS) that
* needs to be encrypted/decrypted.
* Encrypted/decrypted response from the driver will also be sent
* to userspace with the same attribute.
*/
enum qca_wlan_vendor_attr_encryption_test {
QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_NEEDS_DECRYPTION,
QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_CIPHER,
QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_KEYID,
QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_TK,
QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_PN,
QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_DATA,
/* keep last */
QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_MAX =
QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_AFTER_LAST - 1
};
/**
* enum qca_wlan_vendor_attr_dmg_rf_sector_type - Type of
* sector for DMG RF sector operations.
*
* @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_RX: RX sector
* @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_TX: TX sector
*/
enum qca_wlan_vendor_attr_dmg_rf_sector_type {
QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_RX,
QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_TX,
QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_MAX
};
/**
* enum qca_wlan_vendor_attr_fw_state - State of firmware
*
* @QCA_WLAN_VENDOR_ATTR_FW_STATE_ERROR: FW is in bad state
* @QCA_WLAN_VENDOR_ATTR_FW_STATE_ACTIVE: FW is active
*/
enum qca_wlan_vendor_attr_fw_state {
QCA_WLAN_VENDOR_ATTR_FW_STATE_ERROR,
QCA_WLAN_VENDOR_ATTR_FW_STATE_ACTIVE,
QCA_WLAN_VENDOR_ATTR_FW_STATE_MAX
};
/**
* BRP antenna limit mode
*
* @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_DISABLE: Disable BRP force
* antenna limit, BRP will be performed as usual.
* @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_EFFECTIVE: Define maximal
* antennas limit. the hardware may use less antennas than the
* maximum limit.
* @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_FORCE: The hardware will
* use exactly the specified number of antennas for BRP.
*/
enum qca_wlan_vendor_attr_brp_ant_limit_mode {
QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_DISABLE,
QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_EFFECTIVE,
QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_FORCE,
QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_MAX
};
/**
* enum qca_wlan_vendor_attr_dmg_rf_sector_cfg - Attributes for
* DMG RF sector configuration for a single RF module.
* The values are defined in a compact way which closely matches
* the way it is stored in HW registers.
* The configuration provides values for 32 antennas and 8 distribution
* amplifiers, and together describes the characteristics of the RF
* sector - such as a beam in some direction with some gain.
*
* @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MODULE_INDEX: Index
* of RF module for this configuration.
* @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE0: Bit 0 of edge
* amplifier gain index. Unsigned 32 bit number containing
* bits for all 32 antennas.
* @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE1: Bit 1 of edge
* amplifier gain index. Unsigned 32 bit number containing
* bits for all 32 antennas.
* @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE2: Bit 2 of edge
* amplifier gain index. Unsigned 32 bit number containing
* bits for all 32 antennas.
* @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_HI: Phase values
* for first 16 antennas, 2 bits per antenna.
* @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_LO: Phase values
* for last 16 antennas, 2 bits per antenna.
* @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_DTYPE_X16: Contains
* DTYPE values (3 bits) for each distribution amplifier, followed
* by X16 switch bits for each distribution amplifier. There are
* total of 8 distribution amplifiers.
*/
enum qca_wlan_vendor_attr_dmg_rf_sector_cfg {
QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MODULE_INDEX = 1,
QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE0 = 2,
QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE1 = 3,
QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE2 = 4,
QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_HI = 5,
QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_LO = 6,
QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_DTYPE_X16 = 7,
/* keep last */
QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MAX =
QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_AFTER_LAST - 1
};
enum qca_wlan_vendor_attr_ll_stats_set {
QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_INVALID = 0,
/* Unsigned 32-bit value */
QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_CONFIG_MPDU_SIZE_THRESHOLD = 1,
QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_CONFIG_AGGRESSIVE_STATS_GATHERING = 2,
/* keep last */
QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_MAX =
QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_AFTER_LAST - 1,
};
enum qca_wlan_vendor_attr_ll_stats_clr {
QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_INVALID = 0,
/* Unsigned 32bit bitmap for clearing statistics
* All radio statistics 0x00000001
* cca_busy_time (within radio statistics) 0x00000002
* All channel stats (within radio statistics) 0x00000004
* All scan statistics (within radio statistics) 0x00000008
* All interface statistics 0x00000010
* All tx rate statistics (within interface statistics) 0x00000020
* All ac statistics (with in interface statistics) 0x00000040
* All contention (min, max, avg) statistics (within ac statisctics)
* 0x00000080.
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_REQ_MASK = 1,
/* Unsigned 8 bit value: Request to stop statistics collection */
QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_REQ = 2,
/* Unsigned 32 bit bitmap: Response from the driver
* for the cleared statistics
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_RSP_MASK = 3,
/* Unsigned 8 bit value: Response from driver/firmware
* for the stop request
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_RSP = 4,
/* keep last */
QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_MAX =
QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_AFTER_LAST - 1,
};
enum qca_wlan_vendor_attr_ll_stats_get {
QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_INVALID = 0,
/* Unsigned 32 bit value provided by the caller issuing the GET stats
* command. When reporting the stats results, the driver uses the same
* value to indicate which GET request the results correspond to.
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_ID = 1,
/* Unsigned 32 bit value - bit mask to identify what statistics are
* requested for retrieval.
* Radio Statistics 0x00000001
* Interface Statistics 0x00000020
* All Peer Statistics 0x00000040
* Peer Statistics 0x00000080
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_MASK = 2,
/* keep last */
QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_MAX =
QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_AFTER_LAST - 1,
};
enum qca_wlan_vendor_attr_ll_stats_results {
QCA_WLAN_VENDOR_ATTR_LL_STATS_INVALID = 0,
/* Unsigned 32bit value. Used by the driver; must match the request id
* provided with the QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET command.
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_RESULTS_REQ_ID = 1,
/* Unsigned 32 bit value */
QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_BEACON_RX = 2,
/* Unsigned 32 bit value */
QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_RX = 3,
/* Unsigned 32 bit value */
QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_ACTION_RX = 4,
/* Unsigned 32 bit value */
QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_ACTION_TX = 5,
/* Signed 32 bit value */
QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_MGMT = 6,
/* Signed 32 bit value */
QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_DATA = 7,
/* Signed 32 bit value */
QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_ACK = 8,
/* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_* are
* nested within the interface stats.
*/
/* Interface mode, e.g., STA, SOFTAP, IBSS, etc.
* Type = enum wifi_interface_mode.
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_MODE = 9,
/* Interface MAC address. An array of 6 Unsigned int8 */
QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_MAC_ADDR = 10,
/* Type = enum wifi_connection_state, e.g., DISCONNECTED,
* AUTHENTICATING, etc. valid for STA, CLI only.
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_STATE = 11,
/* Type = enum wifi_roam_state. Roaming state, e.g., IDLE or ACTIVE
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_ROAMING = 12,
/* Unsigned 32 bit value. WIFI_CAPABILITY_XXX */
QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_CAPABILITIES = 13,
/* NULL terminated SSID. An array of 33 Unsigned 8bit values */
QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_SSID = 14,
/* BSSID. An array of 6 unsigned 8 bit values */
QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_BSSID = 15,
/* Country string advertised by AP. An array of 3 unsigned 8 bit
* values.
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_AP_COUNTRY_STR = 16,
/* Country string for this association. An array of 3 unsigned 8 bit
* values.
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_COUNTRY_STR = 17,
/* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_* could
* be nested within the interface stats.
*/
/* Type = enum wifi_traffic_ac, e.g., V0, VI, BE and BK */
QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_AC = 18,
/* Unsigned int 32 value corresponding to respective AC */
QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_MPDU = 19,
/* Unsigned int 32 value corresponding to respective AC */
QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_MPDU = 20,
/* Unsigned int 32 value corresponding to respective AC */
QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_MCAST = 21,
/* Unsigned int 32 value corresponding to respective AC */
QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_MCAST = 22,
/* Unsigned int 32 value corresponding to respective AC */
QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_AMPDU = 23,
/* Unsigned int 32 value corresponding to respective AC */
QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_AMPDU = 24,
/* Unsigned int 32 value corresponding to respective AC */
QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_MPDU_LOST = 25,
/* Unsigned int 32 value corresponding to respective AC */
QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES = 26,
/* Unsigned int 32 value corresponding to respective AC */
QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES_SHORT = 27,
/* Unsigned int 32 values corresponding to respective AC */
QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES_LONG = 28,
/* Unsigned int 32 values corresponding to respective AC */
QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_MIN = 29,
/* Unsigned int 32 values corresponding to respective AC */
QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_MAX = 30,
/* Unsigned int 32 values corresponding to respective AC */
QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_AVG = 31,
/* Unsigned int 32 values corresponding to respective AC */
QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_NUM_SAMPLES = 32,
/* Unsigned 32 bit value. Number of peers */
QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_NUM_PEERS = 33,
/* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_* are
* nested within the interface stats.
*/
/* Type = enum wifi_peer_type. Peer type, e.g., STA, AP, P2P GO etc. */
QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_TYPE = 34,
/* MAC addr corresponding to respective peer. An array of 6 unsigned
* 8 bit values.
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_MAC_ADDRESS = 35,
/* Unsigned int 32 bit value representing capabilities corresponding
* to respective peer.
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_CAPABILITIES = 36,
/* Unsigned 32 bit value. Number of rates */
QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_NUM_RATES = 37,
/* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_*
* are nested within the rate stat.
*/
/* Wi-Fi Rate - separate attributes defined for individual fields */
/* Unsigned int 8 bit value; 0: OFDM, 1:CCK, 2:HT 3:VHT 4..7 reserved */
QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_PREAMBLE = 38,
/* Unsigned int 8 bit value; 0:1x1, 1:2x2, 3:3x3, 4:4x4 */
QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_NSS = 39,
/* Unsigned int 8 bit value; 0:20 MHz, 1:40 MHz, 2:80 MHz, 3:160 MHz */
QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_BW = 40,
/* Unsigned int 8 bit value; OFDM/CCK rate code would be as per IEEE Std
* in the units of 0.5 Mbps HT/VHT it would be MCS index
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_MCS_INDEX = 41,
/* Unsigned 32 bit value. Bit rate in units of 100 kbps */
QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_BIT_RATE = 42,
/* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_STAT_* could be
* nested within the peer info stats.
*/
/* Unsigned int 32 bit value. Number of successfully transmitted data
* packets, i.e., with ACK received corresponding to the respective
* rate.
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_TX_MPDU = 43,
/* Unsigned int 32 bit value. Number of received data packets
* corresponding to the respective rate.
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RX_MPDU = 44,
/* Unsigned int 32 bit value. Number of data packet losses, i.e., no ACK
* received corresponding to the respective rate.
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_MPDU_LOST = 45,
/* Unsigned int 32 bit value. Total number of data packet retries for
* the respective rate.
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES = 46,
/* Unsigned int 32 bit value. Total number of short data packet retries
* for the respective rate.
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES_SHORT = 47,
/* Unsigned int 32 bit value. Total number of long data packet retries
* for the respective rate.
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES_LONG = 48,
QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ID = 49,
/* Unsigned 32 bit value. Total number of msecs the radio is awake
* accruing over time.
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME = 50,
/* Unsigned 32 bit value. Total number of msecs the radio is
* transmitting accruing over time.
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_TX_TIME = 51,
/* Unsigned 32 bit value. Total number of msecs the radio is in active
* receive accruing over time.
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_RX_TIME = 52,
/* Unsigned 32 bit value. Total number of msecs the radio is awake due
* to all scan accruing over time.
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_SCAN = 53,
/* Unsigned 32 bit value. Total number of msecs the radio is awake due
* to NAN accruing over time.
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_NBD = 54,
/* Unsigned 32 bit value. Total number of msecs the radio is awake due
* to GSCAN accruing over time.
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_GSCAN = 55,
/* Unsigned 32 bit value. Total number of msecs the radio is awake due
* to roam scan accruing over time.
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_ROAM_SCAN = 56,
/* Unsigned 32 bit value. Total number of msecs the radio is awake due
* to PNO scan accruing over time.
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_PNO_SCAN = 57,
/* Unsigned 32 bit value. Total number of msecs the radio is awake due
* to Hotspot 2.0 scans and GAS exchange accruing over time.
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_HS20 = 58,
/* Unsigned 32 bit value. Number of channels. */
QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_NUM_CHANNELS = 59,
/* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_* could
* be nested within the channel stats.
*/
/* Type = enum wifi_channel_width. Channel width, e.g., 20, 40, 80 */
QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_WIDTH = 60,
/* Unsigned 32 bit value. Primary 20 MHz channel. */
QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ = 61,
/* Unsigned 32 bit value. Center frequency (MHz) first segment. */
QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ0 = 62,
/* Unsigned 32 bit value. Center frequency (MHz) second segment. */
QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ1 = 63,
/* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_* could be
* nested within the radio stats.
*/
/* Unsigned int 32 bit value representing total number of msecs the
* radio is awake on that channel accruing over time, corresponding to
* the respective channel.
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_ON_TIME = 64,
/* Unsigned int 32 bit value representing total number of msecs the CCA
* register is busy accruing over time corresponding to the respective
* channel.
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_CCA_BUSY_TIME = 65,
QCA_WLAN_VENDOR_ATTR_LL_STATS_NUM_RADIOS = 66,
/* Signifies the nested list of channel attributes
* QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_*
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_CH_INFO = 67,
/* Signifies the nested list of peer info attributes
* QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_*
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO = 68,
/* Signifies the nested list of rate info attributes
* QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_*
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_RATE_INFO = 69,
/* Signifies the nested list of wmm info attributes
* QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_*
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_INFO = 70,
/* Unsigned 8 bit value. Used by the driver; if set to 1, it indicates
* that more stats, e.g., peers or radio, are to follow in the next
* QCA_NL80211_VENDOR_SUBCMD_LL_STATS_*_RESULTS event.
* Otherwise, it is set to 0.
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_RESULTS_MORE_DATA = 71,
/* Unsigned 64 bit value */
QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_AVERAGE_TSF_OFFSET = 72,
/* Unsigned 32 bit value */
QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_DETECTED = 73,
/* Unsigned 32 bit value */
QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_AVG_NUM_FRAMES_LEAKED = 74,
/* Unsigned 32 bit value */
QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_GUARD_TIME = 75,
/* Unsigned 32 bit value */
QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE = 76,
/* Unsigned 32 bit value */
QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_NUM_TX_LEVELS = 77,
/* Number of msecs the radio spent in transmitting for each power level
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_TX_TIME_PER_LEVEL = 78,
/* Unsigned 32 bit value */
QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RTS_SUCC_CNT = 79,
/* Unsigned 32 bit value */
QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RTS_FAIL_CNT = 80,
/* Unsigned 32 bit value */
QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_PPDU_SUCC_CNT = 81,
/* Unsigned 32 bit value */
QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_PPDU_FAIL_CNT = 82,
/* Unsigned int 32 value.
* Pending MSDUs corresponding to respective AC.
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_PENDING_MSDU = 83,
/* keep last */
QCA_WLAN_VENDOR_ATTR_LL_STATS_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_LL_STATS_MAX =
QCA_WLAN_VENDOR_ATTR_LL_STATS_AFTER_LAST - 1,
};
enum qca_wlan_vendor_attr_ll_stats_type {
QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_INVALID = 0,
QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_RADIO = 1,
QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_IFACE = 2,
QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_PEERS = 3,
/* keep last */
QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_AFTER_LAST,
QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_MAX =
QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_tdls_configuration - Attributes for
* TDLS configuration to the host driver.
*
* @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE: Configure the TDLS trigger
* mode in the host driver. enum qca_wlan_vendor_tdls_trigger_mode
* represents the different TDLS trigger modes.
* @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD: Duration (u32) within
* which QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD number
* of packets shall meet the criteria for implicit TDLS setup.
* @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD: Number (u32) of Tx/Rx packets
* within a duration QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD
* to initiate a TDLS setup.
* @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_DISCOVERY_PERIOD: Time (u32) to initiate
* a TDLS Discovery to the peer.
* @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX_DISCOVERY_ATTEMPT: Max number (u32) of
* discovery attempts to know the TDLS capability of the peer. A peer is
* marked as TDLS not capable if there is no response for all the attempts.
* @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT: Represents a duration (u32)
* within which QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD
* number of TX / RX frames meet the criteria for TDLS teardown.
* @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD: Minimum number (u32)
* of Tx/Rx packets within a duration
* QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT to tear down a TDLS link.
* @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_SETUP_RSSI_THRESHOLD: Threshold
* corresponding to the RSSI of the peer below which a TDLS setup is
* triggered.
* @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TEARDOWN_RSSI_THRESHOLD: Threshold
* corresponding to the RSSI of the peer above which a TDLS teardown is
* triggered.
*/
enum qca_wlan_vendor_attr_tdls_configuration {
QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE = 1,
/* Attributes configuring the TDLS Implicit Trigger */
QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD = 2,
QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD = 3,
QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_DISCOVERY_PERIOD = 4,
QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX_DISCOVERY_ATTEMPT = 5,
QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT = 6,
QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD = 7,
QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_SETUP_RSSI_THRESHOLD = 8,
QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TEARDOWN_RSSI_THRESHOLD = 9,
/* keep last */
QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX =
QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_AFTER_LAST - 1
};
/**
* enum qca_wlan_vendor_tdls_trigger_mode: Represents the TDLS trigger mode in
* the driver
*
* The following are the different values for
* QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE.
*
* @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXPLICIT: The trigger to initiate/teardown
* the TDLS connection to a respective peer comes from the user space.
* wpa_supplicant provides the commands TDLS_SETUP, TDLS_TEARDOWN,
* TDLS_DISCOVER to do this.
* @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_IMPLICIT: Host driver triggers this TDLS
* setup/teardown to the eligible peer once the configured criteria
* (such as TX/RX threshold, RSSI) is met. The attributes
* in QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IMPLICIT_PARAMS correspond to
* the different configuration criteria for the TDLS trigger from the
* host driver.
* @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXTERNAL: Enables the driver to trigger
* the TDLS setup / teardown through the implicit mode only to the
* configured MAC addresses (wpa_supplicant, with tdls_external_control=1,
* configures the MAC address through TDLS_SETUP / TDLS_TEARDOWN commands).
* External mode works on top of the implicit mode. Thus the host driver
* is expected to configure in TDLS Implicit mode too to operate in
* External mode.
* Configuring External mode alone without Implicit mode is invalid.
*
* All the above implementations work as expected only when the host driver
* advertises the capability WPA_DRIVER_FLAGS_TDLS_EXTERNAL_SETUP - representing
* that the TDLS message exchange is not internal to the host driver, but
* depends on wpa_supplicant to do the message exchange.
*/
enum qca_wlan_vendor_tdls_trigger_mode {
QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXPLICIT = 1 << 0,
QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_IMPLICIT = 1 << 1,
QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXTERNAL = 1 << 2,
};
/**
* enum qca_vendor_attr_sar_limits_selections - Source of SAR power limits
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF0: Select SAR profile #0
* that is hard-coded in the Board Data File (BDF).
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF1: Select SAR profile #1
* that is hard-coded in the Board Data File (BDF).
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF2: Select SAR profile #2
* that is hard-coded in the Board Data File (BDF).
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF3: Select SAR profile #3
* that is hard-coded in the Board Data File (BDF).
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF4: Select SAR profile #4
* that is hard-coded in the Board Data File (BDF).
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_NONE: Do not select any
* source of SAR power limits, thereby disabling the SAR power
* limit feature.
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER: Select the SAR power
* limits configured by %QCA_NL80211_VENDOR_SUBCMD_SET_SAR.
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0: Select the SAR power
* limits version 2.0 configured by %QCA_NL80211_VENDOR_SUBCMD_SET_SAR.
*
* This enumerates the valid set of values that may be supplied for
* attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT in an instance of
* the %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS vendor command or in
* the response to an instance of the
* %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS vendor command.
*/
enum qca_vendor_attr_sar_limits_selections {
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF0 = 0,
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF1 = 1,
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF2 = 2,
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF3 = 3,
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF4 = 4,
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_NONE = 5,
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER = 6,
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0 = 7,
};
/**
* enum qca_vendor_attr_sar_limits_spec_modulations -
* SAR limits specification modulation
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_CCK -
* CCK modulation
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_OFDM -
* OFDM modulation
*
* This enumerates the valid set of values that may be supplied for
* attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION in an
* instance of attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC in an
* instance of the %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS vendor
* command or in the response to an instance of the
* %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS vendor command.
*/
enum qca_vendor_attr_sar_limits_spec_modulations {
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_CCK = 0,
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_OFDM = 1,
};
/**
* enum qca_vendor_attr_sar_limits - Attributes for SAR power limits
*
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE: Optional (u32) value to
* select which SAR power limit table should be used. Valid
* values are enumerated in enum
* %qca_vendor_attr_sar_limits_selections. The existing SAR
* power limit selection is unchanged if this attribute is not
* present.
*
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS: Optional (u32) value
* which specifies the number of SAR power limit specifications
* which will follow.
*
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC: Nested array of SAR power
* limit specifications. The number of specifications is
* specified by @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS. Each
* specification contains a set of
* QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_* attributes. A
* specification is uniquely identified by the attributes
* %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND,
* %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN, and
* %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION and always
* contains as a payload the attribute
* %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT,
* %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX.
* Either %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT or
* %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX is
* needed based upon the value of
* %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE.
*
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND: Optional (u32) value to
* indicate for which band this specification applies. Valid
* values are enumerated in enum %nl80211_band (although not all
* bands may be supported by a given device). If the attribute is
* not supplied then the specification will be applied to all
* supported bands.
*
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN: Optional (u32) value
* to indicate for which antenna chain this specification
* applies, i.e. 1 for chain 1, 2 for chain 2, etc. If the
* attribute is not supplied then the specification will be
* applied to all chains.
*
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION: Optional (u32)
* value to indicate for which modulation scheme this
* specification applies. Valid values are enumerated in enum
* %qca_vendor_attr_sar_limits_spec_modulations. If the attribute
* is not supplied then the specification will be applied to all
* modulation schemes.
*
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT: Required (u32)
* value to specify the actual power limit value in units of 0.5
* dBm (i.e., a value of 11 represents 5.5 dBm).
* This is required, when %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT is
* %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER.
*
* @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX: Required (u32)
* value to indicate SAR V2 indices (0 - 11) to select SAR V2 profiles.
* This is required, when %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT is
* %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0.
*
* These attributes are used with %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS
* and %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS.
*/
enum qca_vendor_attr_sar_limits {
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE = 1,
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS = 2,
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC = 3,
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND = 4,
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN = 5,
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION = 6,
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT = 7,
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX = 8,
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_MAX =
QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_AFTER_LAST - 1
};
/**
* enum qca_wlan_vendor_attr_get_wifi_info: Attributes for data used by
* QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO sub command.
*/
enum qca_wlan_vendor_attr_get_wifi_info {
QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_WIFI_INFO_DRIVER_VERSION = 1,
QCA_WLAN_VENDOR_ATTR_WIFI_INFO_FIRMWARE_VERSION = 2,
/* keep last */
QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_MAX =
QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST - 1,
};
/*
* enum qca_wlan_vendor_attr_wifi_logger_start: Attributes for data used by
* QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_START sub command.
*/
enum qca_wlan_vendor_attr_wifi_logger_start {
QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_RING_ID = 1,
QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_VERBOSE_LEVEL = 2,
QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_FLAGS = 3,
/* keep last */
QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_GET_MAX =
QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST - 1,
};
enum qca_wlan_vendor_attr_logger_results {
QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_INVALID = 0,
/* Unsigned 32-bit value; must match the request Id supplied by
* Wi-Fi HAL in the corresponding subcmd NL msg.
*/
QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_REQUEST_ID = 1,
/* Unsigned 32-bit value; used to indicate the size of memory
* dump to be allocated.
*/
QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_MEMDUMP_SIZE = 2,
/* keep last */
QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_MAX =
QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_AFTER_LAST - 1,
};
enum qca_wlan_vendor_attr_roaming_config_params {
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_ROAMING_SUBCMD = 1,
QCA_WLAN_VENDOR_ATTR_ROAMING_REQ_ID = 2,
/* Attributes for wifi_set_ssid_white_list */
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_NUM_NETWORKS = 3,
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_LIST = 4,
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID = 5,
/* Attributes for set_roam_params */
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_THRESHOLD = 6,
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_THRESHOLD = 7,
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_FACTOR = 8,
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_FACTOR = 9,
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_MAX_BOOST = 10,
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_LAZY_ROAM_HISTERESYS = 11,
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALERT_ROAM_RSSI_TRIGGER = 12,
/* Attribute for set_lazy_roam */
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_ENABLE = 13,
/* Attribute for set_lazy_roam with preferences */
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PREFS = 14,
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_NUM_BSSID = 15,
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_BSSID = 16,
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_RSSI_MODIFIER = 17,
/* Attribute for set_blacklist bssid params */
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS = 18,
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_NUM_BSSID = 19,
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_BSSID = 20,
/* Flag attribute indicates this BSSID blacklist as a hint */
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_HINT = 21,
/* keep last */
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_MAX =
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST - 1,
};
/*
* enum qca_wlan_vendor_attr_roam_subcmd: Attributes for data used by
* QCA_NL80211_VENDOR_SUBCMD_ROAM sub command.
*/
enum qca_wlan_vendor_attr_roam_subcmd {
QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SSID_WHITE_LIST = 1,
QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_GSCAN_ROAM_PARAMS = 2,
QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_LAZY_ROAM = 3,
QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BSSID_PREFS = 4,
QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BSSID_PARAMS = 5,
QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BLACKLIST_BSSID = 6,
/* keep last */
QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_MAX =
QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_AFTER_LAST - 1,
};
enum qca_wlan_vendor_attr_gscan_config_params {
QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_INVALID = 0,
/* Unsigned 32-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_REQUEST_ID = 1,
/* Attributes for data used by
* QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_VALID_CHANNELS sub command.
*/
/* Unsigned 32-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_GET_VALID_CHANNELS_CONFIG_PARAM_WIFI_BAND
= 2,
/* Unsigned 32-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_GET_VALID_CHANNELS_CONFIG_PARAM_MAX_CHANNELS
= 3,
/* Attributes for input params used by
* QCA_NL80211_VENDOR_SUBCMD_GSCAN_START sub command.
*/
/* Unsigned 32-bit value; channel frequency */
QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_CHANNEL = 4,
/* Unsigned 32-bit value; dwell time in ms. */
QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_DWELL_TIME = 5,
/* Unsigned 8-bit value; 0: active; 1: passive; N/A for DFS */
QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_PASSIVE = 6,
/* Unsigned 8-bit value; channel class */
QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_CLASS = 7,
/* Unsigned 8-bit value; bucket index, 0 based */
QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_INDEX = 8,
/* Unsigned 8-bit value; band. */
QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_BAND = 9,
/* Unsigned 32-bit value; desired period, in ms. */
QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_PERIOD = 10,
/* Unsigned 8-bit value; report events semantics. */
QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_REPORT_EVENTS = 11,
/* Unsigned 32-bit value. Followed by a nested array of
* GSCAN_CHANNEL_SPEC_* attributes.
*/
QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS = 12,
/* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_* attributes.
* Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS
*/
QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC = 13,
/* Unsigned 32-bit value; base timer period in ms. */
QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_BASE_PERIOD = 14,
/* Unsigned 32-bit value; number of APs to store in each scan in the
* BSSID/RSSI history buffer (keep the highest RSSI APs).
*/
QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_MAX_AP_PER_SCAN = 15,
/* Unsigned 8-bit value; in %, when scan buffer is this much full, wake
* up AP.
*/
QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_REPORT_THRESHOLD_PERCENT
= 16,
/* Unsigned 8-bit value; number of scan bucket specs; followed by a
* nested array of_GSCAN_BUCKET_SPEC_* attributes and values. The size
* of the array is determined by NUM_BUCKETS.
*/
QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_NUM_BUCKETS = 17,
/* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_* attributes.
* Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_NUM_BUCKETS
*/
QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC = 18,
/* Unsigned 8-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_GET_CACHED_SCAN_RESULTS_CONFIG_PARAM_FLUSH
= 19,
/* Unsigned 32-bit value; maximum number of results to be returned. */
QCA_WLAN_VENDOR_ATTR_GSCAN_GET_CACHED_SCAN_RESULTS_CONFIG_PARAM_MAX
= 20,
/* An array of 6 x unsigned 8-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_BSSID = 21,
/* Signed 32-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_RSSI_LOW = 22,
/* Signed 32-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_RSSI_HIGH = 23,
/* Unsigned 32-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_CHANNEL = 24,
/* Number of hotlist APs as unsigned 32-bit value, followed by a nested
* array of AP_THRESHOLD_PARAM attributes and values. The size of the
* array is determined by NUM_AP.
*/
QCA_WLAN_VENDOR_ATTR_GSCAN_BSSID_HOTLIST_PARAMS_NUM_AP = 25,
/* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_* attributes.
* Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS
*/
QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM = 26,
/* Unsigned 32-bit value; number of samples for averaging RSSI. */
QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_RSSI_SAMPLE_SIZE
= 27,
/* Unsigned 32-bit value; number of samples to confirm AP loss. */
QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_LOST_AP_SAMPLE_SIZE
= 28,
/* Unsigned 32-bit value; number of APs breaching threshold. */
QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_MIN_BREACHING = 29,
/* Unsigned 32-bit value; number of APs. Followed by an array of
* AP_THRESHOLD_PARAM attributes. Size of the array is NUM_AP.
*/
QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_NUM_AP = 30,
/* Unsigned 32-bit value; number of samples to confirm AP loss. */
QCA_WLAN_VENDOR_ATTR_GSCAN_BSSID_HOTLIST_PARAMS_LOST_AP_SAMPLE_SIZE
= 31,
/* Unsigned 32-bit value. If max_period is non zero or different than
* period, then this bucket is an exponential backoff bucket.
*/
QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_MAX_PERIOD = 32,
/* Unsigned 32-bit value. */
QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_BASE = 33,
/* Unsigned 32-bit value. For exponential back off bucket, number of
* scans to perform for a given period.
*/
QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_STEP_COUNT = 34,
/* Unsigned 8-bit value; in number of scans, wake up AP after these
* many scans.
*/
QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_REPORT_THRESHOLD_NUM_SCANS
= 35,
/* Attributes for data used by
* QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SSID_HOTLIST sub command.
*/
/* Unsigned 3-2bit value; number of samples to confirm SSID loss. */
QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_LOST_SSID_SAMPLE_SIZE
= 36,
/* Number of hotlist SSIDs as unsigned 32-bit value, followed by a
* nested array of SSID_THRESHOLD_PARAM_* attributes and values. The
* size of the array is determined by NUM_SSID.
*/
QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_NUM_SSID = 37,
/* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_*
* attributes.
* Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_NUM_SSID
*/
QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM = 38,
/* An array of 33 x unsigned 8-bit value; NULL terminated SSID */
QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_SSID = 39,
/* Unsigned 8-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_BAND = 40,
/* Signed 32-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_RSSI_LOW = 41,
/* Signed 32-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_RSSI_HIGH = 42,
/* Unsigned 32-bit value; a bitmask with additional gscan config flag.
*/
QCA_WLAN_VENDOR_ATTR_GSCAN_CONFIGURATION_FLAGS = 43,
/* keep last */
QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_MAX =
QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_AFTER_LAST - 1,
};
enum qca_wlan_vendor_attr_gscan_results {
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_INVALID = 0,
/* Unsigned 32-bit value; must match the request Id supplied by
* Wi-Fi HAL in the corresponding subcmd NL msg.
*/
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_REQUEST_ID = 1,
/* Unsigned 32-bit value; used to indicate the status response from
* firmware/driver for the vendor sub-command.
*/
QCA_WLAN_VENDOR_ATTR_GSCAN_STATUS = 2,
/* GSCAN Valid Channels attributes */
/* Unsigned 32bit value; followed by a nested array of CHANNELS. */
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_CHANNELS = 3,
/* An array of NUM_CHANNELS x unsigned 32-bit value integers
* representing channel numbers.
*/
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CHANNELS = 4,
/* GSCAN Capabilities attributes */
/* Unsigned 32-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_CACHE_SIZE = 5,
/* Unsigned 32-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_BUCKETS = 6,
/* Unsigned 32-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_AP_CACHE_PER_SCAN
= 7,
/* Unsigned 32-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_RSSI_SAMPLE_SIZE
= 8,
/* Signed 32-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_REPORTING_THRESHOLD
= 9,
/* Unsigned 32-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_HOTLIST_BSSIDS = 10,
/* Unsigned 32-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SIGNIFICANT_WIFI_CHANGE_APS
= 11,
/* Unsigned 32-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_BSSID_HISTORY_ENTRIES
= 12,
/* GSCAN Attributes used with
* QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_RESULTS_AVAILABLE sub-command.
*/
/* Unsigned 32-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE = 13,
/* GSCAN attributes used with
* QCA_NL80211_VENDOR_SUBCMD_GSCAN_FULL_SCAN_RESULT sub-command.
*/
/* An array of NUM_RESULTS_AVAILABLE x
* QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_*
*/
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST = 14,
/* Unsigned 64-bit value; age of sample at the time of retrieval */
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_TIME_STAMP = 15,
/* 33 x unsigned 8-bit value; NULL terminated SSID */
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_SSID = 16,
/* An array of 6 x unsigned 8-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_BSSID = 17,
/* Unsigned 32-bit value; channel frequency in MHz */
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_CHANNEL = 18,
/* Signed 32-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RSSI = 19,
/* Unsigned 32-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RTT = 20,
/* Unsigned 32-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RTT_SD = 21,
/* Unsigned 16-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_BEACON_PERIOD = 22,
/* Unsigned 16-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_CAPABILITY = 23,
/* Unsigned 32-bit value; size of the IE DATA blob */
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_IE_LENGTH = 24,
/* An array of IE_LENGTH x unsigned 8-bit value; blob of all the
* information elements found in the beacon; this data should be a
* packed list of wifi_information_element objects, one after the
* other.
*/
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_IE_DATA = 25,
/* Unsigned 8-bit value; set by driver to indicate more scan results are
* available.
*/
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_MORE_DATA = 26,
/* GSCAN attributes for
* QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_EVENT sub-command.
*/
/* Unsigned 8-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_EVENT_TYPE = 27,
/* Unsigned 32-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_EVENT_STATUS = 28,
/* GSCAN attributes for
* QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_FOUND sub-command.
*/
/* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE
* to indicate number of results.
* Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the
* list of results.
*/
/* GSCAN attributes for
* QCA_NL80211_VENDOR_SUBCMD_GSCAN_SIGNIFICANT_CHANGE sub-command.
*/
/* An array of 6 x unsigned 8-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_BSSID = 29,
/* Unsigned 32-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_CHANNEL
= 30,
/* Unsigned 32-bit value. */
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_NUM_RSSI
= 31,
/* A nested array of signed 32-bit RSSI values. Size of the array is
* determined by (NUM_RSSI of SIGNIFICANT_CHANGE_RESULT_NUM_RSSI.
*/
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_RSSI_LIST
= 32,
/* GSCAN attributes used with
* QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CACHED_RESULTS sub-command.
*/
/* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE
* to indicate number of gscan cached results returned.
* Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_LIST to indicate
* the list of gscan cached results.
*/
/* An array of NUM_RESULTS_AVAILABLE x
* QCA_NL80211_VENDOR_ATTR_GSCAN_CACHED_RESULTS_*
*/
QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_LIST = 33,
/* Unsigned 32-bit value; a unique identifier for the scan unit. */
QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_SCAN_ID = 34,
/* Unsigned 32-bit value; a bitmask w/additional information about scan.
*/
QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_FLAGS = 35,
/* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE
* to indicate number of wifi scan results/bssids retrieved by the scan.
* Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the
* list of wifi scan results returned for each cached result block.
*/
/* GSCAN attributes for
* QCA_NL80211_VENDOR_SUBCMD_PNO_NETWORK_FOUND sub-command.
*/
/* Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE for
* number of results.
* Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the nested
* list of wifi scan results returned for each
* wifi_passpoint_match_result block.
* Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE.
*/
/* GSCAN attributes for
* QCA_NL80211_VENDOR_SUBCMD_PNO_PASSPOINT_NETWORK_FOUND sub-command.
*/
/* Unsigned 32-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_NETWORK_FOUND_NUM_MATCHES
= 36,
/* A nested array of
* QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_*
* attributes. Array size =
* *_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_NETWORK_FOUND_NUM_MATCHES.
*/
QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_RESULT_LIST = 37,
/* Unsigned 32-bit value; network block id for the matched network */
QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ID = 38,
/* Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the nested
* list of wifi scan results returned for each
* wifi_passpoint_match_result block.
*/
/* Unsigned 32-bit value */
QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ANQP_LEN = 39,
/* An array size of PASSPOINT_MATCH_ANQP_LEN of unsigned 8-bit values;
* ANQP data in the information_element format.
*/
QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ANQP = 40,
/* Unsigned 32-bit value; a GSCAN Capabilities attribute. */
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_HOTLIST_SSIDS = 41,
/* Unsigned 32-bit value; a GSCAN Capabilities attribute. */
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_EPNO_NETS = 42,
/* Unsigned 32-bit value; a GSCAN Capabilities attribute. */
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_EPNO_NETS_BY_SSID
= 43,
/* Unsigned 32-bit value; a GSCAN Capabilities attribute. */
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_WHITELISTED_SSID
= 44,
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_BUCKETS_SCANNED = 45,
/* Unsigned 32-bit value; a GSCAN Capabilities attribute.
* This is used to limit the maximum number of BSSIDs while sending
* the vendor command QCA_NL80211_VENDOR_SUBCMD_ROAM with attributes
* QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BLACKLIST_BSSID and
* QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_NUM_BSSID.
*/
QCA_WLAN_VENDOR_ATTR_GSCAN_MAX_NUM_BLACKLISTED_BSSID = 46,
/* keep last */
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_MAX =
QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_AFTER_LAST - 1,
};
enum qca_wlan_vendor_attr_pno_config_params {
QCA_WLAN_VENDOR_ATTR_PNO_INVALID = 0,
/* Attributes for data used by
* QCA_NL80211_VENDOR_SUBCMD_PNO_SET_PASSPOINT_LIST sub command.
*/
/* Unsigned 32-bit value */
QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM = 1,
/* Array of nested QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_*
* attributes. Array size =
* QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM.
*/
QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NETWORK_ARRAY = 2,
/* Unsigned 32-bit value */
QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ID = 3,
/* An array of 256 x unsigned 8-bit value; NULL terminated UTF-8 encoded
* realm, 0 if unspecified.
*/
QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_REALM = 4,
/* An array of 16 x unsigned 32-bit value; roaming consortium ids to
* match, 0 if unspecified.
*/
QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_CNSRTM_ID = 5,
/* An array of 6 x unsigned 8-bit value; MCC/MNC combination, 0s if
* unspecified.
*/
QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_PLMN = 6,
/* Attributes for data used by
* QCA_NL80211_VENDOR_SUBCMD_PNO_SET_LIST sub command.
*/
/* Unsigned 32-bit value */
QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS = 7,
/* Array of nested
* QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_*
* attributes. Array size =
* QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS.
*/
QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORKS_LIST = 8,
/* An array of 33 x unsigned 8-bit value; NULL terminated SSID */
QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_SSID = 9,
/* Signed 8-bit value; threshold for considering this SSID as found,
* required granularity for this threshold is 4 dBm to 8 dBm.
*/
QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_RSSI_THRESHOLD
= 10,
/* Unsigned 8-bit value; WIFI_PNO_FLAG_XXX */
QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_FLAGS = 11,
/* Unsigned 8-bit value; auth bit field for matching WPA IE */
QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_AUTH_BIT = 12,
/* Unsigned 8-bit to indicate ePNO type;
* It takes values from qca_wlan_epno_type
*/
QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_TYPE = 13,
/* Nested attribute to send the channel list */
QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_CHANNEL_LIST = 14,
/* Unsigned 32-bit value; indicates the interval between PNO scan
* cycles in msec.
*/
QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_SCAN_INTERVAL = 15,
QCA_WLAN_VENDOR_ATTR_EPNO_MIN5GHZ_RSSI = 16,
QCA_WLAN_VENDOR_ATTR_EPNO_MIN24GHZ_RSSI = 17,
QCA_WLAN_VENDOR_ATTR_EPNO_INITIAL_SCORE_MAX = 18,
QCA_WLAN_VENDOR_ATTR_EPNO_CURRENT_CONNECTION_BONUS = 19,
QCA_WLAN_VENDOR_ATTR_EPNO_SAME_NETWORK_BONUS = 20,
QCA_WLAN_VENDOR_ATTR_EPNO_SECURE_BONUS = 21,
QCA_WLAN_VENDOR_ATTR_EPNO_BAND5GHZ_BONUS = 22,
/* Unsigned 32-bit value, representing the PNO Request ID */
QCA_WLAN_VENDOR_ATTR_PNO_CONFIG_REQUEST_ID = 23,
/* keep last */
QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_PNO_MAX =
QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST - 1,
};
/**
* qca_wlan_vendor_acs_select_reason: This represents the different reasons why
* the ACS has to be triggered. These values are used by
* QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON and
* QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON
*/
enum qca_wlan_vendor_acs_select_reason {
/* Represents the reason that the ACS triggered during the AP start */
QCA_WLAN_VENDOR_ACS_SELECT_REASON_INIT,
/* Represents the reason that DFS found with the current channel */
QCA_WLAN_VENDOR_ACS_SELECT_REASON_DFS,
/* Represents the reason that LTE co-exist in the current band. */
QCA_WLAN_VENDOR_ACS_SELECT_REASON_LTE_COEX,
};
/**
* qca_wlan_vendor_attr_external_acs_policy: Attribute values for
* QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY to the vendor subcmd
* QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This represents the
* external ACS policies to select the channels w.r.t. the PCL weights.
* (QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL represents the channels and
* their PCL weights.)
* @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_MANDATORY: Mandatory to
* select a channel with non-zero PCL weight.
* @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_PREFERRED: Prefer a
* channel with non-zero PCL weight.
*
*/
enum qca_wlan_vendor_attr_external_acs_policy {
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_PREFERRED,
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_MANDATORY,
};
/**
* qca_wlan_vendor_channel_prop_flags: This represent the flags for a channel.
* This is used by QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS.
*/
enum qca_wlan_vendor_channel_prop_flags {
/* Bits 0, 1, 2, and 3 are reserved */
/* Turbo channel */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_TURBO = 1 << 4,
/* CCK channel */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_CCK = 1 << 5,
/* OFDM channel */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_OFDM = 1 << 6,
/* 2.4 GHz spectrum channel. */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_2GHZ = 1 << 7,
/* 5 GHz spectrum channel */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_5GHZ = 1 << 8,
/* Only passive scan allowed */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_PASSIVE = 1 << 9,
/* Dynamic CCK-OFDM channel */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_DYN = 1 << 10,
/* GFSK channel (FHSS PHY) */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_GFSK = 1 << 11,
/* Radar found on channel */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_RADAR = 1 << 12,
/* 11a static turbo channel only */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_STURBO = 1 << 13,
/* Half rate channel */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HALF = 1 << 14,
/* Quarter rate channel */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_QUARTER = 1 << 15,
/* HT 20 channel */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT20 = 1 << 16,
/* HT 40 with extension channel above */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40PLUS = 1 << 17,
/* HT 40 with extension channel below */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40MINUS = 1 << 18,
/* HT 40 intolerant */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40INTOL = 1 << 19,
/* VHT 20 channel */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT20 = 1 << 20,
/* VHT 40 with extension channel above */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT40PLUS = 1 << 21,
/* VHT 40 with extension channel below */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT40MINUS = 1 << 22,
/* VHT 80 channel */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT80 = 1 << 23,
/* HT 40 intolerant mark bit for ACS use */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40INTOLMARK = 1 << 24,
/* Channel temporarily blocked due to noise */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_BLOCKED = 1 << 25,
/* VHT 160 channel */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT160 = 1 << 26,
/* VHT 80+80 channel */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT80_80 = 1 << 27,
/* HE 20 channel */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE20 = 1 << 28,
/* HE 40 with extension channel above */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40PLUS = 1 << 29,
/* HE 40 with extension channel below */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40MINUS = 1 << 30,
/* HE 40 intolerant */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40INTOL = 1 << 31,
};
/**
* qca_wlan_vendor_channel_prop_flags_2: This represents the flags for a
* channel, and is a continuation of qca_wlan_vendor_channel_prop_flags. This is
* used by QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS_2.
*/
enum qca_wlan_vendor_channel_prop_flags_2 {
/* HE 40 intolerant mark bit for ACS use */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40INTOLMARK = 1 << 0,
/* HE 80 channel */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE80 = 1 << 1,
/* HE 160 channel */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE160 = 1 << 2,
/* HE 80+80 channel */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE80_80 = 1 << 3,
};
/**
* qca_wlan_vendor_channel_prop_flags_ext: This represent the extended flags for
* each channel. This is used by
* QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT.
*/
enum qca_wlan_vendor_channel_prop_flags_ext {
/* Radar found on channel */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_RADAR_FOUND = 1 << 0,
/* DFS required on channel */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS = 1 << 1,
/* DFS required on channel for 2nd band of 80+80 */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS_CFREQ2 = 1 << 2,
/* If channel has been checked for DFS */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS_CLEAR = 1 << 3,
/* Excluded in 802.11d */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_11D_EXCLUDED = 1 << 4,
/* Channel Switch Announcement received on this channel */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_CSA_RECEIVED = 1 << 5,
/* Ad-hoc is not allowed */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DISALLOW_ADHOC = 1 << 6,
/* Station only channel */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DISALLOW_HOSTAP = 1 << 7,
/* DFS radar history for slave device (STA mode) */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_HISTORY_RADAR = 1 << 8,
/* DFS CAC valid for slave device (STA mode) */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_CAC_VALID = 1 << 9,
};
/**
* qca_wlan_vendor_external_acs_event_chan_info_attr: Represents per channel
* information. These attributes are sent as part of
* QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO. Each set of the following
* attributes correspond to a single channel.
*/
enum qca_wlan_vendor_external_acs_event_chan_info_attr {
QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_INVALID = 0,
/* A bitmask (u32) with flags specified in
* enum qca_wlan_vendor_channel_prop_flags.
*/
QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS = 1,
/* A bitmask (u32) with flags specified in
* enum qca_wlan_vendor_channel_prop_flags_ext.
*/
QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT = 2,
/* frequency in MHz (u32) */
QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ = 3,
/* maximum regulatory transmission power (u32) */
QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_REG_POWER = 4,
/* maximum transmission power (u32) */
QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_POWER = 5,
/* minimum transmission power (u32) */
QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MIN_POWER = 6,
/* regulatory class id (u8) */
QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_REG_CLASS_ID = 7,
/* maximum antenna gain in (u8) */
QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_ANTENNA_GAIN = 8,
/* VHT segment 0 (u8) */
QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_0 = 9,
/* VHT segment 1 (u8) */
QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_1 = 10,
/* A bitmask (u32) with flags specified in
* enum qca_wlan_vendor_channel_prop_flags_2.
*/
QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS_2 = 11,
/* keep last */
QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_LAST,
QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX =
QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_LAST - 1,
};
/**
* qca_wlan_vendor_attr_pcl: Represents attributes for
* preferred channel list (PCL). These attributes are sent as part of
* QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL and
* QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST.
*/
enum qca_wlan_vendor_attr_pcl {
QCA_WLAN_VENDOR_ATTR_PCL_INVALID = 0,
/* Channel number (u8) */
QCA_WLAN_VENDOR_ATTR_PCL_CHANNEL = 1,
/* Channel weightage (u8) */
QCA_WLAN_VENDOR_ATTR_PCL_WEIGHT = 2,
/* Channel frequency (u32) in MHz */
QCA_WLAN_VENDOR_ATTR_PCL_FREQ = 3,
/* Channel flags (u32)
* bit 0 set: channel to be used for GO role,
* bit 1 set: channel to be used on CLI role,
* bit 2 set: channel must be considered for operating channel
* selection & peer chosen operating channel should be
* one of the channels with this flag set,
* bit 3 set: channel should be excluded in GO negotiation
*/
QCA_WLAN_VENDOR_ATTR_PCL_FLAG = 4,
};
/**
* qca_wlan_vendor_attr_external_acs_event: Attribute to vendor sub-command
* QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This attribute will be sent by
* host driver.
*/
enum qca_wlan_vendor_attr_external_acs_event {
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_INVALID = 0,
/* This reason (u8) refers to enum qca_wlan_vendor_acs_select_reason.
* This helps ACS module to understand why ACS needs to be started.
*/
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON = 1,
/* Flag attribute to indicate if driver supports spectral scanning */
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_SPECTRAL_SUPPORTED = 2,
/* Flag attribute to indicate if 11ac is offloaded to firmware */
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_OFFLOAD_ENABLED = 3,
/* Flag attribute to indicate if driver provides additional channel
* capability as part of scan operation
*/
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_ADD_CHAN_STATS_SUPPORT = 4,
/* Flag attribute to indicate interface status is UP */
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_AP_UP = 5,
/* Operating mode (u8) of interface. Takes one of enum nl80211_iftype
* values.
*/
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_SAP_MODE = 6,
/* Channel width (u8). It takes one of enum nl80211_chan_width values.
* This is the upper bound of channel width. ACS logic should try to get
* a channel with the specified width and if not found, look for lower
* values.
*/
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_WIDTH = 7,
/* This (u8) will hold values of one of enum nl80211_bands */
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_BAND = 8,
/* PHY/HW mode (u8). Takes one of enum qca_wlan_vendor_acs_hw_mode
* values
*/
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PHY_MODE = 9,
/* Array of (u32) supported frequency list among which ACS should choose
* best frequency.
*/
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_FREQ_LIST = 10,
/* Preferred channel list by the driver which will have array of nested
* values as per enum qca_wlan_vendor_attr_pcl attribute.
*/
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL = 11,
/* Array of nested attribute for each channel. It takes attr as defined
* in enum qca_wlan_vendor_external_acs_event_chan_info_attr.
*/
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO = 12,
/* External ACS policy such as PCL mandatory, PCL preferred, etc.
* It uses values defined in enum
* qca_wlan_vendor_attr_external_acs_policy.
*/
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY = 13,
/* Reference RF Operating Parameter (RROP) availability information
* (u16). It uses values defined in enum
* qca_wlan_vendor_attr_rropavail_info.
*/
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_RROPAVAIL_INFO = 14,
/* keep last */
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_LAST,
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_MAX =
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_LAST - 1,
};
/**
* qca_wlan_vendor_attr_external_acs_channels: Attributes to vendor subcmd
* QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This carries a list of channels
* in priority order as decided after ACS operation in userspace.
*/
enum qca_wlan_vendor_attr_external_acs_channels {
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_INVALID = 0,
/* One of reason code (u8) from enum qca_wlan_vendor_acs_select_reason
*/
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON = 1,
/* Array of nested values for each channel with following attributes:
* QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_BAND,
* QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY,
* QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY,
* QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0,
* QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1,
* QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH
*/
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LIST = 2,
/* This (u8) will hold values of one of enum nl80211_bands */
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_BAND = 3,
/* Primary channel (u8) */
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY = 4,
/* Secondary channel (u8) used for HT 40 MHz channels */
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY = 5,
/* VHT seg0 channel (u8) */
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0 = 6,
/* VHT seg1 channel (u8) */
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1 = 7,
/* Channel width (u8). Takes one of enum nl80211_chan_width values. */
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH = 8,
/* keep last */
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LAST,
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_MAX =
QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LAST - 1
};
enum qca_chip_power_save_failure_reason {
/* Indicates if the reason for the failure is due to a protocol
* layer/module.
*/
QCA_CHIP_POWER_SAVE_FAILURE_REASON_PROTOCOL = 0,
/* Indicates if the reason for the failure is due to a hardware issue.
*/
QCA_CHIP_POWER_SAVE_FAILURE_REASON_HARDWARE = 1,
};
/**
* qca_attr_chip_power_save_failure: Attributes to vendor subcmd
* QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE. This carries the requisite
* information leading to the power save failure.
*/
enum qca_attr_chip_power_save_failure {
QCA_ATTR_CHIP_POWER_SAVE_FAILURE_INVALID = 0,
/* Reason to cause the power save failure.
* These reasons are represented by
* enum qca_chip_power_save_failure_reason.
*/
QCA_ATTR_CHIP_POWER_SAVE_FAILURE_REASON = 1,
/* keep last */
QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST,
QCA_ATTR_CHIP_POWER_SAVE_FAILURE_MAX =
QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST - 1,
};
/**
* qca_wlan_vendor_nud_stats_data_pkt_flags: Flag representing the various
* data types for which the stats have to get collected.
*/
enum qca_wlan_vendor_nud_stats_data_pkt_flags {
QCA_WLAN_VENDOR_NUD_STATS_DATA_ARP = 1 << 0,
QCA_WLAN_VENDOR_NUD_STATS_DATA_DNS = 1 << 1,
QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_HANDSHAKE = 1 << 2,
QCA_WLAN_VENDOR_NUD_STATS_DATA_ICMPV4 = 1 << 3,
QCA_WLAN_VENDOR_NUD_STATS_DATA_ICMPV6 = 1 << 4,
/* Used by QCA_ATTR_NUD_STATS_PKT_TYPE only in nud stats get
* to represent the stats of respective data type.
*/
QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_SYN = 1 << 5,
QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_SYN_ACK = 1 << 6,
QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_ACK = 1 << 7,
};
enum qca_wlan_vendor_nud_stats_set_data_pkt_info {
QCA_ATTR_NUD_STATS_DATA_PKT_INFO_INVALID = 0,
/* Represents the data packet type to be monitored (u32).
* Host driver tracks the stats corresponding to each data frame
* represented by these flags.
* These data packets are represented by
* enum qca_wlan_vendor_nud_stats_data_pkt_flags
*/
QCA_ATTR_NUD_STATS_DATA_PKT_INFO_TYPE = 1,
/* Name corresponding to the DNS frame for which the respective DNS
* stats have to get monitored (string). Max string length 255.
*/
QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DNS_DOMAIN_NAME = 2,
/* source port on which the respective proto stats have to get
* collected (u32).
*/
QCA_ATTR_NUD_STATS_DATA_PKT_INFO_SRC_PORT = 3,
/* destination port on which the respective proto stats have to get
* collected (u32).
*/
QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DEST_PORT = 4,
/* IPv4 address for which the destined data packets have to be
* monitored. (in network byte order), u32.
*/
QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DEST_IPV4 = 5,
/* IPv6 address for which the destined data packets have to be
* monitored. (in network byte order), 16 bytes array.
*/
QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DEST_IPV6 = 6,
QCA_ATTR_NUD_STATS_DATA_PKT_INFO_LAST,
QCA_ATTR_NUD_STATS_DATA_PKT_INFO_MAX =
QCA_ATTR_NUD_STATS_DATA_PKT_INFO_LAST - 1,
};
/**
* qca_wlan_vendor_attr_nud_stats_set: Attributes to vendor subcmd
* QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET. This carries the requisite
* information to start/stop the NUD statistics collection.
*/
enum qca_attr_nud_stats_set {
QCA_ATTR_NUD_STATS_SET_INVALID = 0,
/* Flag to start/stop the NUD statistics collection.
* Start - If included, Stop - If not included
*/
QCA_ATTR_NUD_STATS_SET_START = 1,
/* IPv4 address of the default gateway (in network byte order), u32 */
QCA_ATTR_NUD_STATS_GW_IPV4 = 2,
/* Represents the list of data packet types to be monitored.
* Host driver tracks the stats corresponding to each data frame
* represented by these flags.
* These data packets are represented by
* enum qca_wlan_vendor_nud_stats_set_data_pkt_info
*/
QCA_ATTR_NUD_STATS_SET_DATA_PKT_INFO = 3,
/* keep last */
QCA_ATTR_NUD_STATS_SET_LAST,
QCA_ATTR_NUD_STATS_SET_MAX =
QCA_ATTR_NUD_STATS_SET_LAST - 1,
};
enum qca_attr_nud_data_stats {
QCA_ATTR_NUD_DATA_STATS_INVALID = 0,
/* Data packet type for which the stats are collected (u32).
* Represented by enum qca_wlan_vendor_nud_stats_data_pkt_flags
*/
QCA_ATTR_NUD_STATS_PKT_TYPE = 1,
/* Name corresponding to the DNS frame for which the respective DNS
* stats are monitored (string). Max string length 255.
*/
QCA_ATTR_NUD_STATS_PKT_DNS_DOMAIN_NAME = 2,
/* source port on which the respective proto stats are collected (u32).
*/
QCA_ATTR_NUD_STATS_PKT_SRC_PORT = 3,
/* destination port on which the respective proto stats are collected
* (u32).
*/
QCA_ATTR_NUD_STATS_PKT_DEST_PORT = 4,
/* IPv4 address for which the destined data packets have to be
* monitored. (in network byte order), u32.
*/
QCA_ATTR_NUD_STATS_PKT_DEST_IPV4 = 5,
/* IPv6 address for which the destined data packets have to be
* monitored. (in network byte order), 16 bytes array.
*/
QCA_ATTR_NUD_STATS_PKT_DEST_IPV6 = 6,
/* Data packet Request count received from netdev (u32). */
QCA_ATTR_NUD_STATS_PKT_REQ_COUNT_FROM_NETDEV = 7,
/* Data packet Request count sent to lower MAC from upper MAC (u32). */
QCA_ATTR_NUD_STATS_PKT_REQ_COUNT_TO_LOWER_MAC = 8,
/* Data packet Request count received by lower MAC from upper MAC
* (u32)
*/
QCA_ATTR_NUD_STATS_PKT_REQ_RX_COUNT_BY_LOWER_MAC = 9,
/* Data packet Request count successfully transmitted by the device
* (u32)
*/
QCA_ATTR_NUD_STATS_PKT_REQ_COUNT_TX_SUCCESS = 10,
/* Data packet Response count received by lower MAC (u32) */
QCA_ATTR_NUD_STATS_PKT_RSP_RX_COUNT_BY_LOWER_MAC = 11,
/* Data packet Response count received by upper MAC (u32) */
QCA_ATTR_NUD_STATS_PKT_RSP_RX_COUNT_BY_UPPER_MAC = 12,
/* Data packet Response count delivered to netdev (u32) */
QCA_ATTR_NUD_STATS_PKT_RSP_COUNT_TO_NETDEV = 13,
/* Data Packet Response count that are dropped out of order (u32) */
QCA_ATTR_NUD_STATS_PKT_RSP_COUNT_OUT_OF_ORDER_DROP = 14,
/* keep last */
QCA_ATTR_NUD_DATA_STATS_LAST,
QCA_ATTR_NUD_DATA_STATS_MAX =
QCA_ATTR_NUD_DATA_STATS_LAST - 1,
};
/**
* qca_attr_nud_stats_get: Attributes to vendor subcmd
* QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET. This carries the requisite
* NUD statistics collected when queried.
*/
enum qca_attr_nud_stats_get {
QCA_ATTR_NUD_STATS_GET_INVALID = 0,
/* ARP Request count from netdev (u32) */
QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_FROM_NETDEV = 1,
/* ARP Request count sent to lower MAC from upper MAC (u32) */
QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_TO_LOWER_MAC = 2,
/* ARP Request count received by lower MAC from upper MAC (u32) */
QCA_ATTR_NUD_STATS_ARP_REQ_RX_COUNT_BY_LOWER_MAC = 3,
/* ARP Request count successfully transmitted by the device (u32) */
QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_TX_SUCCESS = 4,
/* ARP Response count received by lower MAC (u32) */
QCA_ATTR_NUD_STATS_ARP_RSP_RX_COUNT_BY_LOWER_MAC = 5,
/* ARP Response count received by upper MAC (u32) */
QCA_ATTR_NUD_STATS_ARP_RSP_RX_COUNT_BY_UPPER_MAC = 6,
/* ARP Response count delivered to netdev (u32) */
QCA_ATTR_NUD_STATS_ARP_RSP_COUNT_TO_NETDEV = 7,
/* ARP Response count dropped due to out of order reception (u32) */
QCA_ATTR_NUD_STATS_ARP_RSP_COUNT_OUT_OF_ORDER_DROP = 8,
/* Flag indicating if the station's link to the AP is active.
* Active Link - If included, Inactive link - If not included
*/
QCA_ATTR_NUD_STATS_AP_LINK_ACTIVE = 9,
/* Flag indicating if there is any duplicate address detected (DAD).
* Yes - If detected, No - If not detected.
*/
QCA_ATTR_NUD_STATS_IS_DAD = 10,
/* List of Data packet types for which the stats are requested.
* This list does not carry ARP stats as they are done by the
* above attributes. Represented by enum qca_attr_nud_data_stats.
*/
QCA_ATTR_NUD_STATS_DATA_PKT_STATS = 11,
/* keep last */
QCA_ATTR_NUD_STATS_GET_LAST,
QCA_ATTR_NUD_STATS_GET_MAX =
QCA_ATTR_NUD_STATS_GET_LAST - 1,
};
enum qca_wlan_btm_candidate_status {
QCA_STATUS_ACCEPT = 0,
QCA_STATUS_REJECT_EXCESSIVE_FRAME_LOSS_EXPECTED = 1,
QCA_STATUS_REJECT_EXCESSIVE_DELAY_EXPECTED = 2,
QCA_STATUS_REJECT_INSUFFICIENT_QOS_CAPACITY = 3,
QCA_STATUS_REJECT_LOW_RSSI = 4,
QCA_STATUS_REJECT_HIGH_INTERFERENCE = 5,
QCA_STATUS_REJECT_UNKNOWN = 6,
};
enum qca_wlan_vendor_attr_btm_candidate_info {
QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_INVALID = 0,
/* 6-byte MAC address representing the BSSID of transition candidate */
QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID = 1,
/* Unsigned 32-bit value from enum qca_wlan_btm_candidate_status
* returned by the driver. It says whether the BSSID provided in
* QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID is acceptable by
* the driver, if not it specifies the reason for rejection.
* Note that the user-space can overwrite the transition reject reason
* codes provided by driver based on more information.
*/
QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_STATUS = 2,
/* keep last */
QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_MAX =
QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_AFTER_LAST - 1,
};
enum qca_attr_trace_level {
QCA_ATTR_TRACE_LEVEL_INVALID = 0,
/*
* Nested array of the following attributes:
* QCA_ATTR_TRACE_LEVEL_MODULE,
* QCA_ATTR_TRACE_LEVEL_MASK.
*/
QCA_ATTR_TRACE_LEVEL_PARAM = 1,
/*
* Specific QCA host driver module. Please refer to the QCA host
* driver implementation to get the specific module ID.
*/
QCA_ATTR_TRACE_LEVEL_MODULE = 2,
/* Different trace level masks represented in the QCA host driver. */
QCA_ATTR_TRACE_LEVEL_MASK = 3,
/* keep last */
QCA_ATTR_TRACE_LEVEL_AFTER_LAST,
QCA_ATTR_TRACE_LEVEL_MAX =
QCA_ATTR_TRACE_LEVEL_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_get_he_capabilities - IEEE 802.11ax HE capabilities
*/
enum qca_wlan_vendor_attr_get_he_capabilities {
QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_INVALID = 0,
/* Whether HE capabilities is supported
* (u8 attribute: 0 = not supported, 1 = supported)
*/
QCA_WLAN_VENDOR_ATTR_HE_SUPPORTED = 1,
/* HE PHY capabilities, array of 3 u32 values */
QCA_WLAN_VENDOR_ATTR_PHY_CAPAB = 2,
/* HE MAC capabilities (u32 attribute) */
QCA_WLAN_VENDOR_ATTR_MAC_CAPAB = 3,
/* HE MCS map (u32 attribute) */
QCA_WLAN_VENDOR_ATTR_HE_MCS = 4,
/* Number of SS (u32 attribute) */
QCA_WLAN_VENDOR_ATTR_NUM_SS = 5,
/* RU count (u32 attribute) */
QCA_WLAN_VENDOR_ATTR_RU_IDX_MASK = 6,
/* PPE threshold data, array of 8 u32 values */
QCA_WLAN_VENDOR_ATTR_PPE_THRESHOLD = 7,
/* keep last */
QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_MAX =
QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_spectral_scan - Spectral scan config parameters
*/
enum qca_wlan_vendor_attr_spectral_scan {
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_INVALID = 0,
/* Number of times the chip enters spectral scan mode before
* deactivating spectral scans. When set to 0, chip will enter spectral
* scan mode continuously. u32 attribute.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SCAN_COUNT = 1,
/* Spectral scan period. Period increment resolution is 256*Tclk,
* where Tclk = 1/44 MHz (Gmode), 1/40 MHz (Amode). u32 attribute.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SCAN_PERIOD = 2,
/* Spectral scan priority. u32 attribute. */
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_PRIORITY = 3,
/* Number of FFT data points to compute. u32 attribute. */
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FFT_SIZE = 4,
/* Enable targeted gain change before starting the spectral scan FFT.
* u32 attribute.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_GC_ENA = 5,
/* Restart a queued spectral scan. u32 attribute. */
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RESTART_ENA = 6,
/* Noise floor reference number for the calculation of bin power.
* u32 attribute.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_NOISE_FLOOR_REF = 7,
/* Disallow spectral scan triggers after TX/RX packets by setting
* this delay value to roughly SIFS time period or greater.
* u32 attribute.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_INIT_DELAY = 8,
/* Number of strong bins (inclusive) per sub-channel, below
* which a signal is declared a narrow band tone. u32 attribute.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_NB_TONE_THR = 9,
/* Specify the threshold over which a bin is declared strong (for
* scan bandwidth analysis). u32 attribute.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_STR_BIN_THR = 10,
/* Spectral scan report mode. u32 attribute. */
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_WB_RPT_MODE = 11,
/* RSSI report mode, if the ADC RSSI is below
* QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_THR,
* then FFTs will not trigger, but timestamps and summaries get
* reported. u32 attribute.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_RPT_MODE = 12,
/* ADC RSSI must be greater than or equal to this threshold (signed dB)
* to ensure spectral scan reporting with normal error code.
* u32 attribute.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_THR = 13,
/* Format of frequency bin magnitude for spectral scan triggered FFTs:
* 0: linear magnitude, 1: log magnitude (20*log10(lin_mag)).
* u32 attribute.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_PWR_FORMAT = 14,
/* Format of FFT report to software for spectral scan triggered FFTs.
* 0: No FFT report (only spectral scan summary report)
* 1: 2-dword summary of metrics for each completed FFT + spectral scan
* report
* 2: 2-dword summary of metrics for each completed FFT + 1x-oversampled
* bins (in-band) per FFT + spectral scan summary report
* 3: 2-dword summary of metrics for each completed FFT + 2x-oversampled
* bins (all) per FFT + spectral scan summary report
* u32 attribute.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RPT_MODE = 15,
/* Number of LSBs to shift out in order to scale the FFT bins.
* u32 attribute.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_BIN_SCALE = 16,
/* Set to 1 (with spectral_scan_pwr_format=1), to report bin magnitudes
* in dBm power. u32 attribute.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DBM_ADJ = 17,
/* Per chain enable mask to select input ADC for search FFT.
* u32 attribute.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_CHN_MASK = 18,
/* An unsigned 64-bit integer provided by host driver to identify the
* spectral scan request. This attribute is included in the scan
* response message for @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START
* and used as an attribute in
* @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP to identify the
* specific scan to be stopped.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE = 19,
/* Skip interval for FFT reports. u32 attribute */
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FFT_PERIOD = 20,
/* Set to report only one set of FFT results.
* u32 attribute.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SHORT_REPORT = 21,
/* Debug level for spectral module in driver.
* 0 : Verbosity level 0
* 1 : Verbosity level 1
* 2 : Verbosity level 2
* 3 : Matched filterID display
* 4 : One time dump of FFT report
* u32 attribute.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DEBUG_LEVEL = 22,
/* Type of spectral scan request. u32 attribute.
* It uses values defined in enum
* qca_wlan_vendor_attr_spectral_scan_request_type.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE = 23,
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_MAX =
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_spectral_diag_stats - Used by the vendor command
* QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS.
*/
enum qca_wlan_vendor_attr_spectral_diag_stats {
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_INVALID = 0,
/* Number of spectral TLV signature mismatches.
* u64 attribute.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_SIG_MISMATCH = 1,
/* Number of spectral phyerror events with insufficient length when
* parsing for secondary 80 search FFT report. u64 attribute.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_SEC80_SFFT_INSUFFLEN = 2,
/* Number of spectral phyerror events without secondary 80
* search FFT report. u64 attribute.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_NOSEC80_SFFT = 3,
/* Number of spectral phyerror events with vht operation segment 1 id
* mismatches in search fft report. u64 attribute.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_VHTSEG1ID_MISMATCH = 4,
/* Number of spectral phyerror events with vht operation segment 2 id
* mismatches in search fft report. u64 attribute.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_VHTSEG2ID_MISMATCH = 5,
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_MAX =
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_spectral_cap - Used by the vendor command
* QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO.
*/
enum qca_wlan_vendor_attr_spectral_cap {
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_INVALID = 0,
/* Flag attribute to indicate phydiag capability */
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_PHYDIAG = 1,
/* Flag attribute to indicate radar detection capability */
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_RADAR = 2,
/* Flag attribute to indicate spectral capability */
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_SPECTRAL = 3,
/* Flag attribute to indicate advanced spectral capability */
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_ADVANCED_SPECTRAL = 4,
/* Spectral hardware generation. u32 attribute.
* It uses values defined in enum
* qca_wlan_vendor_spectral_scan_cap_hw_gen.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HW_GEN = 5,
/* Spectral bin scaling formula ID. u16 attribute.
* It uses values defined in enum
* qca_wlan_vendor_spectral_scan_cap_formula_id.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_FORMULA_ID = 6,
/* Spectral bin scaling param - low level offset.
* s16 attribute.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_LOW_LEVEL_OFFSET = 7,
/* Spectral bin scaling param - high level offset.
* s16 attribute.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HIGH_LEVEL_OFFSET = 8,
/* Spectral bin scaling param - RSSI threshold.
* s16 attribute.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_RSSI_THR = 9,
/* Spectral bin scaling param - default AGC max gain.
* u8 attribute.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_DEFAULT_AGC_MAX_GAIN = 10,
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_MAX =
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_spectral_scan_status - used by the vendor command
* QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS.
*/
enum qca_wlan_vendor_attr_spectral_scan_status {
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_INVALID = 0,
/* Flag attribute to indicate whether spectral scan is enabled */
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_IS_ENABLED = 1,
/* Flag attribute to indicate whether spectral scan is in progress*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_IS_ACTIVE = 2,
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_MAX =
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_AFTER_LAST - 1,
};
/**
* qca_wlan_vendor_attr_spectral_scan_request_type: Attribute values for
* QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE to the vendor subcmd
* QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START. This represents the
* spectral scan request types.
* @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN_AND_CONFIG: Request to
* set the spectral parameters and start scan.
* @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN: Request to
* only set the spectral parameters.
* @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_CONFIG: Request to
* only start the spectral scan.
*/
enum qca_wlan_vendor_attr_spectral_scan_request_type {
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN_AND_CONFIG,
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN,
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_CONFIG,
};
/**
* qca_wlan_vendor_spectral_scan_cap_hw_gen: Attribute values for
* QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HW_GEN to the vendor subcmd
* QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO. This represents the
* spectral hardware generation.
* @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_1: generation 1
* @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_2: generation 2
* @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_3: generation 3
*/
enum qca_wlan_vendor_spectral_scan_cap_hw_gen {
QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_1 = 0,
QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_2 = 1,
QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_3 = 2,
};
enum qca_wlan_vendor_tos {
QCA_WLAN_VENDOR_TOS_BK = 0,
QCA_WLAN_VENDOR_TOS_BE = 1,
QCA_WLAN_VENDOR_TOS_VI = 2,
QCA_WLAN_VENDOR_TOS_VO = 3,
};
/**
* enum qca_wlan_vendor_attr_active_tos - Used by the vendor command
* QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS.
*/
enum qca_wlan_vendor_attr_active_tos {
QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS_INVALID = 0,
/* Type Of Service - Represented by qca_wlan_vendor_tos */
QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS = 1,
/* Flag attribute representing the start (attribute included) or stop
* (attribute not included) of the respective TOS.
*/
QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS_START = 2,
};
enum qca_wlan_vendor_hang_reason {
/* Unspecified reason */
QCA_WLAN_HANG_REASON_UNSPECIFIED = 0,
/* No Map for the MAC entry for the received frame */
QCA_WLAN_HANG_RX_HASH_NO_ENTRY_FOUND = 1,
/* Peer deletion timeout happened */
QCA_WLAN_HANG_PEER_DELETION_TIMEDOUT = 2,
/* Peer unmap timeout */
QCA_WLAN_HANG_PEER_UNMAP_TIMEDOUT = 3,
/* Scan request timed out */
QCA_WLAN_HANG_SCAN_REQ_EXPIRED = 4,
/* Consecutive Scan attempt failures */
QCA_WLAN_HANG_SCAN_ATTEMPT_FAILURES = 5,
/* Unable to get the message buffer */
QCA_WLAN_HANG_GET_MSG_BUFF_FAILURE = 6,
/* Current command processing is timedout */
QCA_WLAN_HANG_ACTIVE_LIST_TIMEOUT = 7,
/* Timeout for an ACK from FW for suspend request */
QCA_WLAN_HANG_SUSPEND_TIMEOUT = 8,
/* Timeout for an ACK from FW for resume request */
QCA_WLAN_HANG_RESUME_TIMEOUT = 9,
/* Transmission timeout for consecutive data frames */
QCA_WLAN_HANG_TRANSMISSIONS_TIMEOUT = 10,
/* Timeout for the TX completion status of data frame */
QCA_WLAN_HANG_TX_COMPLETE_TIMEOUT = 11,
/* DXE failure for TX/RX, DXE resource unavailability */
QCA_WLAN_HANG_DXE_FAILURE = 12,
/* WMI pending commands exceed the maximum count */
QCA_WLAN_HANG_WMI_EXCEED_MAX_PENDING_CMDS = 13,
};
/**
* enum qca_wlan_vendor_attr_hang - Used by the vendor command
* QCA_NL80211_VENDOR_SUBCMD_HANG.
*/
enum qca_wlan_vendor_attr_hang {
QCA_WLAN_VENDOR_ATTR_HANG_INVALID = 0,
/* Reason for the hang - u32 attribute with a value from enum
* qca_wlan_vendor_hang_reason.
*/
QCA_WLAN_VENDOR_ATTR_HANG_REASON = 1,
QCA_WLAN_VENDOR_ATTR_HANG_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_HANG_MAX =
QCA_WLAN_VENDOR_ATTR_HANG_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_flush_pending - Attributes for
* flushing pending traffic in firmware.
*
* @QCA_WLAN_VENDOR_ATTR_PEER_ADDR: Configure peer MAC address.
* @QCA_WLAN_VENDOR_ATTR_AC: Configure access category of the pending
* packets. It is u8 value with bit 0~3 represent AC_BE, AC_BK,
* AC_VI, AC_VO respectively. Set the corresponding bit to 1 to
* flush packets with access category.
*/
enum qca_wlan_vendor_attr_flush_pending {
QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_PEER_ADDR = 1,
QCA_WLAN_VENDOR_ATTR_AC = 2,
/* keep last */
QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_MAX =
QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_AFTER_LAST - 1,
};
/**
* qca_wlan_vendor_spectral_scan_cap_formula_id: Attribute values for
* QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_FORMULA_ID in the vendor subcmd
* QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO. This represents the
* Spectral bin scaling formula ID.
* @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_NO_SCALING: No scaling
* @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_AGC_GAIN_RSSI_CORR_BASED: AGC gain
* and RSSI threshold based formula.
*/
enum qca_wlan_vendor_spectral_scan_cap_formula_id {
QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_NO_SCALING = 0,
QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_AGC_GAIN_RSSI_CORR_BASED = 1,
};
/**
* enum qca_wlan_vendor_attr_rropavail_info - Specifies whether Representative
* RF Operating Parameter (RROP) information is available, and if so, at which
* point in the application-driver interaction sequence it can be retrieved by
* the application from the driver. This point may vary by architecture and
* other factors. This is a u16 value.
*/
enum qca_wlan_vendor_attr_rropavail_info {
/* RROP information is unavailable. */
QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_UNAVAILABLE,
/* RROP information is available and the application can retrieve the
* information after receiving an QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS
* event from the driver.
*/
QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_EXTERNAL_ACS_START,
/* RROP information is available only after a vendor specific scan
* (requested using QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN) has
* successfully completed. The application can retrieve the information
* after receiving the QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE event from
* the driver.
*/
QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_VSCAN_END,
};
/**
* enum qca_wlan_vendor_attr_rrop_info - Specifies vendor specific
* Representative RF Operating Parameter (RROP) information. It is sent for the
* vendor command QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO. This information is
* intended for use by external Auto Channel Selection applications. It provides
* guidance values for some RF parameters that are used by the system during
* operation. These values could vary by channel, band, radio, and so on.
*/
enum qca_wlan_vendor_attr_rrop_info {
QCA_WLAN_VENDOR_ATTR_RROP_INFO_INVALID = 0,
/* Representative Tx Power List (RTPL) which has an array of nested
* values as per attributes in enum qca_wlan_vendor_attr_rtplinst.
*/
QCA_WLAN_VENDOR_ATTR_RROP_INFO_RTPL = 1,
QCA_WLAN_VENDOR_ATTR_RROP_INFO_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_RROP_INFO_MAX =
QCA_WLAN_VENDOR_ATTR_RROP_INFO_AFTER_LAST - 1
};
/**
* enum qca_wlan_vendor_attr_rtplinst - Specifies attributes for individual list
* entry instances in the Representative Tx Power List (RTPL). It provides
* simplified power values intended for helping external Auto channel Selection
* applications compare potential Tx power performance between channels, other
* operating conditions remaining identical. These values are not necessarily
* the actual Tx power values that will be used by the system. They are also not
* necessarily the max or average values that will be used. Instead, they are
* relative, summarized keys for algorithmic use computed by the driver or
* underlying firmware considering a number of vendor specific factors.
*/
enum qca_wlan_vendor_attr_rtplinst {
QCA_WLAN_VENDOR_ATTR_RTPLINST_INVALID = 0,
/* Primary channel number (u8) */
QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY = 1,
/* Representative Tx power in dBm (s32) with emphasis on throughput. */
QCA_WLAN_VENDOR_ATTR_RTPLINST_TXPOWER_THROUGHPUT = 2,
/* Representative Tx power in dBm (s32) with emphasis on range. */
QCA_WLAN_VENDOR_ATTR_RTPLINST_TXPOWER_RANGE = 3,
QCA_WLAN_VENDOR_ATTR_RTPLINST_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_RTPLINST_MAX =
QCA_WLAN_VENDOR_ATTR_RTPLINST_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_config_latency_level - Level for
* wlan latency module.
*
* There will be various of Wi-Fi functionality like scan/roaming/adaptive
* power saving which would causing data exchange out of service, this
* would be a big impact on latency. For latency sensitive applications over
* Wi-Fi are intolerant to such operations and thus would configure them
* to meet their respective needs. It is well understood by such applications
* that altering the default behavior would degrade the Wi-Fi functionality
* w.r.t the above pointed WLAN operations.
*
* @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_NORMAL:
* Default WLAN operation level which throughput orientated.
* @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MODERATE:
* Use moderate level to improve latency by limit scan duration.
* @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_LOW:
* Use low latency level to benifit application like concurrent
* downloading or video streaming via constraint scan/adaptive PS.
* @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_ULTRALOW:
* Use ultra low latency level to benefit for gaming/voice
* application via constraint scan/roaming/adaptive PS.
*/
enum qca_wlan_vendor_attr_config_latency_level {
QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_NORMAL = 1,
QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MODERATE = 2,
QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_LOW = 3,
QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_ULTRALOW = 4,
/* keep last */
QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MAX =
QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_wlan_mac - Used by the vendor command
* QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO.
*/
enum qca_wlan_vendor_attr_mac {
QCA_WLAN_VENDOR_ATTR_MAC_INVALID = 0,
/* MAC mode info list which has an array of nested values as
* per attributes in enum qca_wlan_vendor_attr_mac_mode_info.
*/
QCA_WLAN_VENDOR_ATTR_MAC_INFO = 1,
/* keep last */
QCA_WLAN_VENDOR_ATTR_MAC_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_MAC_MAX =
QCA_WLAN_VENDOR_ATTR_MAC_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_mac_iface_info - Information of the connected
* Wi-Fi netdev interface on a respective MAC.
* Used by the attribute QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO.
*/
enum qca_wlan_vendor_attr_mac_iface_info {
QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_INVALID = 0,
/* Wi-Fi netdev's interface index (u32) */
QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_IFINDEX = 1,
/* Associated frequency in MHz of the connected Wi-Fi interface (u32) */
QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_FREQ = 2,
/* keep last */
QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_MAX =
QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_mac_info - Points to MAC the information.
* Used by the attribute QCA_WLAN_VENDOR_ATTR_MAC_INFO of the
* vendor command QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO.
*/
enum qca_wlan_vendor_attr_mac_info {
QCA_WLAN_VENDOR_ATTR_MAC_INFO_INVALID = 0,
/* Hardware MAC ID associated for the MAC (u32) */
QCA_WLAN_VENDOR_ATTR_MAC_INFO_MAC_ID = 1,
/* Band supported by the MAC at a given point.
* This is a u32 bitmask of BIT(NL80211_BAND_*) as described in %enum
* nl80211_band.
*/
QCA_WLAN_VENDOR_ATTR_MAC_INFO_BAND = 2,
/* Refers to list of WLAN netdev interfaces associated with this MAC.
* Represented by enum qca_wlan_vendor_attr_mac_iface_info.
*/
QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO = 3,
/* keep last */
QCA_WLAN_VENDOR_ATTR_MAC_INFO_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_MAC_INFO_MAX =
QCA_WLAN_VENDOR_ATTR_MAC_INFO_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_get_logger_features - Used by the vendor command
* QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET.
*/
enum qca_wlan_vendor_attr_get_logger_features {
QCA_WLAN_VENDOR_ATTR_LOGGER_INVALID = 0,
/* Unsigned 32-bit enum value of wifi_logger_supported_features */
QCA_WLAN_VENDOR_ATTR_LOGGER_SUPPORTED = 1,
/* keep last */
QCA_WLAN_VENDOR_ATTR_LOGGER_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_LOGGER_MAX =
QCA_WLAN_VENDOR_ATTR_LOGGER_AFTER_LAST - 1,
};
/**
* enum wifi_logger_supported_features - Values for supported logger features
*/
enum wifi_logger_supported_features {
WIFI_LOGGER_MEMORY_DUMP_FEATURE = (1 << (0)),
WIFI_LOGGER_PER_PACKET_TX_RX_STATUS_FEATURE = (1 << (1)),
WIFI_LOGGER_CONNECT_EVENT_FEATURE = (1 << (2)),
WIFI_LOGGER_POWER_EVENT_FEATURE = (1 << (3)),
WIFI_LOGGER_WAKE_LOCK_FEATURE = (1 << (4)),
WIFI_LOGGER_VERBOSE_FEATURE = (1 << (5)),
WIFI_LOGGER_WATCHDOG_TIMER_FEATURE = (1 << (6)),
WIFI_LOGGER_DRIVER_DUMP_FEATURE = (1 << (7)),
WIFI_LOGGER_PACKET_FATE_FEATURE = (1 << (8)),
};
/**
* enum qca_wlan_tdls_caps_features_supported - Values for TDLS get
* capabilities features
*/
enum qca_wlan_tdls_caps_features_supported {
WIFI_TDLS_SUPPORT = (1 << (0)),
WIFI_TDLS_EXTERNAL_CONTROL_SUPPORT = (1 << (1)),
WIFI_TDLS_OFFCHANNEL_SUPPORT = (1 << (2))
};
/**
* enum qca_wlan_vendor_attr_tdls_get_capabilities - Used by the vendor command
* QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_CAPABILITIES.
*/
enum qca_wlan_vendor_attr_tdls_get_capabilities {
QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_INVALID = 0,
/* Indicates the max concurrent sessions */
/* Unsigned 32-bit value */
QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_MAX_CONC_SESSIONS,
/* Indicates the support for features */
/* Unsigned 32-bit bitmap qca_wlan_tdls_caps_features_supported
*/
QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_FEATURES_SUPPORTED,
/* keep last */
QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_MAX =
QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_AFTER_LAST - 1,
};
/**
* enum qca_wlan_offloaded_packets_sending_control - Offload packets control
* command used as value for the attribute
* QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SENDING_CONTROL.
*/
enum qca_wlan_offloaded_packets_sending_control {
QCA_WLAN_OFFLOADED_PACKETS_SENDING_CONTROL_INVALID = 0,
QCA_WLAN_OFFLOADED_PACKETS_SENDING_START,
QCA_WLAN_OFFLOADED_PACKETS_SENDING_STOP
};
/**
* enum qca_wlan_vendor_attr_offloaded_packets - Used by the vendor command
* QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS.
*/
enum qca_wlan_vendor_attr_offloaded_packets {
QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_INVALID = 0,
/* Takes valid value from the enum
* qca_wlan_offloaded_packets_sending_control
* Unsigned 32-bit value
*/
QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SENDING_CONTROL,
/* Unsigned 32-bit value */
QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_REQUEST_ID,
/* array of u8 len: Max packet size */
QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_IP_PACKET_DATA,
/* 6-byte MAC address used to represent source MAC address */
QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SRC_MAC_ADDR,
/* 6-byte MAC address used to represent destination MAC address */
QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_DST_MAC_ADDR,
/* Unsigned 32-bit value, in milli seconds */
QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_PERIOD,
/* This optional unsigned 16-bit attribute is used for specifying
* ethernet protocol type. If not specified ethertype defaults to IPv4.
*/
QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_ETHER_PROTO_TYPE,
/* keep last */
QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_MAX =
QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_AFTER_LAST - 1,
};
/**
* enum qca_wlan_rssi_monitoring_control - RSSI control commands used as values
* by the attribute QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CONTROL.
*/
enum qca_wlan_rssi_monitoring_control {
QCA_WLAN_RSSI_MONITORING_CONTROL_INVALID = 0,
QCA_WLAN_RSSI_MONITORING_START,
QCA_WLAN_RSSI_MONITORING_STOP,
};
/**
* enum qca_wlan_vendor_attr_rssi_monitoring - Used by the vendor command
* QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI.
*/
enum qca_wlan_vendor_attr_rssi_monitoring {
QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_INVALID = 0,
/* Takes valid value from the enum
* qca_wlan_rssi_monitoring_control
* Unsigned 32-bit value enum qca_wlan_rssi_monitoring_control
*/
QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CONTROL,
/* Unsigned 32-bit value */
QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_REQUEST_ID,
/* Signed 8-bit value in dBm */
QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MAX_RSSI,
/* Signed 8-bit value in dBm */
QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MIN_RSSI,
/* attributes to be used/received in callback */
/* 6-byte MAC address used to represent current BSSID MAC address */
QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CUR_BSSID,
/* Signed 8-bit value indicating the current RSSI */
QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CUR_RSSI,
/* keep last */
QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MAX =
QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_ndp_params - Used by the vendor command
* QCA_NL80211_VENDOR_SUBCMD_NDP.
*/
enum qca_wlan_vendor_attr_ndp_params {
QCA_WLAN_VENDOR_ATTR_NDP_PARAM_INVALID = 0,
/* Unsigned 32-bit value
* enum of sub commands values in qca_wlan_ndp_sub_cmd
*/
QCA_WLAN_VENDOR_ATTR_NDP_SUBCMD,
/* Unsigned 16-bit value */
QCA_WLAN_VENDOR_ATTR_NDP_TRANSACTION_ID,
/* NL attributes for data used NDP SUB cmds */
/* Unsigned 32-bit value indicating a service info */
QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_INSTANCE_ID,
/* Unsigned 32-bit value; channel frequency in MHz */
QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL,
/* Interface Discovery MAC address. An array of 6 Unsigned int8 */
QCA_WLAN_VENDOR_ATTR_NDP_PEER_DISCOVERY_MAC_ADDR,
/* Interface name on which NDP is being created */
QCA_WLAN_VENDOR_ATTR_NDP_IFACE_STR,
/* Unsigned 32-bit value for security */
/* CONFIG_SECURITY is deprecated, use NCS_SK_TYPE/PMK/SCID instead */
QCA_WLAN_VENDOR_ATTR_NDP_CONFIG_SECURITY,
/* Unsigned 32-bit value for QoS */
QCA_WLAN_VENDOR_ATTR_NDP_CONFIG_QOS,
/* Array of u8: len = QCA_WLAN_VENDOR_ATTR_NAN_DP_APP_INFO_LEN */
QCA_WLAN_VENDOR_ATTR_NDP_APP_INFO,
/* Unsigned 32-bit value for NDP instance Id */
QCA_WLAN_VENDOR_ATTR_NDP_INSTANCE_ID,
/* Array of instance Ids */
QCA_WLAN_VENDOR_ATTR_NDP_INSTANCE_ID_ARRAY,
/* Unsigned 32-bit value for initiator/responder NDP response code
* accept/reject
*/
QCA_WLAN_VENDOR_ATTR_NDP_RESPONSE_CODE,
/* NDI MAC address. An array of 6 Unsigned int8 */
QCA_WLAN_VENDOR_ATTR_NDP_NDI_MAC_ADDR,
/* Unsigned 32-bit value errors types returned by driver
* The wifi_nan.h in AOSP project platform/hardware/libhardware_legacy
* NanStatusType includes these values.
*/
QCA_WLAN_VENDOR_ATTR_NDP_DRV_RESPONSE_STATUS_TYPE,
/* Unsigned 32-bit value error values returned by driver
* The nan_i.h in AOSP project platform/hardware/qcom/wlan
* NanInternalStatusType includes these values.
*/
QCA_WLAN_VENDOR_ATTR_NDP_DRV_RETURN_VALUE,
/* Unsigned 32-bit value for Channel setup configuration
* The wifi_nan.h in AOSP project platform/hardware/libhardware_legacy
* NanDataPathChannelCfg includes these values.
*/
QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_CONFIG,
/* Unsigned 32-bit value for Cipher Suite Shared Key Type */
QCA_WLAN_VENDOR_ATTR_NDP_CSID,
/* Array of u8: len = NAN_PMK_INFO_LEN 32 bytes */
QCA_WLAN_VENDOR_ATTR_NDP_PMK,
/* Security Context Identifier that contains the PMKID
* Array of u8: len = NAN_SCID_BUF_LEN 1024 bytes
*/
QCA_WLAN_VENDOR_ATTR_NDP_SCID,
/* Array of u8: len = NAN_SECURITY_MAX_PASSPHRASE_LEN 63 bytes */
QCA_WLAN_VENDOR_ATTR_NDP_PASSPHRASE,
/* Array of u8: len = NAN_MAX_SERVICE_NAME_LEN 255 bytes */
QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_NAME,
/* Unsigned 32-bit bitmap indicating schedule update
* BIT_0: NSS Update
* BIT_1: Channel list update
*/
QCA_WLAN_VENDOR_ATTR_NDP_SCHEDULE_UPDATE_REASON,
/* Unsigned 32-bit value for NSS */
QCA_WLAN_VENDOR_ATTR_NDP_NSS,
/* Unsigned 32-bit value for NUMBER NDP CHANNEL */
QCA_WLAN_VENDOR_ATTR_NDP_NUM_CHANNELS,
/* Unsigned 32-bit value for CHANNEL BANDWIDTH
* 0:20 MHz, 1:40 MHz, 2:80 MHz, 3:160 MHz
*/
QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_WIDTH,
/* Array of channel/band width */
QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_INFO,
/* IPv6 address used by NDP (in network byte order), 16 bytes array.
* This attribute is used and optional for ndp request, ndp response,
* ndp indication, and ndp confirm.
*/
QCA_WLAN_VENDOR_ATTR_NDP_IPV6_ADDR = 27,
/* Unsigned 16-bit value indicating transport port used by NDP.
* This attribute is used and optional for ndp response, ndp indication,
* and ndp confirm.
*/
QCA_WLAN_VENDOR_ATTR_NDP_TRANSPORT_PORT = 28,
/* Unsigned 8-bit value indicating protocol used by NDP and assigned by
* the Internet Assigned Numbers Authority (IANA) as per:
* https://www.iana.org/assignments/protocol-numbers/protocol-numbers.xhtml
* This attribute is used and optional for ndp response, ndp indication,
* and ndp confirm.
*/
QCA_WLAN_VENDOR_ATTR_NDP_TRANSPORT_PROTOCOL = 29,
/* Unsigned 8-bit value indicating if NDP remote peer supports NAN NDPE.
* 1:support 0:not support
*/
QCA_WLAN_VENDOR_ATTR_PEER_NDPE_SUPPORT = 30,
/* keep last */
QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_MAX =
QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_AFTER_LAST - 1,
};
enum qca_wlan_ndp_sub_cmd {
QCA_WLAN_VENDOR_ATTR_NDP_INVALID = 0,
/* Command to create a NAN data path interface */
QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_CREATE = 1,
/* Command to delete a NAN data path interface */
QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_DELETE = 2,
/* Command to initiate a NAN data path session */
QCA_WLAN_VENDOR_ATTR_NDP_INITIATOR_REQUEST = 3,
/* Command to notify if the NAN data path session was sent */
QCA_WLAN_VENDOR_ATTR_NDP_INITIATOR_RESPONSE = 4,
/* Command to respond to NAN data path session */
QCA_WLAN_VENDOR_ATTR_NDP_RESPONDER_REQUEST = 5,
/* Command to notify on the responder about the response */
QCA_WLAN_VENDOR_ATTR_NDP_RESPONDER_RESPONSE = 6,
/* Command to initiate a NAN data path end */
QCA_WLAN_VENDOR_ATTR_NDP_END_REQUEST = 7,
/* Command to notify the if end request was sent */
QCA_WLAN_VENDOR_ATTR_NDP_END_RESPONSE = 8,
/* Command to notify the peer about the end request */
QCA_WLAN_VENDOR_ATTR_NDP_REQUEST_IND = 9,
/* Command to confirm the NAN data path session is complete */
QCA_WLAN_VENDOR_ATTR_NDP_CONFIRM_IND = 10,
/* Command to indicate the peer about the end request being received */
QCA_WLAN_VENDOR_ATTR_NDP_END_IND = 11,
/* Command to indicate the peer of schedule update */
QCA_WLAN_VENDOR_ATTR_NDP_SCHEDULE_UPDATE_IND = 12
};
/**
* enum qca_wlan_vendor_attr_nd_offload - Used by the vendor command
* QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD.
*/
enum qca_wlan_vendor_attr_nd_offload {
QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_INVALID = 0,
/* Flag to set Neighbour Discovery offload */
QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_FLAG,
/* Keep last */
QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_MAX =
QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_AFTER_LAST - 1,
};
/**
* enum packet_filter_sub_cmd - Packet filter sub commands
*/
enum packet_filter_sub_cmd {
/**
* Write packet filter program and/or data. The driver/firmware should
* disable APF before writing into local buffer and re-enable APF after
* writing is done.
*/
QCA_WLAN_SET_PACKET_FILTER = 1,
/* Get packet filter feature capabilities from driver */
QCA_WLAN_GET_PACKET_FILTER = 2,
/**
* Write packet filter program and/or data. User space will send the
* %QCA_WLAN_DISABLE_PACKET_FILTER command before issuing this command
* and will send the %QCA_WLAN_ENABLE_PACKET_FILTER afterwards. The key
* difference from that %QCA_WLAN_SET_PACKET_FILTER is the control over
* enable/disable is given to user space with this command. Also,
* user space sends the length of program portion in the buffer within
* %QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROG_LENGTH.
*/
QCA_WLAN_WRITE_PACKET_FILTER = 3,
/* Read packet filter program and/or data */
QCA_WLAN_READ_PACKET_FILTER = 4,
/* Enable APF feature */
QCA_WLAN_ENABLE_PACKET_FILTER = 5,
/* Disable APF feature */
QCA_WLAN_DISABLE_PACKET_FILTER = 6,
};
/**
* enum qca_wlan_vendor_attr_packet_filter - BPF control commands used by
* vendor QCA_NL80211_VENDOR_SUBCMD_PACKET_FILTER.
*/
enum qca_wlan_vendor_attr_packet_filter {
QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_INVALID = 0,
/* Unsigned 32-bit enum passed using packet_filter_sub_cmd */
QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_SUB_CMD,
/* Unsigned 32-bit value indicating the packet filter version */
QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_VERSION,
/* Unsigned 32-bit value indicating the packet filter id */
QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_ID,
/**
* Unsigned 32-bit value indicating the packet filter size including
* program + data.
*/
QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_SIZE,
/* Unsigned 32-bit value indicating the packet filter current offset */
QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_CURRENT_OFFSET,
/* Program and/or data in bytes */
QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROGRAM,
/* Unsigned 32-bit value of the length of the program section in packet
* filter buffer.
*/
QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROG_LENGTH = 7,
/* keep last */
QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_MAX =
QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_drv_info - WLAN driver info used by vendor command
* QCA_NL80211_VENDOR_SUBCMD_GET_BUS_SIZE.
*/
enum qca_wlan_vendor_drv_info {
QCA_WLAN_VENDOR_ATTR_DRV_INFO_INVALID = 0,
/* Maximum Message size info between firmware & HOST
* Unsigned 32-bit value
*/
QCA_WLAN_VENDOR_ATTR_DRV_INFO_BUS_SIZE,
/* keep last */
QCA_WLAN_VENDOR_ATTR_DRV_INFO_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_DRV_INFO_MAX =
QCA_WLAN_VENDOR_ATTR_DRV_INFO_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_wake_stats - Wake lock stats used by vendor
* command QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS.
*/
enum qca_wlan_vendor_attr_wake_stats {
QCA_WLAN_VENDOR_ATTR_WAKE_STATS_INVALID = 0,
/* Unsigned 32-bit value indicating the total count of wake event */
QCA_WLAN_VENDOR_ATTR_WAKE_STATS_TOTAL_CMD_EVENT_WAKE,
/* Array of individual wake count, each index representing wake reason
*/
QCA_WLAN_VENDOR_ATTR_WAKE_STATS_CMD_EVENT_WAKE_CNT_PTR,
/* Unsigned 32-bit value representing wake count array */
QCA_WLAN_VENDOR_ATTR_WAKE_STATS_CMD_EVENT_WAKE_CNT_SZ,
/* Unsigned 32-bit total wake count value of driver/fw */
QCA_WLAN_VENDOR_ATTR_WAKE_STATS_TOTAL_DRIVER_FW_LOCAL_WAKE,
/* Array of wake stats of driver/fw */
QCA_WLAN_VENDOR_ATTR_WAKE_STATS_DRIVER_FW_LOCAL_WAKE_CNT_PTR,
/* Unsigned 32-bit total wake count value of driver/fw */
QCA_WLAN_VENDOR_ATTR_WAKE_STATS_DRIVER_FW_LOCAL_WAKE_CNT_SZ,
/* Unsigned 32-bit total wake count value of packets received */
QCA_WLAN_VENDOR_ATTR_WAKE_STATS_TOTAL_RX_DATA_WAKE,
/* Unsigned 32-bit wake count value unicast packets received */
QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RX_UNICAST_CNT,
/* Unsigned 32-bit wake count value multicast packets received */
QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RX_MULTICAST_CNT,
/* Unsigned 32-bit wake count value broadcast packets received */
QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RX_BROADCAST_CNT,
/* Unsigned 32-bit wake count value of ICMP packets */
QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP_PKT,
/* Unsigned 32-bit wake count value of ICMP6 packets */
QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_PKT,
/* Unsigned 32-bit value ICMP6 router advertisement */
QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_RA,
/* Unsigned 32-bit value ICMP6 neighbor advertisement */
QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_NA,
/* Unsigned 32-bit value ICMP6 neighbor solicitation */
QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_NS,
/* Unsigned 32-bit wake count value of receive side ICMP4 multicast */
QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP4_RX_MULTICAST_CNT,
/* Unsigned 32-bit wake count value of receive side ICMP6 multicast */
QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_RX_MULTICAST_CNT,
/* Unsigned 32-bit wake count value of receive side multicast */
QCA_WLAN_VENDOR_ATTR_WAKE_STATS_OTHER_RX_MULTICAST_CNT,
/* Unsigned 32-bit wake count value of a given RSSI breach */
QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RSSI_BREACH_CNT,
/* Unsigned 32-bit wake count value of low RSSI */
QCA_WLAN_VENDOR_ATTR_WAKE_STATS_LOW_RSSI_CNT,
/* Unsigned 32-bit value GSCAN count */
QCA_WLAN_VENDOR_ATTR_WAKE_STATS_GSCAN_CNT,
/* Unsigned 32-bit value PNO complete count */
QCA_WLAN_VENDOR_ATTR_WAKE_STATS_PNO_COMPLETE_CNT,
/* Unsigned 32-bit value PNO match count */
QCA_WLAN_VENDOR_ATTR_WAKE_STATS_PNO_MATCH_CNT,
/* keep last */
QCA_WLAN_VENDOR_GET_WAKE_STATS_AFTER_LAST,
QCA_WLAN_VENDOR_GET_WAKE_STATS_MAX =
QCA_WLAN_VENDOR_GET_WAKE_STATS_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_thermal_cmd - Vendor subcmd attributes to set
* cmd value. Used for NL attributes for data used by
* QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD sub command.
*/
enum qca_wlan_vendor_attr_thermal_cmd {
QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_INVALID = 0,
/* The value of command, driver will implement different operations
* according to this value. It uses values defined in
* enum qca_wlan_vendor_attr_thermal_cmd_type.
* u32 attribute.
*/
QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_VALUE = 1,
/* keep last */
QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_MAX =
QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_AFTER_LAST - 1
};
/**
* qca_wlan_vendor_attr_thermal_cmd_type: Attribute values for
* QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_VALUE to the vendor subcmd
* QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD. This represents the
* thermal command types sent to driver.
* @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_PARAMS: Request to
* get thermal shutdown configuration parameters for display. Parameters
* responded from driver are defined in
* enum qca_wlan_vendor_attr_get_thermal_params_rsp.
* @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE: Request to
* get temperature. Host should respond with a temperature data. It is defined
* in enum qca_wlan_vendor_attr_thermal_get_temperature.
* @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SUSPEND: Request to execute thermal
* suspend action.
* @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_RESUME: Request to execute thermal
* resume action.
*/
enum qca_wlan_vendor_attr_thermal_cmd_type {
QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_PARAMS,
QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE,
QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SUSPEND,
QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_RESUME,
};
/**
* enum qca_wlan_vendor_attr_thermal_get_temperature - vendor subcmd attributes
* to get chip temperature by user.
* enum values are used for NL attributes for data used by
* QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE command for data used
* by QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD sub command.
*/
enum qca_wlan_vendor_attr_thermal_get_temperature {
QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_INVALID = 0,
/* Temperature value (degree Celsius) from driver.
* u32 attribute.
*/
QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_DATA,
/* keep last */
QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_MAX =
QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_get_thermal_params_rsp - vendor subcmd attributes
* to get configuration parameters of thermal shutdown feature. Enum values are
* used by QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_PARAMS command for data
* used by QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD sub command.
*/
enum qca_wlan_vendor_attr_get_thermal_params_rsp {
QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_INVALID = 0,
/* Indicate if the thermal shutdown feature is enabled.
* NLA_FLAG attribute.
*/
QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SHUTDOWN_EN,
/* Indicate if the auto mode is enabled.
* Enable: Driver triggers the suspend/resume action.
* Disable: User space triggers the suspend/resume action.
* NLA_FLAG attribute.
*/
QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SHUTDOWN_AUTO_EN,
/* Thermal resume threshold (degree Celsius). Issue the resume command
* if the temperature value is lower than this threshold.
* u16 attribute.
*/
QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_RESUME_THRESH,
/* Thermal warning threshold (degree Celsius). FW reports temperature
* to driver if it's higher than this threshold.
* u16 attribute.
*/
QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_WARNING_THRESH,
/* Thermal suspend threshold (degree Celsius). Issue the suspend command
* if the temperature value is higher than this threshold.
* u16 attribute.
*/
QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SUSPEND_THRESH,
/* FW reports temperature data periodically at this interval (ms).
* u16 attribute.
*/
QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SAMPLE_RATE,
/* keep last */
QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_MAX =
QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_thermal_event - vendor subcmd attributes to
* report thermal events from driver to user space.
* enum values are used for NL attributes for data used by
* QCA_NL80211_VENDOR_SUBCMD_THERMAL_EVENT sub command.
*/
enum qca_wlan_vendor_attr_thermal_event {
QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_INVALID = 0,
/* Temperature value (degree Celsius) from driver.
* u32 attribute.
*/
QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_TEMPERATURE,
/* Indication of resume completion from power save mode.
* NLA_FLAG attribute.
*/
QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_RESUME_COMPLETE,
/* keep last */
QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_MAX =
QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_AFTER_LAST - 1,
};
/**
* enum he_fragmentation_val - HE fragmentation support values
* Indicates level of dynamic fragmentation that is supported by
* a STA as a recipient.
* HE fragmentation values are defined in IEEE P802.11ax/D2.0, 9.4.2.237.2
* (HE MAC Capabilities Information field) and are used in HE Capabilities
* element to advertise the support. These values are validated in the driver
* to check the device capability and advertised in the HE Capabilities
* element. These values are used to configure testbed device to allow the
* advertised hardware capabilities to be downgraded for testing purposes.
*
* @HE_FRAG_DISABLE: no support for dynamic fragmentation
* @HE_FRAG_LEVEL1: support for dynamic fragments that are
* contained within an MPDU or S-MPDU, no support for dynamic fragments
* within an A-MPDU that is not an S-MPDU.
* @HE_FRAG_LEVEL2: support for dynamic fragments that are
* contained within an MPDU or S-MPDU and support for up to one dynamic
* fragment for each MSDU, each A-MSDU if supported by the recipient, and
* each MMPDU within an A-MPDU or multi-TID A-MPDU that is not an
* MPDU or S-MPDU.
* @HE_FRAG_LEVEL3: support for dynamic fragments that are
* contained within an MPDU or S-MPDU and support for multiple dynamic
* fragments for each MSDU and for each A-MSDU if supported by the
* recipient within an A-MPDU or multi-TID AMPDU and up to one dynamic
* fragment for each MMPDU in a multi-TID A-MPDU that is not an S-MPDU.
*/
enum he_fragmentation_val {
HE_FRAG_DISABLE,
HE_FRAG_LEVEL1,
HE_FRAG_LEVEL2,
HE_FRAG_LEVEL3,
};
/**
* enum he_mcs_config - HE MCS support configuration
*
* Configures the HE Tx/Rx MCS map in HE capability IE for given bandwidth.
* These values are used in driver to configure the HE MCS map to advertise
* Tx/Rx MCS map in HE capability and these values are applied for all the
* streams supported by the device. To configure MCS for different bandwidths,
* vendor command needs to be sent using this attribute with appropriate value.
* For example, to configure HE_80_MCS_0_7, send vendor command using HE MCS
* attribute with HE_80_MCS0_7. And to configure HE MCS for HE_160_MCS0_11
* send this command using HE MCS config attribute with value HE_160_MCS0_11.
* These values are used to configure testbed device to allow the advertised
* hardware capabilities to be downgraded for testing purposes. The enum values
* are defined such that BIT[1:0] indicates the MCS map value. Values 3,7 and
* 11 are not used as BIT[1:0] value is 3 which is used to disable MCS map.
* These values are validated in the driver before setting the MCS map and
* driver returns error if the input is other than these enum values.
*
* @HE_80_MCS0_7: support for HE 80/40/20 MHz MCS 0 to 7
* @HE_80_MCS0_9: support for HE 80/40/20 MHz MCS 0 to 9
* @HE_80_MCS0_11: support for HE 80/40/20 MHz MCS 0 to 11
* @HE_160_MCS0_7: support for HE 160 MHz MCS 0 to 7
* @HE_160_MCS0_9: support for HE 160 MHz MCS 0 to 9
* @HE_160_MCS0_11: support for HE 160 MHz MCS 0 to 11
* @HE_80P80_MCS0_7: support for HE 80p80 MHz MCS 0 to 7
* @HE_80P80_MCS0_9: support for HE 80p80 MHz MCS 0 to 9
* @HE_80P80_MCS0_11: support for HE 80p80 MHz MCS 0 to 11
*/
enum he_mcs_config {
HE_80_MCS0_7 = 0,
HE_80_MCS0_9 = 1,
HE_80_MCS0_11 = 2,
HE_160_MCS0_7 = 4,
HE_160_MCS0_9 = 5,
HE_160_MCS0_11 = 6,
HE_80P80_MCS0_7 = 8,
HE_80P80_MCS0_9 = 9,
HE_80P80_MCS0_11 = 10,
};
/**
* enum qca_wlan_ba_session_config - BA session configuration
*
* Indicates the configuration values for BA session configuration attribute.
*
* @QCA_WLAN_ADD_BA: Establish a new BA session with given configuration.
* @QCA_WLAN_DELETE_BA: Delete the existing BA session for given TID.
*/
enum qca_wlan_ba_session_config {
QCA_WLAN_ADD_BA = 1,
QCA_WLAN_DELETE_BA = 2,
};
/**
* enum qca_wlan_ac_type - Access category type
*
* Indicates the access category type value.
*
* @QCA_WLAN_AC_BE: BE access category
* @QCA_WLAN_AC_BK: BK access category
* @QCA_WLAN_AC_VI: VI access category
* @QCA_WLAN_AC_VO: VO access category
* @QCA_WLAN_AC_ALL: All ACs
*/
enum qca_wlan_ac_type {
QCA_WLAN_AC_BE = 0,
QCA_WLAN_AC_BK = 1,
QCA_WLAN_AC_VI = 2,
QCA_WLAN_AC_VO = 3,
QCA_WLAN_AC_ALL = 4,
};
/**
* enum qca_wlan_he_ltf_cfg - HE LTF configuration
*
* Indicates the HE LTF configuration value.
*
* @QCA_WLAN_HE_LTF_AUTO: HE-LTF is automatically set to the mandatory HE-LTF,
* based on the GI setting
* @QCA_WLAN_HE_LTF_1X: 1X HE LTF is 3.2us LTF
* @QCA_WLAN_HE_LTF_2X: 2X HE LTF is 6.4us LTF
* @QCA_WLAN_HE_LTF_4X: 4X HE LTF is 12.8us LTF
*/
enum qca_wlan_he_ltf_cfg {
QCA_WLAN_HE_LTF_AUTO = 0,
QCA_WLAN_HE_LTF_1X = 1,
QCA_WLAN_HE_LTF_2X = 2,
QCA_WLAN_HE_LTF_4X = 3,
};
/**
* enum qca_wlan_he_mac_padding_dur - HE trigger frame MAC padding duration
*
* Indicates the HE trigger frame MAC padding duration value.
*
* @QCA_WLAN_HE_NO_ADDITIONAL_PROCESS_TIME: no additional time required to
* process the trigger frame.
* @QCA_WLAN_HE_8US_OF_PROCESS_TIME: indicates the 8us of processing time for
* trigger frame.
* @QCA_WLAN_HE_16US_OF_PROCESS_TIME: indicates the 16us of processing time for
* trigger frame.
*/
enum qca_wlan_he_mac_padding_dur {
QCA_WLAN_HE_NO_ADDITIONAL_PROCESS_TIME = 0,
QCA_WLAN_HE_8US_OF_PROCESS_TIME = 1,
QCA_WLAN_HE_16US_OF_PROCESS_TIME = 2,
};
/**
* enum qca_wlan_he_om_ctrl_ch_bw - HE OM control field BW configuration
*
* Indicates the HE Operating mode control channel width setting value.
*
* @QCA_WLAN_HE_OM_CTRL_BW_20M: Primary 20 MHz
* @QCA_WLAN_HE_OM_CTRL_BW_40M: Primary 40 MHz
* @QCA_WLAN_HE_OM_CTRL_BW_80M: Primary 80 MHz
* @QCA_WLAN_HE_OM_CTRL_BW_160M: 160 MHz and 80+80 MHz
*/
enum qca_wlan_he_om_ctrl_ch_bw {
QCA_WLAN_HE_OM_CTRL_BW_20M = 0,
QCA_WLAN_HE_OM_CTRL_BW_40M = 1,
QCA_WLAN_HE_OM_CTRL_BW_80M = 2,
QCA_WLAN_HE_OM_CTRL_BW_160M = 3,
};
/**
* enum qca_wlan_vendor_attr_he_omi_tx: Represents attributes for
* HE operating mode control transmit request. These attributes are
* sent as part of QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OMI_TX and
* QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION.
*
* @QCA_WLAN_VENDOR_ATTR_HE_OMI_RX_NSS: Mandatory 8-bit unsigned value
* indicates the maximum number of spatial streams, NSS, that the STA
* supports in reception for PPDU bandwidths less than or equal to 80 MHz
* and is set to NSS - 1.
*
* @QCA_WLAN_VENDOR_ATTR_HE_OMI_CH_BW: Mandatory 8-bit unsigned value
* indicates the operating channel width supported by the STA for both
* reception and transmission. Uses enum qca_wlan_he_om_ctrl_ch_bw values.
*
* @QCA_WLAN_VENDOR_ATTR_HE_OMI_ULMU_DISABLE: Mandatory 8-bit unsigned value
* indicates the all trigger based UL MU operations by the STA.
* 0 - UL MU operations are enabled by the STA.
* 1 - All triggered UL MU transmissions are suspended by the STA.
*
* @QCA_WLAN_VENDOR_ATTR_HE_OMI_TX_NSTS: Mandatory 8-bit unsigned value
* indicates the maximum number of space-time streams, NSTS, that
* the STA supports in transmission and is set to NSTS - 1.
*
* @QCA_WLAN_VENDOR_ATTR_HE_OMI_ULMU_DATA_DISABLE: 8-bit unsigned value
* combined with the UL MU Disable subfield and the recipient's setting
* of the OM Control UL MU Data Disable RX Support subfield in the HE MAC
* capabilities to determine which HE TB PPDUs are possible by the
* STA to transmit.
* 0 - UL MU data operations are enabled by the STA.
* 1 - Determine which HE TB PPDU types are allowed by the STA if UL MU disable
* bit is not set, else UL MU Tx is suspended.
*
*/
enum qca_wlan_vendor_attr_he_omi_tx {
QCA_WLAN_VENDOR_ATTR_HE_OMI_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_HE_OMI_RX_NSS = 1,
QCA_WLAN_VENDOR_ATTR_HE_OMI_CH_BW = 2,
QCA_WLAN_VENDOR_ATTR_HE_OMI_ULMU_DISABLE = 3,
QCA_WLAN_VENDOR_ATTR_HE_OMI_TX_NSTS = 4,
QCA_WLAN_VENDOR_ATTR_HE_OMI_ULMU_DATA_DISABLE = 5,
/* keep last */
QCA_WLAN_VENDOR_ATTR_HE_OMI_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_HE_OMI_MAX =
QCA_WLAN_VENDOR_ATTR_HE_OMI_AFTER_LAST - 1,
};
/* Attributes for data used by
* QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION
*/
enum qca_wlan_vendor_attr_wifi_test_config {
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_INVALID = 0,
/* 8-bit unsigned value to configure the driver to enable/disable
* WMM feature. This attribute is used to configure testbed device.
* 1-enable, 0-disable
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_WMM_ENABLE = 1,
/* 8-bit unsigned value to configure the driver to accept/reject
* the addba request from peer. This attribute is used to configure
* the testbed device.
* 1-accept addba, 0-reject addba
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ACCEPT_ADDBA_REQ = 2,
/* 8-bit unsigned value to configure the driver to send or not to
* send the addba request to peer.
* This attribute is used to configure the testbed device.
* 1-send addba, 0-do not send addba
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_SEND_ADDBA_REQ = 3,
/* 8-bit unsigned value to indicate the HE fragmentation support.
* Uses enum he_fragmentation_val values.
* This attribute is used to configure the testbed device to
* allow the advertised hardware capabilities to be downgraded
* for testing purposes.
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_FRAGMENTATION = 4,
/* 8-bit unsigned value to indicate the HE MCS support.
* Uses enum he_mcs_config values.
* This attribute is used to configure the testbed device to
* allow the advertised hardware capabilities to be downgraded
* for testing purposes.
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MCS = 5,
/* 8-bit unsigned value to configure the driver to allow or not to
* allow the connection with WEP/TKIP in HT/VHT/HE modes.
* This attribute is used to configure the testbed device.
* 1-allow WEP/TKIP in HT/VHT/HE, 0-do not allow WEP/TKIP.
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_WEP_TKIP_IN_HE = 6,
/* 8-bit unsigned value to configure the driver to add a
* new BA session or delete the existing BA session for
* given TID. ADDBA command uses the buffer size and TID
* configuration if user specifies the values else default
* value for buffer size is used for all TIDs if the TID
* also not specified. For DEL_BA command TID value is
* required to process the command.
* Uses enum qca_wlan_ba_session_config values.
* This attribute is used to configure the testbed device.
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ADD_DEL_BA_SESSION = 7,
/* 16-bit unsigned value to configure the buffer size in addba
* request and response frames.
* This attribute is used to configure the testbed device.
* The range of the value is 0 to 256.
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ADDBA_BUFF_SIZE = 8,
/* 8-bit unsigned value to configure the buffer size in addba
* request and response frames.
* This attribute is used to configure the testbed device.
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_BA_TID = 9,
/* 8-bit unsigned value to configure the no ack policy.
* To configure no ack policy, access category value is
* required to process the command.
* This attribute is used to configure the testbed device.
* 1 - enable no ack, 0 - disable no ack.
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ENABLE_NO_ACK = 10,
/* 8-bit unsigned value to configure the AC for no ack policy
* This attribute is used to configure the testbed device.
* Uses the enum qca_wlan_ac_type values.
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_NO_ACK_AC = 11,
/* 8-bit unsigned value to configure the HE LTF
* This attribute is used to configure the testbed device.
* Uses the enum qca_wlan_he_ltf_cfg values.
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_LTF = 12,
/* 8-bit unsigned value to configure the tx beamformee.
* This attribute is used to configure the testbed device.
* 1-enable, 0-disable.
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ENABLE_TX_BEAMFORMEE = 13,
/* 8-bit unsigned value to configure the tx beamformee number
* of space-time streams.
* This attribute is used to configure the testbed device.
* The range of the value is 0 to 8.
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_TX_BEAMFORMEE_NSTS = 14,
/* 8-bit unsigned value to configure the MU EDCA params for given AC
* This attribute is used to configure the testbed device.
* Uses the enum qca_wlan_ac_type values.
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_AC = 15,
/* 8-bit unsigned value to configure the MU EDCA AIFSN for given AC
* To configure MU EDCA AIFSN value, MU EDCA access category value
* is required to process the command.
* This attribute is used to configure the testbed device.
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_AIFSN = 16,
/* 8-bit unsigned value to configure the MU EDCA ECW min value for
* given AC.
* To configure MU EDCA ECW min value, MU EDCA access category value
* is required to process the command.
* This attribute is used to configure the testbed device.
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_ECWMIN = 17,
/* 8-bit unsigned value to configure the MU EDCA ECW max value for
* given AC.
* To configure MU EDCA ECW max value, MU EDCA access category value
* is required to process the command.
* This attribute is used to configure the testbed device.
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_ECWMAX = 18,
/* 8-bit unsigned value to configure the MU EDCA timer for given AC
* To configure MU EDCA timer value, MU EDCA access category value
* is required to process the command.
* This attribute is used to configure the testbed device.
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_TIMER = 19,
/* 8-bit unsigned value to configure the HE trigger frame MAC padding
* duration.
* This attribute is used to configure the testbed device.
* Uses the enum qca_wlan_he_mac_padding_dur values.
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MAC_PADDING_DUR = 20,
/* 8-bit unsigned value to override the MU EDCA params to defaults
* regardless of the AP beacon MU EDCA params. If it is enabled use
* the default values else use the MU EDCA params from AP beacon.
* This attribute is used to configure the testbed device.
* 1-enable, 0-disable.
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_OVERRIDE_MU_EDCA = 21,
/* 8-bit unsigned value to configure the support for receiving
* an MPDU that contains an operating mode control subfield.
* This attribute is used to configure the testbed device.
* 1-enable, 0-disable.
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_SUPP = 22,
/* Nested attribute values required to setup the TWT session.
* enum qca_wlan_vendor_attr_twt_setup provides the necessary
* information to set up the session. It contains broadcast flags,
* set_up flags, trigger value, flow type, flow ID, wake interval
* exponent, protection, target wake time, wake duration, wake interval
* mantissa. These nested attributes are used to setup a host triggered
* TWT session.
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SETUP = 23,
/* This nested attribute is used to terminate the current TWT session.
* It does not currently carry any attributes.
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_TERMINATE = 24,
/* This nested attribute is used to suspend the current TWT session.
* It does not currently carry any attributes.
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SUSPEND = 25,
/* Nested attribute values to indicate the request for resume.
* This attribute is used to resume the TWT session.
* enum qca_wlan_vendor_attr_twt_resume provides the necessary
* parameters required to resume the TWT session.
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_RESUME = 26,
/* 8-bit unsigned value to set the HE operating mode control
* (OM CTRL) Channel Width subfield.
* The Channel Width subfield indicates the operating channel width
* supported by the STA for both reception and transmission.
* Uses the enum qca_wlan_he_om_ctrl_ch_bw values.
* This setting is cleared with the
* QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG
* flag attribute to reset defaults.
* This attribute is used to configure the testbed device.
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_BW = 27,
/* 8-bit unsigned value to configure the number of spatial
* streams in HE operating mode control field.
* This setting is cleared with the
* QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG
* flag attribute to reset defaults.
* This attribute is used to configure the testbed device.
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_NSS = 28,
/* Flag attribute to configure the UL MU disable bit in
* HE operating mode control field.
* This setting is cleared with the
* QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG
* flag attribute to reset defaults.
* This attribute is used to configure the testbed device.
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_UL_MU_DISABLE = 29,
/* Flag attribute to clear the previously set HE operating mode
* control field configuration.
* This attribute is used to configure the testbed device to reset
* defaults to clear any previously set HE operating mode control
* field configuration.
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG = 30,
/* 8-bit unsigned value to configure HE single user PPDU
* transmission. By default this setting is disabled and it
* is disabled in the reset defaults of the device configuration.
* This attribute is used to configure the testbed device.
* 1-enable, 0-disable
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_TX_SUPPDU = 31,
/* 8-bit unsigned value to configure action frame transmission
* in HE trigger based PPDU transmission.
* By default this setting is disabled and it is disabled in
* the reset defaults of the device configuration.
* This attribute is used to configure the testbed device.
* 1-enable, 0-disable
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_ACTION_TX_TB_PPDU = 32,
/* Nested attribute to indicate HE operating mode control field
* transmission. It contains operating mode control field Nss,
* channel bandwidth, Tx Nsts and UL MU disable attributes.
* These nested attributes are used to send HE operating mode control
* with configured values.
* Uses the enum qca_wlan_vendor_attr_he_omi_tx attributes.
* This attribute is used to configure the testbed device.
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OMI_TX = 33,
/* 8-bit unsigned value to configure +HTC_HE support to indicate the
* support for the reception of a frame that carries an HE variant
* HT Control field.
* This attribute is used to configure the testbed device.
* 1-enable, 0-disable
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_HTC_HE_SUPP = 34,
/* 8-bit unsigned value to configure VHT support in 2.4G band.
* This attribute is used to configure the testbed device.
* 1-enable, 0-disable
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ENABLE_2G_VHT = 35,
/* 8-bit unsigned value to configure HE testbed defaults.
* This attribute is used to configure the testbed device.
* 1-set the device HE capabilities to testbed defaults.
* 0-reset the device HE capabilities to supported config.
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_SET_HE_TESTBED_DEFAULTS = 36,
/* 8-bit unsigned value to configure TWT request support.
* This attribute is used to configure the testbed device.
* 1-enable, 0-disable.
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_TWT_REQ_SUPPORT = 37,
/* keep last */
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_MAX =
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_bss_filter - Used by the vendor command
* QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER.
* The user can add/delete the filter by specifying the BSSID/STA MAC address in
* QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR, filter type in
* QCA_WLAN_VENDOR_ATTR_BSS_FILTER_TYPE, add/delete action in
* QCA_WLAN_VENDOR_ATTR_BSS_FILTER_ACTION in the request. The user can get the
* statistics of an unassociated station by specifying the MAC address in
* QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR, station type in
* QCA_WLAN_VENDOR_ATTR_BSS_FILTER_TYPE, GET action in
* QCA_WLAN_VENDOR_ATTR_BSS_FILTER_ACTION in the request. The user also can get
* the statistics of all unassociated stations by specifying the Broadcast MAC
* address (ff:ff:ff:ff:ff:ff) in QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR with
* above procedure. In the response, driver shall specify statistics
* information nested in QCA_WLAN_VENDOR_ATTR_BSS_FILTER_STA_STATS.
*/
enum qca_wlan_vendor_attr_bss_filter {
QCA_WLAN_VENDOR_ATTR_BSS_FILTER_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR = 1,
/* Other BSS filter type, unsigned 8 bit value. One of the values
* in enum qca_wlan_vendor_bss_filter_type.
*/
QCA_WLAN_VENDOR_ATTR_BSS_FILTER_TYPE = 2,
/* Other BSS filter action, unsigned 8 bit value. One of the values
* in enum qca_wlan_vendor_bss_filter_action.
*/
QCA_WLAN_VENDOR_ATTR_BSS_FILTER_ACTION = 3,
/* Array of nested attributes where each entry is the statistics
* information of the specified station that belong to another BSS.
* Attributes for each entry are taken from enum
* qca_wlan_vendor_bss_filter_sta_stats.
* Other BSS station configured in
* QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER with filter type
* QCA_WLAN_VENDOR_BSS_FILTER_TYPE_STA.
* Statistics returned by QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER
* with filter action QCA_WLAN_VENDOR_BSS_FILTER_ACTION_GET.
*/
QCA_WLAN_VENDOR_ATTR_BSS_FILTER_STA_STATS = 4,
/* keep last */
QCA_WLAN_VENDOR_ATTR_BSS_FILTER_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAX =
QCA_WLAN_VENDOR_ATTR_BSS_FILTER_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_bss_filter_type - Type of
* filter used in other BSS filter operations. Used by the vendor command
* QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER.
*
* @QCA_WLAN_VENDOR_BSS_FILTER_TYPE_BSSID: BSSID filter
* @QCA_WLAN_VENDOR_BSS_FILTER_TYPE_STA: Station MAC address filter
*/
enum qca_wlan_vendor_bss_filter_type {
QCA_WLAN_VENDOR_BSS_FILTER_TYPE_BSSID,
QCA_WLAN_VENDOR_BSS_FILTER_TYPE_STA,
};
/**
* enum qca_wlan_vendor_bss_filter_action - Type of
* action in other BSS filter operations. Used by the vendor command
* QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER.
*
* @QCA_WLAN_VENDOR_BSS_FILTER_ACTION_ADD: Add filter
* @QCA_WLAN_VENDOR_BSS_FILTER_ACTION_DEL: Delete filter
* @QCA_WLAN_VENDOR_BSS_FILTER_ACTION_GET: Get the statistics
*/
enum qca_wlan_vendor_bss_filter_action {
QCA_WLAN_VENDOR_BSS_FILTER_ACTION_ADD,
QCA_WLAN_VENDOR_BSS_FILTER_ACTION_DEL,
QCA_WLAN_VENDOR_BSS_FILTER_ACTION_GET,
};
/**
* enum qca_wlan_vendor_bss_filter_sta_stats - Attributes for
* the statistics of a specific unassociated station belonging to another BSS.
* The statistics provides information of the unassociated station
* filtered by other BSS operation - such as MAC, signal value.
* Used by the vendor command QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER.
*
* @QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_MAC: MAC address of the station.
* @QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI: Last received signal strength
* of the station. Unsigned 8 bit number containing RSSI.
* @QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI_TS: Time stamp of the host
* driver for the last received RSSI. Unsigned 64 bit number containing
* nanoseconds from the boottime.
*/
enum qca_wlan_vendor_bss_filter_sta_stats {
QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_INVALID = 0,
QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_MAC = 1,
QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI = 2,
QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI_TS = 3,
/* keep last */
QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_AFTER_LAST,
QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_MAX =
QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_AFTER_LAST - 1
};
/* enum qca_wlan_nan_subcmd_type - Type of NAN command used by attribute
* QCA_WLAN_VENDOR_ATTR_NAN_SUBCMD_TYPE as a part of vendor command
* QCA_NL80211_VENDOR_SUBCMD_NAN_EXT.
*/
enum qca_wlan_nan_ext_subcmd_type {
/* Subcmd of type NAN Enable Request */
QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ = 1,
/* Subcmd of type NAN Disable Request */
QCA_WLAN_NAN_EXT_SUBCMD_TYPE_DISABLE_REQ = 2,
};
/**
* enum qca_wlan_vendor_attr_nan_params - Used by the vendor command
* QCA_NL80211_VENDOR_SUBCMD_NAN_EXT.
*/
enum qca_wlan_vendor_attr_nan_params {
QCA_WLAN_VENDOR_ATTR_NAN_INVALID = 0,
/* Carries NAN command for firmware component. Every vendor command
* QCA_NL80211_VENDOR_SUBCMD_NAN_EXT must contain this attribute with a
* payload containing the NAN command. NLA_BINARY attribute.
*/
QCA_WLAN_VENDOR_ATTR_NAN_CMD_DATA = 1,
/* Indicates the type of NAN command sent with
* QCA_NL80211_VENDOR_SUBCMD_NAN_EXT. enum qca_wlan_nan_ext_subcmd_type
* describes the possible range of values. This attribute is mandatory
* if the command being issued is either
* QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ or
* QCA_WLAN_NAN_EXT_SUBCMD_TYPE_DISABLE_REQ. NLA_U32 attribute.
*/
QCA_WLAN_VENDOR_ATTR_NAN_SUBCMD_TYPE = 2,
/* Frequency (in MHz) of primary NAN discovery social channel in 2.4 GHz
* band. This attribute is mandatory when command type is
* QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ. NLA_U32 attribute.
*/
QCA_WLAN_VENDOR_ATTR_NAN_DISC_24GHZ_BAND_FREQ = 3,
/* Frequency (in MHz) of secondary NAN discovery social channel in 5 GHz
* band. This attribute is optional and should be included when command
* type is QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ and NAN discovery
* has to be started on 5GHz along with 2.4GHz. NLA_U32 attribute.
*/
QCA_WLAN_VENDOR_ATTR_NAN_DISC_5GHZ_BAND_FREQ = 4,
/* keep last */
QCA_WLAN_VENDOR_ATTR_NAN_PARAMS_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_NAN_PARAMS_MAX =
QCA_WLAN_VENDOR_ATTR_NAN_PARAMS_AFTER_LAST - 1
};
/**
* enum qca_wlan_vendor_attr_twt_setup: Represents attributes for
* TWT (Target Wake Time) setup request. These attributes are sent as part of
* %QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SETUP and
* %QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION.
*
* @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST: Flag attribute.
* Disable (flag attribute not present) - Individual TWT
* Enable (flag attribute present) - Broadcast TWT.
* Individual means the session is between the STA and the AP.
* This session is established using a separate negotiation between
* STA and AP.
* Broadcast means the session is across multiple STAs and an AP. The
* configuration parameters are announced in Beacon frames by the AP.
*
* @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_REQ_TYPE: Required (u8).
* Unsigned 8-bit qca_wlan_vendor_twt_setup_req_type to
* specify the TWT request type
*
* @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_TRIGGER: Flag attribute
* Enable (flag attribute present) - TWT with trigger support.
* Disable (flag attribute not present) - TWT without trigger support.
* Trigger means the AP will send the trigger frame to allow STA to send data.
* Without trigger, the STA will wait for the MU EDCA timer before
* transmitting the data.
*
* @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_TYPE: Required (u8)
* 0 - Announced TWT - In this mode, STA may skip few service periods to
* save more power. If STA wants to wake up, it will send a PS-POLL/QoS
* NULL frame to AP.
* 1 - Unannounced TWT - The STA will wakeup during every SP.
*
* @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_ID: Optional (u8)
* Flow ID is the unique identifier for each TWT session.
* Currently this is not required and dialog ID will be set to zero.
*
* @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_EXP: Required (u8)
* This attribute (exp) is used along with the mantissa to derive the
* wake interval using the following formula:
* pow(2,exp) = wake_intvl_us/wake_intvl_mantis
* Wake interval is the interval between 2 successive SP.
*
* @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_PROTECTION: Flag attribute
* Enable (flag attribute present) - Protection required.
* Disable (flag attribute not present) - Protection not required.
* If protection is enabled, then the AP will use protection
* mechanism using RTS/CTS to self to reserve the airtime.
*
* @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME: Optional (u32)
* This attribute is used as the SP offset which is the offset from
* TSF after which the wake happens. The units are in microseconds. If
* this attribute is not provided, then the value will be set to zero.
*
* @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_DURATION: Required (u32)
* This is the duration of the service period. The units are in TU.
*
* @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_MANTISSA: Required (u32)
* This attribute is used to configure wake interval mantissa.
* The units are in TU.
*/
enum qca_wlan_vendor_attr_twt_setup {
QCA_WLAN_VENDOR_ATTR_TWT_SETUP_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST = 1,
QCA_WLAN_VENDOR_ATTR_TWT_SETUP_REQ_TYPE = 2,
QCA_WLAN_VENDOR_ATTR_TWT_SETUP_TRIGGER = 3,
QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_TYPE = 4,
QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_ID = 5,
QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_EXP = 6,
QCA_WLAN_VENDOR_ATTR_TWT_SETUP_PROTECTION = 7,
QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME = 8,
QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_DURATION = 9,
QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_MANTISSA = 10,
/* keep last */
QCA_WLAN_VENDOR_ATTR_TWT_SETUP_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAX =
QCA_WLAN_VENDOR_ATTR_TWT_SETUP_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_twt_resume: Represents attributes for
* TWT (Target Wake Time) resume request. These attributes are sent as part of
* %QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_RESUME and
* %QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION.
*
* @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT: Optional (u8)
* This attribute is used as the SP offset which is the offset from
* TSF after which the wake happens. The units are in microseconds.
* If this attribute is not provided, then the value will be set to
* zero.
*
* @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT_SIZE: Required (u32)
* This attribute represents the next TWT subfield size.
*/
enum qca_wlan_vendor_attr_twt_resume {
QCA_WLAN_VENDOR_ATTR_TWT_RESUME_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT = 1,
QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT_SIZE = 2,
/* keep last */
QCA_WLAN_VENDOR_ATTR_TWT_RESUME_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_TWT_RESUME_MAX =
QCA_WLAN_VENDOR_ATTR_TWT_RESUME_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_twt_setup_req_type - Required (u8)
* Represents the setup type being requested for TWT.
* @QCA_WLAN_VENDOR_TWT_SETUP_REQUEST: STA is not specifying all the TWT
* parameters but relying on AP to fill the parameters during the negotiation.
* @QCA_WLAN_VENDOR_TWT_SETUP_SUGGEST: STA will provide all the suggested
* values which the AP may accept or AP may provide alternative parameters
* which the STA may accept.
* @QCA_WLAN_VENDOR_TWT_SETUP_DEMAND: STA is not willing to accept any
* alternate parameters than the requested ones.
*/
enum qca_wlan_vendor_twt_setup_req_type {
QCA_WLAN_VENDOR_TWT_SETUP_REQUEST = 1,
QCA_WLAN_VENDOR_TWT_SETUP_SUGGEST = 2,
QCA_WLAN_VENDOR_TWT_SETUP_DEMAND = 3,
};
/**
* enum qca_wlan_roam_scan_event_type - Type of roam scan event
*
* Indicates the type of roam scan event sent by firmware/driver.
*
* @QCA_WLAN_ROAM_SCAN_TRIGGER_EVENT: Roam scan trigger event type.
* @QCA_WLAN_ROAM_SCAN_STOP_EVENT: Roam scan stopped event type.
*/
enum qca_wlan_roam_scan_event_type {
QCA_WLAN_ROAM_SCAN_TRIGGER_EVENT = 0,
QCA_WLAN_ROAM_SCAN_STOP_EVENT = 1,
};
/**
* enum qca_wlan_roam_scan_trigger_reason - Roam scan trigger reason
*
* Indicates the reason for triggering roam scan by firmware/driver.
*
* @QCA_WLAN_ROAM_SCAN_TRIGGER_REASON_LOW_RSSI: Due to low RSSI of current AP.
* @QCA_WLAN_ROAM_SCAN_TRIGGER_REASON_HIGH_PER: Due to high packet error rate.
*/
enum qca_wlan_roam_scan_trigger_reason {
QCA_WLAN_ROAM_SCAN_TRIGGER_REASON_LOW_RSSI = 0,
QCA_WLAN_ROAM_SCAN_TRIGGER_REASON_HIGH_PER = 1,
};
/**
* enum qca_wlan_vendor_attr_roam_scan - Vendor subcmd attributes to report
* roam scan related details from driver/firmware to user space. enum values
* are used for NL attributes sent with
* %QCA_NL80211_VENDOR_SUBCMD_ROAM_SCAN_EVENT sub command.
*/
enum qca_wlan_vendor_attr_roam_scan {
QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_INVALID = 0,
/* Encapsulates type of roam scan event being reported. enum
* qca_wlan_roam_scan_event_type describes the possible range of
* values. u32 attribute.
*/
QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_EVENT_TYPE = 1,
/* Encapsulates reason for triggering roam scan. enum
* qca_wlan_roam_scan_trigger_reason describes the possible range of
* values. u32 attribute.
*/
QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_TRIGGER_REASON = 2,
/* keep last */
QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_MAX =
QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_cfr_method - QCA vendor CFR methods used by
* attribute QCA_WLAN_VENDOR_ATTR_PEER_CFR_METHOD as part of vendor
* command QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG.
*/
enum qca_wlan_vendor_cfr_method {
/* CFR method using QOS Null frame */
QCA_WLAN_VENDOR_CFR_METHOD_QOS_NULL = 0,
};
/**
* enum qca_wlan_vendor_peer_cfr_capture_attr - Used by the vendor command
* QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG to configure peer
* Channel Frequency Response capture parameters and enable periodic CFR
* capture.
*/
enum qca_wlan_vendor_peer_cfr_capture_attr {
QCA_WLAN_VENDOR_ATTR_PEER_CFR_CAPTURE_INVALID = 0,
/* 6-byte MAC address of the peer.
* This attribute is mandatory.
*/
QCA_WLAN_VENDOR_ATTR_CFR_PEER_MAC_ADDR = 1,
/* Enable peer CFR Capture, flag attribute.
* This attribute is mandatory to enable peer CFR capture.
* If this attribute is not present, peer CFR capture is disabled.
*/
QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE = 2,
/* BW of measurement, attribute uses the values in enum nl80211_chan_width
* Supported values: 20, 40, 80, 80+80, 160.
* Note that all targets may not support all bandwidths.
* u8 attribute. This attribute is mandatory if attribute
* QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE is used.
*/
QCA_WLAN_VENDOR_ATTR_PEER_CFR_BANDWIDTH = 3,
/* Periodicity of CFR measurement in msec.
* Periodicity should be a multiple of Base timer.
* Current Base timer value supported is 10 msecs (default).
* 0 for one shot capture. u32 attribute.
* This attribute is mandatory if attribute
* QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE is used.
*/
QCA_WLAN_VENDOR_ATTR_PEER_CFR_PERIODICITY = 4,
/* Method used to capture Channel Frequency Response.
* Attribute uses the values defined in enum qca_wlan_vendor_cfr_method.
* u8 attribute. This attribute is mandatory if attribute
* QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE is used.
*/
QCA_WLAN_VENDOR_ATTR_PEER_CFR_METHOD = 5,
/* Enable periodic CFR capture, flag attribute.
* This attribute is mandatory to enable Periodic CFR capture.
* If this attribute is not present, periodic CFR capture is disabled.
*/
QCA_WLAN_VENDOR_ATTR_PERIODIC_CFR_CAPTURE_ENABLE = 6,
/* Keep last */
QCA_WLAN_VENDOR_ATTR_PEER_CFR_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_PEER_CFR_MAX =
QCA_WLAN_VENDOR_ATTR_PEER_CFR_AFTER_LAST - 1,
};
/**
* enum qca_wlan_throughput_level - Current throughput level
*
* Indicates the current level of throughput calculated by the driver. The
* driver may choose different thresholds to decide whether the throughput level
* is low or medium or high based on variety of parameters like physical link
* capacity of the current connection, the number of packets being dispatched
* per second, etc. The throughput level events might not be consistent with the
* actual current throughput value being observed.
*
* @QCA_WLAN_THROUGHPUT_LEVEL_LOW: Low level of throughput
* @QCA_WLAN_THROUGHPUT_LEVEL_MEDIUM: Medium level of throughput
* @QCA_WLAN_THROUGHPUT_LEVEL_HIGH: High level of throughput
*/
enum qca_wlan_throughput_level {
QCA_WLAN_THROUGHPUT_LEVEL_LOW = 0,
QCA_WLAN_THROUGHPUT_LEVEL_MEDIUM = 1,
QCA_WLAN_THROUGHPUT_LEVEL_HIGH = 2,
};
/**
* enum qca_wlan_vendor_attr_throughput_change - Vendor subcmd attributes to
* report throughput changes from the driver to user space. enum values are used
* for netlink attributes sent with
* %QCA_NL80211_VENDOR_SUBCMD_THROUGHPUT_CHANGE_EVENT sub command.
*/
enum qca_wlan_vendor_attr_throughput_change {
QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_INVALID = 0,
/* Indicates the direction of throughput in which the change is being
* reported. u8 attribute. Value is 0 for TX and 1 for RX.
*/
QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_DIRECTION = 1,
/* Indicates the newly observed throughput level. enum
* qca_wlan_throughput_level describes the possible range of values.
* u8 attribute.
*/
QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_THROUGHPUT_LEVEL = 2,
/* Indicates the driver's guidance on the new value to be set to
* kernel's TCP parameter tcp_limit_output_bytes. u32 attribute. The
* driver may optionally include this attribute.
*/
QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_TCP_LIMIT_OUTPUT_BYTES = 3,
/* Indicates the driver's guidance on the new value to be set to
* kernel's TCP parameter tcp_adv_win_scale. s8 attribute. Possible
* values are from -31 to 31. The driver may optionally include this
* attribute.
*/
QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_TCP_ADV_WIN_SCALE = 4,
/* Indicates the driver's guidance on the new value to be set to
* kernel's TCP parameter tcp_delack_seg. u32 attribute. The driver may
* optionally include this attribute.
*/
QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_TCP_DELACK_SEG = 5,
/* keep last */
QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_MAX =
QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_AFTER_LAST - 1,
};
/**
* enum qca_coex_config_profiles - This enum defines different types of
* traffic streams that can be prioritized one over the other during coex
* scenarios.
* The types defined in this enum are categorized in the below manner.
* 0 - 31 values corresponds to WLAN
* 32 - 63 values corresponds to BT
* 64 - 95 values corresponds to Zigbee
* @QCA_WIFI_STA_DISCOVERY: Prioritize discovery frames for WLAN STA
* @QCA_WIFI_STA_CONNECTION: Prioritize connection frames for WLAN STA
* @QCA_WIFI_STA_CLASS_3_MGMT: Prioritize class 3 mgmt frames for WLAN STA
* @QCA_WIFI_STA_DATA : Prioritize data frames for WLAN STA
* @QCA_WIFI_STA_ALL: Priritize all frames for WLAN STA
* @QCA_WIFI_SAP_DISCOVERY: Prioritize discovery frames for WLAN SAP
* @QCA_WIFI_SAP_CONNECTION: Prioritize connection frames for WLAN SAP
* @QCA_WIFI_SAP_CLASS_3_MGMT: Prioritize class 3 mgmt frames for WLAN SAP
* @QCA_WIFI_SAP_DATA: Prioritize data frames for WLAN SAP
* @QCA_WIFI_SAP_ALL: Prioritize all frames for WLAN SAP
* @QCA_BT_A2DP: Prioritize BT A2DP
* @QCA_BT_BLE: Prioritize BT BLE
* @QCA_BT_SCO: Prioritize BT SCO
* @QCA_ZB_LOW: Prioritize Zigbee Low
* @QCA_ZB_HIGH: Prioritize Zigbee High
*/
enum qca_coex_config_profiles {
/* 0 - 31 corresponds to WLAN */
QCA_WIFI_STA_DISCOVERY = 0,
QCA_WIFI_STA_CONNECTION = 1,
QCA_WIFI_STA_CLASS_3_MGMT = 2,
QCA_WIFI_STA_DATA = 3,
QCA_WIFI_STA_ALL = 4,
QCA_WIFI_SAP_DISCOVERY = 5,
QCA_WIFI_SAP_CONNECTION = 6,
QCA_WIFI_SAP_CLASS_3_MGMT = 7,
QCA_WIFI_SAP_DATA = 8,
QCA_WIFI_SAP_ALL = 9,
QCA_WIFI_CASE_MAX = 31,
/* 32 - 63 corresponds to BT */
QCA_BT_A2DP = 32,
QCA_BT_BLE = 33,
QCA_BT_SCO = 34,
QCA_BT_CASE_MAX = 63,
/* 64 - 95 corresponds to Zigbee */
QCA_ZB_LOW = 64,
QCA_ZB_HIGH = 65,
QCA_ZB_CASE_MAX = 95,
/* 0xff is default value if the u8 profile value is not set. */
QCA_COEX_CONFIG_PROFILE_DEFAULT_VALUE = 255
};
/**
* enum qca_vendor_attr_coex_config_types - Coex configurations types.
* This enum defines the valid set of values of coex configuration types. These
* values may used by attribute
* %QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_CONFIG_TYPE.
*
* @QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_COEX_RESET: Reset all the
* weights to default values.
* @QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_COEX_START: Start to config
* weights with configurability value.
*/
enum qca_vendor_attr_coex_config_types {
QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_COEX_RESET = 1,
QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_COEX_START = 2,
};
/**
* enum qca_vendor_attr_coex_config - Specifies vendor coex config attributes
*
* @QCA_VENDOR_ATTR_COEX_CONFIG_PROFILES: This attribute contains variable
* length array of 8-bit values from enum qca_coex_config_profiles.
* FW will prioritize the profiles in the order given in the array encapsulated
* in this attribute.
* For example:
* -----------------------------------------------------------------------
* | 1 | 34 | 32 | 65 |
* -----------------------------------------------------------------------
* If the attribute contains the values defined in above array then it means
* 1) Wifi STA connection has priority over BT_SCO, BT_A2DP and ZIGBEE HIGH.
* 2) BT_SCO has priority over BT_A2DP.
* 3) BT_A2DP has priority over ZIGBEE HIGH.
* Profiles which are not listed in this array shall not be preferred over the
* profiles which are listed in the array as a part of this attribute.
*/
enum qca_vendor_attr_coex_config {
QCA_VENDOR_ATTR_COEX_CONFIG_INVALID = 0,
QCA_VENDOR_ATTR_COEX_CONFIG_PROFILES = 1,
/* Keep last */
QCA_VENDOR_ATTR_COEX_CONFIG_AFTER_LAST,
QCA_VENDOR_ATTR_COEX_CONFIG_MAX =
QCA_VENDOR_ATTR_COEX_CONFIG_AFTER_LAST - 1,
};
/**
* enum qca_vendor_attr_coex_config_three_way - Specifies vendor coex config
* attributes
* Attributes for data used by QCA_NL80211_VENDOR_SUBCMD_COEX_CONFIG
*
* QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_CONFIG_TYPE: u32 attribute.
* Indicate config type.
* The config types are 32-bit values from qca_vendor_attr_coex_config_types
*
* @QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_1: u32 attribute.
* Indicate the Priority 1 profiles.
* The profiles are 8-bit values from enum qca_coex_config_profiles.
* In same priority level, maximum to 4 profiles can be set here.
* @QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_2: u32 attribute.
* Indicate the Priority 2 profiles.
* The profiles are 8-bit values from enum qca_coex_config_profiles.
* In same priority level, maximum to 4 profiles can be set here.
* @QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_3: u32 attribute.
* Indicate the Priority 3 profiles.
* The profiles are 8-bit values from enum qca_coex_config_profiles.
* In same priority level, maximum to 4 profiles can be set here.
* @QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_4: u32 attribute.
* Indicate the Priority 4 profiles.
* The profiles are 8-bit values from enum qca_coex_config_profiles.
* In same priority level, maximum to 4 profiles can be set here.
* NOTE:
* Limitations for QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_x priority
* arrangement:
* 1: In the same u32 attribute (priority x), the profiles enum values own
* same priority level.
* 2: 0xff is default value if the u8 profile value is not set.
* 3: max to 4 rules/profiles in same priority level.
* 4: max to 4 priority level (priority 1 - priority 4)
* 5: one priority level only supports one scenario from WLAN/BT/ZB,
* hybrid rules not support.
* 6: if WMI_COEX_CONFIG_THREE_WAY_COEX_RESET called, priority x will
* remain blank to reset all parameters.
* For example:
*
* If the attributes as follow:
* priority 1:
* ------------------------------------
* | 0xff | 0 | 1 | 2 |
* ------------------------------------
* priority 2:
* -------------------------------------
* | 0xff | 0xff | 0xff | 32 |
* -------------------------------------
* priority 3:
* -------------------------------------
* | 0xff | 0xff | 0xff | 65 |
* -------------------------------------
* then it means:
* 1: WIFI_STA_DISCOVERY, WIFI_STA_CLASS_3_MGMT and WIFI_STA_CONNECTION
* owns same priority level.
* 2: WIFI_STA_DISCOVERY, WIFI_STA_CLASS_3_MGMT and WIFI_STA_CONNECTION
* has priority over BT_A2DP and ZB_HIGH.
* 3: BT_A2DP has priority over ZB_HIGH.
*/
enum qca_vendor_attr_coex_config_three_way {
QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_INVALID = 0,
QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_CONFIG_TYPE = 1,
QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_1 = 2,
QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_2 = 3,
QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_3 = 4,
QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_4 = 5,
/* Keep last */
QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_AFTER_LAST,
QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_MAX =
QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_AFTER_LAST - 1,
};
/**
* enum qca_wlan_vendor_attr_link_properties - Represent the link properties.
*
* @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAC_ADDR: MAC address of the peer
* (STA/AP) for the connected link.
* @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_STA_FLAGS: Attribute containing a
* &struct nl80211_sta_flag_update for the respective connected link. MAC
* address of the peer represented by
* QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAC_ADDR.
*/
enum qca_wlan_vendor_attr_link_properties {
QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_INVALID = 0,
/* 1 - 3 are reserved */
QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAC_ADDR = 4,
QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_STA_FLAGS = 5,
/* Keep last */
QCA_VENDOR_ATTR_LINK_PROPERTIES_AFTER_LAST,
QCA_VENDOR_ATTR_LINK_PROPERTIES_MAX =
QCA_VENDOR_ATTR_LINK_PROPERTIES_AFTER_LAST - 1,
};
/**
* enum qca_vendor_attr_peer_stats_cache_type - Represents peer stats cache type
* This enum defines the valid set of values of peer stats cache types. These
* values are used by attribute
* %QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_TYPE.
*
* @QCA_WLAN_VENDOR_ATTR_PEER_TX_RATE_STATS: Represents peer TX rate statistics
* @QCA_WLAN_VENDOR_ATTR_PEER_RX_RATE_STATS: Represents peer RX rate statistics
* @QCA_WLAN_VENDOR_ATTR_PEER_TX_SOJOURN_STATS: Represents peer TX sojourn
* statistics
*/
enum qca_vendor_attr_peer_stats_cache_type {
QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_TYPE_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_PEER_TX_RATE_STATS,
QCA_WLAN_VENDOR_ATTR_PEER_RX_RATE_STATS,
QCA_WLAN_VENDOR_ATTR_PEER_TX_SOJOURN_STATS,
};
/**
* enum qca_wlan_vendor_attr_peer_stats_cache_params - This enum defines
* attributes required for QCA_NL80211_VENDOR_SUBCMD_PEER_STATS_CACHE_FLUSH
* Information in these attributes is used to flush peer rate statistics from
* the driver to user application.
*
* @QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_TYPE: Unsigned 32-bit attribute
* Indicate peer statistics cache type.
* The statistics types are 32-bit values from
* enum qca_vendor_attr_peer_stats_cache_type.
* @QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_PEER_MAC: Unsigned 8-bit array
* of size 6 octets, representing the peer MAC address.
* @QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_DATA: Opaque data attribute
* containing buffer of statistics to send to application layer entity.
* @QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_PEER_COOKIE: Unsigned 64-bit attribute
* representing a cookie for peer unique session.
*/
enum qca_wlan_vendor_attr_peer_stats_cache_params {
QCA_WLAN_VENDOR_ATTR_PEER_STATS_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_TYPE = 1,
QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_PEER_MAC = 2,
QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_DATA = 3,
QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_PEER_COOKIE = 4,
/* Keep last */
QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_LAST,
QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_MAX =
QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_LAST - 1
};
/**
* enum qca_mpta_helper_attr_zigbee_state - Current Zigbee state
* This enum defines all the possible states of Zigbee, which can be
* delivered in the QCA_MPTA_HELPER_VENDOR_ATTR_ZIGBEE_STATE attribute.
*
* @ZIGBEE_IDLE: Zigbee in idle state
* @ZIGBEE_FORM_NETWORK: Zigbee forming network
* @ZIGBEE_WAIT_JOIN: Zigbee waiting for joining network
* @ZIGBEE_JOIN: Zigbee joining network
* @ZIGBEE_NETWORK_UP: Zigbee network is up
* @ZIGBEE_HMI: Zigbee in HMI mode
*/
enum qca_mpta_helper_attr_zigbee_state {
ZIGBEE_IDLE = 0,
ZIGBEE_FORM_NETWORK = 1,
ZIGBEE_WAIT_JOIN = 2,
ZIGBEE_JOIN = 3,
ZIGBEE_NETWORK_UP = 4,
ZIGBEE_HMI = 5,
};
/*
* enum qca_mpta_helper_vendor_attr - Attributes used in vendor sub-command
* QCA_NL80211_VENDOR_SUBCMD_MPTA_HELPER_CONFIG.
*/
enum qca_mpta_helper_vendor_attr {
QCA_MPTA_HELPER_VENDOR_ATTR_INVALID = 0,
/* Optional attribute used to update Zigbee state.
* enum qca_mpta_helper_attr_zigbee_state.
* NLA_U32 attribute.
*/
QCA_MPTA_HELPER_VENDOR_ATTR_ZIGBEE_STATE = 1,
/* Optional attribute used to configure WLAN duration for Shape-OCS
* during interrupt.
* Set in pair with QCA_MPTA_HELPER_VENDOR_ATTR_INT_NON_WLAN_DURATION.
* Value range 0 ~ 300 (ms).
* NLA_U32 attribute.
*/
QCA_MPTA_HELPER_VENDOR_ATTR_INT_WLAN_DURATION = 2,
/* Optional attribute used to configure non-WLAN duration for Shape-OCS
* during interrupt.
* Set in pair with QCA_MPTA_HELPER_VENDOR_ATTR_INT_WLAN_DURATION.
* Value range 0 ~ 300 (ms).
* NLA_U32 attribute.
*/
QCA_MPTA_HELPER_VENDOR_ATTR_INT_NON_WLAN_DURATION = 3,
/* Optional attribute used to configure WLAN duration for Shape-OCS
* monitor period.
* Set in pair with QCA_MPTA_HELPER_VENDOR_ATTR_MON_NON_WLAN_DURATION.
* Value range 0 ~ 300 (ms)
* NLA_U32 attribute
*/
QCA_MPTA_HELPER_VENDOR_ATTR_MON_WLAN_DURATION = 4,
/* Optional attribute used to configure non-WLAN duration for Shape-OCS
* monitor period.
* Set in pair with QCA_MPTA_HELPER_VENDOR_ATTR_MON_WLAN_DURATION.
* Value range 0 ~ 300 (ms)
* NLA_U32 attribute
*/
QCA_MPTA_HELPER_VENDOR_ATTR_MON_NON_WLAN_DURATION = 5,
/* Optional attribute used to configure OCS interrupt duration.
* Set in pair with QCA_MPTA_HELPER_VENDOR_ATTR_MON_OCS_DURATION.
* Value range 1000 ~ 20000 (ms)
* NLA_U32 attribute
*/
QCA_MPTA_HELPER_VENDOR_ATTR_INT_OCS_DURATION = 6,
/* Optional attribute used to configure OCS monitor duration.
* Set in pair with QCA_MPTA_HELPER_VENDOR_ATTR_INT_OCS_DURATION.
* Value range 1000 ~ 20000 (ms)
* NLA_U32 attribute
*/
QCA_MPTA_HELPER_VENDOR_ATTR_MON_OCS_DURATION = 7,
/* Optional attribute used to notify WLAN firmware the current Zigbee
* channel.
* Value range 11 ~ 26
* NLA_U32 attribute
*/
QCA_MPTA_HELPER_VENDOR_ATTR_ZIGBEE_CHAN = 8,
/* Optional attribute used to configure WLAN mute duration.
* Value range 0 ~ 400 (ms)
* NLA_U32 attribute
*/
QCA_MPTA_HELPER_VENDOR_ATTR_WLAN_MUTE_DURATION = 9,
/* keep last */
QCA_MPTA_HELPER_VENDOR_ATTR_AFTER_LAST,
QCA_MPTA_HELPER_VENDOR_ATTR_MAX =
QCA_MPTA_HELPER_VENDOR_ATTR_AFTER_LAST - 1
};
#endif /* QCA_VENDOR_H */