/*
* NS16550 Serial Port
* originally from linux source (arch/powerpc/boot/ns16550.h)
*
* Cleanup and unification
* (C) 2009 by Detlev Zundel, DENX Software Engineering GmbH
*
* modified slightly to
* have addresses as offsets from CONFIG_SYS_ISA_BASE
* added a few more definitions
* added prototypes for ns16550.c
* reduced no of com ports to 2
* modifications (c) Rob Taylor, Flying Pig Systems. 2000.
*
* added support for port on 64-bit bus
* by Richard Danter (richard.danter@windriver.com), (C) 2005 Wind River Systems
*/
/*
* Note that the following macro magic uses the fact that the compiler
* will not allocate storage for arrays of size 0
*/
#include <linux/types.h>
#ifdef CONFIG_DM_SERIAL
/*
* For driver model we always use one byte per register, and sort out the
* differences in the driver
*/
#define CONFIG_SYS_NS16550_REG_SIZE (-1)
#endif
#if !defined(CONFIG_SYS_NS16550_REG_SIZE) || (CONFIG_SYS_NS16550_REG_SIZE == 0)
#error "Please define NS16550 registers size."
#elif defined(CONFIG_SYS_NS16550_MEM32) && !defined(CONFIG_DM_SERIAL)
#define UART_REG(x) u32 x
#elif (CONFIG_SYS_NS16550_REG_SIZE > 0)
#define UART_REG(x) \
unsigned char prepad_##x[CONFIG_SYS_NS16550_REG_SIZE - 1]; \
unsigned char x;
#elif (CONFIG_SYS_NS16550_REG_SIZE < 0)
#define UART_REG(x) \
unsigned char x; \
unsigned char postpad_##x[-CONFIG_SYS_NS16550_REG_SIZE - 1];
#endif
/**
* struct ns16550_platdata - information about a NS16550 port
*
* @base: Base register address
* @reg_shift: Shift size of registers (0=byte, 1=16bit, 2=32bit...)
* @clock: UART base clock speed in Hz
*/
struct ns16550_platdata {
unsigned long base;
int reg_shift;
int clock;
int reg_offset;
u32 fcr;
};
struct udevice;
struct NS16550 {
UART_REG(rbr); /* 0 */
UART_REG(ier); /* 1 */
UART_REG(fcr); /* 2 */
UART_REG(lcr); /* 3 */
UART_REG(mcr); /* 4 */
UART_REG(lsr); /* 5 */
UART_REG(msr); /* 6 */
UART_REG(spr); /* 7 */
#ifdef CONFIG_SOC_DA8XX
UART_REG(reg8); /* 8 */
UART_REG(reg9); /* 9 */
UART_REG(revid1); /* A */
UART_REG(revid2); /* B */
UART_REG(pwr_mgmt); /* C */
UART_REG(mdr1); /* D */
#else
UART_REG(mdr1); /* 8 */
UART_REG(reg9); /* 9 */
UART_REG(regA); /* A */
UART_REG(regB); /* B */
UART_REG(regC); /* C */
UART_REG(regD); /* D */
UART_REG(regE); /* E */
UART_REG(uasr); /* F */
UART_REG(scr); /* 10*/
UART_REG(ssr); /* 11*/
#endif
#ifdef CONFIG_DM_SERIAL
struct ns16550_platdata *plat;
#endif
};
#define thr rbr
#define iir fcr
#define dll rbr
#define dlm ier
typedef struct NS16550 *NS16550_t;
/*
* These are the definitions for the FIFO Control Register
*/
#define UART_FCR_FIFO_EN 0x01 /* Fifo enable */
#define UART_FCR_CLEAR_RCVR 0x02 /* Clear the RCVR FIFO */
#define UART_FCR_CLEAR_XMIT 0x04 /* Clear the XMIT FIFO */
#define UART_FCR_DMA_SELECT 0x08 /* For DMA applications */
#define UART_FCR_TRIGGER_MASK 0xC0 /* Mask for the FIFO trigger range */
#define UART_FCR_TRIGGER_1 0x00 /* Mask for trigger set at 1 */
#define UART_FCR_TRIGGER_4 0x40 /* Mask for trigger set at 4 */
#define UART_FCR_TRIGGER_8 0x80 /* Mask for trigger set at 8 */
#define UART_FCR_TRIGGER_14 0xC0 /* Mask for trigger set at 14 */
#define UART_FCR_RXSR 0x02 /* Receiver soft reset */
#define UART_FCR_TXSR 0x04 /* Transmitter soft reset */
/* Ingenic JZ47xx specific UART-enable bit. */
#define UART_FCR_UME 0x10
/* Clear & enable FIFOs */
#define UART_FCR_DEFVAL (UART_FCR_FIFO_EN | \
UART_FCR_RXSR | \
UART_FCR_TXSR)
/*
* These are the definitions for the Modem Control Register
*/
#define UART_MCR_DTR 0x01 /* DTR */
#define UART_MCR_RTS 0x02 /* RTS */
#define UART_MCR_OUT1 0x04 /* Out 1 */
#define UART_MCR_OUT2 0x08 /* Out 2 */
#define UART_MCR_LOOP 0x10 /* Enable loopback test mode */
#define UART_MCR_AFE 0x20 /* Enable auto-RTS/CTS */
#define UART_MCR_DMA_EN 0x04
#define UART_MCR_TX_DFR 0x08
/*
* These are the definitions for the Line Control Register
*
* Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting
* UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits.
*/
#define UART_LCR_WLS_MSK 0x03 /* character length select mask */
#define UART_LCR_WLS_5 0x00 /* 5 bit character length */
#define UART_LCR_WLS_6 0x01 /* 6 bit character length */
#define UART_LCR_WLS_7 0x02 /* 7 bit character length */
#define UART_LCR_WLS_8 0x03 /* 8 bit character length */
#define UART_LCR_STB 0x04 /* # stop Bits, off=1, on=1.5 or 2) */
#define UART_LCR_PEN 0x08 /* Parity eneble */
#define UART_LCR_EPS 0x10 /* Even Parity Select */
#define UART_LCR_STKP 0x20 /* Stick Parity */
#define UART_LCR_SBRK 0x40 /* Set Break */
#define UART_LCR_BKSE 0x80 /* Bank select enable */
#define UART_LCR_DLAB 0x80 /* Divisor latch access bit */
/*
* These are the definitions for the Line Status Register
*/
#define UART_LSR_DR 0x01 /* Data ready */
#define UART_LSR_OE 0x02 /* Overrun */
#define UART_LSR_PE 0x04 /* Parity error */
#define UART_LSR_FE 0x08 /* Framing error */
#define UART_LSR_BI 0x10 /* Break */
#define UART_LSR_THRE 0x20 /* Xmit holding register empty */
#define UART_LSR_TEMT 0x40 /* Xmitter empty */
#define UART_LSR_ERR 0x80 /* Error */
#define UART_MSR_DCD 0x80 /* Data Carrier Detect */
#define UART_MSR_RI 0x40 /* Ring Indicator */
#define UART_MSR_DSR 0x20 /* Data Set Ready */
#define UART_MSR_CTS 0x10 /* Clear to Send */
#define UART_MSR_DDCD 0x08 /* Delta DCD */
#define UART_MSR_TERI 0x04 /* Trailing edge ring indicator */
#define UART_MSR_DDSR 0x02 /* Delta DSR */
#define UART_MSR_DCTS 0x01 /* Delta CTS */
/*
* These are the definitions for the Interrupt Identification Register
*/
#define UART_IIR_NO_INT 0x01 /* No interrupts pending */
#define UART_IIR_ID 0x06 /* Mask for the interrupt ID */
#define UART_IIR_MSI 0x00 /* Modem status interrupt */
#define UART_IIR_THRI 0x02 /* Transmitter holding register empty */
#define UART_IIR_RDI 0x04 /* Receiver data interrupt */
#define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */
/*
* These are the definitions for the Interrupt Enable Register
*/
#define UART_IER_MSI 0x08 /* Enable Modem status interrupt */
#define UART_IER_RLSI 0x04 /* Enable receiver line status interrupt */
#define UART_IER_THRI 0x02 /* Enable Transmitter holding register int. */
#define UART_IER_RDI 0x01 /* Enable receiver data interrupt */
/* useful defaults for LCR */
#define UART_LCR_8N1 0x03
void NS16550_init(NS16550_t com_port, int baud_divisor);
void NS16550_putc(NS16550_t com_port, char c);
char NS16550_getc(NS16550_t com_port);
int NS16550_tstc(NS16550_t com_port);
void NS16550_reinit(NS16550_t com_port, int baud_divisor);
/**
* ns16550_calc_divisor() - calculate the divisor given clock and baud rate
*
* Given the UART input clock and required baudrate, calculate the divisor
* that should be used.
*
* @port: UART port
* @clock: UART input clock speed in Hz
* @baudrate: Required baud rate
* @return baud rate divisor that should be used
*/
int ns16550_calc_divisor(NS16550_t port, int clock, int baudrate);
/**
* ns16550_serial_ofdata_to_platdata() - convert DT to platform data
*
* Decode a device tree node for an ns16550 device. This includes the
* register base address and register shift properties. The caller must set
* up the clock frequency.
*
* @dev: dev to decode platform data for
* @return: 0 if OK, -EINVAL on error
*/
int ns16550_serial_ofdata_to_platdata(struct udevice *dev);
/**
* ns16550_serial_probe() - probe a serial port
*
* This sets up the serial port ready for use, except for the baud rate
* @return 0, or -ve on error
*/
int ns16550_serial_probe(struct udevice *dev);
/**
* struct ns16550_serial_ops - ns16550 serial operations
*
* These should be used by the client driver for the driver's 'ops' member
*/
extern const struct dm_serial_ops ns16550_serial_ops;