/* SPDX-License-Identifier: GPL-2.0 */
/*
* Copyright (C) Marvell International Ltd. and its affiliates
*/
#ifndef _MV_DDR_PLAT_H
#define _MV_DDR_PLAT_H
#define MAX_INTERFACE_NUM 1
#define MAX_BUS_NUM 5
#define DDR_IF_CTRL_SUBPHYS_NUM 3
#define DFS_LOW_FREQ_VALUE 120
#define SDRAM_CS_SIZE 0xfffffff /* FIXME: implement a function for cs size for each platform */
#define INTER_REGS_BASE SOC_REGS_PHY_BASE
#define AP_INT_REG_START_ADDR 0xd0000000
#define AP_INT_REG_END_ADDR 0xd0100000
/* Controler bus divider 1 for 32 bit, 2 for 64 bit */
#define DDR_CONTROLLER_BUS_WIDTH_MULTIPLIER 1
/* Tune internal training params values */
#define TUNE_TRAINING_PARAMS_CK_DELAY 160
#define TUNE_TRAINING_PARAMS_PHYREG3VAL 0xA
#define TUNE_TRAINING_PARAMS_PRI_DATA 123
#define TUNE_TRAINING_PARAMS_NRI_DATA 123
#define TUNE_TRAINING_PARAMS_PRI_CTRL 74
#define TUNE_TRAINING_PARAMS_NRI_CTRL 74
#define TUNE_TRAINING_PARAMS_P_ODT_DATA 45
#define TUNE_TRAINING_PARAMS_N_ODT_DATA 45
#define TUNE_TRAINING_PARAMS_P_ODT_CTRL 45
#define TUNE_TRAINING_PARAMS_N_ODT_CTRL 45
#define TUNE_TRAINING_PARAMS_DIC 0x2
#define TUNE_TRAINING_PARAMS_ODT_CONFIG_2CS 0x120012
#define TUNE_TRAINING_PARAMS_ODT_CONFIG_1CS 0x10000
#define TUNE_TRAINING_PARAMS_RTT_NOM 0x44
#define TUNE_TRAINING_PARAMS_RTT_WR_1CS 0x0 /*off*/
#define TUNE_TRAINING_PARAMS_RTT_WR_2CS 0x0 /*off*/
#define MARVELL_BOARD MARVELL_BOARD_ID_BASE
#define REG_DEVICE_SAR1_ADDR 0xe4204
#define RST2_CPU_DDR_CLOCK_SELECT_IN_OFFSET 17
#define RST2_CPU_DDR_CLOCK_SELECT_IN_MASK 0x1f
#define DEVICE_SAMPLE_AT_RESET2_REG 0x18604
#define DEVICE_SAMPLE_AT_RESET2_REG_REFCLK_OFFSET 0
#define DEVICE_SAMPLE_AT_RESET2_REG_REFCLK_25MHZ 0
#define DEVICE_SAMPLE_AT_RESET2_REG_REFCLK_40MHZ 1
/* DRAM Windows */
#define REG_XBAR_WIN_5_CTRL_ADDR 0x20050
#define REG_XBAR_WIN_5_BASE_ADDR 0x20054
/* DRAM Windows */
#define REG_XBAR_WIN_4_CTRL_ADDR 0x20040
#define REG_XBAR_WIN_4_BASE_ADDR 0x20044
#define REG_XBAR_WIN_4_REMAP_ADDR 0x20048
#define REG_XBAR_WIN_7_REMAP_ADDR 0x20078
#define REG_XBAR_WIN_16_CTRL_ADDR 0x200d0
#define REG_XBAR_WIN_16_BASE_ADDR 0x200d4
#define REG_XBAR_WIN_16_REMAP_ADDR 0x200dc
#define REG_XBAR_WIN_19_CTRL_ADDR 0x200e8
#define REG_FASTPATH_WIN_BASE_ADDR(win) (0x20180 + (0x8 * win))
#define REG_FASTPATH_WIN_CTRL_ADDR(win) (0x20184 + (0x8 * win))
#define CPU_CONFIGURATION_REG(id) (0x21800 + (id * 0x100))
#define CPU_MRVL_ID_OFFSET 0x10
#define SAR1_CPU_CORE_MASK 0x00000018
#define SAR1_CPU_CORE_OFFSET 3
/* SatR defined too change topology busWidth and ECC configuration */
#define DDR_SATR_CONFIG_MASK_WIDTH 0x8
#define DDR_SATR_CONFIG_MASK_ECC 0x10
#define DDR_SATR_CONFIG_MASK_ECC_PUP 0x20
#define REG_SAMPLE_RESET_HIGH_ADDR 0x18600
#define MV_BOARD_REFCLK_25MHZ 25000000
#define MV_BOARD_REFCLK MV_BOARD_REFCLK_25MHZ
#define MAX_DQ_NUM 40
/* dram line buffer registers */
#define DLB_CTRL_REG 0x1700
#define DLB_EN_OFFS 0
#define DLB_EN_MASK 0x1
#define DLB_EN_ENA 1
#define DLB_EN_DIS 0
#define WR_COALESCE_EN_OFFS 2
#define WR_COALESCE_EN_MASK 0x1
#define WR_COALESCE_EN_ENA 1
#define WR_COALESCE_EN_DIS 0
#define AXI_PREFETCH_EN_OFFS 3
#define AXI_PREFETCH_EN_MASK 0x1
#define AXI_PREFETCH_EN_ENA 1
#define AXI_PREFETCH_EN_DIS 0
#define MBUS_PREFETCH_EN_OFFS 4
#define MBUS_PREFETCH_EN_MASK 0x1
#define MBUS_PREFETCH_EN_ENA 1
#define MBUS_PREFETCH_EN_DIS 0
#define PREFETCH_NXT_LN_SZ_TRIG_OFFS 6
#define PREFETCH_NXT_LN_SZ_TRIG_MASK 0x1
#define PREFETCH_NXT_LN_SZ_TRIG_ENA 1
#define PREFETCH_NXT_LN_SZ_TRIG_DIS 0
#define DLB_BUS_OPT_WT_REG 0x1704
#define DLB_AGING_REG 0x1708
#define DLB_EVICTION_CTRL_REG 0x170c
#define DLB_EVICTION_TIMERS_REG 0x1710
#define DLB_USER_CMD_REG 0x1714
#define DLB_WTS_DIFF_CS_REG 0x1770
#define DLB_WTS_DIFF_BG_REG 0x1774
#define DLB_WTS_SAME_BG_REG 0x1778
#define DLB_WTS_CMDS_REG 0x177c
#define DLB_WTS_ATTR_PRIO_REG 0x1780
#define DLB_QUEUE_MAP_REG 0x1784
#define DLB_SPLIT_REG 0x1788
/* Subphy result control per byte registers */
#define RESULT_CONTROL_BYTE_PUP_0_REG 0x1830
#define RESULT_CONTROL_BYTE_PUP_1_REG 0x1834
#define RESULT_CONTROL_BYTE_PUP_2_REG 0x1838
#define RESULT_CONTROL_BYTE_PUP_3_REG 0x183c
#define RESULT_CONTROL_BYTE_PUP_4_REG 0x18b0
/* Subphy result control per bit registers */
#define RESULT_CONTROL_PUP_0_BIT_0_REG 0x18b4
#define RESULT_CONTROL_PUP_0_BIT_1_REG 0x18b8
#define RESULT_CONTROL_PUP_0_BIT_2_REG 0x18bc
#define RESULT_CONTROL_PUP_0_BIT_3_REG 0x18c0
#define RESULT_CONTROL_PUP_0_BIT_4_REG 0x18c4
#define RESULT_CONTROL_PUP_0_BIT_5_REG 0x18c8
#define RESULT_CONTROL_PUP_0_BIT_6_REG 0x18cc
#define RESULT_CONTROL_PUP_0_BIT_7_REG 0x18f0
#define RESULT_CONTROL_PUP_1_BIT_0_REG 0x18f4
#define RESULT_CONTROL_PUP_1_BIT_1_REG 0x18f8
#define RESULT_CONTROL_PUP_1_BIT_2_REG 0x18fc
#define RESULT_CONTROL_PUP_1_BIT_3_REG 0x1930
#define RESULT_CONTROL_PUP_1_BIT_4_REG 0x1934
#define RESULT_CONTROL_PUP_1_BIT_5_REG 0x1938
#define RESULT_CONTROL_PUP_1_BIT_6_REG 0x193c
#define RESULT_CONTROL_PUP_1_BIT_7_REG 0x19b0
#define RESULT_CONTROL_PUP_2_BIT_0_REG 0x19b4
#define RESULT_CONTROL_PUP_2_BIT_1_REG 0x19b8
#define RESULT_CONTROL_PUP_2_BIT_2_REG 0x19bc
#define RESULT_CONTROL_PUP_2_BIT_3_REG 0x19c0
#define RESULT_CONTROL_PUP_2_BIT_4_REG 0x19c4
#define RESULT_CONTROL_PUP_2_BIT_5_REG 0x19c8
#define RESULT_CONTROL_PUP_2_BIT_6_REG 0x19cc
#define RESULT_CONTROL_PUP_2_BIT_7_REG 0x19f0
#define RESULT_CONTROL_PUP_3_BIT_0_REG 0x19f4
#define RESULT_CONTROL_PUP_3_BIT_1_REG 0x19f8
#define RESULT_CONTROL_PUP_3_BIT_2_REG 0x19fc
#define RESULT_CONTROL_PUP_3_BIT_3_REG 0x1a30
#define RESULT_CONTROL_PUP_3_BIT_4_REG 0x1a34
#define RESULT_CONTROL_PUP_3_BIT_5_REG 0x1a38
#define RESULT_CONTROL_PUP_3_BIT_6_REG 0x1a3c
#define RESULT_CONTROL_PUP_3_BIT_7_REG 0x1ab0
#define RESULT_CONTROL_PUP_4_BIT_0_REG 0x1ab4
#define RESULT_CONTROL_PUP_4_BIT_1_REG 0x1ab8
#define RESULT_CONTROL_PUP_4_BIT_2_REG 0x1abc
#define RESULT_CONTROL_PUP_4_BIT_3_REG 0x1ac0
#define RESULT_CONTROL_PUP_4_BIT_4_REG 0x1ac4
#define RESULT_CONTROL_PUP_4_BIT_5_REG 0x1ac8
#define RESULT_CONTROL_PUP_4_BIT_6_REG 0x1acc
#define RESULT_CONTROL_PUP_4_BIT_7_REG 0x1af0
/* CPU */
#define REG_BOOTROM_ROUTINE_ADDR 0x182d0
#define REG_BOOTROM_ROUTINE_DRAM_INIT_OFFS 12
/* Matrix enables DRAM modes (bus width/ECC) per boardId */
#define TOPOLOGY_UPDATE_32BIT 0
#define TOPOLOGY_UPDATE_32BIT_ECC 1
#define TOPOLOGY_UPDATE_16BIT 2
#define TOPOLOGY_UPDATE_16BIT_ECC 3
#define TOPOLOGY_UPDATE_16BIT_ECC_PUP3 4
#define TOPOLOGY_UPDATE { \
/* 32Bit, 32bit ECC, 16bit, 16bit ECC PUP4, 16bit ECC PUP3 */ \
{1, 1, 1, 1, 1}, /* RD_NAS_68XX_ID */ \
{1, 1, 1, 1, 1}, /* DB_68XX_ID */ \
{1, 0, 1, 0, 1}, /* RD_AP_68XX_ID */ \
{1, 0, 1, 0, 1}, /* DB_AP_68XX_ID */ \
{1, 0, 1, 0, 1}, /* DB_GP_68XX_ID */ \
{0, 0, 1, 1, 0}, /* DB_BP_6821_ID */ \
{1, 1, 1, 1, 1} /* DB_AMC_6820_ID */ \
};
enum {
CPU_1066MHZ_DDR_400MHZ,
CPU_RESERVED_DDR_RESERVED0,
CPU_667MHZ_DDR_667MHZ,
CPU_800MHZ_DDR_800MHZ,
CPU_RESERVED_DDR_RESERVED1,
CPU_RESERVED_DDR_RESERVED2,
CPU_RESERVED_DDR_RESERVED3,
LAST_FREQ
};
/* struct used for DLB configuration array */
struct dlb_config {
u32 reg_addr;
u32 reg_data;
};
#define ACTIVE_INTERFACE_MASK 0x1
extern u32 dmin_phy_reg_table[][2];
extern u16 odt_slope[];
extern u16 odt_intercept[];
int mv_ddr_pre_training_soc_config(const char *ddr_type);
int mv_ddr_post_training_soc_config(const char *ddr_type);
void mv_ddr_mem_scrubbing(void);
void mv_ddr_odpg_enable(void);
void mv_ddr_odpg_disable(void);
void mv_ddr_odpg_done_clr(void);
int mv_ddr_is_odpg_done(u32 count);
void mv_ddr_training_enable(void);
int mv_ddr_is_training_done(u32 count, u32 *result);
u32 mv_ddr_dm_pad_get(void);
int mv_ddr_pre_training_fixup(void);
int mv_ddr_post_training_fixup(void);
int mv_ddr_manual_cal_do(void);
int ddr3_calc_mem_cs_size(u32 cs, uint64_t *cs_size);
#endif /* _MV_DDR_PLAT_H */