// SPDX-License-Identifier: GPL-2.0+
/*
 *  Copyright (C) 2012 Lucas Stach
 */

#include <common.h>
#include <asm/arch/clock.h>
#include <asm/arch/funcmux.h>
#include <asm/arch/pinmux.h>
#include <asm/arch-tegra/ap.h>
#include <asm/arch-tegra/board.h>
#include <asm/arch-tegra/tegra.h>
#include <asm/gpio.h>
#include <asm/io.h>
#include <i2c.h>
#include <nand.h>
#include "../common/tdx-common.h"

DECLARE_GLOBAL_DATA_PTR;

#define PMU_I2C_ADDRESS		0x34
#define MAX_I2C_RETRY		3
#define PMU_SUPPLYENE		0x14
#define PMU_SUPPLYENE_SYSINEN	(1<<5)
#define PMU_SUPPLYENE_EXITSLREQ	(1<<1)

int arch_misc_init(void)
{
	/* Disable PMIC sleep mode on low supply voltage */
	struct udevice *dev;
	u8 addr, data[1];
	int err;

	err = i2c_get_chip_for_busnum(0, PMU_I2C_ADDRESS, 1, &dev);
	if (err) {
		debug("%s: Cannot find PMIC I2C chip\n", __func__);
		return err;
	}

	addr = PMU_SUPPLYENE;

	err = dm_i2c_read(dev, addr, data, 1);
	if (err) {
		debug("failed to get PMU_SUPPLYENE\n");
		return err;
	}

	data[0] &= ~PMU_SUPPLYENE_SYSINEN;
	data[0] |= PMU_SUPPLYENE_EXITSLREQ;

	err = dm_i2c_write(dev, addr, data, 1);
	if (err) {
		debug("failed to set PMU_SUPPLYENE\n");
		return err;
	}

	/* make sure SODIMM pin 87 nRESET_OUT is released properly */
	pinmux_set_func(PMUX_PINGRP_ATA, PMUX_FUNC_GMI);

	if (readl(NV_PA_BASE_SRAM + NVBOOTINFOTABLE_BOOTTYPE) ==
	    NVBOOTTYPE_RECOVERY)
		printf("USB recovery mode\n");

	return 0;
}

int checkboard(void)
{
	printf("Model: Toradex Colibri T20 %dMB V%s\n",
	       (gd->ram_size == 0x10000000) ? 256 : 512,
	       (get_nand_dev_by_index(0)->erasesize >> 10 == 512) ?
	       ((gd->ram_size == 0x10000000) ? "1.1B" : "1.1C") : "1.2A");

	return 0;
}

#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
int ft_board_setup(void *blob, bd_t *bd)
{
	return ft_common_board_setup(blob, bd);
}
#endif

#ifdef CONFIG_MMC_SDHCI_TEGRA
/*
 * Routine: pin_mux_mmc
 * Description: setup the pin muxes/tristate values for the SDMMC(s)
 */
void pin_mux_mmc(void)
{
	funcmux_select(PERIPH_ID_SDMMC4, FUNCMUX_SDMMC4_ATB_GMA_4_BIT);
	pinmux_tristate_disable(PMUX_PINGRP_GMB);
}
#endif

#ifdef CONFIG_TEGRA_NAND
void pin_mux_nand(void)
{
	funcmux_select(PERIPH_ID_NDFLASH, FUNCMUX_NDFLASH_KBC_8_BIT);

	/*
	 * configure pingroup ATC to something unrelated to
	 * avoid ATC overriding KBC
	 */
	pinmux_set_func(PMUX_PINGRP_ATC, PMUX_FUNC_GMI);
}
#endif

#ifdef CONFIG_USB_EHCI_TEGRA
void pin_mux_usb(void)
{
	/* module internal USB bus to connect ethernet chipset */
	funcmux_select(PERIPH_ID_USB2, FUNCMUX_USB2_ULPI);

	/* ULPI reference clock output */
	pinmux_set_func(PMUX_PINGRP_CDEV2, PMUX_FUNC_PLLP_OUT4);
	pinmux_tristate_disable(PMUX_PINGRP_CDEV2);

	/* PHY reset GPIO */
	pinmux_tristate_disable(PMUX_PINGRP_UAC);

	/* VBus GPIO */
	pinmux_tristate_disable(PMUX_PINGRP_DTE);

	/* Reset ASIX using LAN_RESET */
	gpio_request(TEGRA_GPIO(V, 4), "LAN_RESET");
	gpio_direction_output(TEGRA_GPIO(V, 4), 0);
	pinmux_tristate_disable(PMUX_PINGRP_GPV);
	udelay(5);
	gpio_set_value(TEGRA_GPIO(V, 4), 1);

	/* USBH_PEN: USB 1 aka Tegra USB port 3 VBus */
	pinmux_tristate_disable(PMUX_PINGRP_SPIG);
}
#endif

#ifdef CONFIG_VIDEO_TEGRA20
/*
 * Routine: pin_mux_display
 * Description: setup the pin muxes/tristate values for the LCD interface)
 */
void pin_mux_display(void)
{
	/*
	 * Manually untristate BL_ON (PT4 - SODIMM 71) as specified through
	 * device-tree
	 */
	pinmux_tristate_disable(PMUX_PINGRP_DTA);

	pinmux_set_func(PMUX_PINGRP_SDC, PMUX_FUNC_PWM);
	pinmux_tristate_disable(PMUX_PINGRP_SDC);
}
#endif