/** @file
Serial I/O Port library functions with no library constructor/destructor
Copyright (c) 2008 - 2009, Apple Inc. All rights reserved.<BR>
Copyright (c) 2015, Intel Corporation. All rights reserved.<BR>
This program and the accompanying materials
are licensed and made available under the terms and conditions of the BSD License
which accompanies this distribution. The full text of the license may be found at
http://opensource.org/licenses/bsd-license.php
THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
**/
#include <Base.h>
#include <Library/DebugLib.h>
#include <Library/SerialPortLib.h>
#include <Library/PcdLib.h>
#include <Library/IoLib.h>
#include <Library/OmapLib.h>
#include <Omap3530/Omap3530.h>
/*
Programmed hardware of Serial port.
@return Always return EFI_UNSUPPORTED.
**/
RETURN_STATUS
EFIAPI
SerialPortInitialize (
VOID
)
{
// assume assembly code at reset vector has setup UART
return RETURN_SUCCESS;
}
/**
Write data to serial device.
@param Buffer Point of data buffer which need to be writed.
@param NumberOfBytes Number of output bytes which are cached in Buffer.
@retval 0 Write data failed.
@retval !0 Actual number of bytes writed to serial device.
**/
UINTN
EFIAPI
SerialPortWrite (
IN UINT8 *Buffer,
IN UINTN NumberOfBytes
)
{
UINT32 LSR = UartBase(PcdGet32(PcdOmap35xxConsoleUart)) + UART_LSR_REG;
UINT32 THR = UartBase(PcdGet32(PcdOmap35xxConsoleUart)) + UART_THR_REG;
UINTN Count;
for (Count = 0; Count < NumberOfBytes; Count++, Buffer++) {
while ((MmioRead8(LSR) & UART_LSR_TX_FIFO_E_MASK) == UART_LSR_TX_FIFO_E_NOT_EMPTY);
MmioWrite8(THR, *Buffer);
}
return NumberOfBytes;
}
/**
Read data from serial device and save the datas in buffer.
@param Buffer Point of data buffer which need to be writed.
@param NumberOfBytes Number of output bytes which are cached in Buffer.
@retval 0 Read data failed.
@retval !0 Aactual number of bytes read from serial device.
**/
UINTN
EFIAPI
SerialPortRead (
OUT UINT8 *Buffer,
IN UINTN NumberOfBytes
)
{
UINT32 LSR = UartBase(PcdGet32(PcdOmap35xxConsoleUart)) + UART_LSR_REG;
UINT32 RBR = UartBase(PcdGet32(PcdOmap35xxConsoleUart)) + UART_RBR_REG;
UINTN Count;
for (Count = 0; Count < NumberOfBytes; Count++, Buffer++) {
while ((MmioRead8(LSR) & UART_LSR_RX_FIFO_E_MASK) == UART_LSR_RX_FIFO_E_EMPTY);
*Buffer = MmioRead8(RBR);
}
return NumberOfBytes;
}
/**
Check to see if any data is avaiable to be read from the debug device.
@retval EFI_SUCCESS At least one byte of data is avaiable to be read
@retval EFI_NOT_READY No data is avaiable to be read
@retval EFI_DEVICE_ERROR The serial device is not functioning properly
**/
BOOLEAN
EFIAPI
SerialPortPoll (
VOID
)
{
UINT32 LSR = UartBase(PcdGet32(PcdOmap35xxConsoleUart)) + UART_LSR_REG;
if ((MmioRead8(LSR) & UART_LSR_RX_FIFO_E_MASK) == UART_LSR_RX_FIFO_E_NOT_EMPTY) {
return TRUE;
} else {
return FALSE;
}
}
/**
Sets the control bits on a serial device.
@param[in] Control Sets the bits of Control that are settable.
@retval RETURN_SUCCESS The new control bits were set on the serial device.
@retval RETURN_UNSUPPORTED The serial device does not support this operation.
@retval RETURN_DEVICE_ERROR The serial device is not functioning correctly.
**/
RETURN_STATUS
EFIAPI
SerialPortSetControl (
IN UINT32 Control
)
{
return RETURN_UNSUPPORTED;
}
/**
Retrieve the status of the control bits on a serial device.
@param[out] Control A pointer to return the current control signals from the serial device.
@retval RETURN_SUCCESS The control bits were read from the serial device.
@retval RETURN_UNSUPPORTED The serial device does not support this operation.
@retval RETURN_DEVICE_ERROR The serial device is not functioning correctly.
**/
RETURN_STATUS
EFIAPI
SerialPortGetControl (
OUT UINT32 *Control
)
{
*Control = 0;
if (!SerialPortPoll ()) {
*Control = EFI_SERIAL_INPUT_BUFFER_EMPTY;
}
return RETURN_SUCCESS;
}
/**
Sets the baud rate, receive FIFO depth, transmit/receice time out, parity,
data bits, and stop bits on a serial device.
@param BaudRate The requested baud rate. A BaudRate value of 0 will use the
device's default interface speed.
On output, the value actually set.
@param ReveiveFifoDepth The requested depth of the FIFO on the receive side of the
serial interface. A ReceiveFifoDepth value of 0 will use
the device's default FIFO depth.
On output, the value actually set.
@param Timeout The requested time out for a single character in microseconds.
This timeout applies to both the transmit and receive side of the
interface. A Timeout value of 0 will use the device's default time
out value.
On output, the value actually set.
@param Parity The type of parity to use on this serial device. A Parity value of
DefaultParity will use the device's default parity value.
On output, the value actually set.
@param DataBits The number of data bits to use on the serial device. A DataBits
vaule of 0 will use the device's default data bit setting.
On output, the value actually set.
@param StopBits The number of stop bits to use on this serial device. A StopBits
value of DefaultStopBits will use the device's default number of
stop bits.
On output, the value actually set.
@retval RETURN_SUCCESS The new attributes were set on the serial device.
@retval RETURN_UNSUPPORTED The serial device does not support this operation.
@retval RETURN_INVALID_PARAMETER One or more of the attributes has an unsupported value.
@retval RETURN_DEVICE_ERROR The serial device is not functioning correctly.
**/
RETURN_STATUS
EFIAPI
SerialPortSetAttributes (
IN OUT UINT64 *BaudRate,
IN OUT UINT32 *ReceiveFifoDepth,
IN OUT UINT32 *Timeout,
IN OUT EFI_PARITY_TYPE *Parity,
IN OUT UINT8 *DataBits,
IN OUT EFI_STOP_BITS_TYPE *StopBits
)
{
return RETURN_UNSUPPORTED;
}