/*
 * Copyright (C) 2016 The Android Open Source Project
 *
 * Licensed under the Apache License, Version 2.0 (the "License");
 * you may not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *
 *      http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 */

#ifndef _APP_RELOC_FORMAT_H_
#define _APP_RELOC_FORMAT_H_


/*
 * INTRODUCTION
 *
 * This is the relocation format we use for Cortex-M4F cpu. This format is
 * consistent with what GCC will produce with our app-compilation flags. So
 * what will it produce? Relocs will ONLY be in RAM, always be word-sized,
 * always be word-aligned, and never overlap. We use all of that. How do we
 * encode? The relocs format is a bytestream. The decoder is conceptually two
 * passes, though it can easily be implemented as a single pass. The first pass
 * unpacks the bytestream into a list of TOKENS and NUMBERS. The second then
 * uses those to reconstruct the list of relocs.
 *
 *
 * PASS #1 - unpacking
 *
 * Each iteration, it will read a byte from the input byte stream, until none
 * are available. This first byte will tell it what to do next. All values that
 * are <= MAX_8_BIT_NUM, are put directly as a NUMBER into the output list.
 * The remaining possibly values all require special handling, which will be
 * described now:
 *  TOKEN_32BIT_OFST:      4 bytes follow. They are to be treated as a single
 *                          32-bit little-endian value. This value is put into
 *                          the output list directly as a NUMBER.
 *  TOKEN_24BIT_OFST:      3 bytes follow. They are to be treated as a single
 *                          24-bit little-endian value. MAX_16_BIT_NUM is added
 *                          to it, then this value is put into the output list
 *                          as a NUMBER.
 *  TOKEN_16BIT_OFST:      2 bytes follow. They are to be treated as a single
 *                          16-bit little-endian value. MAX_8_BIT_NUM is added
 *                          to it, then this value is put into the output list
 *                          as a NUMBER.
 *  TOKEN_CONSECUTIVE:     1 byte follows. It is read, MIN_RUN_LEN is added to
 *                          it. That many zero-valued NUMBERS are added to the
 *                          output list.
 *  TOKEN_RELOC_TYPE_CHG:  1 byte follows. It is read, one is added to it, and
 *                          a TYPE_CHANGE token with that value is added to the
 *                          output list.
 *  TOKEN_RELOC_TYPE_NEXT: a TYPE_CHANGE token with a value of 1 is added to
 *                          the output list.
 *
 *
 * PASS #2 - decoding
 *
 * The decoder is stateful. Initially the decoder state is representable as:
 * {reloc_type: 0, ofst: 0}. The decoder will work by removig one item at a
 * time from the head of the list generated by PASS #1, and acting on it, until
 * no more exist. It will produce {reloc_type, reloc_offset} tuples, which can
 * then be used to perform actual relocations. Unpon reading a TYPE_CHANGE
 * token, "reloc_type" in the decoder's state shall be incremented by the value
 * the token carries, and "ofst" shall be set to zero. Upon reading a NUMBER,
 * the decoder shall:
 *   a. calculate t = "ofst" + (that NUMBER's value) * 4
 *   b. store t + 4 into "ofst"
 *   c. produce an output tuple {"reloc_type", t}
 *
 *
 * At the end of these two passes a list of tuples exists that has all reloc types
 * and offsets. this list can be easily walked and relocations performed.
 */



//offset is always from previous reloc's NEXT word!
#define TOKEN_RELOC_TYPE_NEXT	0xFF // reloc type changed to previous + 1
#define TOKEN_RELOC_TYPE_CHG	0xFE // reloc type changed (followed by a byte represeting "reloc_type" increment minus 1)
#define TOKEN_CONSECUTIVE	0xFD // followed by 8-bit number of directly following words to relocate (in addition to the one we relocated using previous reloc) minus 3 (2 is break-even point)
#define TOKEN_16BIT_OFST	0xFC // followed by 16-bit x, such that the value we want to represent is x + MAX_8_BIT_NUM
#define TOKEN_24BIT_OFST	0xFB // followed by 24-bit x, such that the value we want to represent is x + MAX_16_BIT_NUM
#define TOKEN_32BIT_OFST	0xFA // followed by 32-bit value we want to represent, sent directly
#define MAX_8_BIT_NUM		0xF9
#define MAX_16_BIT_NUM		(0xFFFF + MAX_8_BIT_NUM)
#define MAX_24_BIT_NUM		(0xFFFFFF + MAX_16_BIT_NUM)
#define MIN_RUN_LEN		3 //run count does not include first element
#define MAX_RUN_LEN		(0xff + MIN_RUN_LEN)




#endif