## This file is used by NFC NXP NCI HAL(external/libnfc-nci/halimpl/pn547)
## and NFC Service Java Native Interface Extensions (packages/apps/Nfc/nci/jni/extns/pn547)
###############################################################################
# Application options
# Logging Levels
# NXPLOG_DEFAULT_LOGLEVEL    0x01
# ANDROID_LOG_DEBUG          0x03
# ANDROID_LOG_WARN           0x02
# ANDROID_LOG_ERROR          0x01
# ANDROID_LOG_SILENT         0x00
NXPLOG_EXTNS_LOGLEVEL=0x01
NXPLOG_NCIHAL_LOGLEVEL=0x01
NXPLOG_NCIX_LOGLEVEL=0x01
NXPLOG_NCIR_LOGLEVEL=0x01
NXPLOG_FWDNLD_LOGLEVEL=0x01
NXPLOG_TML_LOGLEVEL=0x01
NFC_DEBUG_ENABLED=0x00

###############################################################################
# Nfc Device Node name
NXP_NFC_DEV_NODE="/dev/nq-nci"

###############################################################################
# Extension for Mifare reader enable
MIFARE_READER_ENABLE=0x01

###############################################################################
# Firmware file type
#.so file   0x01
#.bin file  0x02
NXP_FW_TYPE=0x02

###############################################################################
# System clock source selection configuration
#define CLK_SRC_XTAL       1
#define CLK_SRC_PLL        2
NXP_SYS_CLK_SRC_SEL=0x01

###############################################################################
# System clock frequency selection configuration
#define CLK_FREQ_13MHZ         1
#define CLK_FREQ_19_2MHZ       2
#define CLK_FREQ_24MHZ         3
#define CLK_FREQ_26MHZ         4
#define CLK_FREQ_38_4MHZ       5
#define CLK_FREQ_52MHZ         6
NXP_SYS_CLK_FREQ_SEL=0x00

###############################################################################
# The timeout value to be used for clock request acknowledgment
# min value = 0x01 to max = 0x06
NXP_SYS_CLOCK_TO_CFG=0x01

###############################################################################
# NXP proprietary settings
NXP_ACT_PROP_EXTN={2F, 02, 00}

###############################################################################
# NFC forum profile settings
NXP_NFC_PROFILE_EXTN={20, 02, 05, 01, A0, 44, 01, 00}

###############################################################################
# NXP TVDD configurations settings
# Allow NFCC to configure External TVDD, two configurations (1 and 2) supported,
# out of them only one can be configured at a time.
NXP_EXT_TVDD_CFG=0x02

###############################################################################
#config1:SLALM, 3.3V for both RM and CM
NXP_EXT_TVDD_CFG_1={20, 02, 0F, 01, A0, 0E, 0B, 31, 01, 01, 31, 00, 00, 00, 01, 00, D0, 0C}

###############################################################################
#config2: use DCDC in CE, use Tx_Pwr_Req, set CFG2 mode, SLALM,
#monitoring 5V from DCDC, 3.3V for both RM and CM, DCDCWaitTime=4.2ms
NXP_EXT_TVDD_CFG_2={20, 02, 0F, 01, A0, 0E, 0B, 11, 01, 82, 82, 00, BA, 1E, 10, 00, D0, 0C}

###############################################################################
# NXP RF configuration ALM/PLM settings
# This section needs to be updated with the correct values based on the platform
NXP_RF_CONF_BLK_1={
20, 02, 37, 06,
A0, 0D, 03, 24, 03, 80,
A0, 0D, 06, 08, 37, 28, 76, 00, 00,
A0, 0D, 06, 08, 42, 00, 02, FF, FF,
A0, 0D, 06, 06, 42, F8, 60, FF, FF,
A0, 0D, 06, 06, 35, F4, 05, 00, 03,
A0, 69, 09, 01, CF, 80, 00, 00, 07, 40, 00, 00
}

###############################################################################
# NXP RF configuration ALM/PLM settings
# This section needs to be updated with the correct values based on the platform
NXP_RF_CONF_BLK_2={
20, 02, 5B, 01, A0, 0B, 57, F2, 12, 90, 5A, 0F, 4E, 00, 47, 15, B7, AA, 47,
9F, A7, 99, 5C, 9F, 97, 99, 67, 9F, 97, 99, 69, 9F, 97, 00, 73, 9F, 07, 00,
75, 9F, 07, 00, 80, 9F, 07, 00, 84, 9F, 07, 00, 8D, 9F, 07, 00, 8F, 9F, 07,
00, 99, 9F, 04, 00, 9B, 9F, 04, 00, A6, 9F, 04, 00, A8, 9F, 04, 00, B2, 9F,
02, 00, BB, 9F, 00, 00, C1, 9F, 00, 00, CC, 9F, 00, 00, D6, 1F, 00, 00
}

###############################################################################
# NXP RF configuration ALM/PLM settings
# This section needs to be updated with the correct values based on the platform
NXP_RF_CONF_BLK_3={
20, 02, 10, 01, A0, AF, 0C, 83, 43, 7B, 80, 00, 83, 8B, 7B, 80, 00, 77, 08
}

###############################################################################
# NXP RF configuration ALM/PLM settings
# This section needs to be updated with the correct values based on the platform
NXP_RF_CONF_BLK_4={
20, 02, 98, 01, A0, 34, 94, 23, 04, 18, 35, 00, 00, 4B, 00, 00, 71, 00, 00,
71, 00, 00, 96, 00, 00, BC, 00, 00, BC, 00, 00, E1, 00, 00, 07, 01, 00, 07,
01, 00, 2C, 01, 00, 2C, 01, 00, 52, 01, 00, 52, 01, 00, 77, 01, 00, 77, 01,
00, C2, 01, 00, C2, 01, 00, 0D, 02, 00, 0D, 02, 00, 58, 02, 00, 58, 02, 00,
EE, 02, 00, EE, 02, 00, 18, BC, 00, 00, BC, 00, 00, BC, 00, 00, BC, 00, 00,
E1, 00, 00, E1, 00, 00, 2C, 01, 00, 2C, 01, 00, 2C, 01, 00, 2C, 01, 00, 2C,
01, 00, 77, 01, 00, 77, 01, 00, 77, 01, 00, 77, 01, 00, 77, 01, 00, 58, 02,
00, 58, 02, 00, DC, 05, 00, DC, 05, 00, DC, 05, 00, DC, 05, 00, DC, 05, 00,
DC, 05, 00
}

###############################################################################
# NXP RF configuration ALM/PLM settings
# This section needs to be updated with the correct values based on the platform
NXP_RF_CONF_BLK_5={
20, 02, A4, 01, A0, A9, A0, 00, C1, 00, 0A, 01, 80, 41, 0A, 02, 81, 83, 0A,
03, C0, 42, 06, 04, 80, 46, 06, 05, C3, 01, 03, 06, C2, 05, 03, 07, C2, 4A,
03, 07, 81, 01, 01, 08, C3, 8B, 03, 08, C3, 05, 01, 09, C3, 92, 03, 09, C6,
84, 01, 0A, C4, CC, 03, 0A, C6, 89, 01, 0B, C5, D4, 03, 0B, C7, 92, 01, 0C,
44, 00, 03, 0C, C7, C6, 01, 0D, 42, 04, 03, 0D, C9, CE, 01, 0E, 42, 48, 03,
0E, 03, 00, 01, 0F, 43, 50, 03, 0F, 43, 04, 01, 10, 43, 91, 03, 10, 45, 0A,
01, 11, 44, 95, 03, 11, 46, 11, 01, 12, 46, 8E, 01, 13, 47, C5, 01, 14, 48,
CC, 01, 15, 4B, D4, 01, 16, 4E, D7, 01, 17, 45, A2, 01, 18, 46, A6, 01, 19,
46, AE, 01, 1A, 47, B4, 01, 1B, 48, EA, 01, 1C, 49, F0, 01
}

###############################################################################
# NXP RF configuration ALM/PLM settings
# This section needs to be updated with the correct values based on the platform
NXP_RF_CONF_BLK_6={
20, 02, 0C, 01, A0, 18, 08, AC, 00, 28, 01, B2, FE, 9C, 00
}

###############################################################################
# Core configuration extensions
# It includes
# Wired mode settings A0ED, A0EE
# Tag Detector A040, A041, A043
# Low Power mode A007
# Clock settings A002, A003
# PbF settings A008
# Clock timeout settings A004
# eSE (SVDD) PWR REQ settings A0F2
# Window size A0D8
# DWP Speed   A0D5
# How eSE connected to PN553 A012
# UICC2 bit rate A0D1
# SWP1A interface A0D4
# DWP intf behavior config, SVDD Load activated by default if set to 0x31 A037
# SPI CL Sync enable  A098
NXP_CORE_CONF_EXTN={20, 02, 5F, 14,
    A0, 06, 01, 01,
    A0, EC, 01, 01,
    A0, ED, 01, 01,
    A0, 5E, 01, 01,
    A0, 12, 01, 02,
    A0, 40, 01, 01,
    A0, 41, 01, 03,
    A0, 43, 01, 50,
    A0, D1, 01, 02,
    A0, D4, 01, 00,
    A0, 37, 01, 35,
    A0, D8, 01, 02,
    A0, D5, 01, 0A,
    A0, 98, 01, 03,
    A0, 9C, 02, 00, 00,
    A0, AA, 04, F1, 03, EE, 02,
    A0, 38, 04, 1A, 0B, 0B, 00,
    A0, 3A, 08, 19, 00, 19, 00, 19, 00, 19, 00,
    A0, B2, 01, 19,
    A0, 91, 01, 01
}

###############################################################################
# Core configuration rf field filter settings to enable set to 01 to disable set
# to 00 last bit
NXP_CORE_RF_FIELD={ 20, 02, 05, 01, A0, 62, 01, 00 }

###############################################################################
# To enable i2c fragmentation set i2c fragmentation enable 0x01 to disable set
# to 0x00
NXP_I2C_FRAGMENTATION_ENABLED=0x00

###############################################################################
# Core configuration settings
NXP_CORE_CONF={ 20, 02, 2D, 0F,
        85, 01, 01,
        28, 01, 00,
        21, 01, 00,
        30, 01, 08,
        31, 01, 03,
        32, 01, 60,
        38, 01, 01,
        33, 00,
        54, 01, 06,
        50, 01, 02,
        5B, 01, 00,
        80, 01, 01,
        81, 01, 01,
        82, 01, 0E,
        18, 01, 01
}

###############################################################################
#Enable SWP full power mode when phone is power off
NXP_SWP_FULL_PWR_ON=0x00

###############################################################################
#Set the default Felica T3T System Code OffHost route Location :
#This settings will be used when application does not set this parameter
# host  0x00
# eSE   0x01
# UICC  0x02
# UICC2 0x03
DEFAULT_SYS_CODE_ROUTE=0xC0

###############################################################################
# AID Matching platform options
# AID_MATCHING_L 0x01
# AID_MATCHING_K 0x02
AID_MATCHING_PLATFORM=0x01

###############################################################################
#CHINA_TIANJIN_RF_SETTING
#Enable  0x01
#Disable  0x00
NXP_CHINA_TIANJIN_RF_ENABLED=0x01

###############################################################################
#SWP_SWITCH_TIMEOUT_SETTING
# Allowed range of swp timeout setting is 0x00 to 0x3C [0 - 60].
# Timeout in milliseconds, for example
# No Timeout  0x00
# 10 millisecond timeout 0x0A
NXP_SWP_SWITCH_TIMEOUT=0x0A

###############################################################################
# Enable or Disable RF_STATUS_UPDATE to EseHal module
# Disable           0x00
# Enable            0x01
RF_STATUS_UPDATE_ENABLE=0x00

###############################################################################
# Configure the single default SE to use.  The default is to use the first
# SE that is detected by the stack.  This value might be used when the phone
# supports multiple SE (e.g. 0xF3 and 0xF4) but you want to force it to use
# one of them (e.g. 0xF4).
DEFAULT_OFFHOST_ROUTE=0x80

###############################################################################
# Configure the single default SE to use.  The default is to use the first
# SE that is detected by the stack.  This value might be used when the phone
# supports multiple SE (e.g. 0xF3 and 0xF4) but you want to force it to use
# one of them (e.g. 0xF4).
DEFAULT_NFCF_ROUTE=0xC0

###############################################################################
# Configure the default NfcA/IsoDep techology and protocol route. Can be
# either a secure element (e.g. 0xF4) or the host (0x00)
DEFAULT_ROUTE=0x00

###############################################################################
# Vendor Specific Proprietary Protocol & Discovery Configuration
# Set to 0xFF if unsupported
#  byte[0] NCI_PROTOCOL_18092_ACTIVE
#  byte[1] NCI_PROTOCOL_B_PRIME
#  byte[2] NCI_PROTOCOL_DUAL
#  byte[3] NCI_PROTOCOL_15693
#  byte[4] NCI_PROTOCOL_KOVIO
#  byte[5] NCI_PROTOCOL_MIFARE
#  byte[6] NCI_DISCOVERY_TYPE_POLL_KOVIO
#  byte[7] NCI_DISCOVERY_TYPE_POLL_B_PRIME
#  byte[8] NCI_DISCOVERY_TYPE_LISTEN_B_PRIME
NFA_PROPRIETARY_CFG={05, FF, FF, 06, 81, 80, 70, FF, FF}

###############################################################################
# Bail out mode
#  If set to 1, NFCC is using bail out mode for either Type A or Type B poll.
NFA_POLL_BAIL_OUT_MODE=0x01

###############################################################################
# White list of Hosts
# This values will be the Hosts(NFCEEs) in the HCI Network.
DEVICE_HOST_WHITE_LIST={C0, 02}

###############################################################################
# Extended APDU length for ISO_DEP
ISO_DEP_MAX_TRANSCEIVE=0xFEFF

###############################################################################
# Choose the presence-check algorithm for type-4 tag.  If not defined, the default value is 1.
# 0  NFA_RW_PRES_CHK_DEFAULT; Let stack selects an algorithm
# 1  NFA_RW_PRES_CHK_I_BLOCK; ISO-DEP protocol's empty I-block
# 2 NFA_RW_PRES_CHK_ISO_DEP_NAK; Type - 4 tag protocol iso-dep nak presence check
#    command is sent waiting for rsp and ntf.
PRESENCE_CHECK_ALGORITHM=2
###############################################################################
# Configure the NFC Extras to open and use a static pipe.  If the value is
# not set or set to 0, then the default is use a dynamic pipe based on a
# destination gate (see NFA_HCI_DEFAULT_DEST_GATE).  Note there is a value
# for each UICC (where F3="UICC0" and F4="UICC1")
OFF_HOST_ESE_PIPE_ID=0x16
OFF_HOST_SIM_PIPE_ID=0x0A

###############################################################################
#Set the Felica T3T System Code Power state :
#This settings will be used when application does not set this parameter
# bit pos 0 = Switch On
# bit pos 1 = Switch Off
# bit pos 2 = Battery Off
# bit pos 3 = Screen On lock
# bit pos 4 = Screen off unlock
# bit pos 5 = Screen Off lock
DEFAULT_SYS_CODE_PWR_STATE=0x3B

###############################################################################
# Configure the NFCEEIDs of offhost UICC.
# UICC  0x80 (UICC)
OFFHOST_ROUTE_UICC={80}

###############################################################################
# Configure the NFCEEIDs of offhost eSEs.
# eSE   0xC0 (eSE)
OFFHOST_ROUTE_ESE={C0}

###############################################################################
# Configure the list of NFCEE for the ISO-DEP routing.
# host  0x00
# eSE   0xC0 (eSE)
# UICC  0x80 (UICC)
DEFAULT_ISODEP_ROUTE=0x80